Fast, sensitive and cost-effective detection of nerve agents in the gas phase using a portable instrument and an electrochemical biosensor

The nerve agents are chemical warfare agents known to be used during terrorist attacks. An inexpensive and portable system to be used by first responders and military personnel is of interest owing to the continuing threat of possible terrorist attacks. Amperometric biosensors based on cholinesterase inhibition show such potentialities. In this work butyrylcholinesterase was immobilized onto screen-printed electrodes modified with Prussian blue and the nerve agent detection was performed by measuring the residual activity of enzyme. The optimized biosensor was tested with sarin and VX standard solutions, showing detection limits of 12 and 14 ppb (10% of inhibition), respectively. The enzymatic inhibition was also obtained by exposing the biosensors to sarin in gas phase. Two different concentrations of sarin gas (0.1 and 0.5 mg m⁻³) at different incubation times (from 30 s up to 10 min) were tested. It is possible to detect sarin at a concentration of 0.1 mg m⁻³ with 30-s incubation time, with a degree of inhibition of 34%, which match the legal limits (immediate danger to life and health).     

Sequential injection/electrochemical immunoassay for quantifying the pesticide metabolite 3,5,6-trichloro-2-pyridinol

An automated and sensitive sequential injection electrochemical immunoassay was developed to monitor a potential insecticide biomarker, 3,5,6-trichloro-2-pyridinol. The current method involved a sequential injection analysis (SIA) system equipped with a thin-layer electrochemical flow cell and permanent magnet, which was used to fix 3,5,6-trichloro-2-pyridinol (TCP) antibody coated magnetic beads (TCP-Ab-MBs) in the reaction zone. After competitive immunoreactions among TCP-Ab-MBs, TCP analyte, and horseradish peroxidase (HRP) labeled TCP, a 3,3′,5,5′-tetramethylbenzidine dihydrochloride and hydrogen peroxide (TMB-H₂O₂) substrate solution was injected to produce an electroactive enzymatic product. The activity of HRP tracers was monitored by a square wave voltammetric scanning electroactive enzymatic product in the thin-layer flow cell. The voltammetric characteristics of the substrate and the enzymatic product were investigated under batch conditions, and the parameters of the immunoassay were optimized in the SIA system. Under the optimal conditions, the system was used to measure as low as 6 ng L⁻¹(ppt) TCP, which is around 50-fold lower than the value indicated by the manufacturer of the TCP RaPID Assay^® kit (0.25 μg/L, colorimetric detection). The performance of the developed immunoassay system was successfully evaluated on tap water and river water samples spiked with TCP. This technique could be readily used for detecting other environmental contaminants by developing specific antibodies against contaminants and is expected to open new opportunities for environmental and biological monitoring.     

Flow injection electrochemical enzyme immunoassay based on the use of an immunoelectrode strip integrate immunosorbent layer and a screen-printed carbon electrode

A flow injection amperometric immunoassay system based on the use of screen-printed carbon electrode for the detection of mouse IgG was developed. An immunoelectrode strip, on which an immunosorbent layer and screen-printed carbon electrode were integrated, and a proposed flow cell have been fabricated. The characterization of the flow immunoassay system and parameters affecting the performance of the immunoassay system were studied and optimized. Amperometric detection at 0.0 V (versus Ag/AgCl) resulted in a linear detection range of 30-700 ng ml⁻¹, with a detection limit of 3 ng ml⁻¹. The signal variation among electrode strips prepared from variant batch did not exceed 8.5% (n=7) by measuring 0.5 μg ml⁻¹ antigen standard solution.     

Development of xylitol oxidase-based flow injection analysis for monitoring of xylitol concentrations

A flow injection method for monitoring xylitol was developed using xylitol oxidase (XYO) immobilized on a VA-Epoxy Biosynth E3-support. The immobilized XYO cartridge had a good operational lifetime (up to 24 h) and storage stability (up to 1 month). The XYO-FIA system with an oxygen electrode was investigated systematically regarding the factors that can affect enzyme activity, such as pH, reaction temperature, carrier solution and sample matrix. In order to attain high activity of the immobilized XYO, potassium phosphate solution (1 M) with 0.5 g l⁻¹ Triton X-100 adjusted to pH 8.5 was used as the carrier solution. Sample matrix effects on the immobilized XYO were also investigated. High concentrations of some components (arabinose, 20 g l⁻¹; xylose, 30 g l⁻¹; NaCl, 30 g l⁻¹) in the sample had significant inhibitory effects on the response of the XYO-FIA system. The performance of the XYO-FIA system was tested by using different sample injection volumes (75-250 μl) and carrier flow rates (0.7-2.0 ml min⁻¹).     

