Letter: A simple ion source set-up for desorption/ionization on silicon with ion mobility spectrometry and ion mobility spectrometry-mass spectrometry

Using a simple ion source set-up, laser desorption/ionization on silicon (DIOS) was demonstrated with the use of a custom-made drift tube ion mobility spectrometer (IMS), mounted on a commercial triple quadrupole mass spectrometer, and with an IMS equipped with a Faraday plate detector. DIOS was tested by mobility measurement of tetrapropylammonium iodide, tetrabutylammonium iodide and tetrapentylammonium iodide, whilst 2,6-di-tert- butylpyridine was used as a standard. The reduced mobilities measured for the test halides are in concordance with previously obtained ion mobility spectrometry-mass spectrometry data.     

Separation of benzodiazepines by electrospray ionization ion mobility spectrometry-mass spectrometry

Benzodiazepines are a commonly abused class of drugs; requiring analytical techniques that can separate and detect the drugs in a rapid time period. In this paper, the two-dimensional separation of five benzodiazepines was shown by electrospray ionization (ESI) ion mobility spectrometry (IMS)-mass spectrometry (MS). In this study, both the two dimensions of separation (m/z and mobility) and the high resolution of our IMS instrument enabled confident identification of each of the five benzodiazepines studied. This was a significant improvement over previous IMS studies that could not separate many of the analytes due to low instrumental resolution. The benzodiazepines that contain a hydroxyl group in their molecular structure (lorazepam and oxazepam) were found to form both the protonated molecular ion and dehydration product as predominant ions. Experiments to isolate the parametric reasons for the dehydration ion formation showed that it was not the result of corona discharge processes or the potential applied to the needle. However, the potential difference between the needle and first drift ring did influence both the relative intensity ratios of the two ions and the ion sensitivity.     

Compensation voltage shifting in high-field asymmetric waveform ion mobility spectrometry-mass spectrometry

The separation and ion focusing properties of High-Field Asymmetric Waveform Ion Mobility Spectrometry (FAIMS) depend on desolvated ions entering the device, leading to a compound-specific, reproducible compensation voltage (CV) for each ion. This study shows that the conditions identified for stable spray and satisfactory ion desolvation in normal electrospray ionization mass spectrometry (ESI-MS) operation might significantly differ from those required for FAIMS-MS. In a typical setup with high-flow electrospray conditions, ions could be incompletely desolvated, resulting in the formation of unidentified clusters with differing behavior in a FAIMS environment. This causes compound-specific shifts of as much as 10 V in CV values when the mobile phase composition and/or flow rate are varied. The shifts diminish and finally disappear when the flow rate of methanol, used as mobile phase, is reduced to 40 microL/min and that of acetonitrile to 20 microL/min. The reproducibility of the observed CV was determined by scanning the CV while infusing a five-component mixture into a 400 microL/min flow of methanol or 50:50 acetonitrile/water. The relative standard deviation (RSD) for these multiple scans ranged from 0.7% to 6%. Therefore, under a constant set of experimental parameters, the CV does not shift appreciably. These observations have an impact on method development strategies. High flow rates can be used with the FAIMS device, since the CV values are reproducible, but it is likely that clusters are forming. Therefore, CV scans should be performed under conditions which mimic the chromatographic elution or flow injection analysis conditions, including matrix composition, to minimize errors in CV determination. An alternative approach is to determine the liquid flow rate at which the CV becomes compound-specific and to split the mobile phase stream accordingly. These experimental results may be specific to the setup used for this study and may not be directly applicable to other instrument FAIMS devices.     

The potential for clinical applications using a new ionization method combined with ion mobility spectrometry-mass spectrometry

Recently discovered ionization methods for use in mass spectrometry (MS), are widely applicable to biological materials, robust, and easy to automate. Among these, matrix assisted ionization vacuum (MAIV) is astonishing in that ionization of low and high-mass compounds are converted to gas-phase ions with charge states similar to electrospray ionization simply by exposing a matrix:analyte mixture to the vacuum of a mass spectrometer. Using the matrix compound, 3-nitrobenzonitrile, abundant ions are produced at room temperature without the need of high voltage or a laser. Here we discuss chemical analyses advances using MAIV combined with ion mobility spectrometry (IMS) real time separation, high resolution MS, and mass selected and non-mass selected MS/MS providing rapid analyte characterization. Drugs, their metabolites, lipids, peptides, and proteins can be ionized simultaneously from a variety of different biological matrixes such as urine, plasma, whole blood, and tissue. These complex mixtures are best characterized using a separation step, which is obtained nearly instantaneously with IMS, and together with direct ionization and MS or MS/MS provides a fast analysis method that has considerable potential for non-targeted clinical analyses.     

