通过声辐射模态研究结构声辐射的有源控制

以简支平板为例,通过声辐射模态建立了弹性结构声辐射的有源主动控制策略。并分析了声辐射模态的数学和物理意义。研究发现在中、低频时,声辐射模态对应的辐射效率随着模态阶数的增加而迅速降低。在此基础上,本文提出了一种新的控制策略,即抵消前k阶声辐射模态的伴随系数,使得前k阶声辐射模态的声功率为零。本文以点力作动器作为控制力源进行了数值计算研究。     

The decoupling of the active structural acoustic control based on the theory of radiation modes

With the theory of radiation modes,piezoceramics are used as control actuators in the active control of sound radiation.According to the characteristics of the first four radiation mode shapes,the arrangement of four group of actuators is presented.Theoretical analysis and numerical calculation demonstrate that the four group of actuators can not only reduce the sound power effectively,but also decouple the control equations.While controlling of the sound powers of the first four radiation modes,these actuators can convert the complicated control system with multiple input/output into several simple and independent systems with single input/output.     

基于声辐射模态的有源控制解耦

在声辐射模态有源噪声控制策略框架下,选择压电陶瓷片作为控制作动器。根据前四阶声辐射模态形状特点提出了四种压电作动器位置布置方法。理论分析及数值计算表明,以这种方式布放的压电作动器不仅能有效地降低结构辐射的声功率,而且控制过程中这四组作动器分工明确,从而将控制方程解耦。在控制前几阶声辐射模态声功率时可以将复杂的多输入/多输出控制系统转变为几个简单的、互相独立的单输入/单输出控制系统。     

基于声辐射模态的有源结构声传入及其辐射控制

从辐射模态的概念和角度研究利用结构误差传感方法对弹性封闭空间结构声辐射进行传感和有源控制。首先分析了辐射模态的数学和物理意义并揭示了辐射模态与声腔模态之间的内在耦合关系。通过声辐射模态建立了弹性封闭空间结构声辐射传感和有源控制模型,并提出了通过传感器阵列测量结构表面有限点的振速分布和设计特定的辐射模态空间滤波器来获得控制所需的误差信号。在此基础上对封闭空间结构声辐射有源控制和误差传感策略进行了深入的理论和数值仿真分析,重点讨论了传感器的数量和布放对辐射模态传感及其有源控制效果的影响。结果表明:辐射模态与声腔模态的耦合具有严格的选择性,各阶辐射模态的形状和与相耦合的主导声模态在耦合面上的形状非常相似;利用结构传感技术传感封闭空间的辐射模态时测点不足或空间采样不足将可能产生较严重的模态泄漏问题,使得不希望的结构模态泄露进所测的辐射模态当中来。在低频范围内,一般只需传感并最小化前三阶有效辐射模态声势能,在更低频和空间声模态频率附近,只需最小化前一阶最有效辐射模态声势能,便能和总声势能最小化策略控制效果基本一样。     

基于声辐射模态的有源控制解耦在固定支承板上的研究

基于声辐射模态的主动控制理论,以固定支承板为例,通过四组作动器在固定支承板上的布放,使其能分别控制不同阶声辐射模态辐射的声功率,来使控制方程解耦,从而设计了比较简单与稳定的单输入/单输出控制系统,模拟计算取得了较好的控制效果。同时本文对控制过程中的溢出等问题进行了一定的探讨。     

A compound secondary source for active noise radiation control

Based on the analysis of active noise control system with multi-channel monopole secondary sources, a kind of compound secondary source is proposed in this paper. The proposed compound secondary source consists of two closely located monopole sources with their distance much smaller than a wavelength. The characteristics of the compound source are analyzed, and the performances of the active noise control system with the compound secondary sources on the monopole primary sound field and sound radiated by a plate are investigated both numerically and experimentally. It has been found that the proposed compound secondary sources control system can provide higher noise reduction for free field noise radiation control with the same number of control channels. It is shown that the better performance in noise reduction of the compound secondary sources control system is mainly due to the directivity of the secondary sources where the energy radiation pattern of the compound sources is similar to that of the primary sources.     