Flow Injection Analysis of Chloramphenicol by Using a Disposable Wall‐Jet Ring Disk Carbon Electrode

A preanodized screen‐printed ring disk carbon electrode was applied to the determination of chloramphenicol (Ph? NO₂, CAP) by flow injection analysis (FIA). By setting up the first irreversible reduction reaction of Ph? NO₂ to Ph? NHOH at the disk electrode, the following reversible oxidation of hydroxylamine (Ph? NHOH) to the nitroso (Ph? NO) derivative can be monitored/collected at the ring electrode for CAP analysis. The interference from dissolved oxygen and others can thus be avoided by using this approach and precise CAP determination can be easily performed by FIA under aerobic conditions. Preanodization treatment helps to lower the overpotential of the electrochemical reaction of CAP and favors the selective detection in aqueous medium. Under the optimum conditions, ten repetitive determinations at 1 μM and 10 μM CAP resulted in relative standard deviations of less than 4%, indicating good reproducibility of the system. A linear calibration range of 0.1–20 μM with a detection limit of 0.074 μM (S/N=3) was obtained. Veterinary pharmaceutics were finally analyzed by this sensor to validate its practical applicability.     

Liposome-based flow injection enzyme immunoassay for theophylline

Preliminary results are presented on the development of a sensitive, quantitative immunoassay based on a regenerable, flow injection analysis system incorporating a double-amplification approach. The double amplification is achieved by means of liposome-encapsulated peroxidase enzyme molecules which are released subsequent to a competitive immunological reaction with analyte molecules for immobilized antibodies. The released peroxidase enzymatically cleaves, from an organofluorine substrate, fluoride ions which are then potentiometrically measured. The entire process is carried out in a flow injection analysis system. The competition between the analyte molecules (theophylline) and theophylline-derivatized liposomes for immobilized antibody sites in flow-through immunoreactor column results in unbound liposomes being carried downstream where they are ruptured in the presence of hydrogen peroxide andp-fluorophenol. The peroxidase molecules released react enzymatically to produce fluoride ions which are measured with an ion-selective electrode. The immunoreactor column is then regenerated with a chaotropic agent and the next sample or calibration solution is injected. By means of column regeneration and calibration, accurate quantitation can be achieved; a feature missing from conventional batch-type immunoassays. By means of this liposome/enzyme double-amplification approach, theophylline was determined over a range of concentrations from 0.2 to 4000 ng/ml. The detection limit of 200 pg/ml corresponds to about 100 femtomole of theophylline measured in the 100 l sample injected.Dedicated to Professor W. Simon on the occasion of his 60th birthday     

Electrochemical Oxidation and Sensitive Determination of Acetaminophen in Pharmaceuticals at Poly(3,4‐ethylenedioxythiophene)‐Modified Screen‐Printed Electrodes

The current study reports electrocatalytic oxidation of acetaminophen at screen‐printed electrode (SPE) modified with electrogenerated poly(3,4‐ethylenedioxythiophene) (PEDOT) film. Cyclic voltammetric studies show that the SPE/PEDOT electrode lowers overpotentials and improves electrochemical behavior of acetaminophen (ACAP) in aqueous buffer solutions, compared to the bare SPE. Excellent analytical features are achieved, including high sensitivity, low detection limit and satisfactory dynamic range, by cyclic voltammetry (CV), differential pulse voltammetry (DPV) and flow‐injection amperometry (FIA) under optimized conditions. The proposed methods obtain satisfactory results in detection of acetaminophen in two commercial tablets.     

