Surface Termination on Unstable Methylammonium-based Perovskite Using a Steric Barrier for Improved Perovskite Solar Cells

Compared to widely adopted low-dimensional/three-dimensional (LD/3D) heterostructure, functional organic cation based surface termination on perovskite can not only realize advantage of defect passivation but also prevent potential disadvantage of the heterostructure induced intercalation into 3D perovskite. However, it is still very challenging to controllably construct surface termination on organic–inorganic hybrid perovskite because the functional organic cations’ substitution reaction is easy to form LD/3D heterostructure. Here, we report using a novel benzyltrimethylammonium (BTA) functional cation with rational designed steric hindrance to effectively surface terminate onto methylammonium lead triiodide (MAPbI₃) perovskite, which is composed of the most unstable MA cations. The BTA cation is difficult to form a specific 1.5-dimensional perovskite of BTA₄Pb₃I₁₀ by cation substitution with MA cation, which then provides a wide processing window (around 10 minutes) for surface terminating on MAPbI₃ films. Moreover, the BTAI surface terminated BTAI-MAPbI₃ shows better passivation effect than BTA₄Pb₃I₁₀-MAPbI₃ heterojunction. Finally, BTAI surface terminated solar cell (0.085 cm²) and mini-module (11.52 cm²) obtained the efficiencies of 22.03 % and 18.57 %, which are among the highest efficiencies for MAPbI₃ based ones.     

In CH3NH3PbI3 Perovskite Film,the Surface Termination Layer Dominates the Moisture Degradation Pathway

Theoretical studies have shown that surface terminations, such as MAI or PbI layers, greatly affect the environmental stability of organic–inorganic perovskite. However, until now, there has been little effort to experimentally detect the existence of MAI or PbI terminations on MAPbI₃ grains, let alone disclose their effects on the humidity degradation pathway of perovskite solar cell. Here, we successfully modified and detected the surface terminations of MAI and PbI species on polycrystalline MAPbI₃ films. MAI-terminated perovskite film followed the moisture degradation process from MAPbI₃ to hydrate MAPbI₃⋅H₂O and then into PbI₂, with penetration of water molecules being the main driving force leading to the degradation of MAPbI₃ layer by layer. In contrast, for the PbI-terminated perovskite film in a humid atmosphere, a deprotonation degradation pathway was confirmed, in which the film preferentially degraded directly from MAPbI₃ into PbI₂, here the iodine defects played a key role in promoting the dissociation of water molecules into OH⁻ and further catalyzing the decomposition of perovskite.     

Steric Mixed‐Cation 2D Perovskite as a Methylammonium Locker to Stabilize MAPbI3

The reduced dimension perovskite including 2D perovskites are one of the most promising strategies to stabilize lead halide perovskite. A mixed‐cation 2D perovskite based on a steric phenyltrimethylammonium (PTA) cation is presented. The PTA‐MA mixed‐cation 2D perovskite of PTAMAPbI₄ can be formed on the surface of MAPbI₃ (PTAI‐MAPbI₃) by controllable PTAI intercalation by either spin coating or soaking. The PTAMAPbI₄ capping layer can not only passivate PTAI‐MAPbI₃ perovskite but also act as MA⁺ locker to inhibit MAI extraction and significantly enhance the stability. The highly stable PTAI‐MAPbI₃ based perovskite solar cells exhibit a reproducible photovoltaic performance with a champion PCE of 21.16 %. Such unencapsulated devices retain 93 % of initial efficiency after 500 h continuous illumination. This steric mixed‐cation 2D perovskite as MA⁺ locker to stabilize the MAPbI₃ is a promising strategy to design stable and high‐performance hybrid lead halide perovskites.     

Carrier dynamics in CsPbI3 perovskite microcrystals synthesized in solution phase

Carrier diffusion and recombination kinetics in all-inorganic CsPbI₃ perovskite microcrystals directly synthesized in solution phase are reported.     

