Strain hardening behavior of polymer blends with fibril morphology

We investigate the rheological behavior of the polymer blends with fibril morphology, with special focus on the effect of fibril morphology on the extensional properties under uniaxial extension. We add a small amount of the dispersed phase to the matrix, and control the blend morphology by changing the viscosity ratio. When the fibril morphology is maintained, the blend shows not only a significant increase of the extensional viscosity but the strain hardening behavior. The extensional viscosity increases depending on the aspect ratio of the fibers, while the strain hardening behavior originates from the restricted stretching of deformable fibers, which has been confirmed theoretically by introducing the concept of rigidity of the fiber. It suggests a way to induce the strain hardening behavior by introducing deformable fibrils into the matrix, that is, by the design of polymer blends with a small amount of dispersed phase such that the fibril structure is maintained.     

The effect of pre-shear on the extensional rheology of wormlike micelle solutions

The effect of initial microstructural deformation, alignment, and morphology on the response of wormlike micelle solutions in transient uniaxial extensional flows is investigated using a pre-shear device attached to a filament stretching rheometer. In filament stretching experiments, increasing the strength and the duration of the pre-shear just before stretch is found to delay the onset of strain hardening. In these experiments, the wormlike micelle solution filaments fail through a rupture near the axial midplane. The value of the elastic tensile stress at rupture is found to decrease with increasing pre-shear rate and duration. The most dramatic effects are observed at shear rates for which shear banding has been independently observed. The reduction in the strain hardening suggests that pre-shear before filament stretching might break down the wormlike micelles reducing their size before stretch. Strain hardening is also observed in capillary breakup rheometry experiments; however, the pre-sheared wormlike micelle solutions strain harden faster, achieve larger steady-state extensional viscosities and an increase in the extensional relaxation time with increasing shear rate and duration. The difference between the response of the wormlike micelles in filament stretching and capillary breakup experiments demonstrates the sensitivity of these self-assembling micelle networks to pre-conditioning.     

Review of the entry flow problem: Experimental and numerical

This paper is concerned with a review of both experimental and numerical studies of axisymmetric and planar entry flows which have been considered as test problems for the numerical simulation of viscoelastic fluids. The test of the method is usually based upon whether the numerical model predicts vortices in the entry corners. However, it is not clear as to whether one should observe vortices for all viscoelastic fluids. Polyacrylamide solutions and Boger fluids exhibit vortices in axisymmetric flow and the size of the vortex does increase with fluid elasticity. However, the vortex is nearly suppressed in planar entry flow. On the other hand, not all polymer melts are found to exhibit vortices in either axisymmetric or planar entry flow. It is our belief that the origin of vortices is not related to the elasticity based on shear flow propertes but to the behavior of the transient extensional viscosity. Certain polymer melts such as low density polyethylene exhibit vortices in both planar and axisymmetric flow along with unbounded stress growth at the start up of extensional flow. It is believed that the constitutive equations used in the numerical simulation must reflect this extensional behavior if vortices are to be predicted. A review of the numerical simulations concerned with entry flow shows that there is considerable doubt about the accuracy of the predictions for most of the studies. Even for those where the numerical solution is thought to be accurate, the magnitude of the stream function associated with the vortices is usually very low. None of the differential models used to date predicts strain hardening extensional viscosity, but those which are thought to predict vortices do rise more rapidly to the steady-state extensional viscosity values with time. It is recommended that the search of test fluids be widened beyond polymer solutions as there may already exist a number of polymer melts which behave similarly to the predictions of existing constitutive equations.     

Rapid conical flows of viscoelastic solutions

Several examples of conical, stretching flows of viscoelastic solutions are described. Two cases are then examined in more detail, the rapidly stretching free jet and an internally pressurised sheet of liquid in which extension takes place in a circumferential direction.It is shown that both the stress and strain rate may readily be calculated at different positions, provided certain assumptions are made. The changes of extensional viscosity necessary to produce the specified flow geometries are then shown to be anomalous and inconsistent. If, however, a solid-like model based on the Green measure of strain is used, a more satisfactory interpretation of the behaviour is achieved.It is emphasised that these are high-speed, high Deborah number flows and that such a flow pattern is not a general one.An example is also given in which the stretching of rubber is shown to be consistent with the same solid-like model, and values of the extensional moduli of elasticity are quoted for both liquids and rubber.     

