pH-effects in the complex formation of polymers I. Interaction of poly(acrylic acid) with poly(acrylamide)

The effects of polymer concentration, molecular weight of poly(acrylic acid) (PAA), addition of sodium, potassium, ammonium and copper (II) chlorides on the complex formation ability of the system PAA-poly(acrylamide) (PAAM) have been studied in aqueous solutions. The critical pH values of the complexation were determined in different conditions. The complex formation ability of PAAM is compared with other non-ionic polymers. It was shown that an increase in polymers concentration, molecular weight of PAA and ionic strength favours the complexation and shifts the critical pH values to the higher pH region. An addition of CuCl₂ to the mixture of two polymers enhances the complexation drastically due to the formation of triple complexes.     

Polyelectrolyte complexes of soluble poly-2-[(methacryloyloxy)ethyl]trimethylammonium chloride and its hydrogels with poly(acrylic acid)

The complex formation of poly-2-[(methacryloyloxy)-ethyl]trimethylammonium chloride (PMADQUAT) with poly(acrylic acid) (PAA) of different molecular weights has been studied in aqueous solutions by potentiometric, viscometric, turbidimetric and FTIR spectroscopic methods. The formation of insoluble non-stoichiometric polyelectrolyte complexes has been shown. The stability of polyelectrolyte complexes in solutions of different pH and ionic strength has been evaluated. The formation of polyelectrolyte complexes between hydrogels of PMADQUAT and linear PAA of different molecular weights has been studied. It was shown that the molecular weight of PAA considerably affects the kinetics of interaction as well as the final state of gel-polymer complex.     

Investigation of the microstructure of poly(diallyldimethyl-ammonium chloride) by nitrogen-14(15) NMR spectroscopy

CPMAS ¹³C and ¹⁵N solid-state NMR spectroscopy, as well as solution state ¹⁴N NMR spectroscopy, was used to investigate the microstructure of poly (diallyldimethylammonium chloride). The results of these studies, supported by ¹⁴N NMR studies of model compounds, were in agreement with the earlier conclusion of other workers (via solution state ¹³C NMR spectroscopy) that the polymer consists of a chain of five-membered pyrrolidinium rings, A. © 1994 John Wiley & Sons, Inc.     

New architectures of poly(ethylene glycol) and poly(methylthiirane) in block copolymers

Two synthetic ways were experimented to prepare new architectures of block copolymers made of poly(ethylene glycol) (PEG) and poly(methylthiirane). The coupling of both blocks conveniently end-capped as well as anionic polymerization of methylthiirane initiated by PEG-thiols gave readily the copolymers. Their characterization by ¹H NMR, SEC and IR confirmed the expected structures.     

Nanoparticles based on polyelectrolyte complexes: effect of structure and net charge on the sorption capability for solved organic molecules

 The sorption of solved organic molecules such as p-nitrophenol or dyes on previously formed nanoparticles based on polyelectrolyte/micelle complexes or polycation/polyanion complexes was studied. It could be shown that the sorption capability strongly depends on the structure and properties of the complex particles. Investigations have been made with complex particles that differ in their hydrophobic/hydrophilic structure, size and net charge. Such complex aggregates could be prepared by mixing the cationic surfactant dodecylamido-ethyldimethylbenzylammonium chloride, the polycations poly(diallyldimethylammonium chloride) or poly(methacryloyloxyethyldimethylbenzylammonium chloride) and the copolymers of maleic acid with propene or methylstyrene as anionic components. It is found that the sorption capability increases with increasing molar mass and hydrophobic properties of the components used. In addition, the concentration ratio c _polym/c _org.poll that was required to reach optimal sorption conditions could be decreased by the use of macromolecules with high molar masses. The best results were obtained by using cationic stabilized complex particles formed with high-molar-mass polycations as sorbents for anionic dye molecules. Received: 10 November 1999 Accepted: 24 February 2000     

Relationships between ringed spherulitic morphology and miscibility in blends of poly(ɛ-caprolactone) with poly(benzyl methacrylate) versus poly(phenyl methacrylate)