应用于有源声辐射控制的一种组合次级声源

在分析多通道单极子次级源控制系统的基础上,提出一种幅度调节型组合次级声源,这种组合源由两个单极子声源构成,单极子声源的间距远小于声波的波长。文中就组合次级源在自由场中对不同初级声源辐射噪声的控制进行理论分析和实验验证,并与同等条件下的单极子次级源控制系统的降噪性能进行了比较分析。数值计算和实验结果均表明,对于不同的初级声场,在次级通道数相同的情况下,组合次级源控制系统可以得到比单极子次级源控制系统高的降噪量。     

Material property estimation for tubes and arteries using ultrasound radiation force and analysis of propagating modes

Arterial elasticity has been proposed as an independent predictor of cardiovascular diseases and mortality. Identification of the different propagating modes in thin shells can be used to characterize the elastic properties. Ultrasound radiation force was used to generate local mechanical waves in the wall of a urethane tube or an excised pig carotid artery. The waves were tracked using pulse-echo ultrasound. A modal analysis using two-dimensional discrete fast Fourier transform was performed on the time-space signal. This allowed the visualization of different modes of propagation and characterization of dispersion curves for both structures. The urethane tube/artery was mounted in a metallic frame, embedded in tissue-mimicking gelatin, cannulated, and pressurized over a range of 10-100 mmHg. The k-space and the dispersion curves of the urethane tube showed one mode of propagation, with no effect of transmural pressure. Fitting of a Lamb wave model estimated Young's modulus in the urethane tube around 560 kPa. Young's modulus of the artery ranged from 72 to 134 kPa at 10 and 100 mmHg, respectively. The changes observed in the artery dispersion curves suggest that this methodology of exciting mechanical waves and characterizing the modes of propagation has potential for studying arterial elasticity.     

Plasmon-induced transparency effect in hybrid terahertz metamaterials with active control and multi-dark modes

We numerically demonstrate a photo-excited plasmon-induced transparency (PIT) effect in hybrid terahertz (THz) metamaterials. The proposed metamaterials are regular arrays of hybrid unit cells composed of a metallic cut wire and four metallic split-ring resonators (SRRs) whose gaps are filled with photosensitive semiconductor gallium arsenide (GaAs) patches. We simulate the PIT effect controlled by external infrared light intensity to change the conductivity of GaAs. In the absence of photo excitation, the conductivity of GaAs is 0, thus the SRR gaps are disconnected, and the PIT effect is not observed since the dark resonator (supported by the hybrid SRRs) cannot be stimulated. When the conductivity of GaAs is increased via photo excitation, the conductivity of GaAs can increase rapidly from 0 S/m to 1×10⁶ S/m and GaAs can connect the metal aluminum SRR gaps, and the dark resonator is excited through coupling with the bright resonator (supported by the cut wire), which leads to the PIT effect. Therefore, the PIT effect can be dynamically tuned between the on and off states by controlling the intensity of the external infrared light. We also discuss couplings between one bright mode (CW) and several dark modes (SRRs) with different sizes. The interference analytically described by the coupled Lorentz oscillator model elucidates the coupling mechanism between one bright mode and two dark modes. The phenomenon can be considered the result of linear superposition of the coupling between the bright mode and each dark mode. The proposed metamaterials are promising for application in the fields of THz communications, optical storage, optical display, and imaging.     