Surface tension driven jet break up of strain-hardening polymer solutions

Experimental studies attempting to ascertain the influence of viscoelasticity on the atomization of polymer solution are often hindered by the inability to decouple the effect of shear thinning from the effect of extensional hardening. Here, the influence of viscoelasticity on the jet break up of a series of non-shear-thinning viscoelastic fluids is quantified. Previous characterization using an opposed-nozzle rheometer identified the critical extensional rates for strain hardening of these model fluids. The strain hardening fluids exhibit a beads-on-string structure with reduction or elimination of satellite drops. Capillary instabilities grow on the filaments connecting the spheres and eventually break the filaments up into a string of very small drops about one order of magnitude smaller than the satellite drops formed by a Newtonian fluid with the same shear viscosity, surface tension, and density. These results confirm that strain hardening is the key rheological property in jet break up and that the critical extensional rate of a fluid is pertinent in determining the final characteristics of break up. Results suggest that the opposed-nozzle rheometer does probe extensional behavior in the range of extensional rates that are relevant to jet break up, providing a tool to roughly predict jet break up.     

The relevance of entry flow measurements for the estimation of extensional viscosity of polymer melts

The extensional viscosity of some flexible chain polymers and a thermotropic liquid crystalline polymer was measured in uniaxial extensional flow at constant extension rate. Power law functions were found for the dependence of the extensional viscosity at constant accumulated strain on strain rate. The stress growth curves were compared with measurements in axisymmetric entry flow, where both elongation and shear occur. The comparison showed that the values of the extensional viscosity calculated from the measurements in the entry flow correspond to the ones calculated from the viscosity growth measured in uniaxial elongation and averaged over extensional strain equal to what is accumulated on the fluid as it flows from the barrel into the capillary.     

Design of new HDPE/silica nanocomposite and its enhanced melt strength

Linear polymers are restricted to use in processes that involve severe extensional deformation, such as fiber spinning, film blowing, and thermoforming. To extend their applicability, the extensional properties of polymer melts should be enhanced such that strain hardening, which is defined as an increase in extensional viscosity under a large strain that deviates from the linear viscoelastic curve, is pronounced. In this study, a novel preparation method of linear polymer/inorganic nanocomposites was proposed with a main focus on enhanced melt strength. The design of molecular structure consists of three components—linear polymer, compatibilizer, and surface-modified particles. High-density polyethylene was used as a linear polymer while polyethylene grafted with maleic anhydride was used as a compatibilizer. Silica particles were synthesized and modified on their surfaces by 3-aminopropyltriethoxysilane. The strain hardening behavior of the surface-modified silica composites was pronounced. However, such a result was not observed for the composites of the same composition with pure-silica. In addition, the dispersion of the modified silica was much better than that of pure-silica.     

Suspensions of monodisperse spheres in polymer melts: particle size effects in extensional flow

Suspensions in polymeric, viscoelastic liquids have been studied in uniaxial extensional flow. The fibre wind-up technique has been used for this purpose. The effects of particle size and particle volume fraction have been investigated, using monodisperse, spherical particles. The results have been compared with shear flow data on the same materials. The values of the relative extensional viscosities at low stretching rates are in agreement with the relative shear viscosities and relative moduli. This indicates that hydrodynamic forces are stronger than the particle interaction forces. At larger strain rates strain hardening occurs; it is suppressed when particles are added. Small aggregating particles reduce the strain hardening more strongly than larger particles; strain hardening can even be totally eliminated. When further increasing the stretching rate, hydrodynamic effects dominate again and the effect of particle size effect on strain hardening disappears.     

Elongational flow and rheology of monodisperse polymers in solution

We describe the utilization of idealized stagnation point extensional flows, produced by opposed jets, for birefringence visualization of induced molecular strain and flow resistance measurements. We identify rheological changes associated with the coil---stretch transition which occurs beyond a critical strain-rate in elongational flow-fields. In dilute solutions of monodisperse atactic polystyrene, increases in extensional viscosity are observed as isolated molecules become stretched. The largest increases in extensional viscosity, however, are found only beyond a critical concentration and strain rate, and are associated with the stretching of transient networks of interacting molecules. These results parallel similar effects seen in porous media flow and capillary entrance experiments. We determine the molecular weight dependence of the critical concentration which scales as M^−0.55 in agreement with pairwise interaction of coils, but is much lower than conventional values of the critical polymer concentration, c^*. We believed that polydispersity may play an important role in the development of such transient networks, and in controlling the degradation behaviour during flow.     

