Metallic single-walled carbon nanotubes for conductive nanocomposites

This article reports an unambiguous demonstration that bulk-separated metallic single-walled carbon nanotubes offer superior performance (consistently and substantially better than the as-produced nanotube sample) in conductive composites with poly(3-hexylthiophene) and also in transparent conductive coatings based on PEDOT:PSS. The results serve as a validation on the widely held view that the carbon nanotubes are competitive in various technologies currently dominated by conductive inorganic materials (such as indium tin oxide).     

Enhanced dewatering of polyelectrolyte nanocomposites by hydrophobic polyelectrolytes

We demonstrate that increasing the hydrophobic environment around the charge center of a polyelectrolyte (PE) not only decreases the water content of an adsorbed PE layer but can even dewater up to ~50% of an initially hydrated substrate. The results of this work are expected to yield new stratagies to dewater PE systems and have potential applications in mineral recovery, paper manufacturing, and biomedical materials. Adsorption of a series of cationically derivatized dextran polyelectrolytes onto sulfated nanocrystalline cellulose (SNC) has been studied using quartz crystal microbalance with dissipation monitoring (QCM-D) and surface plasmon resonance (SPR). Synthesized samples of (N,N-dimethylamino)ethyldextran (DMAE-Dex), (N,N-diethylamino)ethyldextran (DEAE-Dex), and (N,N-diisopropylamino)ethyldextran (DIAE-Dex) had degrees of substitution (DS) ranging from 0.05 to 0.82. DMAE-Dex, DEAE-Dex, and DIAE-Dex all showed decreasing adsorption onto SNC and decreasing water content of the adsorbed film with increasing DS. Additionally, DEAE-Dex and DIAE-Dex films adsorbed onto SNC contained less water than DMAE-Dex films with the same DS. Interestingly, QCM-D results for high DS DIAE-Dex adsorbed onto SNC revealed mass loss, whereas SPR results clearly showed DIAE-Dex adsorbed. These observations were consistent with dehydration of the SNC substrate. This study indicates that the water content of the substrate could be tailored by controlling the DS and hydrophobic character of the adsorbed polyelectrolytes.     

Layer-by-layer-assembled microfiltration membranes for biomolecule immobilization and enzymatic catalysis

Multilayer assemblies of polyelectrolytes, for protein immobilization, have been created within the membrane pore domain. This approach was taken for two reasons: (1) the high internal membrane area can potentially increase the amount of immobilized protein, and (2) the use of convective flow allows uniform assembly of layers and eliminates diffusional limitations after immobilization. To build a stable assembly, the first polyelectrolyte layer was covalently attached to the membrane surface and inside the pore walls. Either poly(L-glutamic acid) (PLGA) or poly(L-lysine) (PLL) was used in this step. Subsequent deposition occurs by multiple electrostatic interactions between the adsorbing polyelectrolyte [poly(allylamine) hydrochloride (PAH) or poly(styrenesulfonate) (PSS)] and the oppositely charged layer. Three-layer membranes were created: PLL-PSS-PAH or PLGA-PAH-PSS, for an overall positive or negative charge, respectively. The overall charge on both the protein and membrane plays a substantial role in immobilization. When the protein and the membrane are oppositely charged, the amount immobilized and the stability within the polyelectrolyte assembly are significantly higher than for the case when both have similar charges. After protein incorporation in the multilayer assembly, the active site accessibility was comparable to that obtained in the homogeneous phase. This was tested by affinity interaction (avidin-biotin) and by carrying out two reactions (catalyzed by glucose oxidase and alkaline phosphatase). Besides simplicity and versatility, the ease of enzyme regeneration constitutes an additional benefit of this approach.     

Enhancing enzymatic properties by the immobilization method

Effects of some immobilized carriers on enzymatic properties have been studied. The following results were obtained: (1) When cholinesterase was immobilized on the hydrophobic carrier with either α-naphthylamine, benzylamine, orp-methylbenzylamine groups, the affinities of immobilized cholinesterase for toxic organophosphors, GB (Isopnopy 1-methylphophonofluoridate) and Vx [o-ethyl-S-(2-diisopnoylomino-thyl) methyl phosphonothiolate], were enhanced 60–90 times and 700–1200 times, respectively, whereas the thermal stability of the immobilized cholinesterase increased to 110%. Approximately 82–88% activity of the immobilized cholinesterase remained after continuously operating for 8 h; and (2) Lipase was immobilized on the carrier that was made up of 6% polyethylenimine, 1% alginate gel, and 1% glutaraldehyde. The initial reaction rate of the esterification of lauric acid with lauric alcohol catalyzed by this kind of immobilized lipase was increased 21 times, as compared to lipase powder. About 72% esterification activity of lipase remained after continuous operating for 10 d.     

