Determination of sibiromycin and its natural derivatives using new analytical and structural approaches

A new separation and quantification method using ultra high-performance liquid chromatography (UHPLC) with UV detection was developed for the detection of sibiromycin in fermentation broth of Streptosporangium sibiricum. The solid phase extraction method based on cation-exchange was employed to pre-concentrate and purify fermentation broth containing sibiromycin prior to UHPLC analysis. The whole assay was validated and showed a linear range of detector response for the quantification of sibiromycin in a concentration from 3.9 to 250.0 μg mL⁻¹, with correlation coefficient of 0.999 and recoveries ranging from 71.66 ± 3.55% to 74.76 ± 5.18%. Method limit of quantification of the assay was determined as 0.18 μg mL⁻¹ and was verified with resulting RSD of 9.6% and accuracy of 97.6%. The developed assay was used to determine the sibiromycin production in 12 different fermentation broths. Moreover, several natural sibiromycin analogues/derivatives were described with pilot characterization using off-line mass spectrometry: the previously described dihydro-sibiromycin (DH-sibiromycin) and tentative bis-glycosyl forms of sibiromycin and its dihydro-analogue.     

Photodiode array to charged aerosol detector response ratio enables comprehensive quantitative monitoring of basic drugs in blood by ultra-high performance liquid chromatography

Quantitative screening for a broad range of drugs in blood is regularly required to assess drug abuse and poisoning within analytical toxicology. Mass spectrometry-based procedures suffer from the large amount of work required to maintain quantitative calibration in extensive multi-compound methods. In this study, a quantitative drug screening method for blood samples was developed based on ultra-high performance liquid chromatography with two consecutive detectors: a photodiode array detector and a corona charged aerosol detector (UHPLC–DAD–CAD). The 2.1 mm × 150 mm UHPLC column contained a high-strength silica C18 bonded phase material with a particle size of 1.8 μm, and the mobile phase consisted of methanol/0.1% trifluoroacetic acid in gradient mode. Identification was based on retention time, UV spectrum and the response ratio from the two detectors. Using historic calibration over a one-month period, the median precision (RSD) of retention times was 0.04% and the median accuracy (bias) of quantification 6.75%. The median precision of the detector response ratio over two orders of magnitude was 12%. The applicable linear ranges were generally 0.05–5 mg L⁻¹. The method was validated for 161 compounds, including antipsychotics, antidepressants, antihistamines, opioid analgesics, and adrenergic beta blocking drugs, among others. The main novelty of the method was the proven utility of the response ratio of DAD to CAD, which provided the additional identification efficiency required. Unlike with mass spectrometry, the high stability of identification and quantification allowed the use of facile historic calibration.     

Rapid and sensitive ultra‐high‐pressure liquid chromatography method for quantification of antichagasic benznidazole in plasma: application in a preclinical pharmacokinetic study

Benznidazole (BNZ) and nifurtimox are the only drugs available for treating Chagas disease. In this work, we validated a bioanalytical method for the quantification of BNZ in plasma aimed at improving sensitivity and time of analysis compared with the assays already published. Furthermore, we demonstrated the application of the method in a preclinical pharmacokinetic study after administration of a single oral dose of BNZ in Wistar rats. A Waters® Acquity UHPLC system equipped with a UV–vis detector was employed. The method was established using an Acquity® UHPLC HSS SB C₁₈ protected by an Acquity® UHPLC HSS SB C₁₈ VanGuard guard column and detection at 324 nm_. The mobile phase consisted of ultrapure water–acetonitrile (65:35), and elution was isocratic. The mobile phase flow rate was 0.55 mL/min, the volume of injection was 1 μL, and the run time was just 2 min. The samples were kept at 25°C until injection and the column at 45°C for the chromatographic separation. The sample preparation was performed by a rapid protein precipitation with acetonitrile. The linear concentration range was 0.15–20 µg/mL. The pharmacokinetic parameters of BNZ in rats were determined and the method was considered sensitive, fast and suitable for application in pharmacokinetic studies. Copyright © 2014 John Wiley & Sons, Ltd.     