 Ringed spherulites are an interesting phenomenon that is observed only in very few miscible systems. For the first time, the relationship between the state of chain intermixing and the ring-band pattern was demonstrated. Two previously demonstrated miscible blend systems, poly(ɛ-caprolactone) (PCL) with poly(benzyl methacrylate) (PBzMA) and PCL with poly(phenyl methacrylate) (PPhMA), were studied in order to understand the mechanism of ring-band formation in the spherulites and the relationships between the ring-band pattern and the state of miscibility. In both miscible PCL/PBzMA and PCL/PPhMA systems, extinction rings were observed within the PCL spherulites. In the PCL/PBzMA blend, the extinction rings are not as distinct (owing to distortion) as those in the PCL/PPhMA blend system. Analysis was performed and discussions were made to reveal relationships between miscibility, interaction strength, and the pattern of the ring bands in the PCL spherulites in polymeric mixtures. Received: 5 January 2000/Accepted: 14 March 2000     

Photocurable biodegradable poly(ɛ-caprolactone)/poly(ethylene glycol) multiblock copolymers showing shape-memory properties

Biodegradable multiblock copolymers were synthesized by a polycondensation of poly(ɛ-caprolactone) (PCL) diols of molecular weight (MW)=3,000 and poly(ethylene glycol)s (PEG) of MW=3,000 with 4,4′-(adipoyldioxy)dicinnamic acid (CAC) dichloride as a chain extender in diphenyl ether at 180 °C for 2 h, and were characterized by GPC, ¹H-NMR, FTIR, UV, DSC, and WAXS. These photosensitive copolymers were irradiated by a 400-W high-pressure mercury lamp (λ>280 nm) from 5–60 min to form a network structure. The gel contents increased with irradiation time, and attained ca. 90% after 60 min for all copolymers. The degree of swelling in a distilled water at ambient temperature, and the rate of degradation in a phosphate buffer solution (pH 7.2) at 37 °C increased with increasing PEG components. The shape-memory tests were performed by a cyclic thermomechanical experiments for the photocured CAC/PCL/PEG (75/25) films. The film with a gel content of 57% showed the best shape-memory property with strain fixity rate of 100% and strain recovery rate of 88%.     

Crystallization behavior and biodegradation of poly(3-hydroxybutyrate) and poly(ethylene glycol) multiblock copolymers

Block copolymerization by using isocyanates is an effective method for incorporating PHB and PEG because it can prepare copolymers with good properties, such as toughness, strength, and so on. In this study, we adopted soil suspension system to estimate the biodegradability of a series of PHB/PEG multiblock copolymers with different compositions and block lengths. In the degradation process, the changes in weight loss, molecular weight, and tensile strength were periodically measured to determine the biodegradability, and the surface morphology was also observed by SEM. In contrast to pure PHB, the weight loss of the copolymer was relatively lower. On the other hand, the tensile strength and molecular weight experienced apparent decrease, and for BHG1000-3-1, they reached 46.7% and 77.7% of the initial value, respectively. SEM observation showed that the surface was covered with numerous erosion pits. All these indicate that the degradation indeed took place and long-chain molecules have been hydrolyzed into shorter ones. The crystallization behavior was also investigated by DSC and WAXD. The results showed that both the segments, PEG and PHB, can form crystalline phases at lower PHB contents ranging from 29% to 44%, and when PHB component was more than 60%, only PHB phase can crystallize.     

