Influence of deposition conditions on nanocrystalline InN layers synthesized on Si(1 1 1) and GaN templates by RF sputtering

We present a detailed investigation on the influence of deposition conditions on morphological, structural and optical properties of InN films deposited on Si(1 1 1) and GaN-on-sapphire templates by reactive radio-frequency (RF) sputtering. The deposition parameters under study are nitrogen content in the sputtering gas, substrate–target distance, substrate temperature and RF power. X-ray diffraction measurements confirm the (0 0 0 1) preferred growth orientation and the wurtzite crystallographic structure of the material. For optimized deposition conditions, InN on Si(1 1 1) substrates presents smooth surface with root-mean-square roughness ∼1 nm. Surface quality of the InN films can be further improved by deposition on GaN-on-sapphire templates, achieving root-mean-square roughness as low as ∼0.4 nm, comparable to that of the underlying substrate. The room-temperature absorption edge is located at 1.70 eV. Intense low-temperature photoluminescence peaking at 1.60 eV is observed.     

Effect of the N/Al ratio of AlN buffer on the crystal properties and stress state of GaN film grown on Si(1 1 1) substrate

The effect of the N/Al ratio of AlN buffers on the optical and crystal quality of GaN films, grown by metalorganic chemical vapor deposition on Si(1 1 1) substrates, has been investigated. By optimizing the N/Al ratio during the AlN buffer, the threading dislocation density and the tensile stress have been decreased. High-resolution X-ray diffraction exhibited a (0 0 0 2) full-width at half-maximum as low as 396 acrsec. The variations of the tensile stress existing in the GaN films were approved by the redshifts of the donor bound exiton peaks in the low-temperature photoluminescence measurement at 77 K.     

GaP:Mg layers grown on GaN by MOCVD

We have investigated the growth of magnesium-doped GaP (GaP:Mg) layers on GaN by metalorganic chemical vapor deposition. The hole carrier concentration increased linearly from 0.8×10¹⁸ to 4.2×10¹⁸ cm⁻³ as the Bis(cyclopentadienyl) magnesium (Cp₂Mg) mole flow rate increased from 1.2×10⁻⁷ to 3.6×10⁻⁷ mol/min. However, the hole carrier concentration decreased when the CP₂Mg mole flow rate was further increased. The double crystal X-ray diffraction (DCXRD) rocking curves showed that the GaP:Mg layers were single crystalline at low CP₂Mg molar flow. However, the GaP:Mg layers became polycrystalline if the CP₂Mg molar flow was too high. The decrease in hole carrier concentration at high CP₂Mg molar flow was due to crystal quality deterioration of the GaP layer, which also resulted in the low hole mobility of the GaP:Mg layer.     

Atomic ordering in GaAsSb (0 0 1) grown by metalorganic vapor phase epitaxy

Epitaxial GaAsSb (0 0 1) semiconductor alloys grown by metalorganic vapor phase epitaxy exhibit several spontaneously ordered structures. A superlattice structure with three-fold ordering in the [1 1 0] direction has been previously observed by different groups. CuAu structures with (1 0 0) and (0 1 0) ordering planes have also been reported. The physical origin of CuAu ordering in III–V semiconductors has not yet been explained. In this work we report the effect of growth conditions on CuAu ordering in GaAsSb, including miscut from (0 0 1), growth rate, bismuth surfactant concentration, and growth temperature. These data point to a surface kinetic mechanism not based on dimer strain, but possibly due to one-dimensional ordering at step edges.     

Reduction of tensile stress in GaN grown on Si(1 1 1) by inserting a low-temperature AlN interlayer

We studied the selective growth behaviors of InP through narrow openings (<2 μm) by metal-organic chemical vapor deposition. The lateral overgrowth was observed to be significantly affected by both the opening width and orientation. It was found that the lateral overgrowth length reached the maximum at 60° off [0 1 1] direction. The lateral overgrowth also showed a ‘diffraction-like’ behavior, with the overgrowth length increasing with decreasing opening width. Based on these results, a novel InP/InGaAs heterojunction bipolar transistor (HBT) structure with extrinsic base laterally overgrown on SiO₂ is proposed. The device behaviors of the laterally regrown-base HBT prototypes are demonstrated.     