On-line high-performance liquid chromatography–ultraviolet–nuclear magnetic resonance method of the markers of nerve agents for verification of the Chemical Weapons Convention

This paper details an on-flow liquid chromatography–ultraviolet–nuclear magnetic resonance (LC–UV–NMR) method for the retrospective detection and identification of alkyl alkylphosphonic acids (AAPAs) and alkylphosphonic acids (APAs), the markers of the toxic nerve agents for verification of the Chemical Weapons Convention (CWC). Initially, the LC–UV–NMR parameters were optimized for benzyl derivatives of the APAs and AAPAs. The optimized parameters include stationary phase C₁₈, mobile phase methanol:water 78:22 (v/v), UV detection at 268 nm and ¹H NMR acquisition conditions. The protocol described herein allowed the detection of analytes through acquisition of high quality NMR spectra from the aqueous solution of the APAs and AAPAs with high concentrations of interfering background chemicals which have been removed by preceding sample preparation. The reported standard deviation for the quantification is related to the UV detector which showed relative standard deviations (RSDs) for quantification within ±1.1%, while lower limit of detection upto 16 μg (in μg absolute) for the NMR detector. Finally the developed LC–UV–NMR method was applied to identify the APAs and AAPAs in real water samples, consequent to solid phase extraction and derivatization. The method is fast (total experiment time ∼2 h), sensitive, rugged and efficient.     

UHPLC method for the simultaneous determination of β-blockers, isoflavones, and flavonoids in human urine

A simple method using solid-phase extraction (SPE) and ultra high-performance liquid chromatography (UHPLC) for the simultaneous determination of β-blockers, isoflavones, and flavonoids in human urine is developed. A statistical central composite design and response surface analysis is used to optimize the separation of the analytes. These multivariate procedures are efficient in determining the optimal separation condition using resolutions and retention time as responses. A gradient elution using a mobile phase consisting of 0.05% trifluoroacetic acid in water and acetonitrile is applied on a Hypersil GOLD column within a short analysis time of 4.5 min. UV detection was used to monitor the analytes. The suggested method was linear in a concentration range from 0.04-20.00 μg/mL, depending on the compound. The limits of detection ranged from 8.9 to 66.2 ng/mL. The precision was lower than 2.74%, and the accuracy was between 0.01-3.65%. The Oasis HLB column, with the highest recoveries, is selected for the pre-concentration step. This present paper reports, for the first time, a method for the simultaneous determination of β-blockers, isoflavones, and flavonoids in human urine samples. Furthermore, the developed method can also be applied to the routine determination of examined compounds concentrations in human urine.     

Determination of eight penicillin antibiotics in pharmaceuticals,milk and porcine tissues by nano-liquid chromatography

This study describes the ability of nanoscale liquid chromatography (nano-LC) coupled with UV or mass spectrometry (MS) for the simultaneous determination of eight common penicillin antibiotics (amoxicillin, ampicillin, penicillin G, penicillin V, oxacillin, cloxacillin, nafcillin and dicloxacillin) in commercial samples (pharmaceuticals, milk, porcine tissues (liver and kidney)) for the first time. Material types of the on-column polymeric frits (polystyrene-based and polymethacrylate-based monoliths) and the packed stationary phase materials (C8 and C18 particles of 3 μm) used in the nano-LC for the influence of penicillin separation were evaluated. The nano-LC and MS parameters such as the composition and flow rate of mobile phase, capillary voltage and temperature of dry gas were examined in order to acquire high separation resolution and detection sensitivity for penicillin analyses. Furthermore, a home-made in-line filter (a nylon membrane of 0.2 μm pore size), was first used to connect with the flow cell of high sensitivity UV detector or the nanoelectrospray needle in MS detection. The result indicated it could effectively improve the reproducibility of penicillin mass signals or prolong the lifetime of the flow cell. The nano-LC methods provided good quantitative precisions in the range of 89.5–111.2% for UV detection at 0.5 μg/mL penicillins, and 83. 1–94.9% for MS detection at 5 μg/L penicillins), respectively, as well as offered stable retention repeatabilities (the relative standard deviation (RSD) of retention time was lower 0.30% in both the UV and MS detections). Compared to other LC–MS methods, the proposed nano-LC systems provided better detection sensitivity for these penicillins (the limits of detection (LOD) was of 2.27–4.06 μg/L for UV mode, and 0.01–0.51 μg/L for MS mode) when either UV or MS detector was employed.     

