Flow injection analysis for residual chlorine using Pb(II) ion-selective electrode detector

A simple flow injection analysis (FIA) system for residual chlorine in tap water has been developed by using a Pb(II) ion-selective electrode (ISE) detector. The method is based on a specific response of the Pb(II)-ISE to residual chlorine. The FIA system consists of a millivolt meter, a peristaltic pump, a Pb(II)-ISE detector and a recorder. A linear working curve between peak height and concentration of residual chlorine was obtained from 0.1 to 1 mg l(-1) for the developed FIA system. The relative standard deviation for repeated injections of a 0.2 mg l(-1) residual chlorine sample was 2%. The regression line and its correlation factor between the conventional o-tolidine colorimetric method and the present method were Y=0.75X+0.17 and 0.967, respectively, for this determination.     

Flow injection analysis for calcium in serum,water and waste waters by spectrophotometry and by ion-selective electrode

The Flow Injection technique is shown to provide fast, reliable and sensitive methods for the determination of calcium in various aqueous as well as serum samples; spectrophotometric or potentiometric detection can be used. At sampling rates of 100–110 samples per hour, with 30-μl sample injections, high reproducibility of measurement and low reagent consumption are achieved in both methods. In the spectrophotometric method, the analytical readout is available within 12 s after sample injection at a total reagent consumption of 0.75 ml per analysis. The potentiometric measurement of the calcium activity in serum is placed on a reliable basis by alternating measurements of serum samples and aqueous standards without incurring any non-reproducible changes in potential between aqueous and serum solutions. This permits the simultaneous determination of pH and pCa, the analytical readout being available within XXX s of sample injection. The good agreement between the results obtained with the Flow Injection method and those attained by atomic absorption and EDTA titrations as well as pCa stat-measurements show that the new methods are potentially suitable for routine analysis.     

Flow injection determination of bromide ion in a developer using bromide ion-selective electrode detector

A potentiometric flow injection determination method for bromide ion in a developer was proposed, by utilizing a flow-through type bromide ion-selective electrode detector. The sensing membrane of the electrode was Ag(2)S-AgBr membrane. The response of the electrode detector as a peak-shape signal was obtained for injected bromide ion in a developer. A linear relationship was found to exist between peak height and the concentration of the bromide ion in a developer in a concentration range from 1.0x10(-3) to 1.0x10(-2) mol l(-1). The relative standard deviation for 10 injections of a 6x10(-3) mol l(-1) bromide ion in a developer was 1.3% and the sampling rate was ca 17-20 samples h(-1). The present method was free from the interference of an organic reducing reagent, an organic substance in a developer sample solution for the determination of bromide ion in a developer.     

Flow injection analysis with tubular membrane ion-selective electrode and coated wires for buspirone hydrochloride

New Plastic membrane ion-selective electrode for buspirone hydrochloride based on buspironium tetraphenylborate was prepared. The electrode exhibited mean slope of calibration graph of 58.4 mV per decade of BusCl concentration at 25 degrees C. The electrode can be used within the concentration range 6.3 x 10(-5) - 10(-2) M BusCl at a pH range of 2.5-7.0. The standard electrode potentials were determined at different temperatures and used to calculate the isothermal temperature coefficient of the electrode, amounting to 0.00056 V degrees C(-1). The electrode showed a very good selectivity for BusCl with respect to a number of inorganic cations, sugars and amino acids. The electrode was applied to the potentiometric determination of the buspirone ion and its pharmaceutical preparation under batch and flow injection conditions. Also, buspirone was determined by conductimetric titrations. Graphite rod, copper and silver coated wire electrodes were prepared and characterized as sensors for the drug under investigation.     

Flow injection determination of iodide ion in a photographic developing solution using iodide ion-selective electrode detector

A potentiometric flow injection determination method for iodide ion in a photographic developing solution was proposed by utilizing a flow-through type iodide ion-selective electrode detector. The sensing membrane of the electrode was Ag₂S–AgI membrane. The response of the electrode detector as a peak-shape signal was obtained for injected iodide ion in a photographic developing solution. A linear relationship in the subnernstian zone was found to exist between peak height and the concentration of the iodide ion in a photographic developing solution in a concentration range from 0 to 6.0×10⁻⁵ mol l⁻¹. The relative standard deviation for ten injections of 2×10⁻⁵ mol l⁻¹ iodide ion in a photographic developing solution was 0.96% and the sampling rate was approximately 12–13 samples h⁻¹. The iodide ion could be determined under coexisting of an organic reducing reagent and inorganic electrolytes of high concentration in a photographic developing solution sample solution by the present method.     

Flow injection analysis of high chloride levels in electroplating baths using on-line dialysis and potentiometric detection

A method for the flow injection analysis (FIA) of high concentrations of chloride in electroplating baths using potentiometric detection is proposed. The system includes a unit of dialysis to promote dilution of samples and a tubular electrode with an homogeneous crystalline membrane as detector. The system was optimized in order to analyse samples within a broad range of concentrations and at high levels of chloride, thereby making pretreatment of the samples unnecessary. It results in a simple manifold applicable over the 4.0×10^–2 and 3.0 mol L^–1 range with a throughput of about 30 samples/h. Seven different plating bath samples were analysed by the proposed method and the quality of the results compared with those obtained by the conventional procedure. Satisfactory agreement was observed.     

