Nanostructured NiMoO4 as active electrocatalyst for oxygen evolution

Hydrothermally synthesized NiMoO₄ nanorods exhibit considerable electrocatalytic properties for the oxygen evolution in alkaline condition. The performance enhancement of ternary NiMoO₄ over binary oxide NiO and MoO₃ is attributed to the inclusion of Mo that promotes the pre-redox reaction of Ni to form active Ni species.     

Electrochemical performances of LaBaCuFeO5+x and LaBaCuCoO5+x as potential cathode materials for intermediate-temperature solid oxide fuel cells

Layered perovskite-structure oxides LaBaCuFeO_5+x (LBCFO) and LaBaCuCoO_5+x (LBCCO) were prepared and the electrical conductivity and electrochemical performance were investigated as potential cathode materials for intermediate-temperature solid oxide fuel cells (IT-SOFCs). The electrical conductivity of LBCCO is much higher than that of LBCFO. Area specific resistances of LBCFO and LBCCO cathode materials on Ce_0.8Sm_0.2O_1.9 (SDC) electrolyte are as low as 0.21 Ω cm² and 0.11 Ω cm² at 700 °C, respectively. The maximum power density of the LBCFO/SDC/Ni-SDC and LBCCO/SDC/Ni-SDC cells with 300 μm thick electrolytes attains 557 mW cm^?2 and 603 mW cm^?2 at 800 ^oC, respectively. Preliminary results demonstrated that the layered perovskite-structure oxides LBCFO and LBCCO are very promising cathode materials for application in IT-SOFCs.     

Assembly of NaTaO3 porous microspheres via imperfect oriented attachment mechanism

Spongy-like NaTaO₃ mesoporous microspheres are assembled from nanoparticles via imperfect oriented attachment. Study shows that the NaTaO₃ spongy microspheres with the diameters of ～1 μm are composed of the fundamental building blocks of ～50 nm NaTaO₃ nanospheres. The high-resolution transmission electron microscopy further reveals that these fundamental building blocks are assembled from primary building blocks of ～10 nm NaTaO₃ nanocrystals. The pore diameters of these spongy microspheres are ca. 30 nm and the Brunauer–Emmett–Teller (BET) surface area is calculated to be 57.8 m² g^?1. This interesting ternary alkali metal composite oxide of NaTaO₃ spongy microspheres with high specific surface area and strong stability will be favorable for their practical application in photocatalysis. This synthesis route may throw light on the fabrication of the binary or ternary porous metal oxides by geometrical stacking of the nanobuilding blocks via imperfect oriented attachment.     

Designing high-capacity cathode materials for sodium-ion batteries

Na-rich layered oxides as cathode materials for sodium-ion batteries were designed using an electrochemical method based on Li-rich layered oxides. The materials show high specific capacity that can reach 234 mAh/g at a current of 5 mA/g. The energy density of this material (644 Wh/kg) is even higher than those of commercial cathodes for lithium-ion batteries, such as LiFePO₄ and LiMn₂O₄. Kinetic analysis of Na⁺ insertion/extraction into/from the Na-rich layered oxide reveals that the Na⁺ diffusion coefficient is about 10^− 14 cm²/s.     

An understanding of anomalous capacity of nano-sized CoO anode materials for advanced Li-ion battery

Nanostructured transition metal oxides are of great interest as a new generation of anode materials for high energy density lithium-ion batteries. In this work, research has been focused on the nano-sized (grain size ～7 nm) CoO anode material and this material delivers charge capacity of 900 mAh g^?1 that exceeds the theoretical value of 715 mAh g^?1. Possible reason for this unaccounted and unexplained anomalous capacity of the nano-sized CoO material has been suggested by thermogravimetric analysis. A mechanism for this interesting behavior has been systematically evaluated by using X-ray absorption spectroscopy. The anomalous capacity is proposed to be associated with the formation of oxygen-rich CoO material. The results obtained from the nano-sized CoO material have been compared with relatively larger-sized material (grain size ～32 nm).     

A voltammetric study of the binding of copper(II) to peptide fragments of prion

Binding of copper to three peptide fragments of prion (Cu²⁺ binding sites: 60–91, 92–96 and 180–193 amino acid residues) was investigated by anodic stripping voltammetry to determine the stoichiometries of Cu²⁺-prion peptide interactions. The method relies on the synthesis of N-terminally acetylated/C-terminally amidated peptide fragments of prion by solid-phase synthesis and direct monitoring of the oxidation current of copper in the absence and presence of each prion fragment. Titration curves of Cu²⁺ with Ac-PHGGGWGQ-NH₂, Ac-GGGTH-NH₂ and Ac-VNITKQHTVTTTT-NH₂ were obtained in concentrations ranging from 8.52 × 10^?7 to 5.08 × 10^?6, 3.95 × 10^?7 to 1.94 × 10^?6 and 7.82 × 10^?8 to 4.51 × 10^?7 M, respectively. The acquired data were used to calculate the stoichiometries (one peptide per Cu²⁺ ion for all the three studied systems) and apparent dissociation constants (K_d = 4.37 × 10^?8–3.50 × 10^?10 M) for the three complexes.     