MOCVD growth of GaN on Si(1 1 1) substrates using an ALD-grown Al2O3 interlayer

GaN thin films have been grown on Si(1 1 1) substrates using an atomic layer deposition (ALD)-grown Al₂O₃ interlayer. This thin Al₂O₃ layer reduces strain in the subsequent GaN layer, leading to lower defect densities and improved material quality compared to GaN thin films grown by the same process on bare Si. XRD ω-scans showed a full width at half maximum (FWHM) of 549 arcsec for GaN grown on bare Si and a FWHM as low as 378 arcsec for GaN grown on Si using the ALD-grown Al₂O₃ interlayer. Raman spectroscopy was used to study the strain in these films in more detail, with the shift of the E₂(high) mode showing a clear dependence of strain on Al₂O₃ interlayer thickness. This dependence of strain on Al₂O₃ thickness was also observed via the redshift of the near bandedge emission in room temperature photoluminescence (RT-PL) spectroscopy. The reduction in strain results in a significant reduction in both crack density and screw dislocation density compared to similar films grown on bare Si. Screw dislocation density of the films grown on Al₂O₃/Si substrates approaches that of typical GaN layers on sapphire. This work shows great promise for the use of oxide interlayers for growth of GaN-based LEDs on Si.     

Growth of high quality a-plane GaN epi-layer on r-plane sapphire substrates with optimization of multi-buffer layer

Nonpolar (1 1–2 0) a-plane GaN films have been grown using the multi-buffer layer technique on (1–1 0 2) r-plane sapphire substrates. In order to obtain epitaxial a-plane GaN films, optimized growth condition of the multi-buffer layer was investigated using atomic force microscopy, high resolution X-ray diffraction, and transmission electron microscopy measurements. The experimental results showed that the growth conditions of nucleation layer and three-dimensional growth layer significantly affect the crystal quality of subsequently grown a-plane GaN films. At the optimized growth conditions, omega full-width at half maximum values of (11–20) X-ray rocking curve along c- and m-axes were 430 and 530 arcsec, respectively. From the results of transmission electron microscopy, it was suggested that the high crystal quality of the a-plane GaN film can be obtained from dislocation bending and annihilation by controlling of the island growth mode.     

Evolution of ordered one-dimensional and two-dimensional InAs/InP quantum dot arrays on patterned InP (1 0 0) and (3 1 1)B substrates by self-organized anisotropic strain engineering

The formation of ordered InAs/InP quantum dot (QD) arrays is demonstrated on patterned InP (1 0 0) and (3 1 1)B substrates by the concept of self-organized anisotropic strain engineering in chemical beam epitaxy (CBE). On shallow- and deep stripe-patterned InP (1 0 0) substrates, depending on the stripe orientation, the linear one-dimensional InAs QD arrays are rotated away from their natural direction due to the presence of vicinal stepped sidewall planes modifying the self-organization process, coexisting with QD free steep side facets on the deep-patterned substrates. On shallow- and deep-patterned InP (3 1 1)B substrates only QD free side facets form with flat top and bottom areas, not affecting the natural ordering of the two-dimensional InAs QD arrays. On the deep-patterned substrates a row of dense QDs forms on top along the side facets due to their slow-growing behavior. The optical properties of the QD arrays on the patterned substrates are not degraded compared to those of arrays formed on planar substrates for both InP (1 0 0) and (3 1 1)B substrates showing the potential of self-organized anisotropic strain engineering combined with step engineering for the creation of advanced complex QD arrays and networks.     

The photoluminescence of ZnO thin films grown on Si (1 0 0) substrate by plasma-enhanced chemical vapor deposition

High-quality ZnO thin films have been grown on a Si(1 0 0) substrate by plasma-enhanced chemical vapor deposition (PECVD) using a zinc organic source (Zn(C₂H₅)₂) and carbon dioxide (CO₂) gas mixtures at a temperature of 180°C. A strong free exciton emission with a weak defect-band emission in the visible region is observed. The characteristics of photoluminescence (PL) of ZnO, as well as the exciton absorption peak in the absorption spectra, are closely related to the gas flow rate ratio of Zn(C₂H₅)₂ to CO₂. Full-widths at half-maximum of the free exciton emission as narrow as 93.4 meV have been achieved. Based on the temperature dependence of the PL spectra from 83 to 383 K, the exciton binding energy and the transition energy of free excitons at 0 K were estimated to be 59.4 meV and 3.36 eV, respectively.     

