高分子凝胶电解质高氯酸锂 - 碳酸乙二醇酯 - 聚甲基丙烯酸甲酯体系的研究

研究了高分子凝胶电解质高氯酸锂 碳酸乙二醇酯 聚甲基丙烯酸甲酯体系（ＬｉＣｌＯ４ ＥＣ ＰＭＭＡ）的离子导电性、热稳定性和电化学稳定性．该体系的离子电导率与温度的关系服从ＶＴＦ方程．当ＬｉＣｌＯ４的浓度ＣＬｉＣｌＯ４＝１５ｍｏｌ／Ｌ、ＰＭＭＡｗｔ％（质量百分数）＝３５时，其离子电导率达极大值δ＝１９２×１０－３Ｓ／ｃｍ，光学透明度高，在空气中的稳定性较好，且具有一定的粘附性．该体系在１０２℃以下的热稳定性较高（失重率为３２８％）；电化学稳定性窗口为４５Ｖ，可满足固态电致变色“Ｓｍａｒｔ”窗的要求．     

含有添加剂及LiClO_4的接枝聚酯网络的离子导电性能研究

研究了碳酸丙烯酯（添加量５％）与γ－丁内酯（添加量１０％）对由数均分子量为８００的聚氧化乙烯（ＰＥＯ８００）大单体交联不饱和聚酯（含ＬｉＣｌＯ４）形成的接枝聚酯网络的离子导电性能影响，发现其电导率主要取决于体系中的ＬｉＣｌＯ４浓度．当［ＥＯ链节］／［Ｌｉ＋］＝３０时，室温电导率达最大值，σ２９８Ｋ＝（４．０—４．５）×１０－５Ｓｃｍ－１．这类接枝聚酯网络的玻璃化转变温度（Ｔｇ）同样取决于盐类浓度，而与网络的交联程度无关．网络中的极性添加剂并不显著影响其交联程度与Ｔｇ，但较大幅度提高离子导电性能，这可能与极性添加剂加速载荷离子在导电通道中的迁移性有关．若在上述接枝网络中引入环氧树脂网络，形成接枝聚合物互穿网络，则成膜后的机械强度有进一步提高，同时具有优良的室温电导率，σ２９８Ｋ＝２．４×１０－５Ｓｃｍ－１。     

固体电解质Li4.4M0.4Si0.6O4-xLi2O(M=Al,B)的低温合成及导电性

用溶胶－凝胶法,于７００℃合成了Ｌｉ４．４Ｍ０．４Ｓｉ０．６Ｏ４－ｘＬｉ２Ｏ（Ｍ＝Ａｌ,Ｂ;ｘ＝０．００－０．５０）离子导体材料,并用ＤＴＡ－ＴＧ、ＸＲＤ、ＳＥＭ及交流阻抗等技术对样品进行了测试,结果发现：用溶胶－凝胶法可降低Ｌｉ４．４Ｍ０．４Ｓｉ０．６Ｏ４的合成温度,随Ａｌ,Ｂ的掺杂,可提高基质材料的离子导电性,同时随Ｌｉ２Ｏ的掺入可增强样品的致密性并提高了其离子的导电性能。     

LiAgSO4-Al2O3复合电解质的导电性研究

研究了分散第二相α－Ａｌ２Ｏ３对ＬｉＡｇＳＯ４的离子导电性的影响，发现ＬｉＡｇＳＯ４－Ａｌ２Ｏ３的电导率随ａ－Ａｌ２Ｏ３含量的增加而升高，在３００－５００℃间电导率高于纯ＬｉＡｇＳＯ４，ａ－Ａｌ２Ｏ３含量摩尔比约为４０时最高。ＴＧ－ＤＴＡ和ＸＲＤ分析表明，在高温稳定的体立心ＬｉＡｇＳＯ４降温后以Ａｇ２ＳＯ４的正交β相形式存在，但在Ｈ２Ｏ存在下，生成Ｌｉ２ＳＯ４．Ｈ２Ｏ和Ａｇ２ＳＯ４．ＦＴ－ＩＲ分析     

聚氧乙烯－高氯酸锂配合物电致变色光窗的研究

以ＷＯ３为电致变色层、ＮｉＯｘ为离子贮存层、具有较好透光性的氧亚甲基连接聚氧乙烯／ＬｉＣｌＯ４，配合物为电解质制备了全固态电致变色光窗。电色窗在７００～９００ｎｍ之间的调制深度超过５０％。电色窗的电色能力随温度的升高及ＬｉＣｌＯ４盐浓度的增大而加强，并且电色窗具有较好的信息贮存能力。     

聚醋酸乙烯酯与铜（Ⅱ）离子的配位反应及其催化作用

以ＥＳＲ、ＵＶ和ＩＲ表征Ｃｕ（２＋）离子与ＰＶＡＣ的配位反应。根据ＣＵＣｌ２·２Ｈ２Ｏ乙醇溶液与ＰＶＡｃ－ＣｕＣｌ２·２Ｈ２Ｏ乙醇溶液的电导率差值随Ｃｕ（２＋）离子摩尔浓度变化的明显转析点得知，１个Ｃｕ（２＋）离子大约能与ＰＶＡｃ４个链节单元配位。证实ＭＭＡ在Ｃｕ（Ⅱ）－ＰＶＡｃ配合物／Ｎａ２ＳＯ３体系的聚合体是无规ＰＭＭＡ，得率为７０％。讨论了ＭＭＡ在Ｃｕ（Ⅱ）－ＰＶＡｃ配合物／Ｎａ２ＳＯ３体系络合催化引发下的游离基反应历程。     