Determination of ng/mL levetiracetam using ultra-high-performance liquid chromatography-photodiode absorbance

This paper demonstrates the analysis of levetiracetam, a new chiral antiepileptic drug, at ng/mL levels using an ultra-high-performance liquid chromatography (UHPLC)-photodiode absorbance (PDA) method. Three different sample preparation methods, liquid-liquid extraction with Extrelut, solid phase extraction (SPE) with Oasis HLB and Oasis MAX SPE cartridges, and protein precipitation with organic solvents were carried out. The last preparatory method is the simplest and provides the best recoveries: between 97.1% and 100.4% with RSD value below 5%. The column for separation is BEH C18 column (1.7 μm particle size and 100 × 2.1 mm i.d.) and acetonitrile-phosphate buffer (pH = 6.6; 0.01 M) (10/90 v/v) is the mobile phase. The results obtained are compared to analysis conducted by the HPLC method. The UHPLC method was validated in the range of 2-100 μg/mL levetiracetam concentration (R(2) = 0.9997). LOD and LOQ are 10 ng/mL and 33 ng/mL, respectively. The developed UHPLC method was applied to plasma samples of patient with epilepsy.     

High throughput qualitative analysis of polyphenols in tea samples by ultra-high pressure liquid chromatography coupled to UV and mass spectrometry detectors

The analysis of polyphenols in tea extracts is important due to their potential health benefits. Therefore, efficient and high throughput analytical methods have been developed for the separation of seven predominant polyphenols, also known as catechin derivatives, present in tea extracts. Columns packed with sub-2-μm particles operating at elevated pressure (UHPLC strategy) were selected to improve chromatographic performance. The potential of UHPLC–UV was demonstrated with baseline resolution of all standard catechins in only 30 s using a 50-mm column packed with 1.7-μm particles. When dealing with real samples such as tea extracts, however, longer columns of up to 150 mm in length were employed to enhance the separation of catechin derivatives and other constituents within the tea samples while maintaining an acceptable analysis time. Two strategies based on 2-D experiments were proposed to clearly identify catechins. Firstly, a liquid–liquid extraction procedure was added prior to the UHPLC–UV analysis to decrease the complexity of the sample. Secondly, UHPLC was coupled to ESI-MS/MS to attain sufficient sensitivity and selectivity between catechin derivatives and other constituents of tea extract. These two strategies were found extremely promising as a clear discrimination of catechins from the matrix could be attained.     

Reversed phase liquid chromatography with UV absorbance and flame ionization detection using a water mobile phase and a cyano propyl stationary phase Analysis of alcohols and chlorinated hydrocarbons