Facile synthesis of highly conductive polyaniline/graphite nanocomposites

A facile process for the synthesis of exfoliated graphite and polyaniline/graphite (PANI/graphite) nanocomposite was developed. Graphite nanosheets were prepared via the microwave irradiation and sonication from synthesized expandable graphite. The nanocomposites were fabricated via in situ polymerization of aniline monomer in the presence of graphite nanosheets. The nanoscale dispersion of graphite sheets was evidenced by the SEM and TEM examinations. According to the electrical conductivity test, the conductivity of the final PANI/graphite nanocomposites were dramatically increased compared with pristine PANI. From the thermogravimetric analysis, the introduction of graphite exhibits a beneficial effect on the thermal stability of PANI.     

Electrodeposition of layered manganese oxide nanocomposites intercalated with strong and weak polyelectrolytes

Multilayered manganese oxide nanocomposites intercalated with strong (poly(diallyldimethylammonium) chloride, PDDA) and weak (poly(allylamine hydrochloride), PAH) polyelectrolytes can be produced on polycrystalline platinum electrode in a thin film form by a simple, one-step electrochemical route. The process involves a potentiostatic oxidation of aqueous Mn2+ ions at around +1.0 V (vs Ag/AgCl) in the presence of polyelectrolytes. Fully charged PDDA polycations are accommodated tightly in the interlayer space by electrostatic interaction with negative charges on the manganese oxide layers, leading to an interlayer distance of 0.97 nm. The layered film prepared with PAH has a larger polymer content (PAH/Mn molar ratio of 0.98) than that (PDDA/Mn molar ratio of 0.43) made with PDDA because of the smaller charging degree of PAH, exhibiting a larger interlayer distance (1.19 nm). The interlayer PAH contains neutral (-NH2) and positively charged (-NH3(+)) amine groups, and the -NH3(+) groups are associated with Cl- (to generate -NH3(+) Cl- ion pairs) as well as the negatively charged manganese oxide layers. Both polyelectrolytes once incorporated were not ion exchanged with small cations in solution. The layered structure of PDDA/MnO(x) was collapsed during the reduction process in a KCl electrolyte solution, accompanying an expansion of the interlayer as a result of incorporation of K+ ions for charge neutrality. On the contrary, the layered PAH/MnO(x) film showed a good electrochemical response due to the redox reaction of Mn3+/Mn4+ couple with no change in the structure. X-ray photoelectron spectroscopy revealed that, in this case, excess negative charges generated on the manganese oxide layers upon reduction can be balanced by the protons being released from the -NH3(+) Cl- sites in the interlayer PAH; the Cl- anions becoming unnecessary are inevitably excluded from the interlayer, and vice versa upon oxidation.     

Preparation and properties of conductive silver/photosensitive polyimide nanocomposites

A new electrically conductive photoresist has been developed. It is based on the dispersion of silver nanoflakes in a negative‐tone photosensitive polyimide (PSPI) precursor. 2‐Mercaptopropionic acid was used as the surfactant to modify the silver nanoflake surface for the dispersion of silver nanoflakes in the polymer. The silver/PSPI nanocomposites showed electrical conductivity at a low silver content of 10 wt %. The electrical conductivity of the silver/PSPI nanocomposites ranged from 10 to 10⁴ S/cm, which was dependent on the silver weight fraction in the resist formulation. Patterns with a resolution of 30 μm were obtained from the silver/PSPI nanocomposites. The silver/PSPI nanocomposites had excellent thermal properties. Their glass transition temperatures were above 360 °C and thermal decomposition temperatures were over 420 °C. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 1575–1583, 2009     

Morphological and structural characterization of polypropylene/conductive graphite nanocomposites

The structure and morphology of polypropylene/conductive graphite (PP/CG) composites were studied by wide angle X-ray diffraction, small-angle X-ray scattering and scanning electron microscopy. An effect of graphite on the crystallization behavior was observed and the opposite influences of enhanced thermal conductivity and hinder of chain mobility on the formation of the γ-phase of PP were discussed.     

