Photocatalytic reduction of CO<Subscript>2</Subscript> over TiO<Subscript>2</Subscript> based catalysts

At present, carbon dioxide is considered the largest contributor among greenhouse gases. This review covers the current state of problem of carbon dioxide emissions from industrial and combustion processes, the principle of photocatalysis, existing literature related to photocatalytic CO₂ reduction over TiO₂ based catalysts and the effects of important parameters on the process performance including light wavelength and intensity, type of reductant, metal-modified surface, temperature and pressure. Presented at the 34th International Conference of the Slovak Society of Chemical Engineering, Tatranské Matliare, 21–25 May 2007.     

Dry Potassium-Based Sorbents for CO<Subscript>2</Subscript> Capture

Dry potassium-based sorbents were prepared by impregnation with potassium carbonate on supports such as activated carbon (AC), TiO₂, Al₂O₃, MgO, CaO, SiO₂ and various zeolites. The CO₂ capture capacity and regeneration property of various sorbents were measured in the presence of H₂O in a fixed bed reactor, during multiple cycles at various temperature conditions (CO₂ absorption at 50–100 °C and regeneration at 130–400 °C). The KAlI30, KCaI30, and KMgI30 sorbents formed new structures such as KAl(CO₃)₂(OH)₂, K₂Ca(CO₃)₂, K₂Mg(CO₃)₂, and K₂Mg(CO₃)₂·4(H₂O), which did not completely convert to the original K₂CO₃ phase at temperatures below 200 °C, during the CO₂ absorption process in the presence of 9 vol.% H₂O. In the case of KACI30, KTiI30, and KZrI30, only a KHCO₃ crystal structure was formed during CO₂ absorption. The formation of active species, K₂CO₃·1.5H₂O, by the pretreatment with water vapor and the formation of the KHCO₃ crystal structure after CO₂ absorption are important factors for absorption and regeneration, respectively, even at low temperatures (130–150 °C). In particular, the KTiI30 sorbent showed excellent characteristics with respect to CO₂ absorption and regeneration in that it satisfies the requirements of a large amount of CO₂ absorption (87 mg CO₂/g sorbent) without the pretreatment with water vapor, unlike KACI30, and a fast and complete regeneration at a low temperature condition (1 atm, 150 °C). In addition, the higher total CO₂ capture capacity of KMgI30 (178.6 mg CO₂/g sorbent) than that of the theoretical value (95 mg CO₂/g sorbent) was explained through the contribution of the absorption ability of MgO support. In this review, we introduce the CO₂ capture capacities and regeneration properties of several potassium-based sorbents, the changes in the physical properties of the sorbents before/after CO₂ absorption, and the role of water vapor and its effects on CO₂ absorption.     

Fast CO<Subscript>2</Subscript> sequestration by aerogel composites

The increasingly evident impact of anthropogenic CO₂ emissions on climate change and associated environmental effects is stimulating the search for viable methods to remove this gas. One of the most promising strategies is the long-term storage of CO₂ in inert, insoluble and thermodynamically-stable materials. This strategy mimics the natural reactions that transform silicates into carbonates regulating the cycle of CO₂ on the surface of the Earth, operating on a geological time-scale. Consequently, the aim is to accelerate these reactions to be applicable on the timescale of human lives. We present the various technologies developed or proposed to date, based on this particular approach. The principal limiting factor is that high pressures and temperatures are required to produce appropriate materials capable of CO₂ sequestration and storage. Nevertheless, the synthetic materials known as aerogels can be modified in shape, size and chemical functionality so as to catalyse the process of CO₂ elimination through silicates (of Ca or Mg), considerably reducing the reaction time and working at atmospheric pressure and temperature.     