The development of liquid chromatography with a commercially available cyano propyl stationary phase and a 100% water mobile phase is reported. Separations were performed at ambient temperature, simplifying instrumental requirements. Excellent separation efficiency using a water mobile phase was achieved, for example N=18 800, or 75 200 m(-1), was obtained for resorcinol, at a retention factor of k'=4.88 (retention time of 9.55 min at 1 ml min(-1) for a 25 cmx4.6 mm i.d. column, packed with 5 mum diameter particles with the cyano propyl stationary phase). A separation via reversed phase liquid chromatography (RP-LC) with a 100% water mobile phase of six phenols and related compounds was compared to a separation of the same compounds by traditional RP-LC, using octadecylsilane (ODS), i.e. C18, bound to silica and an aqueous mobile phase modified with acetonitrile. Nearly identical analysis time was achieved for the separation of six phenols and related compounds using the cyano propyl stationary phase with a 100% water mobile phase, as compared to traditional RP-LC requiring a relatively large fraction of organic solvent modifier in the mobile phase (25% acetonitrile:75% water). Additional understanding of the retention mechanism with the 100% water mobile phase was obtained by relating measured retention factors of aliphatic alcohols, phenols and related compounds, and chlorinated hydrocarbons to their octanol:water partition coefficients. The retention mechanism is found to be consistent with a RP-LC mechanism coupled with an additional retention effect due to residual hydroxyl groups on the cyano propyl stationary phase. Advantages due to a 100% water mobile phase for the chemical analysis of alcohol mixtures and chlorinated hydrocarbons are reported. By placing an absorbance detector in-series and preceding a novel drop interface to a flame ionization detector (FID), selective detection of a separated mixture of phenols and related compounds and aliphatic alcohols is achieved. The compound class of aliphatic alcohols is selectively and sensitively detected by the drop interface/FID, and the phenols and related compounds are selectively and sensitively detected by absorbance detection at 200 nm. The separation and detection of chlorinated hydrocarbons in a water sample matrix further illustrated the advantages of this methodology. The sensitivity and selectivity of the FID signal for the chlorinated hydrocarbons are significantly better than absorbance detection, even at 200 nm. This methodology is well suited to continuous and automated monitoring of water samples. The applicability of samples initially in an organic solvent matrix is explored, since an organic sample matrix may effect retention and efficiency. Separations in acetonitrile and isopropyl alcohol sample matrices compared well to separations with a water sample matrix.     

超临界流体色谱对吴茱萸中吲哚类生物碱的快速分析

建立了超临界流体色谱快速分析吴茱萸中吲哚类生物碱的方法。以标准品混合物和复杂样品为对象比较4种色谱柱的分离效果,进行色谱柱的筛选;考察了进样体积、改性剂、添加剂、温度和背压对保留行为的影响。结果表明,进样体积对峰形影响显著;添加剂对保留时间和色谱峰形影响有限;改变改性剂能使保留时间显著改变;降低温度,升高背压,保留时间减小。经过优化,确定采用Waters ACQUITY UPC² BEH色谱柱,以甲醇为改性剂,在35 ℃柱温和2.07×10⁷ Pa背压条件下,15 min内完成复杂样品的分析。同时采用超高效液相色谱完成复杂样品的快速分析。结果表明,超临界流体色谱可用于天然产物的高效快速分析,同时该方法与超高效液相色谱在分离选择上的差异有助于天然产物分析方法的拓展。     

Hydrophobic solvent induced phase transition extraction to extract drugs from plasma for high performance liquid chromatography–mass spectrometric analysis

Novel sample preparation approaches for HPLC bioanalysis based on the phenomenon that acetonitrile can be separated from water by adding salts or cooling at subzero temperatures have been reported. These two methods are superior to conventional liquid–liquid extraction since the separated acetonitrile phase can be directly injected to the RP–LC system. However, the salting-out method suffers from a potential problem that the remained salt in the acetonitrile phase may harm the MS detector, while the subzero-temperature method is troublesome to operate. Here, we have reported a similar phase separation phenomenon that the acetonitrile aqueous mixture can be separated by adding a hydrophobic solvent; and capitalising on this phase transition phenomenon, we have proposed an alternative approach, named solvent induced phase transition extraction (SIPTE), to extract drug from plasma for HPLC–MS analysis. The proposed SIPTE method is much simpler and avoids contaminating the MS detector. Three structurally diverse drugs were selected as test compounds to design the SIPTE method and to validate the efficiency of this method. The four goals of plasma sample pretreatment for HPLC–MS analysis, i.e. removal of proteins, removal of other low-molecular interferences, preconcentration of the analytes of interest, and matching the sample solvent with the HPLC–MS system, can be rapidly performed in a very simple step by using the SIPTE method.     