A new look at extensional rheology of low-density polyethylene

The nonlinear rheology of three selected commercial low-density polyethylenes (LDPE) is measured in uniaxial extensional flow. The measurements are performed using three different devices including an extensional viscosity fixture (EVF), a homemade filament stretching rheometer (DTU-FSR) and a commercial filament stretching rheometer (VADER-1000). We show that the measurements from the EVF are limited by a maximum Hencky strain of 4, while the two filament stretching rheometers are able to probe the nonlinear behavior at larger Hencky strain values where the steady state is reached. With the capability of the filament stretching rheometers, we show that LDPEs with quite different linear viscoelastic properties can have very similar steady extensional viscosity. This points to the potential for independently controlling shear and extensional rheology in certain rate ranges.     

Filament stretching of carbon nanotube suspensions

This paper reports the application of a recently developed filament stretching protocol for the study of the extensional rheology of both treated and untreated carbon nanotubes (CNT) suspended within an epoxy resin. It was experimentally observed that filaments formed by treated and untreated CNT suspensions behaved differently after initial stretching. The filament thinning process of the base epoxy was consistent with a simple Newtonian fluid, whilst the filament of treated CNT suspensions also thinned in a Newtonian way but with an enhanced extensional viscosity. Filaments formed with untreated CNT suspensions behaved in a non-uniform way with local fluctuation in filament diameter, and it was not possible to obtain reliable extensional viscosity data. Irregularity of the untreated CNT filaments was consistent with coupled optical images, where spatial variation in CNT aggregate concentration was observed. In the case of treated CNT suspensions, the enhanced extensional viscosity was modelled in terms of the alignment of CNTs in the stretching direction, and the degree of alignment was subsequently estimated using a simple orientation model.     

Extensional rheology of concentrated poly(ethylene oxide) solutions

The shear and extensional rheology of three concentrated poly(ethylene oxide) solutions is examined. Shear theology including steady shear viscosity, normal stress difference and linear viscoelastic material functions all collapse onto master curves independent of concentration and temperature. Extensional flow experiments are performed in fiber spinning and opposed nozzles geometries. The concentration dependence of extensional behavior measured using both techniques is presented. The zero-shear viscosity and apparent extensional viscosities measured with both extensional rheometers exhibit a power law dependence with polymer concentration. Strain hardening in the fiber spinning device is found to be of similar magnitude for all test fluids, irrespective of strain rate. The opposed nozzle device measures an apparent extensional viscosity which is one order of magnitude smaller than the value determined with the fiber spinline device. This could be attributed to errors caused by shear, dynamic pressure, and the relatively small strains developed in the opposed nozzle device. This instrument cannot measure local kinematics or stresses, but averages these values over the non-homogenous flow field. These results show that it is not possible to measure the extensional viscosity of non-Newtonian and shear thinning fluids with this device. Fiber spin-line experiments are coupled with a momentum balance and constitutive model to predict stress growth and diameter profiles. A one-mode Giesekus model accurately captures the plateau values of steady and dynamic shear properties, but fails to capture the gradual shear thinning of viscosity. Giesekus model parameters determined from shear rheology are not capable of quantitatively predicting fiber spinline kinematics. However, model parameters fit to a single spinline experiment accurately predict stress growth behavior for different applied spinline tensions.     

Uniaxial extensional flow behavior of immiscible and compatibilized polypropylene/liquid crystalline polymer blends

In this work liquid crystalline polymer (LCP) and thermoplastic (TP) blends with and without compatibilizer were studied with respect to their elongational flow behavior, under uniaxial extensional flow. This knowledge is important because in processes involving dominantly extensional deformations, like the case of the formation of the LCP fibrillation, transient extensional flow properties become more important than transient or steady-shear properties. In systems characterized by disperse phase morphologies (10 and 20 wt%) the LCP acts as a plasticizer, decreasing the viscosity of the system and increasing its durability with respect to that of the matrix. On the other hand, for a system in which a co-continuous morphology is present (40 wt% LCP) fibrils and droplets deformation occurs simultaneously, leading to a much higher strain hardening and durability. Moreover, the addition of compatibilizers to the blends gives rise to an increase of the strain hardening and to a decrease of the durability, which is in accordance with the mechanical properties, namely a higher Young’s modulus and lower elongation at break, in comparison with noncompatibilized systems.     