Broadband control of plate radiation using a piezoelectric, double-amplifier active-skin and structural acoustic sensing

The potential of a piezoelectric, double-amplifier active-skin with structural acoustic sensing (SAS) is demonstrated for the reduction of broadband acoustic radiation from a clamped, aluminum plate. The active-skin is a continuous covering of the vibrating portions of the plate with active, independently controllable piezoelectric, double-amplifier elements and is designed to affect control by altering the continuous structural radiation impedance rather than structural vibration. In simulation, acoustic models are sought for the primary and secondary sources that incorporate finite element methods. Simulation indicates that a total radiated power attenuation in excess of 10 dB may be achieved between 250 and 750 Hz with microphone error sensing, while under SAS the radiated power is reduced by nearly 8 dB in the same frequency range. In experiment, the adaptive feed forward filtered-x LMS (least mean square) algorithm, implemented on a Texas Instruments C40 DSP, was used in conjunction with the 6I6O control system. With microphone error sensing, 11.8-dB attenuation was achieved in the overall radiated power between 175 and 600 Hz, while inclusion of SAS resulted in a 7.3-dB overall power reduction in this frequency band.     

具有连续纵向激励模态宽带水声换能器研究

摘要分析了连续纵向激励模态拓宽频带的机理。采用单侧激励，可同时激励奇次模态和偶次模态，利用有限元方法研究了这些模态在水中随几何尺寸变化的规律，通过优化设计制作了接近两个倍频程的宽带换能器样品，其工作带宽为12kHz-44kHz，频带内的起伏为±4．3dB。为进一步减少带宽内响应起伏的大小，通过对模态节点间增加质量钢块以及对后盖板采用机械阻抗匹配腔的方式，制作了工作带宽为12kHz-34kHz，频带内的起伏为±3．7dB的宽带换能器样品。     

结构声辐射的振动模态分析和声辐射模态分析研究

基于辐射声功率的二次型表达式,采用有限元法、Rayleigh积分和边界元法对结构声辐射进行了振动模态分析和声辐射模态分析研究。振动模态间的耦合对辐射声功率影响的研究表明:结构各阶振动模态自身对结构辐射声功率的贡献是增大结构的辐射声功率,而振动模态间的耦合可能会增大结构辐射声功率,也可能会减小结构辐射声功率,或对辐射声功率没有影响。而且,当振动模态间的耦合作用对辐射声功率的影响不大时,采用振动模态控制可取得较好的减振降噪双重控制效果。将混合的Helmholtz积分方程方法用广义逆引入到三维复杂结构声辐射分析的声辐射模态公式中,解决了特征频率下解不唯一问题。还研究了正方形封闭空间结构声辐射模态的辐射效率和形状,并对结构声辐射的振动模态控制和声辐射模态控制进行了讨论。     

The relationship between acoustic radiation modes and structural modes and its applications

Both acoustic radiation modes and structural modes play an important role in the field of structure-borne sound, however, little work has been done for inherent relations between these two kinds of modes. This paper is focused on the relationship between the radiation modes and structural modes and its physical mechanisms. First, a governing equation for relating the radiation mode and structural mode is given based on the characteristics of the modes. Then, using the symmetric or anti-symmetric properties of two kinds of modes, the corresponding relations are presented. And then, numerical examples are given to verify the theoretical investigations, and it has been shown that, for a simply supported rectangular panel vibrating at low frequencies, the first radiation mode is dominant corresponding to (odd, odd) structural modes; the following radiation modes are respectively dominant corresponding to (even, odd), (odd, even), and (even, even) structural modes. Finally, such relations are applied to active acoustic structural control and provide a direct help for the design of active control strategy and arrangement of the secondary forces.     

结构振动模态和声辐射模态之间的对应关系及其应用

声辐射模态和结构振动模态之间的内在关系一直缺乏有效的证明。该文证明并揭示了结构振动模态和声辐射模态之间的对应关系,而且对该关系的有效性和实用性进行了验证。首先从声辐射模态和振动模态的概念出发,利用结构振速的模态叠加特性,建立了两种模态之间的联系方程式;在此基础上根据各种模态形状的对称或反对称性推导出两种模态之间的对应关系;然后对其进行了数值仿真验证。研究表明:对于简支矩形平板而言,在低频范围内,奇-奇振动模态对应的主导声辐射模态是第1阶;偶-奇模态对应第2阶;奇-偶模态对应第3阶;偶-偶模态对应第4阶。最后将这种对应关系应用于结构声辐射有源控制中,通过对主导声辐射模态进行抵消,取得了很好的控制效果。     

Broadband performance of an active headrest.