Novel poly(vinyl ether) block copolymers: Synthesis and colloidal stabilization of α-Fe2O3 in water and organic solvents

 Novel poly(vinyl-methylether)-b-poly(vinyloxy-4-butyric acid) diblock copolymers were made for the purpose of colloidal stabilization of particles in liquids. The synthesis via cationic polymerization with HI/I₂ initiation and the characterization of such novel diblock copolymers is described. A set of polymers was prepared including block copolymers with different block length ratios and the two separate homopolymers having the chemical composition of one of the blocks. Colloidal stabilization of α-Fe₂O₃ particles in water could be realized with all polymers except with the (vinylmethylether) homopolymer. One of the block copolymers was used for evaluation of the stabilizing abilities in organic solvents. Stable α-Fe₂O₃ dispersions could be prepared in solvents with very different polarities, ranging from methanol to toluene. In addition, it is shown that particles stabilized with these block copolymers can be easily transferred from water to an organic liquid. Received: 15 May 1997 Accepted: 13 October 1997     

Synthesis and properties of segmented block copolymers based on mixtures of poly(ethylene oxide) and poly(tetramethylene oxide) segments

The synthesis and characterisation of segmented block copolymers based on mixtures of hydrophilic poly(ethylene oxide) and hydrophobic poly(tetramethylene oxide) polyether segments and monodisperse crystallisable bisester tetra-amide segments are reported. The PEO length was varied from 600 to 8000 g/mol and the PTMO length was varied from 650 to 2900 g/mol. The influence of the polyether phase composition on the thermal mechanical and the elastic properties of the resulting copolymers was studied.The use of high melting monodisperse tetra-amide segments resulted in a fast and almost complete crystallisation of the rigid segment. The copolymers had only one polyether glass transition temperature, which suggests that the amorphous polyether segments were homogenously mixed. Thermal analysis of the copolymers showed one polyether melting temperature that was lower than in the case of ideal co-crystallisation between the two polyether segments. However, at PEO or PTMO lengths larger than 2000 g/mol two polyether melting temperatures were observed. The copolymer with the best low temperature properties was based on a mixture of PEO and PTMO segments, both having a molecular weight of 1000 g/mol, at a weight ratio of 30/70.     

Influence of physical-chemical interactions on the thermal stability and surface properties of poly(vinyl chloride)-b-poly(hydroxypropyl acrylate)-b-poly(vinyl chloride) block copolymers

The synthesis of poly(vinyl chloride) (PVC) homopolymers and poly(vinyl chloride)-b-poly(hydroxypropyl acrylate)-b-poly(vinyl chloride) (PVC-b-PHPA-b-PVC) block copolymers via a single electron - degenerative transfer mediated living radical polymerisation was carried out on a pilot scale in industrial facilities. The thermal stability of the products was assessed conductimetrically. The block copolymers, that contained a low content of PHPA (below 12 wt.%), showed thermal stability that was approximately three times greater than that of conventional PVC. Inverse gas chromatography study of the copolymers surface showed that there was a decrease in the dispersive component and greater Lewis acidity and basicity constants were observed relative to those of PVC. The thermal stabilisation of PVC when in the presence of PHPA is explained by the interactions between its functional groups and the structures formed during the thermal degradation. The thermal stability and the surface properties of PVC-b-PHPA-b-PVC were strongly dependent on the molecular weight of the block copolymer. Lewis acid-base interaction parameters were determined and are interpreted as evidence of the PVC-b-PHPA-b-PVC compatibilising function in PVC-wood flour composites.     

Swelling of hydrophobically modified poly(acrylamide) and poly(acrylamide)-co-(acrylic acid) gels in surfactant solutions

A series of hydrophobically modified polyacrylamide and polyacrylamide-co-poly(acrylic acid) gels with systematically varying hydrophobicity were prepared by free-radical polymerization of acrylamide, n-alkylacrylamides (n = 10, 12, and 14), and acrylic acid. The swelling of these gels was examined in water and in both anionic and cationic surfactant solutions. It was found that the gels which incorporated acrylic acid showed extremely high swelling in water. Maximum swelling was observed in gels which incorporated 10 mol% acrylic acid. The swelling of these gels was much less in solutions of both anionic and cationic surfactants than in water. The gels which did not incorporate acrylic acid demonstrated little swelling in water, but showed increased swelling in both anionic and cationic surfactant solutions with increased hydrophobicity of the gel. Received: 1 February 1999 Accepted in revised form: 5 March 1999     