Separation of different ion structures in atmospheric pressure photoionization-ion mobility spectrometry-mass spectrometry (APPI-IMS-MS)

This study demonstrates how positive ion atmospheric pressure photoionization-ion mobility spectrometry-mass spectrometry (APPI-IMS-MS) can be used to produce different ionic forms of an analy te and how these can be separated. When hexane:toluene (9:1) is used as a solvent, 2,6-di-tert-butylpyridine (2,6-DtBPyr) and 2,6-di-tert-4-methylpyridine (2,6-DtB-4-MPyr) efficiently produce radical cations [M]⁺ and protonated [M + H]⁺ molecules, whereas, when the sample solvent is hexane, protonated molecules are mainly formed. Interestingly, radical cations drift slower in the drift tube than the protonated molecules. It was observed that an oxygen adduct ion, [M + O₂]⁺, which was clearly seen in the mass spectra for hexane:toluene (9:1) solutions, shares the same mobility with radical cations, [M]⁺. Therefore, the observed mobility order is most likely explained by oxygen adduct formation, i.e., the radical cation forrning a heavier adduct. For pyridine and 2-tert-butylpyridine, only protonated molecules could be efficiently formed in the conditions used. For 1- and 2-naphthol it was observed that in hexane the protonated molecule typically had a higher intensity than the radical cation, whereas in hexane:toluene (9:1) the radical cation [M]⁺ typically had a higher intensity than the protonated molecule [M + H]⁺. Interestingly, the latter drifts slower than the radical cation [M]⁺, which is the opposite of the drift pattern seen for 2,6-DtBPyr and 2,6-DtB-4-MPyr.     

Separation of leucine and isoleucine by electrospray ionization-high field asymmetric waveform ion mobility spectrometry-mass spectrometry

An electrospray ionization (ESI) source was used to generate gas-phase molecular anions of the amino acids leucine and isoleucine ((M–H)⁻; m/z −130), which were separated by high- field asymmetric waveform ion mobility spectrometry (FAIMS) and detected by quadrupole mass spectrometry (MS). This combination of ESI-FAIMS-MS enabled selective determination of either amino acid in mixtures that contained at least a 625-fold excess of the other. Comparisons with conventional ESI-MS showed a 50-fold improvement in the signal to background ratio for a 1 μM solution of leucine.     

An alternative field switching ion gate for ESI-ion mobility spectrometry

In electrospray ionization (ESI)-ion mobility spectrometry, continuously generated ions must be desolvated in a first tube before short ion pulses are introduced into a second (drift) tube. Both tubes are separated by an ion-gate. The resolving power of the resulting drift time spectrum is strongly influenced by the design of the ion gate. In the case of the Bradbury-Nielsen gates typically used, an orthogonal field between oppositely charged, parallel wires blocks ions from entering the drift tube. However, the blocking field also distorts the entering ion cloud. One alternative, which eliminates these effects and therefore enables a potentially higher resolving power, is already known for spectrometers with small ionization volumes, where ions are formed between two electrodes and subsequently transferred into the drift tube by a high voltage pulse. Based on this setup, we introduce an alternative ion gate design for liquid samples, named field switching ion gate (FSIG). The continuous flow of ions generated by ESI is desolvated in the first tube and introduced into the space between two electrodes (repeller and transfer electrodes). A third (blocking) electrode prevents the movement of ions into the drift tube in the closed state. Ions are transferred during the open state by pulsing the voltages of the repeller and blocking electrodes. First results demonstrate an increase of the resolving power by 100% without intensity losses and further changes in the spectrometer setup. The parameters of the FSIG, such as electrode voltages and pulse width, are characterized allowing the optimization of the spectrometer’s resolving power.     