Optoelectronic and morphology properties of perovskite/silicon interface layer for tandem solar cell application

Silicon (Si) solar cell has low optical absorption because of the low and indirect bandgap of Si, and the efficiency was trapped at 25% for 15 years. Si solar cell is able to achieve efficiency up to 30% by adding perovskite as multiple bandgap material through tandem formation. In this paper, the Si/perovskite interface layer was characterized to study the compatibility of perovskite on fluorine-doped tin oxide (FTO) glass and p-type Si wafer (p-Si). The single solution deposition step of methyl ammonium lead iodide, CH₃NH₃PbI₃ (MAPbI₃) perovskite film, was spin-coated at different concentration. The physical properties of the MAPbI₃/FTO and MAPbI₃/p-Si were obtained by profilometer, atomic force microscope, X-ray diffraction, and Raman spectroscopy. The optical properties were analyzed by ultraviolet-visible spectroscopy, photoluminescence, and infrared transmission. Then the electrical properties were measured by Hall effect. From the measurement, it is observed that 1.2M concentration of MAPbI₃ thin film has the highest thickness, smoothest film surface, and largest crystallite size compared with 0.8M and 1.0M. It is found that there is an interaction in perovskite/Si interface and caused in a low-wavelength shift, and the increase in concentration of MAPbI₃ helped in intensifying the Raman signal produced. 1.2M MAPbI₃ thin film had the highest enhancement in light trapping property rather than 0.8M and 1.0M. The bulk concentration and conductivity of 1.2M perovskite were higher, but the resistivity was lower than 0.8M MAPbI₃ because of more CH₃NH₃I and PbI₂ concentration within MAPbI₃ perovskite compound.     

Stabilization of Highly Efficient and Stable Phase‐Pure FAPbI3 Perovskite Solar Cells by Molecularly Tailored 2D‐Overlayers

As a result of their attractive optoelectronic properties, metal halide APbI₃ perovskites employing formamidinium (FA⁺) as the A cation are the focus of research. The superior chemical and thermal stability of FA⁺ cations makes α‐FAPbI₃ more suitable for solar‐cell applications than methylammonium lead iodide (MAPbI₃). However, its spontaneous conversion into the yellow non‐perovskite phase (δ‐FAPbI₃) under ambient conditions poses a serious challenge for practical applications. Herein, we report on the stabilization of the desired α‐FAPbI₃ perovskite phase by protecting it with a two‐dimensional (2D) IBA₂FAPb₂I₇ (IBA=iso‐butylammonium overlayer, formed via stepwise annealing. The α‐FAPbI₃/IBA₂FAPb₂I₇ based perovskite solar cell (PSC) reached a high power conversion efficiency (PCE) of close to 23 %. In addition, it showed excellent operational stability, retaining around 85 % of its initial efficiency under severe combined heat and light stress, that is, simultaneous exposure with maximum power tracking to full simulated sunlight at 80 °C over 500 h.     

Steric Mixed-Cation 2D Perovskite as a Methylammonium Locker to Stabilize MAPbI3

The reduced dimension perovskite including 2D perovskites are one of the most promising strategies to stabilize lead halide perovskite. A mixed-cation 2D perovskite based on a steric phenyltrimethylammonium (PTA) cation is presented. The PTA-MA mixed-cation 2D perovskite of PTAMAPbI₄ can be formed on the surface of MAPbI₃ (PTAI-MAPbI₃) by controllable PTAI intercalation by either spin coating or soaking. The PTAMAPbI₄ capping layer can not only passivate PTAI-MAPbI₃ perovskite but also act as MA⁺ locker to inhibit MAI extraction and significantly enhance the stability. The highly stable PTAI-MAPbI₃ based perovskite solar cells exhibit a reproducible photovoltaic performance with a champion PCE of 21.16 %. Such unencapsulated devices retain 93 % of initial efficiency after 500 h continuous illumination. This steric mixed-cation 2D perovskite as MA⁺ locker to stabilize the MAPbI₃ is a promising strategy to design stable and high-performance hybrid lead halide perovskites.     

Stabilization of Highly Efficient and Stable Phase-Pure FAPbI3 Perovskite Solar Cells by Molecularly Tailored 2D-Overlayers

As a result of their attractive optoelectronic properties, metal halide APbI₃ perovskites employing formamidinium (FA⁺) as the A cation are the focus of research. The superior chemical and thermal stability of FA⁺ cations makes α-FAPbI₃ more suitable for solar-cell applications than methylammonium lead iodide (MAPbI₃). However, its spontaneous conversion into the yellow non-perovskite phase (δ-FAPbI₃) under ambient conditions poses a serious challenge for practical applications. Herein, we report on the stabilization of the desired α-FAPbI₃ perovskite phase by protecting it with a two-dimensional (2D) IBA₂FAPb₂I₇ (IBA=iso-butylammonium overlayer, formed via stepwise annealing. The α-FAPbI₃/IBA₂FAPb₂I₇ based perovskite solar cell (PSC) reached a high power conversion efficiency (PCE) of close to 23 %. In addition, it showed excellent operational stability, retaining around 85 % of its initial efficiency under severe combined heat and light stress, that is, simultaneous exposure with maximum power tracking to full simulated sunlight at 80 °C over 500 h.     