Reversed flow injection and sandwich sequential injection methods for the spectrophotometric determination of copper(II) with cuprizone

Two new flow methods, flow injection analysis (FIA) and sequential injection analysis (SIA), for the spectrophotometric determination of Cu(II) in water at trace levels have been developed and optimised. Both methods are based on the reaction with oxalic acid bis(cyclohexylidene hydrazide) (cuprizone) in alkaline media. The two procedures have been developed for the final aim to compare their performances and to offer new rapid heavy metals analysis tools, avoiding the use of extraction steps. A detailed study of the physico-chemical parameters affecting the systems performances has been carried out. The reversed FIA and sandwich SIA approaches offered the best sensitivity. In both cases, an extremely good linearity has been obtained within the range 0.06-4 μg ml⁻¹ (correlation coefficient r=0.9999), whereas the observed detection limits were 0.013 and 0.004 μg ml⁻¹, for FIA and SIA, respectively. Furthermore, due to the great similarity of the diffusion zones in the reaction slugs, our approach offers the opportunity to compare the two methods in analogous conditions. This SIA method, besides keeping its typical reagent saving features, offered analytical performances equivalent to those of FIA. To obtain these results, an original “stop-flow like” method was successfully employed in the SIA approach. Both methods were validated by analysis of real water samples, after copper addition, and certified reference samples of fortified and waste waters.     

Sequential injection chemiluminescence immunoassay for anionic surfactants using magnetic microbeads immobilized with an antibody

A rapid and sensitive immunoassay for the determination of linear alkylbenzene sulfonates (LAS) is described. The method involves a sequential injection analysis (SIA) system equipped with a chemiluminescence detector and a neodymium magnet. Magnetic beads, to which an anti-LAS monoclonal antibody was immobilized, were used as a solid support in an immunoassay. The introduction, trapping and release of the magnetic beads in the flow cell were controlled by means of a neodymium magnet and adjusting the flow of the carrier solution. The immunoassay was based on an indirect competitive immunoreaction of an anti-LAS monoclonal antibody on the magnetic beads and the LAS sample and horseradish peroxidase (HRP)-labeled LAS, and was based on the subsequent chemiluminscence reaction of HRP with hydrogen peroxide and p-iodophenol, in a luminol solution. The anti-LAS antibody was immobilized on the beads by coupling the antibody with the magnetic beads after activation of a carboxylate moiety on the surface of magnetic beads that had been coated with a polylactic acid film. The antibody immobilized magnetic beads were introduced, and trapped in the flow cell equipped with the neodymium magnet, an LAS solution containing HRP-labeled LAS at constant concentration and the luminol solution were sequentially introduced into the flow cell based on an SIA programmed sequence. Chemiluminescence emission was monitored by means of a photon counting unit located at the upper side of the flow cell by collecting the emitted light with a lens. A typical sigmoid calibration curve was obtained, when the logarithm of the concentration of LAS was plotted against the chemiluminescence intensity using various concentrations of standard LAS samples (0-500 ppb) under optimum conditions. The time required for analysis is less than 15 min.     

Flow Injection Analysis of Ascorbyl Glucoside in Cosmetics by a Disposable Printed‐Circuit Board Waste Modified Electrode

Ascorbyl glucoside, i.e., ascorbic acid 2‐glucoside (AA‐2G), is anew type of stable vitamin C derived compound used in many cosmetic skin‐lightening formulations, but rarely studied in the literature. In this study, a screen printed electrode modified with copper‐enriched printed circuit‐board waste (designated as Cu_PCB/SPE) was applied to study the electrochemical characteristics of AA‐2G. Cyclic voltammogram of the Cu_PCB/SPE showed an electrocatalytic oxidative feature at ?0.6 V vs. Ag/AgCl in 0.15 M NaOH solution. Flow injection analysis coupled with the Cu_PCB/SPE was further developed for sensitive AA‐2G determination. The calibration plot was linear in the window of 2.5–160 ppm with slope and regression coefficient of 0.0169 μA/ppm and 0.9971, respectively. The detection limit (S/N = 3) was 0.247 ppm. Real sample analysis was demonstrated for different skin‐lightening cosmetic products with appreciable results.     

Development of a flow manifold for Fe(III) ion determination with a fluoride ion-selective electrode

Continuous-flow (CF) and flow-injection (FI) analysis using the fluoride ion-selective electrode (FISE) as detector have been investigated. The measurements were performed in a home-made cell under appropriate flow conditions (2.86 or 3.45 ml min⁻¹, 0.2 ml samples, 10⁻⁶ M sodium fluoride). The calibration graph was obtained by plotting the signal height versus concentration of iron in the range of Fe(III) concentration from 10⁻⁵ to 10⁻¹ M in acetate buffer (pH 2.8 or 3.4). In all described procedures, the range of linear response extends to the Fe(III) concentration from 1×10⁻³ to 1×10⁻¹ M, with detection limit 9×10⁻⁵ M. The effect of double-line, two-line flow manifold and CF was investigated and discussed.     