High field asymmetric waveform ion mobility spectrometry-mass spectrometry: an investigation of leucine enkephalin ions produced by electrospray ionization

High field asymmetric waveform ion mobility spectrometry (FAIMS) provides atmospheric pressure, room temperature, low-resolution separation of gas-phase ions. The FAIMS analyzer acts as an ion filter that can continuously transmit one type of ion, independent of m/z. The combination of FAIMS with electrospray ionization and mass spectrometry (ESI-FAIMS-MS) is a powerful technique and is used in this study to investigate the cluster ions of leucine enkephalin (YGGFL). Separation by FAIMS of leucine enkephalin ions having the same m/z (m/z 556.5), [M + H]⁺ and [2M + 2H]²⁺, was observed. In addition, four complex ions of leucine enkephalin, [2M + H]⁺, [4M + 2H]²⁺, [6M + 3H]³⁺, and [8M + 4H]⁴⁺, all having m/z 1112, were shown to be separated in FAIMS. Fragmentation of ions as the result of harsh conditions within the mass spectrometer interface (FAIMS-MS) was shown to provide similar information to that obtained from MS/MS experiments in conventional ESI-MS.     

Rapid analysis of isomeric exogenous metabolites by differential mobility spectrometry-mass spectrometry

The direct separation of isomeric glucuronide metabolites from propranolol dosed tissue extracts by differential mobility spectrometry-mass spectrometry (DMS-MS) with the use of the polar gas-phase chemical modifier acetonitrile was demonstrated. The DMS gas-phase separation was able to resolve the isomeric metabolites with separation times on the order of milliseconds instead of minutes which is typically required when using pre-ionization chromatographic separation methods. Direct separation of isomeric metabolites from the complex tissue extract was confirmed by implementing a high-performance liquid chromatography (HPLC) separation prior to the DMS-MS analysis to pre-separate the species of interest. The ability to separate isomeric exogenous metabolites directly from a complex tissue extract is expected to facilitate the drug development process by increasing analytical throughput without the requirement for pre-ionization cleanup or separation strategies.     

Determination of terpenes in humid ambient air using ultraviolet ion mobility spectrometry

Atmospheric humidity causes the major problem using ion mobility spectrometers (IMS) under ambient conditions. Significant changes of the spectra are decreasing sensitivity as well as selectivity. Therefore, the influence of humidity on the IMS signal was investigated in case of direct introduction of the analyte into the ionisation chamber and in case of pre-separation by help of a multi-capillary column (MCC). For direct analyte introduction, a significant decrease of the total number of ions in the range of 28-42% with increasing relative humidity was found. Simultaneously additional peaks in the spectra were formed, thus complicating the identification of the analytes. In case of pre-separation of the analyte, the spectra do not change with increasing relative humidity, due to the successive appearance of the analyte and the water molecules in the ionisation chamber. Detection limits were found in the range of 5 μg/m³ (about 1 ppbv) for selected terpenes and—with pre-separation—independent on relative humidity of the analyte. Without pre-separation, detection limits are in the same range for dry air as carrier gas but in the range of 200-600 μg/m³ when relative humidity reaches 100%. Thus, MCC-UV ion mobility spectrometry is optimally capable for the detection of trace substances in ambient air (e.g. indoor air quality control, process control, odour detection) without further elaborate treatment of the carrier gas containing the analyte and independent on relative humidity.     

Chemical standards for ion mobility spectrometry: a review

Ion mobility spectrometry (IMS), using stand-alone instrumentation and hyphenated with mass spectrometry (IM-MS), has recently undergone significant expansion in the numbers of users and applications, particularly in sectors outside its established user base; predominantly military and security applications. Although several IMS reference standards have been proposed, there are no currently universally recognised reference standards for the calibration and evaluation of mobility spectrometers. This review describes current practices and the literature on chemical standards for validating IMS systems in positive and negative ion modes. The key qualities and requirements an ‘ideal’ reference standard must possess are defined, together with the instrumental and environmental factors such as temperature, electric field, humidity and drift gas composition that may need to be considered. Important challenges that have yet to be resolved are also identified and proposals for future development presented.     

Chemical standards in ion mobility spectrometry

Positive ion mobility spectra for three compounds (2,4-dimethylpyridine (2,4-DMP, commonly called 2,4-lutidine), dimethyl methylphosphonate (DMMP) and 2,6-di-t-butyl pyridine (2,6-DtBP)) have been studied in air at ambient pressure over the temperature range 37-250 °C with (H₂O)_nH⁺ as the reactant ion. All three compounds yield a protonated molecule but only 2,4-dimethylpyridine and dimethyl methylphosphonate produced proton-bound dimers. The reduced mobilities (K₀) of protonated molecules for 2,4-dimethylpyridine and DMMP increase significantly with increasing temperature over the whole temperature range indicating changes in ion composition or interactions; however, K₀ for the protonated molecule of 2,6-di-t-butyl pyridine was almost invariant with temperature. The K₀ values for the proton-bound dimers of 2,4-dimethylpyridine and DMMP also showed little dependence on temperature, but could be obtained only over an experimentally smaller and lower temperature range and at elevated concentrations. Chemical standards will be helpful as mobility spectra from laboratories worldwide are compared with increased precision and 2,6-di-t-butyl pyridine may be a suitable compound for use in standardizing reduced mobilities. The effect of thermal expansion of the drift tube length on the calculation of reduced mobilities is emphasized.     