Enzyme immobilization on a pH-responsive porous polymer membrane for enzymatic kinetics study

Immobilization of enzymes onto carriers is a rapidly growing research area aimed at increasing the stability, reusability and enzymolysis efficiency of free enzymes. In this work, the role of phase-separation and a pH-responsive “hairy” brush, which greatly affected the topography of porous polymer membrane enzyme reactors (PMER), was explored. The porous polymer membrane was fabricated by phase-separation of poly(styrene-co-maleic anhydride-acrylic acid) and poly(styrene-ethylene glycol). Notably, the topography and pores size of the PMER could be controlled by phase-separation and a pH-responsive “hairy” brush. For evaluating the enzymolysis efficiency of d-amino acid oxidase (DAAO) immobilized carrier (DAAO@PMER), a chiral ligand exchange capillary electrophoresis method was developed with d-methionine as the substrate. The DAAO@PMER showed good reusability and stability after five continuous runs. Notably, comparing with free DAAO in solution, the DAAO@PMER exhibited a 17.7-folds increase in catalytic velocity, which was attributed to its tailorable topography and pH-responsive property. The poly(acrylic acid) moiety of poly(styrene-co-maleic anhydride-acrylic acid) as the pH-responsive “hairy” brush generated topography changing domains upon adjusting the buffer pH, which enable the enzymolysis efficiency of DAAO@PMER to be tuned based upon the well-defined architectures of the PMER. This approach demonstrated that the topographical changes formed by phase-separation and the pH-responsive “hairy” brush indeed made the proposed porous polymer membrane as suitable supports for enzyme immobilization and fitting for enzymolysis applications, achieving high catalytic performance.     

The use of surfactants for dispersing carbon nanotubes and graphene to make conductive nanocomposites

Applications of composites based on carbon nanotubes and graphene require their exfoliation and dispersion in a polymer matrix. One of the main approaches to disperse and exfoliate carbon nanotubes and graphene is based on the use of surfactants. Here we review the surfactants utilized for dispersing carbon nanotubes and graphene, the mechanisms of filler stabilization and the methods for composite preparation based on the use of surfactants to get conductive polymer composites with minimum nanofiller loading.     

Novel conductive nanocomposites from perfluoropolyether waterborne polyurethanes and carbon nanotubes

The exceptional electrical conductivity of carbon nanotubes (CNTs) has been exploited for the preparation of conductive nanocomposites based on a large variety of insulating polymers. Among these, perfluoropolyether‐polyurethanes (PFPE‐PUs) represent a class of highly performing fluorinated materials with excellent water/oil repellency, chemical resistance, and substrate adhesion. The incorporation of highly conductive fillers to this class of highly performing materials allows them to be exploited in new technological and industrial fields where their unique properties need to be combined with the electrical conductivity or the electrostatic dissipation properties of carbon nanotubes. However, no studies have been presented so far on nanocomposites based on PFPE‐PUs and CNTs. In this work, polymer nanocomposites based on waterborne PFPE‐PUs and increasing amounts of carboxylated multiwall CNTs (COOH‐CNTs) were prepared and characterized for the first time. The effect of increasing concentration of COOH‐CNTs on the physical, mechanical, and surface properties of the nanocomposites was investigated by means of rheological measurements, dynamic mechanical analysis, thermal characterization, optical contact angle measurements, and scanning electron microscopy. In addition, electrical measurements showed that the highly insulating undoped PFPE‐PU system undergoes substantial modifications upon addition of COOH‐CNTs, leading to the formation of conductive nanocomposites with electrical conductivities as high as 1 S/cm. The results of this study demonstrate that the addition of COOH‐CNTs to PFPE‐PU systems represents a promising strategy to expand their possible use to technological applications where chemical stability, water/oil repellence and electrical conductivity are simultaneously required. Copyright © 2014 John Wiley & Sons, Ltd.     

