La－Th－O系催化剂的结构与甲烷氧化偶联催化性能的关系

研究了Ｌａ－Ｔｈ－Ｏ二元氧化物的组成、结构及其对甲烷氧化偶联反应催化性能的影响；用ＸＲＤ、ＩＲ、ＸＰＳ、ＳＥＭ等方法对催化剂进行表征。Ｌａ－Ｔｈ－Ｏ系列催化剂随Ｌａ／Ｔｈ原子比的变化，可生成Ｌａ＿ｘＴｈ＿（１－ｘ）Ｏ＿（２－δ）固溶体。具有萤石结构的Ｌａ＿ｘＴｈ＿（１－ｘ）Ｏ＿（２－δ）是甲烷氢化偶联反应的主要活性相。     

Li—Ni—La—O系复合氧化物催化剂上甲烷氧化偶联的研究

考察了Ｌｉ－Ｎｉ－Ｌａ－Ｏ系催化剂的组成、结构及反应条件对甲烷氧化偶联反应活性的影响。在７８０℃、ＣＨ４：Ｏ２：Ｎ２＝２：１：７、空速１５０００ｈ＾－１时，Ｃ２烃收率可达２５．８％。ＸＲＤ、ＩＲ、ＸＰＳ及ＳＥＭ等的结构分析表明，在ＬｉＬａ１－ｘＮｉｘＯ２催化剂中，当０．１≤ｘ≤０．９时，该催化剂由ＬｉＮｉＯ２和Ｌａ２Ｎｉ１－ｙＬｉｙＯ４－λ两相组成，ｘ＜０．３时出现了ＬｉＬａＯ２相，Ｌａ２Ｎｉ１－     

含氧化镧的甲烷氧化偶联催化剂的一些特性

利用ＤＴＡ、ＴＰＤ－ＭＳ、ＸＲＤ、ＴＰＲ及ＴＰＳＲ－ＭＳ等手段对Ｌａ＿２Ｏ＿３和含Ｌａ＿２Ｏ＿３的甲烷氧化偶联催化剂进行了研究。实验发现含Ｌａ＿２Ｏ＿３的催化剂的一个特点是其容易吸水，此时，催化剂中除含Ｌａ＿２Ｏ＿３外，还有Ｌａ（ＯＨ）＿３及Ｌａ＿２Ｏ＿３ＣＯ＿２存在。ＴＰＲ及ＴＰＳＲ结果表明了催化剂的起始氢气还原温度与纯甲烷的程序升温反应开始温度的一致性，这说明催化剂的晶格氧参与了甲烷的活化过程。不同的氧化物由于其晶格氧的活性不同，因而其活化甲烷的温度不同。Ｌａ＿２Ｏ＿３中的晶格氧非常活泼，它在７３０℃时即可以与甲烷或与Ｈ＿２反应而本身被还原。甲烷和氧气共进料时的程序升温反应（ＴＰＳＲ－ＭＳ）表明甲烷氧化偶联反应中Ｃ＿２烃的选择性有一最佳温度范围。     

La2—xSrxNiO4上氧的TPD及其氧化活性

Ｌａ２－ｘＳｒｘＮｉＯ４上Ｏ２的ＴＰＤ研究表明，氧的脱附性能与催化剂结构中Ｎｉ＾２＾＋和Ｎｉ＾３＾＋的性质及含量有关。晶格氧直接参与了ＣＯ的氧化与甲烷的氧化偶联。     

钙钛矿型LaCoO3—δ和La1—xSrxCoO3—δ纳米粒子的XPS表征

采用ＸＰＳ等手段对ＬａＣｏＯ３－δ和Ｌａ１－ｘＳｒｘＣｏＯ３－δ纳米粒子进行了表征。结果显示,随ＬａＣｏＯ３－δ纳米粒子粒径的减小,一方面表面钴浓度增加,另一方面,表面ＣｏＯ键的离子性增强和表面氧空位浓度增加。此二者共同导致ＬａＣｏＯ３－δ对一氧化碳氧化的催化活性随其粒径减小而明显增大。ＬａＣｏＯ３－δ纳米粒子中镧被锶部分取代后,其表面结构发生了变化,并导致对一氧化碳氧化的催化活性显著提高     