Characterization of cross-linked poly(N-isopropylmethacrylamide) microgel latexes

 This article reports the colloidal and physicochemical characterization of crosslinked poly (N-isopropylmethacrylamide) (poly[NIPMAM]) latexes. The latex particles were first characterized by determining the lowest critical solubility temperature by measuring the optical density variation as a function of temperature. In addition, the electrophoretic mobility behaviors of all latexes were examined as a function of pH and temperature. Finally, the colloidal stability was investigated by determining the critical coagulation concentration and the critical flocculation temperature, and the corresponding results were discussed by taking into account both the effect of salinity and temperature on the solvency of poly[NIPMAM]. Received: 25 March 1999 Accepted: 5 May 1999     

Association between benzalkonium chloride and a poly( acrylic acid) gel. Study by microfiltration and membrane dialysis

Interactions between benzalkonium chloride (BAK) and the respective polymers, and the related availability of BAK in the corresponding solution, were studied for aqueous preparations of hydroxyethylcellulose (HEC), polyvinyl alcohol (PVA) and crosslinked poly(acrylic acid) (PAA). The study was performed by means of a crossflow filtration process with an alumina membrane. In the presence of the PAA gel, the rejection rate of BAK is much higher than with HEC or PVA. These results can be explained by the association of the benzalkonium cation BAK⁺ with the negative carboxylate groups or the PAA. This effect, which was confirmed by dialysis experiments, leads to the trapping of BAK⁺ inside the polymer network and could be of interest in the reduction of the harmful effects of BAK observed in the treatment of eye diseases.     

Nanostructured poly(urethane)s and poly(urethane-urea)s from reactive solutions of poly[styrene-b-butadiene-b-(methyl methacrylate)]-triblock copolymers

Poly[Styrene-b-Butadiene-b-(Methyl Methacrylate)], SBM triblock copolymers have been incorporated in different polyurethane, PU formulations in order to prepare nanostructured materials. Macrodiols used for PU synthesis were based on a central bis-phenol A, BPA unit with two hydroxyl-terminated oligo(oxypropylene), BPA-PO_x or oligo(oxyethylene), BPA-EO chains with varying lengths. The initial solubility of the three blocks and the rheological behavior of the solutions in macrodiols and also in two diisocyanates, isophorone diisocyanate, IPDI, and 1,3-xylylene diisocyanate, XDI have been first characterized. The PMMA block is the most soluble and its role during the reaction is to stabilize the initial nanostructure or to control the reaction-induced microphase separation.Block copolymers can be dissolved first in the macrodiol, or preferably in the diisocyanate. With BPA-PO_x and low SBM content (<10 wt%), transparent linear or crosslinked PU with well dispersed triblock nanoparticles have been prepared, depending on the molar mass of the macrodiol and on the concentration of diblock SB impurities present in the triblock. For high SBM concentrations (>50 wt%), a twin screw extruder had to be used for the blending. Under well-defined conditions, transparent linear PUs and linear segmented polyurethane-ureas have been prepared.This study confirms that for designing a nanostructured material from a reactive mixture with a triblock additive, one block, called “the nanostructuring block” has to remain soluble up to the end of the reaction.     

New poly(amide-imide) siloxane copolymers by polycondensation

Some new poly(amide-imide) siloxane copolymers have been synthesized by solution polycondensation of some aromatic diamines with siloxanic diacids having preformed imide rings. Two polycondensation techniques were used: polycondensation of aromatic diamines with diacid chlorides and direct polycondensation of aromatic diamines with diacids in the presence of organic phosphites, following the Yamazaki-Higashi phosphorylation technique. In all cases the reactions were carried out using equimolecular amounts of the two monomers, in polar aprotic solvents and inert atmosphere.The obtained compounds were characterized by elemental C, H and Si analysis, solubility tests, IR and ¹H-NMR spectrometry. Thermogravimetric curves were also recorded. All data agree with the proposed structures.     