Development and validation of an RP-HPLC-UV method for the determination of BOL-303225-A, a new coumarin-based anti-inflammatory drug, in rat plasma

A simple and rapid high-performance liquid chromatographic method was developed and validated for the analysis in rat plasma of BOL-303225-A, a new coumarin-based anti-inflammatory drug. Liquid-liquid extraction was used for sample preparation. Chromatographic separation was achieved on a C(18) column using acetonitrile and water containing 1% triethylamine pH 3.5, adjusted with orthophosphoric acid (35.5:64.5 v/v) as mobile phase. The UV detector was set at 324 nm. The method proved to be linear (r(2) > 0.99) and precise (RSD < 7%) over the concentration range 29-940 ng/mL, and was suitable for the support of pharmacokinetic studies in rats.     

Preparation of monodispersed vinylpyridine–divinylbenzene porous copolymer resins and their application to high-performance liquid chromatographic separation of aromatic amines

For the separation of aromatic amines, two types of monodispersed porous polymer resins were prepared by the copolymerization of 2-vinylpyridine and 4-vinylpyridine with divinylbenzene in the presence of template silica gel particles (particle size 5 μm), followed by dissolution of the template silica gel in an alkaline solution. The transmission electron micrographs and the scanning electron micrograph revealed that these templated polymer resins have a spherical morphology with a good monodispersity and porous structure. Using these monodispersed polymer resins, the high-performance liquid chromatographic separation of aromatic amines in the mobile phases of pHs 2.0, 2.9, 4.1, 7.2 and 11.7 were carried out. The 2-vinylpyridine–divinylbenzene copolymer resins showed slightly stronger retentions for aromatic amines than the 4-vinylpyridine–divinylbenzene copolymer resins. Under acidic conditions (around pH 2.0), aniline and the toluidines showed no retention on these copolymer resins due to the repulsion between the cationic forms of these amines and pyridinium cations in the stationary phase, whereas less basic aromatic amines or non-basic acetanilide showed slight retentions. Above pH 4.1, the separation of aromatic amines with these polymer resins showed a typical reversed-phase mode separation. Therefore, the separation patterns of aromatic amines are effectively tunable by changing the pH value of the mobile phases. A good separation of eight aromatic amines was achieved at pH 2.9 using the 2-vinylpyridine–divinylbenzene copolymer resins.     

Optimization of hydrophilic interaction LC by univariate and multivariate methods and its combination with salting‐out liquid–liquid extraction for the determination of antihypertensive drugs in the environmental waters

Hydrophilic interaction LC for the separation of four antihypertensive drugs was optimized by both univariate and multivariate methods. The column efficiency, resolution, and separation time were used as the three assessment parameters. The best separation condition of 97% ACN with 3% aqueous buffer containing 50 mM ammonium acetate at a pH of 3.0 was obtained by the two optimization methods. The multivariate optimization, orthogonal array design herein, was demonstrated to be a little tedious, but afforded a much better understanding of underlying separation factors. The content of ACN in the mobile phase contributed most significantly to separation. Furthermore, sample diluent and injection volume were found to influence the chromatographic performance. To match the hydrophilic interaction LC mobile phase, a proper sample pretreatment method, salting‐out liquid–liquid extraction, in which ACN was the extractant, was chosen. Since reserpine was unstable under both acidic and alkaline conditions, it was not studied in this part. The optimal salting‐out liquid–liquid extraction parameters were as follows: 400 μL ACN was added to 1 mL sample solution containing 500 mg NH₄Cl at a pH of 14.0. The linearity ranged from 0.01 to 1.00 μg/mL with r² > 0.9937. The LODs were between 1.9 and 2.5 ng/mL. The developed method was applied to the environmental water sample with good performance.     