Thin films of MAPbI3 and MA0.15FA0.75Cs0.1PbI3 perovskites under femtosecond laser irradiation: nonlinear optical absorption and kinetics of photodegradation

The thin MAPbI₃ and MA_0.15FA_0.75Cs_0.1PbI₃ perovskite films have strong nonlinear absorption with coefficients of 443 ± 20 and 830 ± 50 cm GW^–1, respectively, due to two-photon absorption at 1064 nm. The photochemical degradation of perovskite films was observed upon irradiation with femtosecond pulses at 532 nm, and the depth of photodegradation decreased in perovskite films protected with a PMMA polymer layer.     

Investigation of the Stability of Methylammonium Lead Iodide (MAPbI3) Film Doped with Lead Cesium Triiodide (CsPbI3) Quantum Dots under an Oxygen Plasma Atmosphere

In this study, we describe composited perovskite films based on the doping of lead cesium triiodide (CsPbI₃) quantum dots (QDs) into methylammonium lead iodide (MAPbI₃). CsPbI₃ QDs and MAPbI₃ were prepared by ligand-assisted re-precipitation and solution mixing, respectively. These films were optimized by oxygen plasma treatment, and the effect of powers from 0 to 80 W on the structural properties of the composited perovskite films is discussed. The experimental results showed that the light-harvesting ability of the films was enhanced at 20 W. The formation of the metastable state (lead(II) oxide and lead tetroxide) was demonstrated by peak differentiation-imitating. A low power enhanced the quality of the films due to the removal of organic impurities, whereas a high power caused surface damage in the films owing to the severe degradation of MAPbI₃.     

Encapsulating Perovskite Quantum Dots in Iron‐Based Metal–Organic Frameworks (MOFs) for Efficient Photocatalytic CO2 Reduction

Improving the stability of lead halide perovskite quantum dots (QDs) in a system containing water is the key for their practical application in artificial photosynthesis. Herein, we encapsulate low‐cost CH₃NH₃PbI₃ (MAPbI₃) perovskite QDs in the pores of earth‐abundant Fe‐porphyrin based metal organic framework (MOF) PCN‐221(Fe_x) by a sequential deposition route, to construct a series of composite photocatalysts of MAPbI₃@PCN‐221(Fe_x) (x=0–1). Protected by the MOF the composite photocatalysts exhibit much improved stability in reaction systems containing water. The close contact of QDs to the Fe catalytic site in the MOF, allows the photogenerated electrons in the QDs to transfer rapidly the Fe catalytic sites to enhance the photocatalytic activity for CO₂ reduction. Using water as an electron source, MAPbI₃@PCN‐221(Fe_0.2) exhibits a record‐high total yield of 1559 μmol g^?1 for photocatalytic CO₂ reduction to CO (34 %) and CH₄ (66 %), 38 times higher than that of PCN‐221(Fe_0.2) in the absence of perovskite QDs.     

Highly Efficient,Reproducible, Uniform (CH3NH3)PbI3 Layer by Processing Additive Dripping for Solution‐Processed Planar Heterojunction Perovskite Solar Cells

A processing additive dripping (PAD) approach to forming highly efficient (CH₃NH₃)PbI₃ (MAPbI₃) perovskite layers was investigated. A MAPbI₃(CB/DIO) perovskite film fabricated by this approach, which included briefly dripping chlorobenzene incorporating a small amount of diiodooctane (DIO) during casting of a MAPbI₃ perovskite precursor dissolved in dimethylformamide, exhibited superior smooth, uniform morphologies with high crystallinity and large grains and revealed completely homogeneous surface coverage. The surface coverage and morphology of the substrate significantly affected the photovoltaic performance of planar heterojunction (PHJ) perovskite solar cells (PrSCs), resulting in a power conversion efficiency of 11.45 % with high open‐circuit voltage of 0.91 V and the highest fill factor of 80.87 %. Moreover, the PAD approach could effectively provide efficient MAPbI₃(CB/DIO) perovskite layers for highly efficient, reproducible, uniform PHJ PrSC devices without performance loss or variation even over larger active areas.     