Effect of vinyl acetate content and silicate loading on EVA nanocomposites under shear and extensional flow

In this study, three EVAs (ethylene-vinyl acetate co-polymers) with different vinyl contents (VA) ranging from 9 wt% to 28 wt% (EVA9, EVA18 and EVA28) were melt blended with organo-clay to obtain polymer layered silicate nanocomposites. Filler intercalation and exfoliation were evidenced by X-ray diffraction. The melt state viscoelastic properties of EVA nanocomposites were studied to examine the influence of clay in altering the flow properties of these polymeric nanocomposites. The EVA18 and EVA28 nanocomposites exhibited remarkable difference in dynamic and steady shear properties compared to neat polymers. On the other hand, EVA9-5% nanocomposite did not exfoliate and exhibited rheological behaviour very similar to that of the neat polymer. Furthermore, the first normal stress difference was found to be dependent on the silicate loadings when measured at low shear stresses. The uniaxial extensional viscosity measurement indicated that the strain hardening was weaker in EVA nanocomposites compared to neat polymers. Environmental scanning electron (ESE)-microscopy elucidated a possible reason for reduced strain hardening in these systems.     

Investigation of the rheological properties of short glass fiber-filled polypropylene in extensional flow

The behavior of short glass fiber–polypropylene suspensions in extensional flow was investigated using three different commercial instruments: the SER wind-up drums geometry (Extensional Rheology System) with a strain-controlled rotational rheometer, a Meissner-type rheometer (RME), and the Rheotens. Results from uniaxial tensile testing have been compared with data previously obtained using a planar slit die with a hyperbolic entrance. The effect of three initial fiber orientations was investigated: planar random, fully aligned in the stretching flow direction and perpendicular to it. The elongational viscosity increased with fiber content and was larger for fibers initially oriented in the stretching direction. The behavior at low elongational rates showed differences among the various experimental setups, which are partly explained by preshearing history and nonhomogenous strain rates. However, at moderate and high rates, the results are comparable, and the behavior is strain thinning. Finally, a new constitutive equation for fibers suspended into a fluid obeying the Carreau model is used to predict the elongational viscosity, and the predictions are in good agreement with the experimental data.     

The rheology of polymer solution elastic strands in extensional flow

We apply micro-oscillatory cross-slot extensional flow to a semi-dilute poly(ethylene oxide) solution. Micro-particle image velocimetry (μPIV) is used to probe the real local flow field. Extreme flow perturbation is observed, where birefringent strands of extended polymer originate from the stagnation point. This coincides with a large increase in the extensional viscosity. The combination of stagnation point flow and μPIV enables us to investigate directly the stress and strain rates in the strand and so determine the true extensional viscosity of the localised strand alone. The Trouton ratio in the strand is found to be ~4000, amongst the highest values of Trouton ratio ever reported. Consideration of the flow in the exit channels surrounding the highly elastic strand suggests a maximum limit for the pressure drop across the device and the apparent extensional viscosity. This has implications for the understanding of high Deborah number extensional thinning reported in other stagnation point flow situations.     

Birefringence and stress growth in uniaxial extension of polymer solutions

Simultaneous measurements of extensional stresses and birefringence are rare, especially for polymer solutions. This paper reports such measurements using the filament stretch rheometer and a phase modulated birefringence system. Both the extensional viscosity and the birefringence increase monotonically with strain and reach a plateau. Estimates of this saturation value for birefringence, using Peterlin’s formula for birefringence of a fully extended polymer chain are in agreement with the experimental results. However, estimates of the saturation value of the extensional viscosity using Batchelor’s formula for suspensions of elongated fibres are much higher than observed. Reasons for the inability of the flow field to fully unravel the polymer chain are examined using published Brownian dynamics simulations. It is tentatively concluded that the polymer chain forms a folded structure. Such folded chains can exhibit saturation in birefringence even though the stress is less than that expected for a fully extended molecule.Simultaneous measurements of stress and birefringence during relaxation indicate that the birefringence decays much more slowly than the stress. The stress-birefringence data show a pronounced hysteresis as predicted by bead-rod models. The failure of the stress optic coefficient in strong flows is noted.Experiments were also performed wherein the strain was increased linearly with time, then held constant for a short period before being increased again. The response of the stress and birefringence in such experiments is dramatically different and can be traced to the different configurations obtained during stretching and relaxation. The results cast doubt on the appropriateness of pre-averaging the non-linear terms in constitutive equations.     