Effect of PEG with different <Emphasis Type="Italic">M</Emphasis><Subscript>W</Subscript> as template direction reagent on preparation of porous TiO<Subscript>2</Subscript>/SiO<Subscript>2</Subscript> with assistance of supercritical CO<Subscript>2</Subscript>

Titania–silica composite have been prepared using polyethylene glycol (PEG) with different molecular weights (M _w), PEG20000, PEG10000, and PEG2000, as template in supercritical carbon dioxide (SC CO₂). The composite precursors were dissolved in SC CO₂ and impregnated into PEG templates using SC CO₂ as swelling agent and carrier. After removing the template by calcination at suitable temperature, the titania–silica composite were obtained. The composite were characterized by X-ray diffraction, Fourier transform infrared spectroscopy, and nitrogen sorption–desorption experiment. Photocatalytic activity of the samples has been investigated by photodegradation of methyl orange. Results indicate that there are many Si–O–Ti linkages in the TiO₂/SiO₂ composite; the PEG template has a significant influence on the structure of TiO₂/SiO₂. In addition, the TiO₂/SiO₂ prepared with PEG10000 exhibited high photocatalytic efficiency. So this work supplies a clue to control and obtain the TiO₂/SiO₂ composite with different photocatalytic reactivity with the aid of suitable PEG template in supercritical CO₂.     

Investigation of miniature CO<Subscript>2</Subscript> gas sensor based on NASICON

A miniature CO₂ gas sensor based on NASICON (sodium super ionic conductor) thick film was fabricated. The solid-electrolyte NASICON material was synthesized through an inorganic-reagent-based sol-gel method. The resulting materials were characterized by means of X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS). NASICON paste was coated on a piece of alumina substrate attached to a platinum heater. Li₂CO₃-BaCO₃ binary carbonate in molar ratio 1 : 1.5 was utilized as the sensing electrode. Within a wide range of CO₂ volume ratio concentration from 500 to 5000 ppm, the output electromotive force (EMF) of the sensor followed Nernst equation well at high working temperature. The response and recovery times were 20 and 58 s, respectively. This miniature CO₂ gas sensor possessed extra merits such as low power consumption, miniaturized framework, and easy fabrication.     

Effect of sodium cation on the electrochemical reduction of CO<Subscript>2</Subscript> at a copper electrode in methanol

The electrochemical reduction of CO₂ with a Cu electrode in methanol was investigated with sodium hydroxide supporting salt. A divided H-type cell was employed; the supporting electrolytes were 80 mmol dm⁻³ sodium hydroxide in methanol (catholyte) and 300 mmol dm⁻³ potassium hydroxide in methanol (anolyte). The main products from CO₂ were methane, ethylene, carbon monoxide, and formic acid. The maximum current efficiency for hydrocarbons (methane and ethylene) was 80.6%, at −4.0 V vs Ag/AgCl, saturated KCl. The ratio of current efficiency for methane/ethylene, r _f(CH₄)/r _f(C₂H₄), was similar to those obtained in LiOH/methanol-based electrolyte and larger relative to those in methanol using KOH, RbOH, and CsOH supporting salts. In NaOH/methanol-based electrolyte, the efficiency of hydrogen formation, a competing reaction of CO₂ reduction, was suppressed to below 4%. The electrochemical CO₂ reduction to methane may be able to proceed efficiently in a hydrophilic environment near the electrode surface provided by sodium cation.     

CO<Subscript>2</Subscript> corrosion inhibition by hydroxyethyl,aminoethyl, and amidoethyl imidazolines in water–oil mixtures

The corrosion behavior of hydroxyethyl, amino ethyl and amid ethyl imidazolines corrosion inhibitors was evaluated by using potenthiodynamic polarization curves, linear polarization resistance, and electrochemical impedance spectroscopy techniques. Solutions included deaerated 3% NaCl, 3% NaCl+diesel saturated with CO₂ at 50 °C with and without inhibitors. Regardless of the presence of diesel, the corrosion rate was decreased with the addition of the inhibitors, but the time to reach a steady state was longer than when the oily part, i.e., diesel, was present. In the absence of the oily part, the impedance results showed that the film formed was porous, allowing the electrolyte to diffuse through it and corrode the metal. When the oily part was present, the film formed was much more stable, not porous, and did not allow the electrolyte to corrode the sample. The most efficient inhibitor was the amid ethyl imidazoline, whereas the least efficient was the hydroxyethyl imidazoline, because the film formed by the former was much more stable from the beginning of the test.     