含NaI的环氧树脂—PEO互穿网络高分子固体电解质的离子电导研究

制备了含ＮａＩ的环氧树脂－ＰＥＯ４００的ＩＰＮ高分子固体电解质。Ｘ－射线衍射分析表明，这类材料在所研究的范围内呈非晶相。测量了其离子电导率，其最佳室温离子电导率达７．８×１０＾－５Ｓ·ｃｍ＾－１，与含ＮａＣｌＯ４、ＬｉＣｌＯ４的ＩＰＮ材料的电导率相差不多，但比ＮａＩ－ＰＥＯ材料的最佳的室温离子电导率高得多。含ＮａＩ的ＩＰＮ薄膜材料具有机械强度高、粘弹性好、透明度好以及易于成膜等优点。     

聚合物-锂改性蒙脱石复合材料离子迁移

以聚合物（ＰＥＯ,ＰＥＯ－ＰＭＭＡ）和锂改性蒙脱石作为主要原料,采用聚合物粉末直接熔融嵌入的方法,制备聚合物－蒙脱石复合材料．利用ＮＭＲ、ＡＣ阻抗等分析方法探讨了复合材料中聚合物链对 Ｌｉ＋离子迁移的影响．结果表明,聚合物（ＰＥＯ）嵌入蒙脱石层间,层间聚合物链的无序度增大,有利于Ｌｉ＋离子迁移．ＰＭＭＡ引入对ＰＥＯ链的改性,进一步加大聚合物链的无序度,更易于层间Ｌｉ＋离子迁移;复合材料的常温离子电导率接近１０－２Ｓ·ｃｍ－１,且具有良好的温度稳定性．     

聚氧乙烯—高氯酸锂配合笺电致变色光窗的研究

以ＷＯ３为电致变色层，ＮｉＯｘ为离子贮存层，具有较好透光性的氧亚甲基连接聚氧乙烯／ＬｉＣｌＯ４配合物为电解质制备了全固态电致变色光窗。电色窗在７００－９００ｎｍ之辜的调制深度超过５０％。     

（四甲基二硅撑）双（3－三甲硅基环戊二烯基）－四羰基二铁的反应性

标题化合物（Ｍｅ_２ＳｉＳｉＭｅ_２）［η￣５－（３－Ｍｅ_３ＳｉＣ_５Ｈ_３）Ｆｅ（ＣＯ）_２］_２／（μ－ＣＯ）_２（Ａ）分子中的Ｆｅ－Ｆｅ键被钠汞齐还原断裂，生成相应的双铁负离子，分别与ＭｅＣＯＣｌ、ＰｈＣＯＣｌ、ＰｈＣＨ_２Ｃｌ、ＣｌＣＨ_２ＣＯＯＣ_２Ｈ_５和Ｐｈ_３ＳｎＣｌ进行亲核取代反应，生成在铁原子上引入相应取代基的产物（Ｍｅ_２ＳｉＳｉＭｅ_２）［η￣５－（３－Ｍｅ_３ＳｉＣ_５Ｈ_３）Ｆｅ（ＣＯ）_２Ｒ］_２（Ｒ：ＭｅＣＯ（１），ＰｈＣＯ（２），ＰｈＣＨ_２（３），ＣＨ_２ＣＯＯＣ_２Ｈ_５（４），Ｐｈ_３Ｓｎ（５），Ｉ（６））。Ａ在氯仿中与碘反应，得到Ｆｅ－Ｆｅ断裂的双铁碘化物，但在苯中与过量碘反应，则得到Ｆｅ－Ｉ－Ｆｅ桥联的离子型化合物（Ｍｅ_２ＳｉＳｉＭｅ_２）［η￣５－（３－Ｍｅ_３ＳｉＣ_５Ｈ_３）Ｆｅ（ＣＯ）_２］_２Ｉ·Ｉ（７）。化合物６的晶体和分子结构经Ｘ射线衍射测定，６属单斜晶系，Ｐ２１／ｃ空间群，ａ＝１．７２１７（４）ｎｍ，ｂ＝０．７７５３（２）ｎｍ，Ｃ＝１．３６２９（７）ｎｍ，β＝１０３．８０（３）°，Ｖ＝１．７６７（２）ｎｍ３，Ｚ＝４，Ｄｃ＝１．６２９９·ｃｍ－１，最终偏差因子Ｒ＝０．０５４。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

Selective syntheses of 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones via temperature-dependent Rh(II)-carbenoid-mediated 2H-azirine-ring expansion

The Rh(II)-catalyzed reaction of 2-carbonyl-substituted 2H-azirines with ethyl 2-cyano-2-diazoacetate or 2-diazo-3,3,3-trifluoropropionate provides an easy access to 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones. These compounds can be selectively prepared from the same starting material using temperature as the only varied parameter. The 2-azabuta-1,3-diene intermediate, a common precursor for both heterocyclic products, isomerizes into 2H-1,3-oxazine under kinetic control, while 1H-pyrrol-3(2H)-one is the sole product of the reaction at elevated temperatures. According to DFT-calculations a one-atom oxazine ring contraction involving ring-opening to a 2-azabuta-1,3-diene intermediate, followed by a 1,5- and 1,2-prototropic shift leads to the consecutive formation of imidoylketene and azomethine ylide, which then further undergo cyclization to the pyrrole derivative.