The effect of step-stretch parameters on capillary breakup extensional rheology (CaBER) measurements

Extensional rheometry has only recently been developed into a commercially available tool with the introduction of the capillary breakup extensional rheometer (CaBER). CaBER is currently being used to measure the transient extensional viscosity evolution of mid to low-viscosity viscoelastic fluids. The elegance of capillary breakup extensional experiments lies in the simplicity of the procedure. An initial step-stretch is applied to generate a fluid filament. What follows is a self-driven uniaxial extensional flow in which surface tension is balanced by the extensional stresses resulting from the capillary thinning of the liquid bridge. In this paper, we describe the results from a series of experiments in which the step-stretch parameters of final length, and the extension rate of the stretch were varied and their effects on the measured extensional viscosity and extensional relaxation time were recorded. To focus on the parameter effects, well-characterized surfactant wormlike micelle solutions, polymer solutions, and immiscible polymer blends were used to include a range of characteristic relaxation times and morphologies. Our experimental results demonstrate a strong dependence of extensional rheology on step-stretch conditions for both wormlike micelle solutions and immiscible polymer blends. Both the extensional viscosity and extensional relaxation time of the wormlike micelle solutions were found to decrease with increasing extension rate and strain of the step-stretch. For the case of the immiscible polymer blends, fast step-stretches were found to result in droplet deformation and an overshoot in the extensional viscosity which increased with increasing strain rates. Conversely, the polymer solutions tested were found to be insensitive to step-stretch parameters. In addition, numerical simulations were performed using the appropriate constitutive models to assist in both the interpretation of the CaBER results and the optimization of the experimental protocol. From our results, it is clear that any rheological results obtained using the CaBER technique must be properly considered in the context of the stretch parameters and the effects that preconditioning has on viscoelastic fluids.     

Dehnviskosität von Kautschukmischungen

It is shown that the extensional viscosity measured by uniaxial stretch may give useful information as to the processability of rubber compounds. A simple apparatus was constructed to measure this rheological property at constant rate of strain. The influence of rubber type, filler, aging, mastication and degree of crosslinking on the reduced stress is represented by diagrams. No steady-state extensional viscosity was obtained for highly filled rubber compounds. It was found that the flow behaviour of rubber compounds can be better characterized with an extensional rheometer than with a high-pressure capillary rheometer.

     

Mesoscopic dynamics of polymer chains in high strain rate extensional flows

We take a step towards accessing the physics of viscoelastic liquid breakup in high speed, high strain rate flows by performing Brownian dynamics computations of dilute uniaxial, equibiaxial, and ellipsoidal polymeric extensional flows. Our computational implementation of the bead-spring model, when tailored to the DNA molecule, consistently with recent works of Larson and co-workers, is shown: (a) to predict a coil-stretch transition at Deborah number De≈0.5, and (b) to reproduce the experimental longest relaxation time. Furthermore, after adapting the model parameters to represent the polyethylene oxide (PEO) chain (for M=10⁶ Da), we find it possible to reproduce our own experimental data of the longest relaxation time, the transient extensional viscosity of dilute solutions at small Deborah numbers, and a coil-stretch transition at Deborah number De≈0.5. Extended to large Deborah numbers, the model predicts that polymer stretching is controlled by: (a) the randomness of the initial conditions that, in combination with rapid kinematically imposed compression, lead to the formation of initially frozen chain-folds, and (b) the speed with which thermo-kinematic processes relax these folds. The slowest fold relaxation occurs during uniaxial extension. As expected, the introduction of stretching along a second direction enhances the efficiency of fold relaxation mechanisms. Even for Deborah numbers (based on the chain longest relaxation time) of the order of one thousand, there is a large variation in the time a polymer needs in order to extend fully, and the effects of Brownian motion cannot be ignored. The computed Trouton ratios and polymer contributions to the total stress as functions of Hencky strain provide information about the relative importance of elastic effects during polymeric liquid stretching. At high strain rates, the steady state elastic stresses increase linearly with the Deborah number, resembling at that stage an anisotropic Newtonian fluid (constant extensional viscosity).