Application of thermogravimetric analysis to the evaluation of aminated solid sorbents for CO<Subscript>2</Subscript> capture

In this work a series of solid sorbents were synthesized by immobilizing liquid amines on the surface of a mesoporous alumina. The samples were chemically characterized and BET surface areas calculated from the N₂ adsorption isotherms at 77 K. The CO₂ capture performance of the sorbents and their thermal stability was studied by thermogravimetric methods. The effect of amine loading on the CO₂ capture performance of the prepared sorbents was also evaluated. Analysis of TG-DTG curves showed that thermal stabilization of the amines is significantly improved by immobilizing them on an inorganic support. Temperature-programmed CO₂ adsorption tests from 298 K up to 373 K at atmospheric pressure, proved to be a useful technique for assessing the capacity of sorbents for CO₂ capture. Alumina impregnated with diethylenetriamine presented the highest CO₂ adsorption capacities throughout the tested temperature range.     

High temperature adsorption of CO<Subscript>2</Subscript> on various hydrotalcite-like compounds

A study was conducted to describe and quantify how substitution of the divalent cation and interlayer charge compensating anions affect the CO₂ adsorptive capacity of various hydrotalcite-like compounds (HTlcs). Physical and chemical properties of the HTlcs were evaluated using a number of methods and the CO₂ adsorption rate and capacity were measured at elevated temperature (603 K). The results showed that the synthetic analogue of the naturally occurring hydrotalcite mineral, [Mg_0.73Al_0.27(OH)₂](CO₃)_0.13⋅xH₂O, had the best overall adsorption capacity and kinetics. The stability of the adsorption capacity was tested by subjecting the model HTlc to 10 equilibrium adsorption and desorption cycles. At the end of the cycle, the HTlc had maintained approximately sixty-five percent of its initial capacity. Temperature programmed desorption of CO₂ was used to quantify the surface basicity of the various HTlcs. The results showed that the reversible physisorption portion of the CO₂ isotherm was correlated to the number of surface basic sites on the HTlcs.     

Modeling the active centers of V<Subscript>2</Subscript>O<Subscript>5</Subscript>/SiO<Subscript>2</Subscript> and V<Subscript>2</Subscript>O<Subscript>5</Subscript>/TiO<Subscript>2</Subscript> supported catalysts. DFT theoretical analysis of optical properties

Within the framework of the density functional theory (DFT), the electronic structure of monooxodioxovanadium functional groups in tetrahedral coordination, which model the active centers (ACs) of fine supported catalysts V₂O₅/SiO₂ and V₂O₅/TiO₂, has been analyzed. The optimal structures of three ACs as possible models of monomeric and polymeric oxovanadium forms on the carriers with low vanadium content were determined. The modified DFT method involving the time dependence of Kohn-Sham equation (TDDFT) was used for the adopted AC models to calculate the energies of the excited states, and optical spectra of the absorption in 25000–60000 cm^?1 region were reconstructed on their base. The spectrum in this region is due to O → V charge transfer. The features of electronic spectra with the charge transfer for V₂O₅/SiO₂ and V₂O₅/TiO₂ catalysts and the vibrational spectra of three AC models corresponding to the monomeric and dimeric oxovanadium forms of the supported catalysts V₂O₅/SiO₂ and V₂O₅/TiO₂ were defined. The detailed interpretation of normal vibration frequencies is given. The frequencies typical of the monomeric and dimeric oxovanadium forms on the carrier surface were identified.     

CO<Subscript>2</Subscript> adsorption and dehydration behavior of LiNaX,KNaX, CaNaX and CeNaX zeolites

In this study, NaX synthetic zeolite was modified by following the conventional cation exchange method at 70°C. 82, 81, 79 and 48% of sodium were exchanged with Li⁺, K⁺, Ca2⁺ and Ce3⁺, respectively. Thermal analysis data obtained by TG/DSC was used to evaluate the dehydration behavior of the zeolites. The strongest interaction with water and the highest dehydration enthalpy (ΔH) value were found for Li-exchanged form and compared with the other forms. The temperature required for complete dehydration increased with decreasing cation size (cation size: K⁺>Ce³⁺>Ca2⁺>Na⁺>Li⁺). CO₂ adsorption at 5 and 25°C was also studied and the virial model equation was used to analyze the experimental data to calculate the Henry’s law constant, K _o and isosteric heat of adsorption at zero loading Q _st. K _o values decreased with increasing temperature and the highest Qst was obtained for K rich zeolite. It was observed that both dehydration and CO₂ adsorption properties are related to cation introduced into zeolite structure.     

