p—Si上电沉积Ni—W合金薄膜

利用恒电流沉积法，在ｐ－Ｓｉ上制备出不同Ｗ含量和不同结构的Ｎｉ－Ｗ薄膜，研究了镀液温度，ｐＨ值，电流密度对镀层组成的影响，结果表明，提高温度有利于获得高Ｗ含量的合金。     

蚀刻金属铝箔覆型制备Ni-P微阵列材料及析氢电催化性能研究

以蚀刻金属铝箔为模板,用化学镀制备了具有微米阵列结构的Ni-P合金材料,使用扫描电镜、能量散射谱及X-射线衍射等表征手段对所得材料的微观形貌与物质组成进行了分析,并通过电化学方法研究了化学镀温度、施镀时间对材料析氢催化活性的影响。结果表明,70℃制得的Ni-P微阵列材料作电极其析氢过电位最小,电流密度为15m A/cm2时比光面Ni-P镀层下降了约100m V;同时表现出最高的交换电流密度13.53×10-6A/cm2,高出光面Ni-P镀层近1个数量级;70℃施镀4h能够得到析氢过电位较低且结构完整的镀层,延长镀时没有继续提升其性能。为直观衡量材料的催化活性,在双室槽中进行了光解水析氢测试。Ni-P微阵列材料表现出良好的催化活性,析氢速率较光面电极上升约200%。     

Ni-P化学镀反应速率及机理研究

通过镀层分析和析氢量测量得到Ni-P镀层的沉积速度和H2PO2的分解速度·以混合电位理论为基础，对Ni－P电极在不同组成饮液中的极化曲线进行分解得到以化学镀电流形式所表示的反应速率·将两种方法所得结果进行对照，确定H2PO2氧化时电子迁移数为1，并用原子红-电化学联合理论解释溶液PH对反应速率及化学镀效率的景响．     

Fe-Ni-S软磁薄膜的电沉积

酸性镀液中以硼酸为缓冲剂、柠檬酸三钠为配合剂,在紫铜箔上电沉积得到非晶Fe-Ni-S合金薄膜。 采用扫描电子显微镜和能谱分析技术(EDS)研究了镀液组成和沉积条件对镀层表面形貌和组成的影响。 结果表明,在镀液中加入2 g/L C7H5O3NS（糖精）和0.4 g/L 1,4-丁炔二醇可获得表面平整无裂缝和较小内应力的合金镀层;电流密度和镀液pH值对镀层组成影响较小,但施镀温度对镀层组成影响较大。 获得了理想的镀液组成和沉积条件,所得Fe73Ni9.5S17.5薄膜的X射线衍射表明其为非晶结构,在室温下具有较高的饱和磁化强度(Ms约为876.25 kA/m)和较低的矫顽力(Hc约为4.96 kA/m),具有良好的软磁性能。 循环伏安曲线和阴极极化曲线均表明,镀液中CS(NH2)2会促进Fe-Ni-S共沉积。     

Co—WC电极

从钴镀液中添加ＷＣ微粒复合电沉积制备Ｃｏ－ＷＣ镀层，ＷＣ微粒的加入，加快了阴极电化学反应。Ｃｏ－ＷＣ复合电极在碱性溶液中具有优越的电催化析氢性能，并经受了长期间断电解的试验，电极性能稳定。     

主盐浓度和工艺条件对Sn-Ag-Cu合金镀层组成和形貌的影响

在弱酸性镀液中电沉积得到无铅Sn-Ag-Cu可焊性合金镀层。采用X射线荧光光谱仪(XRF)和扫描电子显微镜(SEM)研究了镀液中主盐浓度和电镀工艺条件对镀层的组成和形貌的影响。研究表明,Sn-Ag-Cu合金的电沉积是正则共沉积。镀液中Sn²⁺和Ag⁺浓度改变对镀层晶粒大小影响较大,Cu²⁺浓度的改变对镀层的平整度影响较大。电流密度增加、pH值下降、温度降低,都能使镀层结晶细致。     

p－Si上电沉积Ni－W合金薄膜

利用恒电流沉积法，在ｐ－Ｓｉ上制备出不同Ｗ含量和不同结构的Ｎｉ－Ｗ薄膜，研究了镀液温度，ｐＨ值，电流密度对镀层组成的影响，结果表明，提高温度有利于获得高Ｗ含量的合金．随着镀层中Ｗ含量的增加，Ｎｉ面心立方晶格ｆ．ｃ．ｃ发生正畸变，晶粒平均尺寸变小，当Ｗ含量达到５６％以上时，晶粒小于２ｎｍ，薄膜呈非晶态结构．     

镍硫析氢活性阴极的电化学制备及其电催化机理

以硫代硫酸钠作为硫源, 在基本的瓦特浴镀液体系中通过恒电流电沉积方法获得了不同晶体结构的镍硫合金活性阴极. 通过能量散射谱(EDS)、X射线衍射(XRD)以及扫描电子显微镜(SEM)对镀层的化学成分、晶体结构以及表面形貌进行了分析, 并对活性阴极的电催化活性以及析氢过程机理进行了研究. XRD测试结果表明, 随着镀层中硫含量的变化, 镀层的晶体结构呈现出非晶态/Ni3S2混晶和金属间化合物(Ni3S2)两种晶体结构, 其中, 硫含量为33.9%(原子分数)的非晶态/Ni3S2混晶结构的活性阴极在碱性溶液中具有很好的析氢活性, 其优良的析氢活性主要来自于Ni3S2很强的吸附氢能力. 交流阻抗的测试结果表明, Ni3S2金属间化合物的析氢过程只存在一个电化学反应步骤, 而非晶态/Ni3S2混晶镍硫合金活性阴极的析氢过程存在三个电化学反应步骤.     