含氧化镧的甲烷的氧化偶联催化剂的一些特性

利用ＤＴＡ、ＴＰＤ－ＭＳ、ＸＲＤ、ＴＰＲ及ＴＰＳＲ－ＭＳ等手段对Ｌａ２Ｏ３和含Ｌａ２Ｏ３的甲烷氧化偶联催化剂进行了研究。实验发现含Ｌａ２Ｏ３的催化剂的一个特点是其容易吸水，此时，催化剂中除含Ｌａ２Ｏ３外，还有Ｌａ（ＯＨ）３及Ｌａ２Ｏ３ＣＯ２存在。ＴＰＲ及ＴＰＳＲ结果表明了催化剂的起始氢气还原温度与纯甲烷的程序升温反应开始温度的致性，这说明催化剂的晶格氧参与了甲烷的活化过程。不同的氧化物由于其晶格氧     

甲烷氧化偶联制乙烯La2O3—BaO体系催化剂稳定性的研究

研究了甲烷氧化偶联制乙烯高选择性Ｌａ２Ｏ３－ＢａＯ体系催化剂的稳定性．在８００℃、ＣＨ４空速１００００ｈ－１、ＣＨ４／Ｏ２＝８．０～８．３的条件下，催化剂稳定运转了５００ｈ，ＣＨ４转化率和Ｃ２选择性分别为≥１８％和≥８０％．ＸＲＤ和ＸＰＳ分析表明，该催化剂物相稳定，表面Ｌａ／Ｂａ原子浓度之比随反应时间的增加而稍有增加，有利于催化剂活性和选择性的稳定．     

氧化镧催化剂上甲烷氧化偶联—不同制备方法的比较

本文研究了５种不同制法的Ｌａ＿２Ｏ＿３对甲烷氧化偶联的催化性能，其Ｃ＿２选择性和Ｃ＿２收率的相对顺序为：Ｌａ＿２Ｏ＿３（１）＞Ｌａ＿２Ｏ＿３（２）＞Ｌａ＿２Ｏ＿３（４）＞Ｌａ＿２Ｏ＿３（５）＞Ｌａ＿２Ｏ＿３（３）。并运用ＸＲＵ、ＸＰＳ、ＣＯ＿２－ＴＰＤ、ＮＨ＿３－ＴＰＤ和ＩＰＡ转化反应等技术分别对催化剂的体相结构和表面性质，表面酸碱性进行了测定。结果表明，由于制备方法的不同，导致了Ｌａ＿２Ｏ＿３晶体表面结构的差异，这是影响催化性能的主要原因。同时还发现，催化剂的活性和Ｃ＿２选择性与表面酸碱性存在着相依性，Ｌａ＿２Ｏ＿３表面的总碱位数与总酸位数的比值，与其催化性能有较好的直接对应关系。     

甲烷氧化偶联含锂多元复合氧化物催化剂的失活机理

对甲烷氧化偶联反应活性较高的多元复合氧化物催化剂（Ｌｉ－Ｔｉ－Ｌａ，Ｌｉ－Ｍｎ－Ｌａ，Ｌｉ－Ｎｉ－Ｌａ）的稳定性和失活机理进行了初步探讨，利用ＸＲＤ，ＩＲ，ＸＰＳ和Ｏ２－ＴＰＤ等方面对催化剂进行了表征，结果表明，催化剂在高温及反应气氛的作用下，表面锂的流失，使体相晶格中的锂向表面扩散，导致含锂活性相结构的分解（或部分分解），从而减少了体相相氧空位和生氧种的数量，降低了晶格氧的活动性，致使催化剂活必     

甲烷氧化偶联催化反应的特征

应用程序升温反应（ＴＰＲ）及质谱分析表征了ＣａＯ，Ｓｍ２Ｏ３，０．５－１０％Ｓｍ／ＣａＯ催化剂上的甲烷氧化偶联反应特性。谱图分析表明，在４００－１０００℃范围内，甲烷氧化偶联反应产物的变化呈现三个反应温度区域：（１）完全氧化区，反应主要为ＣＨ３·在催化剂表面完全氧化形成ＣＯｘ和Ｈ２：（２）偶联区，主要为ＣＨ３·的氧化和偶联竞争反应，Ｈ２谱线出现明显的低温峰；（３）氧耗尽区，反应为高温气相反应，产物     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Selective syntheses of 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones via temperature-dependent Rh(II)-carbenoid-mediated 2H-azirine-ring expansion