Nanocrystalline MnO thin film anode for lithium ion batteries with low overpotential

Nanocrystalline MnO thin film has been prepared by a pulsed laser deposition (PLD) method. The reversible lithium storage capacity of the MnO thin film electrodes at 0.125C is over 472 mAh g^?1 (3484 mAh cm^?3) and can be retained more than 90% after 25 cycles. At a rate of 6C, 55% value of the capacity at 0.125C rate can be obtained for both charge and discharge. As-prepared MnO thin film electrodes show the lowest values of overpotential for both charge and discharge among transition metal oxides. All these performances make MnO a promising high capacity anode material for Li-ion batteries.     

Pseudocapacitive effect and Li+ diffusion coefficient in three-dimensionally ordered macroporous vanadium oxide for energy storage

In order to act as extrinsic pseudocapacitor materials, nanoscale vanadium oxides are required to simultaneously exhibit a capacitance-based high power density and an intercalation-based high energy density. We have fabricated a three-dimensionally ordered macroporous (3DOM) structure with a wall thickness of 14 nm that fulfills the above requirements. The 3DOM vanadium oxide film exhibits high rate performance with 355 F g^− 1 at 0.5 A g^− 1 and 125 F g^− 1 at 15 A g^− 1. The enhanced pesudocapacitive effect and Li-ion diffusion coefficient based on the 3DOM nanostructure, also contributes to the high rate capability of vanadia, which can be confirmed by cyclic voltammetry and chronoamperometry.     

Electrical conductivity and Hf4+ ion substitution range in NaSICON system

In this paper, we present the synthesis and characterizations of NaSICON-type ionic conducting ceramics of the general formula Na_1+xM_1.775Si_x−0.9P_3.9−xO₁₂ with 1.8 ≤ x ≤ 2.2 and M = Zr or Hf. The effect of the total substitution of zirconium by hafnium on electric properties has been studied. The various compositions were prepared by using the sol–gel method and the synthesized precursors were characterized by coupled DTA–TG. The oxides obtained after pyrolysis of the precursors were identified by X-ray diffraction. A sintering study by thermodilatometry permits to select the best thermal cycle adapted to our ceramics. Furthermore, the electric conductivity of the sintered ceramic samples was characterized by complex impedance spectroscopy. These results show that ceramics containing Zr synthesized by soft method, present a higher total conductivity than those obtained in literature (to be around 10⁻⁴ S cm⁻¹). The total substitution of Zr by Hf still improves this conductivity for some compositions.     

Enhancement of electrochemical performance and thermal compatibility of GdBaCo2/3Fe2/3Cu2/3O5+δ cathode on Ce1.9Gd0.1O1.95 electrolyte for IT-SOFCs

Transition-metal doped double-perovskite structure oxides GdBaCo_2/3Fe_2/3Ni_2/3O_5+δ (FN-GBCO), GdBaCo_2/3Fe_2/3Cu_2/3O_5+δ (FC-GBCO), GdBaCoCuO_5+δ (C-GBCO) and pristine GdBaCo₂O_5+δ (GBCO) were synthesized via a citrate combustion method. The thermal-expansion coefficient (TEC) and electrochemical performance of the oxides were investigated as potential cathodes for intermediate-temperature solid oxide fuel cells (IT-SOFCs). The TEC exhibited by the FC-GBCO cathode up to 900 °C is 14.6 × 10^?6 °C^?1, which is lower than the value of GBCO (19.9 × 10^?6 °C^?1). Area specific resistances (ASR) of 0.165 Ω cm² at 700 °C and 0.048 Ω cm² at 750 °C were achieved for the FC-GBCO cathode on a Ce_0.9Gd_0.1O_1.95 (CGO) electrolyte. An electrolyte supported (300 μm thick) single-cell configuration of FC-GBCO/CGO/Ni-CGO attained a maximum power density of 435 mW cm^?2 at 700 °C. The unique composition of GBCO co-doped with Fe and Cu ions in the Co sites exhibited reduced TEC and enhancement of electrochemical performance and good chemical compatibility with CGO, and this composition is proving to be a potential cathode for IT-SOFCs.     