Theoretical study on the reaction mechanism of (CH<Subscript>3</Subscript>)<Subscript>3</Subscript>CO<Superscript>.</Superscript> radical with NO

The reaction mechanism of (CH₃)₃CO^. radical with NO is theoretically investigated at the B3LYP/6-31G* level. The results show that the reaction is multi-channel in the single state and triplet state. The potential energy surfaces of reaction paths in the single state are lower than that in the triple state. The balance reaction: (CH₃)₃CONO⇔(CH₃)₃CO^.+NO, whose potential energy surface is the lowest in all the reaction paths, makes the probability of measuring (CH₃)₃CO^. radical increase. So NO may be considered as a stabilizing reagent for the (CH₃)₃CO^. radical.     

Facilitated Transport of C<Subscript>2</Subscript>H<Subscript>4</Subscript> in a SiO<Subscript>2</Subscript>-poly(N-vinylpyrrolidone)-Ag<Superscript>+</Superscript> Inorganic-Organic Hybrid Membrane

Inorganic-organic hybrid membranes containing silica as the structure matrix, poly(N-vinylpyrrolidone) (PVP) as the organic mediating agent and silver ions as olefinic carriers were prepared using sol–gel method and dip-coating process. The structure and permeances of the membranes for N₂, He, C₂H₄, C₂H₆ at different temperatures indicated that defect-free membranes were obtained and the transportation of the C₂H₄ through the membranes followed the dissolution and diffusion mechanism. Ideal separation factors of C₂H₄/C₂H₆ through the membranes were evaluated at the temperature of 298, 373 and 423 K respectively using mixture gas of 50% C₂H₄-50% C₂H₆. The results showed that the ideal separation factors of C₂H₄/C₂H₆ through the membranes were obviously greater than the ratio of PC₂H₄/PC₂H₆ obtained from the single gas measurement due to the hindering effect by the adsorbed C₂H₄. The ideal separation factors of C₂H₄/C₂H₆ increased with temperature and reached 10 at 423 K, which suggested that C₂H₄ and C₂H₆ could be separated at lower humidity compared to the reported organic polymer/silver salt membranes in which humidified gases and higher silver loading were usually used. The transport of C₂H₄ in the inorganic-organic hybrid membrane was proposed to follow the hopping mechanism, that is, olefins moved across the fixed silver sites.     

LiMn<Subscript>2</Subscript>O<Subscript>4</Subscript> and LiCoO<Subscript>2</Subscript> composite cathode materials obtained by mechanical activation

New composite cathode materials xLiMn₂O₄/(1 ? x) LiCoO₂(x = 0.7, 0.6, 0.5 и 0.4) were obtained by mechanical activation. According to scanning electron microscopy data, the process was accompanied by pronounced dispersion and fine mixing of the initial components. In the course of the preparation and electrochemical cycling of the composites, LiMn₂O₄ and LiCoO₂ partially reacted, leading to the replacement of manganese with cobalt in the structure of spinel, which was detected by powder X-ray diffraction (XRD), IR and X-ray photoelectron spectroscopy (XPS), and cyclic chronopotentiometry. The specific discharge capacity of composites was ～100 mAh/g.     