The Rh(II)-catalyzed reaction of 2-carbonyl-substituted 2H-azirines with ethyl 2-cyano-2-diazoacetate or 2-diazo-3,3,3-trifluoropropionate provides an easy access to 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones. These compounds can be selectively prepared from the same starting material using temperature as the only varied parameter. The 2-azabuta-1,3-diene intermediate, a common precursor for both heterocyclic products, isomerizes into 2H-1,3-oxazine under kinetic control, while 1H-pyrrol-3(2H)-one is the sole product of the reaction at elevated temperatures. According to DFT-calculations a one-atom oxazine ring contraction involving ring-opening to a 2-azabuta-1,3-diene intermediate, followed by a 1,5- and 1,2-prototropic shift leads to the consecutive formation of imidoylketene and azomethine ylide, which then further undergo cyclization to the pyrrole derivative.     

Copper catalyzed/mediated synthetic methodology for ebselen and related isoselenazolones

Scope of the copper catalyzed/mediated selenium-nitrogen coupling reaction has been studied for the synthesis of isoselenazolones. It is noticed that the 2-chloro, 2-bromo-, and 2-iodo-aryl amides substrates can be exploited in the selenium-nitrogen coupling reaction by employing 25-100 mol % of CuI/1,10-phenanthroline (L) and potassium carbonate as a base in DMF. Furthermore, electron rich 2-chloro-arylamides also underwent selenium-nitrogen coupling reaction to give biologically important selenium-nitrogen heterocycles. Also, copper-catalyzed selenium-nitrogen coupling reaction has been meticulously applied for the synthesis of diaryl diselenides having methoxy, amine, and amide functionality from respective aryl iodides in the presence of stoichiometric amount of succinimide as an external Se-N coupling partner.     

Knoevenagel condensation catalyzed by novel Nmm-based ionic liquids in water

A series of novel N-methyl morpholine (Nmm) based ionic liquids with 1,2-propanediol group were synthesized and used as catalysts for Knoevenagel condensation at room temperature in water. Under the effect of the catalyst, various aldehydes or aliphatic ketones could react with a wide range of activated methylene compounds well, including malononitrile, alkyl cyanoacetate, cyanoacetamide, β-diketone, barbituric acid, 2-arylacetonitrile and thiazolidinedione. Furthermore, most of the products could be separated just by filtrating and washing with water. Additionally, the catalyst is recyclable and applicable for the large-scale synthesis.     

Construction of polyheterocyclic spirotetrahydrothiophene derivatives via sulfa-Michael/aldol cascade reaction

A series of polyheterocyclic spirotetrahydrothiophene derivatives were obtained in moderate to excellent yields via a catalyst-free sulfa-Michael/aldol cascade reaction of chalcones 1 and commercially available 1,4-dithiane-2,5-diol 2 under mild conditions. We also present the first asymmetric sulfa-Michael/aldol cascade reaction of chalcones 1 and commercially available 1,4-dithiane-2,5-diol 2 with moderate to good enantioselectivities catalyzed by readily available chiral phase-transfer catalysts (PTCs).     

Suzuki-Miyaura reactions of the soluble guanylate cyclase inhibitor NS2028: a non-product specific route to C-8 substituted analogues

Both soluble guanylate cyclase (sGC) inhibitors ODQ 1 and NS2028 2 are synthesized via improved protocols. In the former case treating 3,4-dihydroquinoxalin-2(1H)-one oxime 8, which can be prepared in two steps from 1,2-benzenediamine, with 1,1′-carbonyldiimidazole (CDI) gives the dihydro-ODQ 10 that in the presence of KMnO₄ oxidises to give ODQ 1 in an overall yield of 46% starting from 1,2-benzenediamine. In the latter case, the synthesis affords NS2028 2 from 2-amino-4-bromophenol 3 in three steps with an overall yield of 85% and avoids the need for chromatography. Furthermore, Suzuki-Miyaura reaction conditions are described that enable the preparation of 8-aryl and 8-heteroaryl derivatives of NS2028 directly from NS2028 2. Finally, demethylation of the 8-(methoxyphenyl) substituted analogues afforded the 8-(hydroxyphenyl) derivatives 40-42. All new products are fully characterised.