Straightforward synthesis of conductive graphene/polymer nanocomposites from graphite oxide

The reduction of graphite oxide (GO) in the presence of reactive poly(methyl methacrylate) (PMMA), under mild biphasic conditions, directly affords graphene grafted with PMMA. The resulting nanocomposite shows excellent electrical conductivities resulting from the optimal dispersion and exfoliation of graphene in the polymer matrix.     

Eco‐friendly conductive polymer nanocomposites (CPC) for solar absorbers design

To reduce both the cost and the environmental impact of copper‐based thermal solar absorbers, we have investigated their possible substitution by bio‐based conductive polymer nanocomposite (CPC) elements. Our results show that carbon nanotubes (CNT) have no significant influence on polymers’ calorimetric properties such as T_m and T_g but lead to a strong increase in crystallinity of poly(lactic acid) (PLA) and to a lesser extent of poly(amide 12) poly(amide 12) (PA12) for 2 and 3 CNT wt % respectively. Percolation thresholds as low as 0.5 and 0.58 were obtained for PA12 and PLA, respectively, and visco‐elastic properties such as η*, G’ and G” were found to increase exponentially with CNT content confirming the formation of a CNT network within the matrix. All CPC are absorbing more energy in the visible and infrared than in the ultraviolet wavelength ranges. Finally, the thermal conductivity k of PLA–CNT and PA12–CNT were increased, respectively, of 85% and 24%, to reach 0.28 W.m^?1.K^?1 and 0.26 W.m^?1.K^?1, for only 5 wt% CNT. The figure of merit suggests that PA12 is the polymer which satisfies at best all criteria, particularly combining a lower viscosity at almost equivalent thermal conductivity and absorptivity. Copyright © 2013 John Wiley & Sons, Ltd.     

Efficient photoreduction strategy for uranium immobilization based on graphite carbon nitride/activated carbon nanocomposites

Uranium removal from aqueous solutions using environmentally friendly photocatalytic technology is a novel approach for resource recovery. Herein, carbon nitride/activated carbon composite materials (CN/AC) were investigated for U(VI) reduction under visible light. An exceptional boost in photocatalytic activity was observed for CN/AC composites (up to 70 times over the conventional bulk g-C₃N₄). The strong interactive conjugated π-bond structure between g-C₃N₄ and AC accelerated the migration of carriers and then prolonged the electron lifetime. CN/AC composites exhibited excellent compatibility with different water substrates and were resilience to a wide range of pH changes and abundant competitive anions/cations. Quenching experiments and electron microscopy characterization indicated that U(VI) was reduced by photogenerated electrons and deposited on the edge of CN/AC composites. The low-cost, high-performance carbon-based composite material proposed in this work is a potential candidate for the efficient treatment of radioactive wastewater.     

Investigating the effect of ultrasonic irradiation on preparation and properties of conductive nanocomposites

In the present study, the ultrasonic irradiation technique was employed as a new approach to prepare 0-3-dimensional polyaniline/ZnO shell-core composite particles. By taking advantage of the multiple effects of ultrasound, one can break down the aggregates of nanocrystalline ZnO particles. The polymerization of aniline proceeded while the nanoparticles were redispersed by ultrasound, and the synthesized polyaniline deposited on the ZnO particle, which formed polyaniline-coated nanocrystalline composite particles. The material was characterized by using transmission electron microscopy, XRD, scanning electron microscopy (SEM), fourier transform infrared spectroscopy (FTIR), and Thermogravimetric analysis (TGA). With increased ZnO content, the H-bonding interaction is strengthened and the characteristic peaks of benzoid and quinoid are shifted. X-ray photoelectron spectroscopy (XPS) shows that the ratio of the number of Zn and N atoms (Zn/N) on the surface is lower than that in the bulk. This is strong evidence for a PANI-encapsulated ZnO nanoparticles structure. The conductivity of the composites obtained through ultrasonic irradiation decreases with increasing ZnO content. Ultrasonic irradiation contributes to the increase in the conductivity compared with conventional stirring. Photocatalytic properties of PANI/ZnO nanocomposites were examined by degrading Reactive Black 5 (RB5) dye under visible light irradiation.     