Stripping analysis of heavy metals in tap water using the bismuth film electrode

A commercially available screen-printed carbon electrode coated with an ex situ deposited bismuth film (BiSPCE) has been applied to the determination of Pb(II) and Zn(II) ions in tap water (Barcelona water distribution network) by means of stripping voltammetry (SV) and stripping chronopotentiometry (SCP). A good reproducibility of the measurements and a satisfactory agreement between SV and SCP data were observed for both heavy metal ions. Although, in principle, the procedure could be also suited to the determination of Cd(II), this species was not detected. The results were also consistent with the routine ICP-OES measurements of the water distribution company, thus confirming the potential usefulness of such BiSPCE disposable devices for the analysis of heavy metals in natural waters.      

Flow injection potentiometric detection of trimethylamine in seafood using tungsten oxide electrode

A simple flow injection gas/diffusion method for the determination of trimethylamine (TMA) in seafood with potentiometric detection using tungsten oxide electrode has been developed. The method is based on the diffusion of TMA through a PTFE membrane from a sodium hydroxide donor stream to a phosphate buffer acceptor stream. The TMA in the acceptor stream passes through an electrochemical flow cell containing a tungsten oxide wire and a silver/silver chloride electrode, where TMA was sensitively detected. The parameters affecting the sensitivity of the electrode such as sodium hydroxide concentration, buffer concentration, pH, flow rate and injected volume were studied in details. The electrode response was linear in the concentration range from 1 to 10 μg ml⁻¹ TMA with a correlation coefficient (R²) of 0.991 and a detection limit of 0.05 μg ml⁻¹ TMA. The intra- and inter-days precision (R.S.D.) was found to be, respectively, 1.20 and 1.6% (n=6). The method was applied to the determination of TMA in fish tissue and recoveries of 99-100% were obtained for fish extracts. Results were in close agreement with those obtained by the existing classical official method. Common interference from those species that can diffuse through the membrane were removed by the addition of formaldehyde to the seafood extract. The method is simple, feasible with satisfactory accuracy and precision and thus, could be used for monitoring seafood quality with a sampling rate of 20±2 sample h⁻¹.     

Enzymatic determination of urea in undiluted whole blood by flow injection analysis using an ammonium ion-selective electrode

A flow-injection system is described for the assay of urea in undiluted whole blood. Urea is quantified by means of an ammonium ion-selective electrode covered with a membrane with covalently immobilized urease. The enzymatically generated ammonium ion is directly related to the urea concentration. Interference from potassium is reduced by adjusting the potassium ion concentration in the carrier stream and in the aqueous calibration solutions to 4.0 mM; it can be eliminated by measuring the potassium ion concentration in the sample separately and applying a mathematical correction for the K⁺ contribution to the signal. The linear measuring range is 1–40 mM urea, with an injection frequency of 40 h^?1 and a standard deviation of 1% for whole blood samples. The result of the measurement is obtained within 25 s from the time of injection. Vatiations in the hematocrit level of the sample have no effect on the measurement. The results obtained by the flow-injection method are in excellent agreement with those found routinely at a local hospital. The sensor is stable for more than 25 days.     

Flow injection amperometric detection of ascorbic acid using a Prussian Blue film-modified electrode

The PB film-modified electrode was used as an amperometric detector for flow injection analysis of ascorbic acid. The modified electrode detector showed good sensitivity, stability and reproducibility. The calibration curve for ascorbic acid was linear over the concentration range from 5.0x10(-6) to 1.0x10(-3) mol l(-1) with a slope of 19.9 mA mol(-1) per litre and a correlation coefficient of 0.999. The detection limit of this method was 2.49x10(-6) mol l(-1). The relative standard deviation of six replicate injections of 2.5x10(-4) mol l(-1) ascorbic acid was 2.5%. The results obtained for ascorbic acid determination in pharmaceutical products are in good agreement with those obtained by using the procedure involving the reaction between triiodide and ascorbic acid.     

Flow injection analysis with detection at mercury drop electrode in the presence of surfactants

The surfactant presence in a sample may cause distortion of the flow injection peak obtained with amperometric detection at a mercury drop electrode. Distortion depends on detection parameters and flow system operating parameters and in some cases it may be eliminated by their careful optimization. Introduction of fumed silica into the carrier solution allows the dynamic removal of surfactant during the sample passage through the mixing coil. In the case of higher surfactant concentration in the sample, addition of fumed silica directly to the sample may be effective. Examples with amperometric detection as well as anodic stripping and adsorptive stripping voltammetric detection are described.     