This paper presents a study of the attenuation of broadband random acoustic disturbances, when using a feedback active headrest system, as originally suggested by Olson and May. Previous studies showed that a practical active headrest can be designed for tonal disturbances using feedforward controllers. However, many applications, such as jet aircraft and cars, require feedback systems to control random disturbances over a wide frequency bandwidth. In this work, robust feedback controllers are designed to control broadband random disturbances in the low-frequency range based on measured data from a laboratory headrest system. The results show that a practically useful performance can be achieved, but only if the controller is designed to minimize the pressure at a "virtual microphone" close to the listener's ears, and that the performance is maintained reasonably well with movements of the listener's head. The paper emphasizes the importance of both the acoustics and the control in the design of broadband active headrest systems.     

基于声辐射模态讨论声能量辐射与传递

声辐射模态表示了振动声源表面的辐射模式。基于声辐射模态讨论了振动声源表面声能量辐射和声场中声能量传递的性质,给出声能量辐射和传递的模式。采用表面声强描述振动声源表面的声能量辐射,采用声强描述声能量在声场中的传递。表面声强和声强可分解成两部分,一部分将辐射的声能量传递到远场;另一部分表现为振动声源与声场之间的能量交换。针对矩形板分析了声能量辐射和传递,数值计算结果与理论结果一致。结果表明基于声辐射模态讨论声能量辐射与传递是可行的和有效的。     

Reduction of sound radiation by using force radiation modes

The location of a vibration source within a machine is sometimes found to have a significant effect upon its radiated acoustic power. It is known that a simple reduction of vibration cannot always reduce the radiated acoustic power, so that treatments based on analysis of a structure’s vibration modes are not always effective. At the same time, radiation mode analysis is known to be a powerful tool for interpreting sound radiation since those modes are independent of a structure’s surface vibration. However, knowledge of the radiation modes alone cannot be used directly to understand the relationship between vibration source location and acoustic power radiation. In this paper, it is shown that the radiation mode concept can be extended to understand the relationship between acoustic power and driving force distribution by considering the product of the structure’s mobility matrix and the radiation modes: the resulting functions are here defined to be force radiation modes (f_rad-modes). An example is presented in which the acoustic power radiated by a simply-supported, baffled beam is reduced by using guidance provided by the structure’s force radiation modes. The results demonstrate that the force radiation modes can be used to guide the reduction of radiated acoustic power by changing the driving force location without the need to perform additional calculations or experiments.     

水下体积目标宽带阵列尺度估计

通过研究目标声纳窄带离散回波模型,论文建立了水下体积目标宽带离散回波模型。并结合均匀线性阵列信号模型,推导出了基于散射亮点形状、距离、方位角等反映目标尺度信息参量的体积目标宽带离散线性均匀阵列回波模型,为水下体积目标探测与尺度估计提供了可靠的理论依据。仿真与实验对比结果证明了模型的正确、有效性,说明了其实用价值。     

Raman active modes of NiSi crystal

Raman scattering intensities of the NiSi Raman-active modes have been calculated with three Raman measurement configurations, which can be used for the symmetry assignment of the NiSi Raman peaks. Raman-active vibrations of the NiSi crystal have also been theoretically studied. Results show that the lattices with A_g and B_2g modes vibrate only in the plane normal to the NiSi[0 1 0] direction while the lattices with B_1g and B_3g modes vibrate only along the NiSi[0 1 0] axis. Based on such study, the relationship between the anisotropic strain distribution in the NiSi thin film and the Raman peak shifts has been briefly discussed.