稀土磷酸盐发光材料的微波合成

稀土磷酸盐发光材料的微波合成徐文国，田一光，刘淼，刘海堂，方光华，庞文琴（吉林大学化学系，环境科学系，长春，１３００２３）关键词微波合成，稀土磷酸盐，微晶玻璃，玻璃态，发光材料稀土磷酸盐发光材料的研究是当前材料科学的热门研究课题。它们一般通过高温固相...     

掺Er^3＋重金属氧氟硅酸盐玻璃的光谱性质与Judd—Ofelt理论分析

制备了掺Er^3 重金属氧氟硅酸盐玻璃，研究了玻璃的吸收光谱和荧光光谱性质，应用Judd-Ofelt理论计算了强度参数Ωt(t＝2，4，6)、Er^3 离子的振子强度、自发辐射跃迁几率、荧光分支比和辐射寿命等光谱参数。应用McCCumber理论，计算了能级^413/2→^4I15/2跃迁的受激发射截面。结果表明：掺Er^3 重金属氧氟硅酸盐玻璃具有较宽的荧光半高宽和较大的受激发射截面。对Er^3 离子在不同玻璃基质中带宽特性的比较发现，掺Er^3 重金属氧氟硅酸盐玻璃的带宽特性与碲酸盐和铋酸盐玻璃相当，大于磷酸盐、锗酸盐和硅酸盐玻璃。     

掺Er~(3+)重金属氧氟硅酸盐玻璃的光谱性质与Judd-Ofelt理论分析

制备了掺Er3+重金属氧氟硅酸盐玻璃,研究了玻璃的吸收光谱和荧光光谱性质,应用Judd Ofelt理论计算了强度参数Ωt(t=2,4,6)、Er3+离子的振子强度、自发辐射跃迁几率、荧光分支比和辐射寿命等光谱参数。应用McCumber理论,计算了能级4I13 2→4I15 2跃迁的受激发射截面。结果表明:掺Er3+重金属氧氟硅酸盐玻璃具有较宽的荧光半高宽和较大的受激发射截面。对Er3+离子在不同玻璃基质中带宽特性的比较发现,掺Er3+重金属氧氟硅酸盐玻璃的带宽特性与碲酸盐和铋酸盐玻璃相当,大于磷酸盐、锗酸盐和硅酸盐玻璃。     

掺铒TeO2-WO3玻璃光谱性能

研究了掺铒TeO2-WO3玻璃的吸收光谱和荧光光谱性质.根据吸收光谱,应用Judd-Ofelt理论计算得到了3个强度参数Ωt(t=2,4,6),分别为Ω2=5.38×10-20cm2,Ω4=1.78×10-20 cm2,Ω6=0.75×10-20cm2.Er3 离子在TeO2-WO3玻璃中的Ω6小于磷酸盐、氟磷酸盐中的Ω6,而大于锗酸盐、硅酸盐和碲酸盐玻璃中的Ω6,说明Er-O键在TeO2-WO3玻璃中的共价性大于磷酸盐、氟磷酸盐中Er-O键的共价性而小于锗酸盐、硅酸盐和碲酸盐玻璃中Er-O键的共价性.4I13/2→4I15/2荧光光谱表明Er3 的荧光半高宽(FWHM)为66 nm,荧光寿命为3.2 ms;应用McCumber理论计算了Er3 的峰值发射截面σe为8.0×10-21cm2.对Er3 在不同基质玻璃中光谱参数比较发现,TeO2-WO3玻璃的FWHM×σe乘积较大,说明其带宽特性较好.     