Heat capacities,third-law entropies and thermodynamic functions of the negative thermal expansion material Zn2GeO4 from T=(0 to 400) K

The molar heat capacity of Zn₂GeO₄, a material which exhibits negative thermal expansion below ambient temperatures, has been measured in the temperature range 0.5⩽(T/K)⩽400. At T=298.15 K, the standard molar heat capacity is (131.86 ± 0.26) J · K⁻¹ · mol⁻¹. Thermodynamic functions have been generated from smoothed fits of the experimental results. The standard molar entropy at T=298.15 K is (145.12 ± 0.29) J · K⁻¹ · mol⁻¹. The existence of low-energy modes is supported by the excess heat capacity in Zn₂GeO₄ compared to the sums of the constituent binary oxides.     

Synthesis of Photoluminophors Using a Continuous Solid-phase Technology

Solid phase method of strontium aluminate synthesis (SrAl₂O₄) is based on calcination of the mixture of strontium carbonate (SrCO₃), aluminum oxide (Al₂O₃), oxides of REM (europium, dysprosium) and a mineralizer - borate glass (H₃BO₃) at a temperature of 1200-1400 °C within 4-6 hours. We have proposed a technique of thermal shock – rapid heating and rapid cooling of the sample by means of which the duration of synthesis is reduced to 30 minutes.     

Temporal evolution study of the plasma induced by CO2 pulsed laser on targets of titanium oxides

This paper reports studies on time-resolved laser induced breakdown spectroscopy (LIBS) of plasmas induced by IR nanosecond laser pulses on the titanium oxides TiO and TiO₂ (anatase). LIBS excitation was performed using a CO₂ laser. The laser-induced plasma was found strongly ionized yielding Ti⁺, O⁺, Ti^2 +, O^2 +, Ti^3 +, and Ti^4 + species and rich in neutral titanium and oxygen atoms. The temporal behavior of specific emission lines of Ti, Ti⁺, Ti^2 + and Ti^3 + was characterized. The results show a faster decay of Ti^3 + and Ti^2 + ionic species than that of Ti⁺ and neutral Ti atoms. Spectroscopic diagnostics were used to determine the time-resolved electron density and excitation temperatures. Laser irradiation of TiO₂-anatase induces on the surface sample the polymorphic transformation to TiO₂-rutile. The dependence on fluence and number of irradiation pulses of this transformation was studied by micro-Raman spectroscopy.     

Structure and oxygen storage capacity of Pr/Nd doped CeO2–ZrO2 mixed oxides

Binary Ce–Zr (CZ), trinary Ce–Zr–Pr (CZP), Ce–Zr–Nd (CZN) mixed oxides were prepared by coprecipitation. The structural and textural properties were characterized by the X-ray diffraction (XRD) analysis, Brunauer–Emmett–Teller (BET) method, Raman and X-ray absorption near-edge spectra (XANES) techniques, while the oxygen storage capacity (OSC) was evaluated under both dynamic and static conditions at 500 °C. The doping of Pr or Nd cations causes the lattice deformation of the tetragonal Zr-rich mixed oxides to form a pseudocubic structure and prevents the phase demixing after calcination in flowing steam/air at 1050 °C for 5 h. After the hydrothermal ageing treatment, the doped samples show higher BET surface areas and better oxygen mobility. Pr exists mainly in the form of trivalent cations in the aged CZP and functions primarily as the doping element with large ionic radius instead of redox couple Pr³⁺/Pr⁴⁺, which may introduce more Ce³⁺ species and hereby more lattice defects. Among the aged samples, CZP shows the best oxygen storage capacity and the fastest oxygen release rate.     

Stannous-acetylacetonate： A new catalyst for poly（trimethylene terephthalate） synthesis

Stannous-acetylacetonate was prepared efficiently and characterized by 1H NMR and FT-IR. Its catalytic activity for poly(trimethylene terephthalate) (PTT) synthesis was investigated. By this catalyst, the degree of esterification of pure terephthalic acid was up to 91.7% after reaction at 260°C for 2 h, while the intrinsic viscosity and content of ter- minal carboxyl groups of the corresponding PTT polymerized at 260°C, 60 Pa for 2 h was 0.8816 dL/g and 17 mol/t, respectively. Stannous-acetylacetonate was more active and promising than tetrabutyl titanate and stannous octoate for PTT synthesis.     