Indirect ultraviolet detection of alkaline earth metal ions using an imidazolium ionic liquid as an ultraviolet absorption reagent in ion chromatography

A convenient and versatile method was developed for the separation and detection of alkaline earth metal ions by ion chromatography with indirect UV detection. The chromatographic separation of Mg²⁺, Ca²⁺, and Sr²⁺ was performed on a carboxylic acid base cation exchange column using imidazolium ionic liquid/acid as the mobile phase, in which the imidazolium ionic liquid acted as an UV‐absorption reagent. The effects of imidazolium ionic liquids, detection wavelength, acids in the mobile phase, and column temperature on the retention of Mg²⁺, Ca²⁺, and Sr²⁺ were investigated. The main factors influencing the separation and detection were the background UV absorption reagent and the concentration of hydrogen ion in ion chromatography with indirect UV detection. The successful separation and detection of Mg²⁺, Ca²⁺, and Sr²⁺ within 14 min were achieved using the selected chromatographic conditions, and the detection limits (S /N = 3) were 0.06, 0.12, and 0.23 mg/L, respectively. A new separation and detection method of alkaline earth metal ions by ion chromatography with indirect UV detection was developed, and the application range of ionic liquids was expanded.     

Metabolite profiling of plant extracts by ultra-high-pressure liquid chromatography at elevated temperature coupled to time-of-flight mass spectrometry

Detailed metabolite profiling of crude plant extracts, mandatory for both quality control and metabolomics purposes, requires high-resolution separation and sensitive detection with a reasonable sample throughput. In this respect, the use of ultra-high-pressure liquid chromatography (UHPLC) working at high temperature (HT) and coupled to time-of-flight mass spectrometry (TOF-MS) was evaluated in the present study in terms of achievable peak capacities for given analysis times. Prior to the analysis of complex mixtures, the effects of TOF-MS detection on peak capacity were evaluated, and a loss of 15–30% compared to UV was observed due to the additional band broadening generated by this detector. Extracts from a model plant Arabidopsis thaliana and from a widely used phytochemical preparation Ginkgo biloba, as well as a standard mixture of representative natural products (NPs), have been analyzed. As expected from the theory, the increase in mobile phase temperature of up to 90 °C for the profiling of extracts containing metabolites spread over a large polarity range (e.g., Arabidopsis thaliana) generated similar peak capacities to those obtained at room temperature, but with a 2- to 3-fold reduction in analysis time, demonstrating the power of this approach for such applications. On the other hand, for the analysis of more polar extracts (e.g., Ginkgo biloba), the use of higher temperature was not beneficial, as it induced a significant decrease in retention, and thus resolving power, because of the increase in elution strength. The use of HT-UHPLC–TOF-MS raised the question of NP stability under high temperature conditions. This work demonstrated that no apparent degradation was evidenced at high temperature for a representative mixture of NPs and also for the different metabolites detected in the selected plant extracts.     

Polyacrylamide-based monolithic capillary column with coating of cellulose tris(3,5-dimethylphenyl-carbamate) for enantiomer separation in capillary electrochromatography

A hydrophilic chiral capillary monolithic column for enantiomer separation in CEC was prepared by coating cellulose tris(3,5-dimethylphenyl-carbamate) (CDMPC) on porous hydrophilic poly(acrylamide-co-N,N'-methylene-bisacrylamide) (poly(AA-co-MBA)) monolithic matrix with confine of a fused-silica capillary. The coating conditions were optimized to obtain a stable and reproducible chiral stationary phase for CEC. The effect of organic modifier of ACN in aqueous mobile phase for the enantiomer separation by CEC was investigated, and the significant influence of ACN on the enantioresolution and electrochromatographic retention was observed. Twelve pairs of enantiomers including acidic, neutral, and basic analytes were tested and nine pairs of them were baseline-enantioresolved with acidic and basic aqueous mobile phases. A good within-column repeatability in retention time (RSD = 2.4%) and resolution (RSD = 3.2%) was obtained by consecutive injections of a neutral compound, benzoin, on a prepared chiral monolithic column, while the between-column repeatability in retention time (RSD = 6.4%) and resolution (RSD = 9.6%) was observed by column-to-column examination. The prepared monolithic stationary phase showed good stability in either acidic or basic mobile phase.     