Co-WC电极

从钴镀液中添加ＷＣ微粒复合电沉积制备Ｃｏ－ＷＣ镀层,ＷＣ微粒的加入,加快了阴极电化学反应．Ｃｏ－ＷＣ复合电极在碱性溶液中具有优越的电催化析氢性能,并经受了长期间断电解的试验,电极性能稳定     

亚硫酸盐无氰电沉积金新工艺及机制

直接以氯金酸作为主盐、 羟基乙叉二膦酸（HEDP）作为镀液稳定剂和镀层细化剂、 结合添加剂, 组成亚硫酸盐无氰镀金新工艺; 研究镀液稳定性、 镀层形态及金电沉积机制。结果表明, HEDP可明显提升镀液稳定性;不含HEDP的亚硫酸盐镀金液中, 镀层呈棒状晶粒并随沉积时间延长而逐渐生长,导致镀层外观随镀层厚度增加由金黄色转变为红棕色。镀液含有HEDP时, 金晶粒形态由棒状转变为棱锥状, 且棱锥状晶粒随沉积时间延长生长速率较小, 镀层厚度为1 μm时仍呈现金外观。电化学实验表明金电沉积不经历成核过程。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Selective syntheses of 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones via temperature-dependent Rh(II)-carbenoid-mediated 2H-azirine-ring expansion

The Rh(II)-catalyzed reaction of 2-carbonyl-substituted 2H-azirines with ethyl 2-cyano-2-diazoacetate or 2-diazo-3,3,3-trifluoropropionate provides an easy access to 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones. These compounds can be selectively prepared from the same starting material using temperature as the only varied parameter. The 2-azabuta-1,3-diene intermediate, a common precursor for both heterocyclic products, isomerizes into 2H-1,3-oxazine under kinetic control, while 1H-pyrrol-3(2H)-one is the sole product of the reaction at elevated temperatures. According to DFT-calculations a one-atom oxazine ring contraction involving ring-opening to a 2-azabuta-1,3-diene intermediate, followed by a 1,5- and 1,2-prototropic shift leads to the consecutive formation of imidoylketene and azomethine ylide, which then further undergo cyclization to the pyrrole derivative.     

Copper catalyzed/mediated synthetic methodology for ebselen and related isoselenazolones

Scope of the copper catalyzed/mediated selenium-nitrogen coupling reaction has been studied for the synthesis of isoselenazolones. It is noticed that the 2-chloro, 2-bromo-, and 2-iodo-aryl amides substrates can be exploited in the selenium-nitrogen coupling reaction by employing 25-100 mol % of CuI/1,10-phenanthroline (L) and potassium carbonate as a base in DMF. Furthermore, electron rich 2-chloro-arylamides also underwent selenium-nitrogen coupling reaction to give biologically important selenium-nitrogen heterocycles. Also, copper-catalyzed selenium-nitrogen coupling reaction has been meticulously applied for the synthesis of diaryl diselenides having methoxy, amine, and amide functionality from respective aryl iodides in the presence of stoichiometric amount of succinimide as an external Se-N coupling partner.     

Knoevenagel condensation catalyzed by novel Nmm-based ionic liquids in water

A series of novel N-methyl morpholine (Nmm) based ionic liquids with 1,2-propanediol group were synthesized and used as catalysts for Knoevenagel condensation at room temperature in water. Under the effect of the catalyst, various aldehydes or aliphatic ketones could react with a wide range of activated methylene compounds well, including malononitrile, alkyl cyanoacetate, cyanoacetamide, β-diketone, barbituric acid, 2-arylacetonitrile and thiazolidinedione. Furthermore, most of the products could be separated just by filtrating and washing with water. Additionally, the catalyst is recyclable and applicable for the large-scale synthesis.     

Construction of polyheterocyclic spirotetrahydrothiophene derivatives via sulfa-Michael/aldol cascade reaction

A series of polyheterocyclic spirotetrahydrothiophene derivatives were obtained in moderate to excellent yields via a catalyst-free sulfa-Michael/aldol cascade reaction of chalcones 1 and commercially available 1,4-dithiane-2,5-diol 2 under mild conditions. We also present the first asymmetric sulfa-Michael/aldol cascade reaction of chalcones 1 and commercially available 1,4-dithiane-2,5-diol 2 with moderate to good enantioselectivities catalyzed by readily available chiral phase-transfer catalysts (PTCs).     

Suzuki-Miyaura reactions of the soluble guanylate cyclase inhibitor NS2028: a non-product specific route to C-8 substituted analogues

Both soluble guanylate cyclase (sGC) inhibitors ODQ 1 and NS2028 2 are synthesized via improved protocols. In the former case treating 3,4-dihydroquinoxalin-2(1H)-one oxime 8, which can be prepared in two steps from 1,2-benzenediamine, with 1,1′-carbonyldiimidazole (CDI) gives the dihydro-ODQ 10 that in the presence of KMnO₄ oxidises to give ODQ 1 in an overall yield of 46% starting from 1,2-benzenediamine. In the latter case, the synthesis affords NS2028 2 from 2-amino-4-bromophenol 3 in three steps with an overall yield of 85% and avoids the need for chromatography. Furthermore, Suzuki-Miyaura reaction conditions are described that enable the preparation of 8-aryl and 8-heteroaryl derivatives of NS2028 directly from NS2028 2. Finally, demethylation of the 8-(methoxyphenyl) substituted analogues afforded the 8-(hydroxyphenyl) derivatives 40-42. All new products are fully characterised.