Preparation of novel visible-light-driven In<Subscript>2</Subscript>O<Subscript>3</Subscript>–CaIn<Subscript>2</Subscript>O<Subscript>4</Subscript> composite photocatalyst by sol–gel method

Novel visible-light-activated In₂O₃–CaIn₂O₄ photocatalysts were developed in this paper through a sol–gel method. The photocatalytic activities of In₂O₃–CaIn₂O₄ composite photocatalysts were investigated based on the decomposition of methyl orange under visible light irradiation (λ > 400 nm). The obtained samples were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), energy dispersive spectrum (EDS), X-ray photoelectron spectroscopy (XPS) and UV–vis diffused reflectance spectroscopy (DRS). The results revealed that the In₂O₃–CaIn₂O₄ composite samples with different In₂O₃ and CaIn₂O₄ content can be obtained by controlling the synthesis temperature, and the composite photocatalysts extended the light absorption spectrum toward the visible region. The photocatalytic tests indicated that the composite samples demonstrated high visible-light activity for decomposition of methyl orange. The significant enhancement in the In₂O₃–CaIn₂O₄ photo-activity under visible light irradiation can be ascribed to the efficient separation of photo-generated carriers in the In₂O₃ and CaIn₂O₄ coupling semiconductors.     

Quantum-chemical modelling of nanotubes of titanium silicocarbides Ti<Subscript>2</Subscript>SiC,Ti<Subscript>3</Subscript>SiC<Subscript>2</Subscript>, and Ti<Subscript>4</Subscript>SiC<Subscript>3</Subscript>

Atomic models are proposed for nanotubes of the titanium silicocarbides Ti₂SiC, Ti₃SiC₂, and Ti₄SiC₃, and their electronic structure and interatomic interactions are investigated by the density functional tight-binding method (DFTB) in comparison with the corresponding crystalline phases. Translated from Teoreticheskaya i éksperimental’naya Khimiya, Vol. 45, No. 2, pp. 88-92, March-April, 2009.     

Ionic conduction of a high-temperature modification of Lu<Subscript>2</Subscript>Ti<Subscript>2</Subscript>O<Subscript>7</Subscript>

A nanoceramic product of the composition Lu₂Ti₂O₇ is synthesized by a coprecipitation method with a subsequent sublimation drying and an annealing at 650–1650°C. The conduction of Lu₂Ti₂O₇ synthesized at 1650°C is ionic (10^–3 S cm^–1 at 800°C). Thus, a new material with a high ionic conduction has been discovered. The ordering in Lu₂Ti₂O₇ is studied by methods of RFA, RSA, IK spectroscopy, electron microscopy, and impedance spectroscopy. The existence of a low-temperature phase transition fluorite-pyrochlore at 800°C and a high-temperature conversion order-disorder at 1650°C are established.Translated from Elektrokhimiya, Vol. 41, No. 3, 2005, pp. 298–303.Original Russian Text Copyright © 2005 by Shlyakhtina, Ukshe, Shcherbakova.     

Temperature dependence of the polarization resistance of the O<Subscript>2</Subscript>,Au/La<Subscript>0.88</Subscript>Sr<Subscript>0.12</Subscript>Ga<Subscript>0.82</Subscript>Mg<Subscript>0.18</Subscript>O<Subscript>2.85</Subscript> electrode system

The impedance of a porous gold electrode in contact with solid electrolyte La_0.88Sr_0.12Ga_0.82Mg_0.18O_2.85 and the effect of the manufacture conditions on its polarization resistance are studied at 600–800°C in air. The overall oxygen reaction rate on a gold electrode is described as the sum of two partial constituents, namely, the oxygen exchange at the gas/electrolyte interface at the gold/gas/electrolyte triple-phased boundary.Translated from Elektrokhimiya, Vol. 41, No. 2, 2005, pp. 190–197.Original Russian Text Copyright © 2005 by Shkerin, Sokolova, Khlupin, Beresnev.This revised version was published online in April 2005 with corrections to the article note and article title and cover date.     

Phase relations in the CoO–V<Subscript>2</Subscript>O<Subscript>5</Subscript>–Fe<Subscript>2</Subscript>O<Subscript>3</Subscript> system in subsolidus area

Thermal properties of Co₂FeV₃O₁₁ have been reinvestigated. It has been proved that this compound does not exhibit polymorphism. It melts incongruently at the temperature of 770±5°C and the phase with lyonsite type structure is the solid product of this melting. Phase relations in the whole subsolidus area of the CoO–V₂O₅–Fe₂O₃ system have been determined. The solidus area projection onto the component concentration triangle plane of this system has been constructed using the DTA and XRD methods. 15 subsidiary subsystems can be distinguished in this system.