掺钕磷酸盐激光玻璃的工艺研究

选取磷酸盐系统作基质、Nd^3 作激活离子的激光玻璃作研究对象。通过对不同生产工艺条件下获得的钕激光玻璃的质量进行分析，获得了一种高均匀性、低OH根及低铂含量钕激光玻璃的生产方法。通过工艺改进及完善，总结出了一套合理的玻璃熔炼制度。     

Yb3+敏化宽波带掺Er3+氟磷酸盐玻璃的发光性质及Judd-Ofelt理论研究

采用高温熔融法制备了一种新的Er3+/Yb3+共掺氟磷酸盐玻璃,测试和分析了其密度、吸收光谱以及荧光光谱,讨论了Er3+离子和Yb3+离子对光谱性质的影响.根据Judd-Ofelt理论计算了玻璃中Er3+离子的强度参数Ωt(t=2,4,6),分别为Ω2=4.36×10-20cm2,Ω4=1.35×10-20cm2,Ω6=0.79×10-20cm2,以及Er3+离子4I13/2能级荧光寿命τm=8.26ms.主发射峰1.53μm处半高宽(FWHM)为68nm.根据McCumber理论计算了Er3+的受激发射截面σe=8.5×10-21cm2.比较了不同玻璃基质中Er3+离子的光谱特性,结果表明:Er3+/Yb3+双掺氟磷酸盐玻璃在1.53μm附近具有较宽的半高宽和较大的受激发射截面,是一种高增益掺铒光纤放大器的理想介质材料.     

稀土掺杂硼铝硅酸盐玻璃结构的NMR研究

采用魔角核磁共振（MAS NMR）研究了稀土掺杂B2O3-Al2O3-SiO2玻璃的结构及其组成和热处理等因素对玻璃结构的影响。研究发现，在B2O3-Al2O3-SiO2玻璃结构中，硼的配位主要是三角体[BO3]和[BO4]，铝的配位主要是[AlO4]，[AlO5]和少量的[AlO6]。随着B2O3-Al2O3-SiO2玻璃中BaO含量的增加，[BO3]逐渐向[BO4]转变，[AlO5]和[AlO5]也转变为[AlO4]。此外，由于稀土离子比钡离子更高的离子场强，其能够积聚硼氧结构使得其形成了巨大的网络结构。随着稀土掺量的增加，玻璃结构中的硅氧配位逐渐以Q4（3T）为主。热处理对玻璃结构中的硼氧和铝氧配位影响很小。     

锂离子导电硫氧化物玻璃的电子能谱

锂离子导电硫氧化物玻璃的电子能谱高海春，孙长敏，火炎，张瑞峰，李兴林（中国科学院盐湖研究所西宁）（中国科学院长春应用化学研究所长春１３００２２）关键词固体电解质，锂离子导体，硫氧化物玻璃，ＸＰＳ用易极化的硫取代氧，可在Ｌｉ２Ｓ－Ｂ２Ｓ３－ＬｉＩ体系［...     

Tm3+/Yb3+共掺氧氯碲酸盐玻璃上转换发光研究

制备了Tm^3＋/Yb^3＋共掺氧氯碲酸盐玻璃, 研究了玻璃的热稳定性能、 Raman光谱和上转换发光光谱, 分析了上转换发光机制. 结果表明： 通过980 nm的激光二极管激发, 在室温下同时观察到强烈的蓝光（476 nm）和微弱的红光（649 nm）, 分别是Tm^3＋离子的1G4→3H6和1G4→3H4跃迁. 随氯化铅含量增加, 基质玻璃的热稳定性能增强, 基质玻璃的声子能量降低, 上转换蓝光和红光的强度增加. 表明Tm^3＋/Yb^3＋共掺氧氯碲酸盐玻璃是一种上转换蓝光激光器的潜在基质材料.     

钕掺杂磷酸盐微晶玻璃的制备及表征

利用熔融和晶化技术制备掺钕磷酸盐玻璃陶瓷。 采用差热分析、X射线衍射、扫描电子显微镜、紫外 可见 近红外分光光度计及荧光光谱仪对材料进行表征和分析。 结果表明,在490～540 ℃核化1～2 h,在550 ℃晶化1～3 h,可制得主晶相为Al2SiO5的透明玻璃陶瓷。 其透过率可达69%,晶粒平均尺寸为90 nm,并随热处理时间的增加逐渐增大,但透过率降低。 由于Nd3+在热处理后进入到Al2SiO5晶相中,使荧光谱线在1 056 nm处峰值比原始玻璃强度大。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.