Polar dependence of impurity incorporation and yellow luminescence in GaN films grown by metal-organic chemical vapor deposition

We have investigated the unintentional impurities, oxygen and carbon, in GaN films grown on c-plane, r-plane as well as m-plane sapphire by metal-organic chemical vapor deposition. The GaN layer was analyzed by secondary ion mass spectroscopy. The different trend of the incorporation of oxygen and carbon has been explained in the polar (0 0 0 1), nonpolar (1 1 2¯ 0) and semipolar (1 1 2¯ 2) GaN by a combination of the atom bonding structure and the origin direction of the impurities. Furthermore, it has been found that there is a stronger yellow luminescence (YL) in GaN with higher concentration of carbon, suggesting that C-involved defects are originally responsible for the YL.     

Selective area growth of GaN microstructures on patterned (1 1 1) and (0 0 1) Si substrates

Selective MOVPE growth of GaN microstructure on silicon substrates has been investigated using SiO₂ mask having circular or stripe window. In case of (0 0 1)substrate, grooves with (1 1 1) facets at the sides were made by using the etching anisotropy of a KOH solution. On the (1 1 1) facets of patterned silicon substrate (or on the as opened window region of (1 1 1) substrate), growth of wurtzite GaN was performed, of which the c-axis is oriented along the 1 1 1 axis of silicon. The photoluminescence and X-ray diffraction analysis were performed to characterize the single crystal to reveal the effect of the growth conditions of the intermediated layer and the microstructure.     

Subtle interplay between polytypism and preferred growth direction alignment in GaN nanorods non-catalytically grown on Si(1 1 1) substrates by using hydride vapor phase epitaxy

GaN nanorods were grown on Si(1 1 1) substrates by using hydride vapor phase epitaxy, and the crystallographic characteristics associated with their preferred growth directions were investigated by utilizing synchrotron X-ray reciprocal space mapping in a grazing incidence geometry and scanning electron microscopy. Crystallographic analysis reveals that the nanorods containing both wurtzite and zinc blende phase tend to have narrower distribution of the preferred growth directions than those containing only wurtzite phase. This tendency is partly attributed to the subtle interplay between polytypism and the preferred growth directions of GaN nanorods.     

Structural,electrical and optical properties of SnO2 films deposited on Y-stabilized ZrO2 (1 0 0) substrates by MOCVD

SnO₂ films have been deposited on Y-stabilized ZrO₂ (YSZ) (1 0 0) substrates at different substrate temperatures (500–800 °C) by metalorganic chemical vapor deposition (MOCVD). Structural, electrical and optical properties of the films have been investigated. The films deposited at 500 and 600 °C are epitaxial SnO₂ films with orthorhombic columbite structure, and the HRTEM analysis shows a clear epitaxial relationship of columbite SnO₂(1 0 0)||YSZ(1 0 0). The films deposited at 700 and 800 °C have mixed-phase structures of rutile and columbite SnO₂. The carrier concentration of the films is in the range from 1.15×10¹⁹ to 2.68×10¹⁹ cm⁻³, and the resistivity is from 2.48×10⁻² to 1.16×10⁻² Ω cm. The absolute average transmittance of the films in the visible range exceeds 90%. The band gap of the obtained SnO₂ films is about 3.75–3.87 eV.     

Epitaxial growth of GdN on silicon substrate using an AlN buffer layer

We report on the epitaxial growth of the intrinsic ferromagnetic semiconductor GdN on Si (1 1 1) substrates buffered by a thick AlN layer, forming a heteroepitaxial system with promise for spintronics. Growth is achieved by depositing Gd in the presence of unactivated N₂ gas, demonstrating a reactivity at the surface that is sufficient to grow near stoichiometric GdN only when the N₂:Gd flux ratio is at least 100. Reflection high-energy electron diffraction and X-ray diffraction show fully (1 1 1)-oriented epitaxial GdN films. The epitaxial quality of the films is assessed by Rutherford backscattering spectroscopy carried out in random and channelling conditions. Magnetic measurements exhibit a Curie temperature at 65 K and saturation magnetisation of 7 μ_B/Gd in agreement with previous bulk and thin-film data. Hall effect and resistance data establish that the films are heavily doped semiconductors, suggesting that up to 1% of the N sites are vacant.     