Development of an amperometric immunosensor based on flow injection analysis for the detection of red blood cells

An amperometric immunosensor, based on a non-competitive sandwich assay and flow injection analysis (FIA), was developed for the detection of human red blood cells (RBCs). A dual working electrode, on which specific IgM and nonspecific IgM were chemically immobilised to form sensing and blank electrodes, respectively, was employed to determine the binding of specific blood cells and non-specific adsorption in one determination. Horseradish peroxidase (HRP)-labelled antiblood group A IgM was used in the assay. Sensor preparation involved chemical immobilisation of the IgMs on glassy carbon electrodes using l-ethyl-3(3-dimethyl aminopropyl)carbodiimide (EDC) as a coupling reagent in the presence of N-hydroxysuccinimide (NHS). The interference contributions, such as the non-specific adsorption of the enzyme conjugate and the blood cells, were determined and removed. A quantitative relationship between the cell binding response and its concentration was obtained in the region 1 − 30 × 10⁸ cells ml⁻¹.     

4-Amino-1-naphthylphosphate as a substrate for the amperometric detection of alkaline phosphatase activity and its application for immunoassay

Immunosensors and biochemical array detection systems based on electrochemical transducers have many advantages such as low detection limit, fast response, simple design and ease of miniaturization. However, further development of such sensors will depend on the availability of suitable substrates that can be converted by a labeling enzyme to an electrochemically active product. Here, we report the synthesis of 4-amino-1-naphthylphosphate and it’s application as a new substrate for alkaline phosphatase. The electrochemical and enzymatic properties of this compound were investigated and compared with the properties of other aromatic 1,4-dihydroxy and 1,4-hydroxy-amine derivatives. The product of the enzyme reaction was 4-aminonaphthol, which was rapidly converted in the presences of air to 1,4-iminonaphthoquinone. This compound could then be detected in an amperometric flow injection assay (AFIA) with −200 mV versus Ag/AgCl potential application. The analytical range for mouse IgG, in an alkaline phosphatase amplified sandwich immuoassay with amperometric detection, was 0.01-100 μg ml⁻¹.     

A flow injection method for the analysis of tetracycline antibiotics in pharmaceutical formulations using electrochemical detection at anodized boron-doped diamond thin film electrode

A method using flow injection (FI) with amperometric detection at anodized boron-doped diamond (BDD) thin films has been developed and applied for the determination of tetracycline antibiotics (tetracycline, chlortetracycline, oxytetracycline and doxycycline). The electrochemical oxidation of the tetracycline antibiotics was studied at various carbon electrodes including glassy carbon (GC), as-deposited BDD and anodized BDD electrodes using cyclic voltammetry. The anodized BDD electrode exhibited well-defined irreversible cyclic voltammograms for the oxidation of tetracycline antibiotics with the highest current signals compared to the as-deposited BDD and glassy carbon electrodes. Low detection limit of 10 nM (signal-to-noise RATIO = 3) was achieved for each drug when using flow injection analysis with amperometric detection at anodized BDD electrodes. Linear calibrations were obtained from 0.1 to 50 mM for tetracycline and 0.5–50 mM for chlortetracycline, oxytetracycline and doxycycline. The proposed method has been successfully applied to determine the tetracycline antibiotics in some drug formulations. The results obtained in percent found (99.50–103.01%) were comparable to dose labeled.     

Development of an Enzymeless/Mediatorless Glucose Sensor Using Ruthenium Oxide‐Prussian Blue Combinative Analogue