Low‐Energy Electron‐Induced Transformations in Organolead Halide Perovskite

Methylammonium lead iodide perovskite (MAPbI₃), a prototype material for potentially high‐efficient and low‐cost organic–inorganic hybrid perovskite solar cells, has been investigated intensively in recent years. A study of low‐energy electron‐induced transformations in MAPbI₃ is presented, performed by combining controlled electron‐impact irradiation with X‐ray photoelectron spectroscopy and scanning electron microscopy. Changes were observed in both the elemental composition and the morphology of irradiated MAPbI₃ thin films as a function of the electron fluence for incident energies from 4.5 to 60 eV. The results show that low‐energy electrons can affect structural and chemical properties of MAPbI₃. It is proposed that the transformations are triggered by the interactions with the organic part of the material (methylammonium), resulting in the MAPbI₃ decomposition and aggregation of the hydrocarbon layer.     

(W6I8)Cl4 – A Basic Model Compound for Photophysically Active [(W6I8)L6]2– Clusters?

The heteroleptic cluster compound (W₆I₈)Cl₄ was prepared by thermal conversion of the homoleptic clusters W₆I₁₂ and W₆Cl₁₂ at 700 °C to yield a bright yellow powder. The presence of the smaller chlorido ligands in apical positions of [(W₆I₈)Cl₆]^2– creates nearly spherically clusters showing thermal and chemical inertness. Photoluminescence studies revealed a strong red phosphorescence from excited spin‐triplet states.     

The Role of Surface Termination in Halide Perovskites for Efficient Photocatalytic Synthesis

Halide perovskites have received attention in the field of photocatalysis owing to their excellent optoelectronic properties. However, the semiconductor properties of halide perovskite surfaces and the influence on photocatalytic performance have not been systematically clarified. Now, the conversion of triose (such as 1,3‐dihydroxyacetone (DHA)) is employed as a model reaction to explore the surface termination of MAPbI₃. By rational design of the surface termination for MAPbI₃, the production rate of butyl lactate is substantially improved to 7719 μg g^?1 cat. h^?1 under visible‐light illumination. The MAI‐terminated MAPbI₃ surface governs the photocatalytic performance. Specially, MAI‐terminated surface is susceptible to iodide oxidation, which thus promotes the exposure of Pb^II as active sites for this photocatalysis process. Moreover, MAI‐termination induces a p‐doping effect near the surface for MAPbI₃, which facilitates carrier transport and thus photosynthesis.     

Preparation and Characterization of Thin-Film Solar Cells with Ag/C60/MAPbI3/CZTSe/Mo/FTO Multilayered Structures

New solar cells with Ag/C₆₀/MAPbI₃/Cu₂ZnSnSe₄ (CZTSe)/Mo/FTO multilayered structures on glass substrates have been prepared and investigated in this study. The electron-transport layer, active photovoltaic layer, and hole-transport layer were made of C₆₀, CH₃NH₃PbI₃ (MAPbI₃) perovskite, and CZTSe, respectively. The CZTSe hole-transport layers were deposited by magnetic sputtering, with the various thermal annealing temperatures at 300 °C, 400 °C, and 500 °C, and the film thickness was also varied at 50~300 nm The active photovoltaic MAPbI₃ films were prepared using a two-step spin-coating method on the CZTSe hole-transport layers. It has been revealed that the crystalline structure and domain size of the MAPbI₃ perovskite films could be substantially improved. Finally, n-type C₆₀ was vacuum-evaporated to be the electronic transport layer. The 50 nm C₆₀ thin film, in conjunction with 100 nm Ag electrode layer, provided adequate electron current transport in the multilayered structures. The solar cell current density–voltage characteristics were evaluated and compared with the thin-film microstructures. The photo-electronic power-conversion efficiency could be improved to 14.2% when the annealing temperature was 500 °C and the film thickness was 200 nm. The thin-film solar cell characteristics of open-circuit voltage, short-circuit current density, fill factor, series-resistance, and Pmax were found to be 1.07 V, 19.69 mA/cm², 67.39%, 18.5 Ω and 1.42 mW, respectively.     