Characterization of bulk GaN crystals grown from solution at near atmospheric pressure

The properties of GaN crystals grown from solution at temperatures ranging from 780 to 810 °C and near atmospheric pressure ∼0.14 MPa, have been investigated using low temperature X-band (∼9.5 GHz) electron paramagnetic resonance spectroscopy, micro-Raman spectroscopy, photoluminescense spectroscopy, and photoluminescence imaging. Our samples are spontaneously nucleated thin platelets of approximate dimensions of 2×2×0.025 mm³, or samples grown on both polycrystalline and single crystal HVPE large-area (∼3×8×0.5 mm³) seeds. Electron paramagnetic resonance spectra consists of a single Lorentzian line with axial symmetry about the c-axis, with approximate g-values, g_∥=1.951 and g_⊥=1.948 and a peak-to-peak linewidth of∼4.0 G. This resonance has been previously assigned to shallow impurity donors/conduction electrons in GaN and attributed to Si- and/or O impurities. Room temperature photoluminescence and photoluminescence imaging data from both Ga- and N-faces show different dominant emission bands, suggesting different incorporation of impurities and/or native defects. Raman scattering and X-ray diffraction show moderate to good crystalline quality.     

Growth of height-controlled InGaN quantum dots on GaN

InGaN height-controlled quantum dots (HCQDs) were grown by alternately depositing In_0.4Ga_0.6N QD and In_0.1Ga_0.9N spacer layers on a seed In_0.4Ga_0.6N QD layer. Structural and optical studies showed that the height of the InGaN QDs was controlled by the deposition cycle of In_0.4Ga_0.6N/In_0.1Ga_0.9N layers. Photoluminescence studies showed that the In_0.4Ga_0.6N HCQDs provided deep potential wells and the piezoelectric field-induced quantum-confined Stark effect was negligibly small. These phenomena are attributed to variation in quantum confinement energy in the electronically coupled InGaN HCQDs providing deep potential wells.     

Influence of AlGaN/GaN/InGaN superlattice on the characteristics of LEDs grown by metalorganic chemical vapor deposition

This study examined the influence of strain-compensated triple AlGaN/GaN/InGaN superlattice structures (SLs) in n-GaN on the structural, electrical and optical characteristics of LEDs by analyzing the etch pits density (EPD), stress measurement, high-resolution X-ray diffraction (HRXRD), sheet resistance, photoluminescence (PL) and light–current–voltage (L–I–V). EPD, stress measurement and HRXRD studies showed that the insertion of AlGaN/GaN/InGaN SLs during the growth of n-GaN effectively distributed and compensated for the strong compressive stress, and decreased the dislocation density in n-GaN. The operating voltage at 20 mA for the LEDs grown with SLs decreased to 3.18 V from 3.4 V for the LEDs grown without SLs. In addition, a decrease in the spectral blue shift compared to the LEDs grown without SLs was observed in the LEDs grown with the SLs.     

Transmission electron microscopy study of an AlN nucleation layer for the growth of GaN on a 7-degree off-oriented (0 0 1) Si substrate by metalorganic vapor phase epitaxy

We have investigated the morphology of the high-temperature-grown AlN nucleation layer and its role in the early stage of GaN growth, by means of transmission electron microscopy. The nitride was selectively grown on a 7-degree off-oriented (0 0 1) patterned Si substrate by metalorganic vapor phase epitaxy. AlN was deposited on the inclined unmasked (1 1 1) facet in the form of islands. The size of the islands varied along the slope, which is attributable to the diffusion of the growth species in the vapor phase. The GaN nucleation occurred at the region where rounded AlN islands formed densely. The threading dislocations were observed to generate in the GaN nucleated region.     

Characterization of polycrystalline GaN grown on silica glass substrates

The structural, optical, and electrical properties of GaN films grown on silica glass substrate by metalorganic chemical vapor deposition were studied. X-ray diffraction showed that the films were grown in hexagonal structure with a predominant (0 0 0 2) peak. A broad and strong band-edge emission and very weak yellow luminescence in photoluminescence (PL) spectra were observed. And the temperature dependence of the PL spectra was extensively studied. The thermal quenching activation energy was found to be very close to the donor activation energy determined from the temperature dependence of the carrier concentration. Longitudinal optical phonons were found to be responsible for the PL broadening above 100 K.