The fluoride ion-selective electrode in flow injection analysis : Part 3. Applications

Flow-injection potentiometry with a combination fluoride-selective electrode is used to determine fluoride in tap water, beverages and urine. Excellent sensitivity (down to 1 μg l^?1) and long-term stability are obtained, with a sample throughput of 30–40 h^?1, based on triplicate injections at 120 h^?1. The commonly used buffer TISAB-III is unsuitable for the analysis of undiluted tea and urine samples. The application of a modified citrate-containing TISAB overcomes interferences caused by high natural ionic strength and avoids complexation of fluoride. Recoveries after spiking tap water, tea and urine with fluoride concentration ranging from 0.01 to 1 mg l^?1 are in the range 91–106%. The equipment used provides a flexible system allowing fast changes between different buffers and carrier streams depending on the samples presented.     

Fluoride ion-selective electrode in flow injection analysis : Part 2. Interference Studies

The influence of the sample composition on the response characteristics of the fluoride ion-selective electrode in flow injection analysis is described. Sample parameters such as ionic strength, viscosity and pH affect the response time of the electrode and cause transient signals when limiting values are exceeded. The respective limiting values depend on the total ionic-strength adjustment buffer (TISAB) used and these interferences can be minimized by proper choice of the TISAB. The complex formation of fluoride by several elements in the presence of TISAB containing CDTA is discussed. Aluminium and magnesium were found to interfere when present at levels above 1 and 100 mg l^?1, respectively. The signal decrease in the presence of iron, calcium and silicon can be attributed to ionic strength effects rather than complexation. Provided that the ionic strength is taken into account and corrected for, no influence occurs even in the presence of 0.5, 2 and 5% of iron, calcium and silicon, respectively.     

Interference measurements in the potentiometric determination of chloride at ppb level using an ion-selective electrode

Detailed investigations on the interference of Br⁻, I⁻, S²⁻ and nitrogen-based pH adjustors over the chloride estimations at ppb level were carried out by differential potential measurement technique using an ion-selective electrode. The trend in the limiting interference concentrations were found to be not in accordance with the solubility product considerations alone. The presence of excess free amine/ammonia affected the stability of the measurement because of possible formation of the Ag—amine complex. The slope of the chloride calibration ranged from 0.01 to 0.015 mV per ppb, depending upon the medium.     

The determination of lead in water and sediment samples using a lead ion-selective electrode

Lead concentrations in water and sediment samples near a stationary metal emission source were determined using the lead ion-selective electrode. These results were then verified by use of atomic absorption spectrophotometric methods. Samples were collected at three strategic sites near a local lead company in Southeast Houston, Texas. Accumulated rain water and sediment (soil deep down core) were analyzed in order to estimate lead concentration as a function of depth. Data indicate that the level of lead concentrations in both surface water and water extracted from the sediments exceed the limits for drinking water as established by the Environmental Protection Agency. The lead concentrations of the soil samples were higher in most cases when compared with various soils in the United States. The highest concentrations of lead were found in surface water samples.     

Flow injection analysis of potassium using an all-solid-state potassium-selective electrode as a detector

The concentration of potassium was determined by a combination of flow injection analysis (FIA) with an all-solid-state potassium sensor detection. The all-solid-state potassium-selective electrode possessing long-term potential stability was fabricated by coating an electroactive polypyrrole/poly(4-styrenesulfonate) film electrode with a plasticized poly(vinyl chloride) membrane containing valinomycin. The simple FIA system developed in this laboratory demonstrated sensitivity identical to that in the batch system and achieved considerably rapid assay (150 samples h⁻¹). Analyses of soy sauce and control serum samples by this FIA system yielded results in good agreement with those obtained by conventional measurements.     

The fluoride ion-selective electrode in flow injection analysis: Part 1. General Methodology

A simple flow-injection system for determination of traces of fluoride by means of the fluoride-selective electrode is presented. A comparison of several flow-cell arrangements confirmed the advantages of a well-jet design. Systematic investigations of the parameters affecting response times (i.e., polishing procedure, flow rate, carrier composition) established the optimal experimental conditions for measurements down to 1 μg l^?1 fluoride. Calibration plots in the lower μg l^?1 range were neither Nernstein nor linear, but good precision (0.5–5%) was obtained even when the potential differences for concentration steps of one decade were as small as 3 mV.     

Sequential injection analysis of chloride and nitrate in waters with improved accuracy using potentiometric detection

Accurate simultaneous analysis of different anionic species using ion-selective electrodes (ISEs) can be achieved even for non-specific sensors by resorting to an ordinary least squares multiple regression in the vicinity of the predicted concentrations. In this work the potentialities of this approach are evidenced by the determination of nitrate and chloride in synthetic and real water samples in which chloride concentration was significantly higher than nitrate. An AgCl/Ag₂S electrode based on a homogeneous crystalline membrane together with a PVC electrode based on tert-octylammonium bromide dissolved in dibutylphthalate were used as potentiometric detectors for chloride and nitrate, respectively. For the implementation of the procedure, an automatic system based on sequential injection analysis was used. The results obtained by the standard addition method were biased for low concentrations of nitrate and were dependant on the relative proportion of NO₃⁻/Cl⁻. The results obtained by the proposed methodology for chloride determination were slightly better when compared to those obtained by the standard addition method. In relation to nitrate determination, the proposed methodology yielded values with a relative root mean square error of prediction (RRMSEP) of 2.8%, while for standard addition calibration, mean error values were approximately 12.1%.