The Characteristics of Green Calcium Oxide Derived from Aquatic Materials

Thermogravimetric Analysis of three aquatic materials, i.e. cuttlebone, mussel shell and oyster shell, and other physicochemical characteristics were investigated. The highest decomposition rates of aquatic materials under two surrounding gases, i.e. oxygen and nitrogen, exhibited no significant difference for cuttlebone (3.6×10^-5-4.8×10^-5 mg s^-1 mg_initial^-1 at heating rate 5 °C/min and 11.8 ×10^-5 -12.5×10^-5 mg s^-1 mg_initial^-1 at heating rate 15 °C/min) and mussel shell (3.4×10^-5- 5.2×10^-5 mg s^-1 mg_initial^-1 at heating rate 5 °C/min and 11.9×10^-5 – 12.4×10^-5 mg s^-1 mg_initial^-1 at heating rate 15 °C/min), while oyster shell provided the higher decomposition rate under nitrogen surrounding gas (7.6×10^-4 mg s^-1 mg_initial^-1 at heat rate 5 °C/min and 21.53×10^-4 mg s^-1 mg_initial^-1 at heating rate 15 °C/min). This is probably because of the difference in their starting crystalline structures, i.e. aragonite (cuttlebone and mussel shell) and calcite (oyster shell). The cubic calcium oxides were prepared by calcination of three aquatic materials under oxygen and nitrogen surrounding gases at 5 °C/min ramping to 850 °C for 2 hours. All resulting calcium oxides obtained from oxygen atmosphere provided only cubic crystalline phases and the adsorption-desorption isotherms (IUPAC Type III), whereas the calcinations under nitrogen surrounding gas gave a presence of calcium hydroxide crystalline or hydroxyl- contaminate existing with cubic calcium oxide that influences on the strength and the number of carbon dioxide adsorption sites. The specific surface area of all resulting calcium oxides ranged from 0.1 – 1.5 m²/g and the average pore diameter was found in the range of 40-60 nm. The the number of basic sites belonging to CaO derived from Oyster shell or Cuttlebone were improved while firing under oxygen atmosphere. The suitable firing condition is at the low heating rate to develop porous materials.     

Preparation of novel magnetic hollow mesoporous silica microspheres and their efficient adsorption

Ordered mesoporous aluminas with high surface areas (up to 783 m²/g), large pore volumes (up to 0.82 cm³/g) and the presence of complementary micropores (up to 0.17 cm³/g) are synthesized with Pluronic® F127 or P123 triblock copolymers in a one-pot synthesis of metal alkoxide, template and cosolvent molecules such as 1,3,5-trimethylbenzene or 1,3,5-triisopropylbenzene in an acidic ethanol solution at 15 °C. Materials are characterized by nitrogen adsorption analysis, small-angle X-ray diffraction and transmission electron microscopy.     

Optimization and modeling of synthesis parameters of neodymium(III) bromide by dry method using full factorial design analysis

The synthesis of neodymium(III) bromide (NdBr₃) by sintering brominating of neodymium oxide (Nd₂O₃) with ammonium bromide (NH₄Br) was investigated. The influence of various synthesis parameters (temperature, contact time and stoichiometry) on the reaction yield was studied and optimized. The main interaction effects of the synthesis parameters on the reaction yield were also determined by a full 2³ factorial designs with six replicates at the center point.This study showed that the optimum conditions for the synthesis of NdBr₃ are following: contact time t = 60 min, stoichiometry in moles Nd₂O₃:NH₄Br = 1:24 and temperature T = 400 °C. The reaction yield for these parameters was equal to 97.80%. The first order model was obtained to predict the reaction yield as a function of these three parameters. It was shown that all parameters have a significant positive influence on reaction yield. In addition it was pointed out also that the interaction effects between them are significant.     

Low temperature synthesis of ferromagnetic (LaK)MnO3 from KCl,KBr and KI fluxes

Potassium doped lanthanum manganites have been synthesized from KCl, KBr and KI fluxes at 900, 850 and 750 °C respectively. While all the flux-grown oxides are ferromagnetic metals (T_c=290–330 K), the oxides grown from KCl and KBr fluxes crystallize in the rhombohedral structure and that synthesized from KI flux adopts the cubic structure. The enhancement in T_c correlates with the increasing tendency of the flux to get oxidized and decreasing melting points of the flux. Nearly stoichiometric (LaK)MnO₃ with 33 % of Mn⁴⁺ concentration could be prepared at temperature as low as 750 °C. Composition of all the phases have been obtained from the chemical analysis of the elements present.     

Process Improvement of Biogas Production from Anaerobic Co-digestion of Cow Dung and Corn Husk

A study of organic loading rate (OLR) and effect of NaOH concentration on the pretreatment stage of corn husk (CH) was conducted by Face-Centered Central Composite Design (CCF) to improve the biogas production. Three levels of OLR at 25.0 g VS · L⁻¹ · d⁻¹ (OLR₂₅), 35.0 g VS · L⁻¹ · d⁻¹ (OLR₃₅), and 45.0 g VS · L⁻¹ · d⁻¹ (OLR₄₅) were performed with NaOH pretreatment concentration of CH at 25.0% (N₂₅), 35.0% (N₃₅), and 45.0% (N₄₅) (w/w). The optimum production of biogas at 67.6 mL · min⁻¹ with methane concentration of 63.4% has been obtained at the application of OLR at 43.6 g VS · L⁻¹ · d⁻¹ and NaOH concentration at 33% (w/w).