Presented in this work is the first step towards an enzymeless/mediatorless glucose sensor. We first observed remarkable electrocatalytic oxidation of glucose using combinative ruthenium oxide (RuOx)‐Prussian blue (PB) analogues (designated as mvRuOx‐RuCN, mv: mixed valent) at ca. 1.1 V (vs. Ag/AgCl) in acidic media (pH 2 Na₂SO₄/H₂SO₄). Individual RuOx and PB analogs failed to give any such catalytic response. A high ruthenium oxidation state (i.e., oxy/hydroxy‐Ru^VII, E°≈1.4 V vs. RHE), normally occurring in strong alkaline conditions at RuOx‐based electrodes, was electrogenerated and stabilized (without any conventional disproportionation reaction) in the mvRuOx‐RuCN matrix for glucose catalysis. Detail X‐ray photoelectron spectroscopic studies can fully support the observation. The catalyst was chemically modified onto a disposable screen‐printed carbon electrode and employed for the amperometric detection of glucose via flow injection analysis (FIA). This system has a linear detection range of 0.3–20 mM with a detection limit and sensitivity of 40 μM (S/N=3) and 6.2 μA/(mM cm²), respectively, for glucose. Further steps towards the elimination of interference and the extendibility to neutral pHs were addressed.     

Development of a tubular fluoride potentiometric detector for flow analysis: evaluation and analytical applications

In this work a construction procedure for tubular fluoride electrode to be used in flow systems is outlined. The electrode was constructed from a commercially available, LaF₃ single crystal. Principal advantages of the flow detector presented include simplicity of construction, robustness, durability, low cost and easy coupling into any point of a flow manifold.Evaluation of the intrinsic working characteristics of the potentiometric detector in a low dispersion manifold is presented with respect to analytical and dynamic parameters. The constructed detector has similar working characteristics to those of the conventional fluoride electrodes, namely the detection limit, lower limit of linear response and operational pH range.The analytical usefulness of the constructed device was assessed in a flow system developed for fluoride determination in toothpaste, tablet, collutory and water samples for which the reference procedures suggest the determination of fluoride ion with a conventional ion selective electrode.     

Development of a flow injection method for monitoring cell membrane damage of wine lactic acid bacteria

A flow injection analysis (FIA) system was developed for the determination of phosphate efflux from wine lactic acid bacteria (Oenococus oeni and Lactobacillus hilgardii) as an indication of cell membrane damage. The system allowed the direct injection of the cell suspension, avoiding the filtration step, with minimum sample treatment and minimized reagent consumption. The developed system is characterized by a linear concentration zone between 3.23 × 10⁻⁵ and 4.84 × 10⁻⁴ mol L⁻¹ PO₄ ³⁻ and repeatability better than 2.9%. Bacterial suspensions were exposed to a chemical stress with phenolic acids and injected in the FIA system at regular intervals. The extracellular concentration of phosphate was measured spectrophotometrically. The experimental results obtained indicate that hydroxycinnamic acids (p-coumaric, ferulic and caffeic) induced faster phosphate leakage rates than hydroxybenzoic acids (vanillic and p-hydroxybenzoic) in both strains tested, which could be related to their higher lipophilic character.     

Reverse flow injection spectrophotometric determination of iron(III) using chlortetracycline reagent

A simple reversed flow injection colourimetric procedure for determining iron(III) was proposed. It is based on the reaction between iron(III) with chlortetracycline, resulting in an intense yellow complex with a suitable absorption at 435 nm. A 200 μl chlortetracycline reagent solution was injected into the phosphate buffer stream (flow rate 2.0 ml min⁻¹) which was then merged with iron(III) standard or sample in dilute nitric acid stream (flow rate 1.5 ml min⁻¹). Optimum conditions for determining iron(III) were investigated by univariate method. Under the optimum conditions, a linear calibration graph was obtained over the range 0.5–20.0 μg ml⁻¹. The detection limit (3σ) and the quantification limit (10σ) were 0.10 and 0.82 μg ml⁻¹, respectively. The relatives standard deviation of the proposed method calculated from 12 replicate injections of 2.0 and 10.0 μg ml⁻¹ iron(III) were 0.43 and 0.59%, respectively. The sample throughput was 60 h⁻¹. The proposed method has been satisfactorily applied to the determination of iron(III) in natural waters.     

鲁米诺-铁氰化钾流动注射化学发光法测定头孢拉定

在碱性介质中,铁氰化钾氧化鲁米诺产生化学发光,头孢拉定对该体系有显著的增强作用。基于此并结合流动注射技术建立了测定头孢拉定含量的化学发光新方法。该法线性范围为0.16~160 mg/L,检出限为0.028 mg/L;对80 mg/L的头孢拉定进行平行测定11次,其相对标准偏差为0.99%。用本法对胶囊中头孢拉定进行测定,并初步探讨了该化学发光的反应机理。