Micro-plasma: a novel ionisation source for ion mobility spectrometry

Ion mobility spectrometry is an analytical method for identification and quantification of gas-phase analytes in the ppb_v-ppt_v range. Traditional ionisation methods suffer from low sensitivity (UV light), lack of long-term stability (partial discharge), or legal restrictions when radioactive sources are used. A miniaturised helium plasma was applied as ionisation source in an ion mobility spectrometer (IMS). Experiments were carried out to compare plasma IMS with β-radiation IMS. It could be demonstrated that the plasma IMS is characterised by higher sensitivity and selectivity than β-radiation ionisation. Plasma IMS is approximately 100 times more sensitive than the β-radiation IMS. Furthermore, variable sensitivity can be achieved by variation of the helium flow and the electric field of the plasma, and variable selectivity can be achieved by changing the electric field of the IMS. The experimental arrangement, optimisation of relevant conditions, and a typical application are presented in detail. Figure Micro-plasma used in ion mobility spectrometry     

Time-of-flight ion mobility spectrometry and differential mobility spectrometry: A comparative study of their efficiency in the analysis of halogenated compounds

The ion mobilities of halogenated aromatics which are of interest in environmental chemistry and process monitoring were characterized with field-deployable ion mobility spectrometers and differential mobility spectrometers. The dependence of mobility of gas-phase ions formed by atmospheric-pressure photoionization (APPI) on the electric field was determined for a number of structural isomers. The structure of the product ions formed was identified by investigations using the coupling of ion mobility spectrometry with mass spectrometry (APPI-IMS-MS) and APPI-MS. In contrast to conventional time-of-flight ion mobility spectrometry (IMS) with constant linear voltage gradients in drift tubes, differential mobility spectrometry (DMS) employs the field dependence of ion mobility. Depending on the position of substituents, differences in field dependence were established for the isomeric compounds in contrast to conventional IMS in which comparable reduced mobility values were detected for the isomers investigated. These findings permit the differentiation between most of the investigated isomeric aromatics with a different constitution using DMS.     

Real-time monitoring traces of SF6 in near-source ambient air by ion mobility spectrometry

The leakage of sulphur hexafluoride (SF₆) gas threats the global climate changes and personnel safety. Monitoring the concentration of SF₆ in its application places is an industry regulation. In this study, ion mobility spectrometry (IMS) was developed for fast monitoring traces of SF₆ in near-source ambient air. Due to the water is an important part of the natural air and affects most atmospheric measurements, the operating parameters of IMS monitoring SF₆ were optimised for quantitative analysis of SF₆ at different relative humidity (RH). It is discovered two main product ions SF₆^? and SOF₄^? by IMS at different RH. The calibration curves of SF₆ were investigated by its relationship with the peak intensity of SOF₄^– for real application. The time resolution of the measurement was obtained less than 1 s and the limit of detection (LOD) achieved 0.16–0.68 ppm with a data averaging of 30 times. At last, the simulated application of monitoring SF₆ leakage was tested in the fume hood of our lab. The results showed a great potential application prospect of IMS in monitoring SF₆ in the ambient air of its application places.     

High-field asymmetric waveform ion mobility spectrometry: a new tool for mass spectrometry

High-field asymmetric waveform ion mobility spectrometry (FAIMS) is a new technology for ion separation at atmospheric pressure. This review introduces the reader to FAIMS, covering topics ranging from the fundamentals and extraction of physical parameters from the raw data, to applications of FAIMS extending from homeland security to environmental analysis to proteomics. The investigation of FAIMS as an ion pre-processing tool for mass spectrometry is in its infancy, but reports in the literature illustrate that FAIMS separates isobaric ions including diastereoisomers, separates isotopes, reduces background ions by isolating ions of interest, and simplifies spectra of complex mixtures by dividing the mixture into a series of simpler subsets of ions. Applications ranging from quantitative analysis of inorganic and organometallic compounds, to studies of the conformers of intact proteins, have been reported. This review is a launching point for further exploration of FAIMS.     