Capillary electrochromatographic separation of illicit drugs employing a cyano stationary phase

In this study, we present a capillary electrochromatographic method for separation of basic compounds of interest in forensic science (amphetamine, methamphetamine, 3,4-methylenedioxyamphetamine, 3,4-methylenedioxymethamphetamine, 3,4-methylenedioxyethylamphetamine, cocaine, codeine, heroin, morphine, and 6-monoacethylmorphine). Several analytical conditions were taken into account to completely separate in the same run the 10 drugs of abuse analyzed. Chromatographic retention, selectivity and efficiency were evaluated in dependence of the type of stationary phase (CN and RP-C₁₈ derivatized silica particles), mobile phase composition, buffer type and pH, sample injection. The optimum separation parameters were set up using a mixture of aqueous sodium phosphate buffer (pH 2.5)/acetonitrile (80/20, v/v) as the mobile phase, 10 kV and 20 °C as applied voltage and capillary temperature, respectively. Under these conditions all the studied analytes were baseline resolved within 20 min. The method performance was investigated in terms of precision, linearity, sensitivity and accuracy to demonstrate the applicability of the developed capillary electrochromatographic system to forensic analysis. Calibration curves provided a good linearity over a working range of 100–1200 ng/mL for all analytes. Limits of detection and quantification were in the range 5–12 ng/mL and 10–30 ng/mL, respectively. Then the method was applied to the analysis of a human urine sample spiked with a basic compounds’ mixture. Urine samples’ pre-treatment was carried out through a solid phase extraction (SPE) procedure on strong cation exchange (SCX) cartridges.     

Implications of on-line FTIR detection in the separation of coal-derived products via HPLC with polar modifiers

Summary Fourier-transform infrared spectrometry (FTIR) was utilized as a detection system for high-performance liquid chromatography of polar compounds on a normal bonded-phase system. In addition to FTIR, UV (254 nm) and refractive index detection were employed in the separation of model compounds containing oxygen and nitrogen atoms in their molecules (phenols, alcohols, neutral and weakly basic nitrogen compounds). A polar amino-cyano (PAC) bonded-phase column was employed with a binary mobile phase (98:2 CDCl₃:CH₃CN). The separations and the information gained from each detector is discussed, including interactions between sample material and mobile phase. A polar fraction of a coal-derived product is also chromatographed under identical conditions. The results based on FTIR detection and chromatographic retention behavior suggest the exclusive presence of hindered and unhindered phenols.     

Development of an ultra-high performance liquid chromatography analytical methodology for the profiling of olive (Olea europaea L.) pulp proteins

Ultra-high performance liquid chromatography (UHPLC) constitutes an interesting proposal to speed protein separations but it is almost not explored. In this work UHPLC is proposed, for the first time, to separate olive pulp proteins. An important difficulty in the analysis of proteins is related to their extraction. The difficulty in the extraction of proteins from the olive pulp is derived from its high content in lipids and phenolic compounds. Eight different methods for the extraction of pulp proteins were designed and evaluated. The optimized extraction procedure consisted of a cleaning step to remove interfering compounds, followed by the extraction of proteins with a Tris–HCl buffer containing sodium dodecyl sulphate (SDS) and dithiothreitol (DTT), precipitation of proteins with acetone, and solubilization in the Tris–HCl buffer. This methodology yielded the most successful isolation of pulp proteins and enabled the optimization of a UHPLC methodology for their separation. The method was applied to the profiling of olive pulp proteins from different olive cultivars observing in all cases a protein that had never been described before.