Post‐Treatment of CH3NH3PbI3/PbI2 Composite Films with Methylamine to Realize High‐Performance Photoconductor Devices

Organometallic halide perovskites have attracted great research interest as light‐active materials for use in optoelectronics. Here, we report a high‐performance photoconductor based on a methylammonium lead iodide (MAPbI₃) film that was prepared from a methylamine‐treated MAPbI₃/PbI₂ perovskite film. An ultrahigh responsivity of 3.6 A W^?1 and detectivity of 5.4×10¹² Jones were obtained for the film under 0.5 mW cm^?2 white‐light illumination. In addition, under 420 nm light irradiation, the film exhibited its highest responsivity and detectivity of 30 A W^?1 and 2.4×10¹⁴ Jones, respectively. The excellent photo‐response performance results from the improved electronic quality and suppressed nonradiative recombination channels of the treated perovskite thin film.     

Targeted Management of Perovskite Film by Co(II) Sulfophenyl Porphyrin for Efficient and Stable Solar Cells†

In the lead halide perovskite solar cells (PSCs), the redox reaction of I^– and Pb²⁺ ions in perovskite materials under the fabrication and operation processes causes the formation of defects to destroy the cell efficiency and long-term stability. Herein, we have employed a Co(II) sulfophenyl porphyrin (CoTPPS) to modify the perovskite film. The sulfonic group could coordinate with Pb²⁺ to efficiently passivate the uncoordinated Pb²⁺. Additionally, Co²⁺ ions in CoTPPS could react with I₂ generated under the thermal and light stress to yield the Co³⁺ and I^–, thus achieving the regeneration of I^– in perovskite film. Therefore, the CoTPPS could realize the targeted management of the imperfections in perovskite film. As a result, the modified PSCs reveal the remarkably enhanced cell performance. More importantly, the CoTPPS modified device retains 75% of its initial efficiency value storing at 85°C for 2000 h and about 70% of its efficiency when being continuously illuminated at a simulated sunlight for 1200 h. This strategy tackles the chemical reaction and inhibits the defect generation, thus improving the operational stability and efficiency of PSCs.      

Promoting Photocatalytic H2 Evolution through Retarded Charge Trapping and Recombination by Continuously Distributed Defects in Methylammonium Lead Iodide Perovskite

Inspired by its great success in the photovoltaic field, methylammonium lead iodide perovskite (MAPbI₃) has recently been actively explored as photocatalysts in H₂ evolution reactions. However, the practical application of MAPbI₃ photocatalysts remains hampered by the intrinsically fast trapping and recombination of photogenerated charges. Herein, we propose a novel strategy of regulating the distribution of defective areas to promote charge-transfer dynamics of MAPbI₃ photocatalysts. By deliberately designing and synthesizing the MAPbI₃ photocatalysts featuring a unique continuation of defective areas, we demonstrate that such a feature enables retardation of charge trapping and recombination via lengthening the charge-transfer distance. As an outcome, such MAPbI₃ photocatalysts turn out to achieve an impressive photocatalytic H₂ evolution rate as high as 0.64 mmol ⋅ g⁻¹ ⋅ h⁻¹, one order of magnitude higher than that of the conventional MAPbI₃ photocatalysts. This work establishes a new paradigm for controlling charge-transfer dynamics in photocatalysis.     

Tetra‐ammonium Zinc Phthalocyanine to Construct a Graded 2D–3D Perovskite Interface for Efficient and Stable Solar Cells

The crystallographic defects inevitably incur during the solution processed organic‐inorganic hybrid perovskite film, especially at surface and the grain boundaries (GBs) of perovskite film, which can further result in the reduced cell performance and stability of perovskite solar cells (PSCs). Here, a simple defect passivation method was employed by treating perovskite precursor film with a hydrophobic tetra‐ammonium zinc phthalocyanine (ZnPc). The results demonstrated that a 2D‐3D graded perovskite interface with a capping layer of 2D (ZnPc)_0.5MA_n ? 1Pb_nI_3n + 1 perovskite together with 3D MAPbI₃ perovskite was successfully constructed on the top of 3D perovskite layer. This situation realized the efficient GBs passivation, thus reducing the defects in GBs. As expected, the corresponding PSCs with modified perovskite revealed an improved cell performance. The best efficiency reached 19.6%. Especially, the significantly enhanced long‐term stability of the responding PSCs against humidity and heating was remarkably achieved. Such a strategy in this work affords an efficient method to improve the stability of PSCs and thus probably brings the PSCs closer to practical commercialization.