Environmental stress cracking of poly(vinyl chloride) in alkaline solutions

The environmental stress cracking (ESC) effects on PVC of various high pH sodium hydroxide environments have been studied. The behaviour of PVC specimens in air and pH 12, 13, 13.5 and 14.39 sodium hydroxide solutions has been examined under three-point bend, tensile and creep conditions. Two parameters were used in three-point bend testing to determine the effect of an applied strain and high pH environment on the stability of PVC, namely time to craze initiation and width of crazing. It was found that, in general, crazing occurred sooner and to a greater degree with increasing strain and pH, although there was some evidence that craze growth was most rapid at pH 13.5. The results also indicated a critical strain value of 1.5–1.6%, below which crazing was not observed in any of these alkaline environments. Creep and tensile testing revealed that the time for which a PVC specimen was immersed in the environment was very important in determining the severity of the environmental effect. Creep tests at elevated temperatures showed that the time for the effects to be manifest decreased with increasing temperature. Creep rates were highest in pH 13.5 sodium hydroxide solution indicating that this was the most hostile of the environments considered.     

The influence of core-shell structured modifiers on the toughness of poly (vinyl chloride)

The core-shell structured grafted copolymer particles of polybutadiene grafted polymethyl methacrylate (PB-g-PMMA, MB) were prepared by emulsion polymerization. The MB particles were used to modify poly (vinyl chloride) (PVC) by melt blending. The mechanical properties of the PVC blends were investigated. The micro-morphology of the PVC blends was observed by scanning electron microscopy (SEM). The results indicated that the samples with the best impact strength could be obtained when the core-shell weight ratio of PB to PMMA is lower than 93:7, the mechanical properties correlated well with SEM morphologies, the addition of modifier with the ratio core to shell of 93:7 could reduce the domain size of the dispersed phase. Furthermore, the compatibility and properties of the blends were greatly enhanced and improved. The modifier particles could be well dispersed in the PVC matrix.     

Interpolymer complexes of copolymers of vinyl ether of diethylene glycol with poly(acrylic acid)

 The complex formation reactions of poly(vinyl ether of diethylene glycol) as well as vinyl ether of diethylene glycol–vinyl butyl ether copolymers with poly(acrylic acid) have been studied in aqueous and alcohol solutions. The formation of interpolymer complexes which were stabilized by hydrogen bonds was shown. The effects of molecular weight of poly(acrylic acid) and the nature of the nonionic polymer on the composition and stability of interpolymer complexes were clarified. The critical pH values of complexation were determined for different systems with various molecular weights and hydrophobic–hydrophilic balances. The stability of the interpolymer complexes formed in aqueous and alcohol solutions with respect to dimethylformamide addition was evaluated. The role of hydrophobic interactions and the presence of active groups on stability of the interpolymer complexes is discussed. Received: 23 July 2001 Accepted: 27 September 2001     

Small-angle neutron scattering study of poly(methyl methacrylate-block-sodium acrylate-block-methyl methacrylate) and poly(sodium acrylate-block-methyl methacrylate-block-sodium acrylate) triblock copolymers in aqueous solutions

 Small-angle neutron scattering experiments were made on poly(methyl methacrylate-block-sodium acrylate-block-methyl methacrylate) [p(MMA-b-NaA-b-MMA)] and p(NaA-b-MMA-b-NaA) solutions by varying the composition and the concentration of the polymer with and without 1 M NaCl added. Scattering curves could be evaluated by assuming that the polymers aggregate into polydisperse micelles. The experiments support the expectation that in the case of the p(MMA-b-NaA-b-MMA) block sequence the hydrophilic blocks form closed loops connected by both ends to the micellar cores; in the case of the p(NaA-b-MMA-b-NaA) block sequence they float freely in the solvent. The micellar cores exert considerable stability against dilution and added electrolyte. The interaction of charged micelles could be formally described in terms of volume exclusion and the Derjaguin–Landau–Verwey–Overbeek potential. Received: 20 December 2000 Accepted: 18 August 2001