Kinetic study of proton-bound dimer formation using ion mobility spectrometry

A method to measure the rate constant for the formation of symmetrical proton-bound dimers at ambient pressure was proposed. The sample is continuously delivered to the drift region of an ion mobility spectrometer where it reacts with a swarm of monomer ions injected by the shutter grid. Dimer ions are formed in the drift tube and a tail appears in the ion mobility spectrum. The rate constant is derived from the mobility spectra. The proposed approach was typically examined for methyl isobutyl ketone (MIBK), 2,4-dimethyl pyridine (DMP), and dimethyl methyl phosphonate (DMMP). The rate constants measured in this study were: 0.25 × 10⁻⁹, 0.86 × 10⁻¹⁰, and 0.47 × 10⁻¹⁰ cm³ s⁻¹ for MIBK, DMP and DMMP, respectively. The logarithm of the measured rate constants were found to be almost independent of reciprocal temperature within 303 to 343 K, indicating that no activation energy is involved in the formation of proton-bound dimers.     

Evaluation of micro-electrospray ionization with ion mobility spectrometry/mass spectrometry

In recent years, the resolving power of ion mobility instruments has been increased significantly, enabling ion mobility spectrometry (IMS) to be utilized as an analytical separation technique for complex mixtures. In theory, decreasing the drift tube temperature results in increased resolution due to decreased ion diffusion. However, the heat requirements for complete ion desolvation with electrospray ionization (ESI) have limited the reduction of temperatures in atmospheric pressure ion mobility instruments. Micro-electrospray conditions were investigated in this study to enable more efficient droplet formation and ionization with the objective of reducing drift tube temperatures and increasing IMS resolution. For small molecules (peptides), the drift tube temperature was reduced to ambient temperature with good resolution by employing reduced capillary diameters and flow rates. By employing micro-spray conditions, experimental resolution values approaching theoretically predicted resolution were achieved over a wide temperature range (30 to 250 °C). The historical heat requirements of atmospheric pressure IMS due to ESI desolvation were eliminated due to the use of micro-spray conditions and the high-resolution IMS spectra of GLY-HIS-LYS was obtained at ambient temperature. The desolvation of proteins (cytochrome c) was found to achieve optimal resolution at temperatures greater than 125 °C. This is significantly improved from earlier IMS studies that required drift tube temperatures of 250°C for protein desolvation.     

Evaporation of ionic liquids at atmospheric pressure: study by ion mobility spectrometry

A conventional ion mobility spectrometry (IMS) was used to study atmospheric pressure evaporation of seven pure imidazolium and pyrrolidinium ionic liquids (ILs) with [Tf₂N], [PF₆], [BF₄] and [fap] anions. The positive drift time spectra of the as-received samples measured at 220 °C exhibited close similarity; the peak at reduced mobility K₀ = 1.99 cm² V⁻¹ s⁻¹ was a dominant spectral pattern of imidazolium-based ILs. With an assumption that ILs vapor consists mainly of neutral ion pairs, which generate the parent cations in the reactant section of the detector, and using the reference data on the electrical mobility of ILs cations and clusters, this peak was attributed to the parent cation [emim]. Despite visible change in color of the majority of ILs after the heating at 220 °C for 5 h, essential distinctions between spectra of the as-received and heated samples were not observed. In negative mode, pronounced peaks were registered only for ILs with [fap] anion.     

Monte Carlo simulation of ion transport in ion mobility spectrometry

A program for simulation of ion trajectories in ion mobility spectrometry (IMS) instruments has been developed and incorporated into SIMION 7.0 [Int. J. Mass Spectrom. 200 (2000) 3–25]. Simulations were based on elastic collisions between ions and gas particles and conducted for an IMS drift tube. The program was validated by comparing the reduced mobility of helium ions derived from the simulation with the experimental data for helium ions in neon drift gas in low electric fields. Typical IMS parameters, including pressure, temperature, and flow rate of the drift gas were taken into account in the simulations. The program demonstrates capabilities of generating IMS spectra and predicting ion transport efficiency and separating ions. For the IMS drift tube studied, a correlation between imperfection of the electric field distribution and low resolution has been observed.