Functionalized graphene sheet—Poly(vinylidene fluoride) conductive nanocomposites

PVDF nanocomposites based on functionalized graphene sheets, FGS prepared from graphite oxide, and exfoliated graphite, EG, were prepared by solution processing and compression molding. FGS remains well dispersed in the PVDF composites as evidenced by the lack of the characteristic graphite reflection in the composites. Although the α‐phase of PVDF is seen in the EG‐based composites, a mixture of α‐ and β‐phases is present in the FGS analogs. SEM and TEM imaging show smooth fractured surfaces with oriented platelets of graphite stacks and obvious debonding from the matrix in the EG‐PVDF composites. In contrast, the FGS‐PVDF composites show a wrinkled topography of relatively thin graphene sheets bonded well to the matrix. Storage modulus of the composites was increased with FGS and EG concentration. A lower percolation threshold (2 wt %) was obtained for FGS‐PVDF composites compared to EG‐PVDF composites (above 5 wt %). Lastly, the FGS‐PVDF composites show an unusual resistance/temperature behavior. The resistance decreases with temperature, indicating an NTC behavior, whereas EG‐PVDF composites show a PTC behavior (e.g., the resistance increases with temperature). We attribute the NTC behavior of the FGS based composites to the higher aspect ratio of FGS which leads to contact resistance predominating over tunneling resistance. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 888–897, 2009     

A novel approach for highly proton conductive electrolyte membranes with improved methanol barrier properties: Layer-by-Layer assembly of salt containing polyelectrolytes

A series of highly proton conductive electrolyte membranes with improved methanol barrier properties are prepared from polyallylamine hydrochloride (PAH) and polystyrene sulfonic acid (PSS) including salt by Layer-by-Layer (LbL) method. The effects of added salt type (NaCl, MgCl₂) and salt concentration (1.0 M, 0.1 M) on proton conductivity (σ) and methanol barrier properties of the LbL self-assembled composite membranes are discussed in terms of controlled layer thickness and charge density. Furthermore, the influences of ion type in the multilayered composite membranes are studied in conjunction with physicochemical and thermal properties.The deposition of the self-assembly of PAH/PSS film on Nafion is followed by UV–Vis spectroscopy and it is observed that the polyelectrolyte layers growth on both sides of Nafion membrane regularly. (PAH/PSS)₅–Na⁺ and (PAH/PSS)₅–H⁺ with 1.0 M NaCl exhibits 49.6 and 27.8% reduction in lower methanol permittivity in comparison with the pristine Nafion^®117, respectively, while the proton conductivities are 12.97 and 74.69 mS cm⁻¹. Promisingly, it is found that the membrane selectivity values (Φ) of all multilayered membranes in H⁺ form are much higher than that of salt form (Na⁺ and Mg²⁺) and perfluorosulfonated ionomers reported in the literature. Also, we find out that the use of polyelectrolytes with high charge density causes a further improvement in proton conductivity and methanol barrier properties simultaneously. These encouraging results indicate that upon a suitable choice of LbL deposition conditions, composite membranes exhibiting both high proton conductivity and improved methanol barrier properties can be tailored for fuel cells.     

An experimental investigation on the conductive behavior of carbon nanotube-reinforced natural polymer nanocomposites

It is well known that carbon nanotubes (CNTs) have excellent electrical properties and can be used as the nanofiller in natural polymers to produce conductive CNT/polymer nanocomposites. In this study, the conductive behavior of CNT-reinforced natural polymer nanocomposites was investigated. The effect of CNT concentration on the conductivity of CNT/natural polymer nanocomposites was also investigated. The natural polymers used were plasticized starch (PS) and chitosan (CS). FTIR spectroscopy was used to examine the interactions between PS, CS, and CNTs. TEM analysis on both nanocomposites were made to study the dispersion states of CNTs in both polymers. The results showed that the surface resistivities of both CNT/PS and CNT/CS nanocomposites decreased steeply with increasing CNT concentration. Particularly, the CNT/CS nanocomposites showed a better conductivity than the CNT/PS composites at the same CNT concentration. The TEM result showed that CNT/CS nanocomposites had better dispersibility and formation of fully connected, three-dimensional network structures between the CNTs than the CNT/PS nanocomposites, which results in the superior conductive property of CNT/CS nanocomposites compared to the CNT/PS nanocomposites.