CO2 laser cutting of slate

Slate is a natural stone which has the characteristic that shows a well-developed defoliation plane, allowing to easily split it in plates parallel to that plane which are particularly used as tiles for roof building. At present, the manufacturing of slate is mostly manual, being noisy, powdery and unsafe for the worker. Thus, there is a need to introduce new processing methods in order to improve both the working conditions and the quality of the products made of slate.Following the previous work focused on the drilling and cutting of slate tiles using a Nd : YAG laser, we present in this paper the results of the work carried out to explore the possibilities to cut slate plates by using a CO₂ laser. A 1.5 kW CO₂ laser was used to perform different experiments in which, the influence of some processing parameters (average power, assist gas pressure) on the geometry and quality of the cut was studied. The results obtained show that the CO₂ laser is a feasible tool for a successful cutting of slate.     

Mathematical modeling of hybrid CO2 laser

A Teller–Landau six-temperature model describing the dynamic emission of single-mode TEA CO₂ laser has been adapted. This model has been also used to describe the mechanism of obtaining relatively high-power output pulses from hybrid TE-TEA or CW-TEA CO₂ laser consisting of high- and low-pressure sections. The suggested mathematical model allows to investigate the mechanism which limits the TEA oscillation to single longitudinal mode (SLM) due to the narrow gain bandwidth of low-pressure section, and also to study the effect of the laser input parameters on the smooth output laser pulse parameters. In addition, numerical solutions of non-linear rate equation system of the suggested model are quantitatively discussed. The solutions describe the radiation field intensity, the population inversion, and the energy transfer processes. The calculated values of maximum peak power, total energy in pulse, pulse width, etc. are in a very good agreement with the observed experimental values.     

Optically pumped submillimeter laser lines from CD2Cl2 using a large tunability CW CO2 laser

Twenty-five new laser lines have been obtained in the wavelength region from 155 to 830 μm by optically pumping the CD₂Cl₂ (deuterated dichloromethane) molecule with a CW CO₂ laser having a tunability range of 300 MHz. The wavelength, polarization relative to that of CO₂ pumping radiation, and offset relative to the CO₂ center frequency were determined for all of the new lines and some other already known laser emissions. For all of them we give also the relative intensity and the optimum pressure of operation. Permanent address: Depto de Física e Química da FEIS — UNESP 15.378-000 Ilha Solteira-SP, Brazil     

激光钝化对熔石英修复后损伤性能影响的实验研究

采用10.6 μupm 的 CO₂激光, 对单次激光脉冲辐照修复熔石英存在的烧蚀采用大光斑钝化去除. 经过辐照修复的区域置于前表面测试初始损伤阈值, 结果表明调制造成的损伤得到了一定程度的抑制; 辐照区域置于后表面修复后 熔石英的初始损伤阈值超过了基底的初始损伤阈值. 实验观察到了应力分布外扩, 同时明显减弱. 对损伤增长的测试说明, 经过激光熔融辐照后的损伤点, 当应力释放以后, 损伤扩展初期表现出指数增长趋势, 后期随着辐照次数的增加, 损伤增长不再明显, 并且趋于恒定值.     

Optimization of three gas compositions in a CO2 laser

Three pressures of gases (CO₂, N₂ and He) added into CO₂ laser tube are optimized for obtaining maximal laser output power by applying a genetic algorithm and solving the CO₂ laser kinetics equations. After the optimization, the laser power is increased by 96% as compared with a non-optimal case.     

激光钝化对熔石英修复后损伤性能影响的实验研究

采用10.6 μupm 的 CO₂激光, 对单次激光脉冲辐照修复熔石英存在的烧蚀采用大光斑钝化去除. 经过辐照修复的区域置于前表面测试初始损伤阈值, 结果表明调制造成的损伤得到了一定程度的抑制; 辐照区域置于后表面修复后 熔石英的初始损伤阈值超过了基底的初始损伤阈值. 实验观察到了应力分布外扩, 同时明显减弱. 对损伤增长的测试说明, 经过激光熔融辐照后的损伤点, 当应力释放以后, 损伤扩展初期表现出指数增长趋势, 后期随着辐照次数的增加, 损伤增长不再明显, 并且趋于恒定值.     

AC-chopper application for CW CO2 laser

A microprocessor-based algorithm was developed to control the power supply to a CO₂ laser using an AC-chopper method. This system was connected directly to a CO₂ laser tube without the need for a dc-dc converter or the storage capacitance of a multilevel circuit. The typical CO₂ laser power supply system had a full-bridge series resonant inverter or voltage multiplier. AC-to-AC converter schemes using zero voltage switching (ZVS) can be used efficiently and economically for low and medium power applications.This paper reports the performance characteristics of a symmetrical AC-chopper technology that can maintain the quality of the ac output of a CO₂ laser tube, regardless of the amount of switching loss. The laser was operated to an output power, maximum system efficiency total gas mixture of 37.2 W, 92%, and CO₂:N₂:He=1:9:15, respectively. The laser system, AC-chopper power supply and its operation were examined.     

High-power multibeam CO2 laser for industrial applications

Multibeam CO₂ lasers consist of a large number of closely packed parallel glass discharge tubes, all sharing a common plane parallel resonator. This paper describes construction and operation of a CW multibeam CO₂ laser consisting 20 discharge tubes and cooled length of 1500 mm, delivering 1 kW power. A high-frequency pulser is used for producing preionization in all discharge sections for initiating the main DC discharge simultaneously in all discharge tubes. Plane parallel resonator consists of a plane ZnSe mirror of 90 mm diameter having 60% reflectivity and a gold-coated copper mirror of same diameter. This laser operates in waveguide regime and laser power is not critically sensitive to mirror misalignment.     

CO2 laser assisted removal of UO2 and ThO2 particulates from metal surface

Pulsed laser assisted removal of uranium dioxide and thorium dioxide particulates from stainless steel surface have been studied using a TEA CO₂ laser. Decontamination efficiency is measured as a function of laser fluence and number of pulses. Threshold fluence for the removal of UO₂ particulates has been found to be lower than that required for the removal ThO₂ particulates. Usage of a ZnSe substrate, that is transparent to the laser wavelength used here, enabled us to decouple the cleaning effect arising out of absorption in the particulates from that in the substrate and has contributed towards understanding the mechanism responsible for cleaning. The experimental observations are also corroborated by simple theoretical calculations.     

Intracavity absorption of CO2 laser radiation by chlorofluorocarbon (CFC) gases

Intracavity absorption method was applied to determine the absorption coefficients of trichlorofluorocarbon CCl₃F (CFC-11), dichlorodifluorocarbon CF₂Cl₂ (CFC-12) and chlorodifluorocarbon CHClF₂ (CFC-22) vs. the pressure in the cell inside the cavity of a tunable CO₂ laser at different spectral lines on branches 9R and 10P.The laser output power was measured vs. the gas pressure at different spectral lines on branches 9R, 9P, 10R and 10P of CO₂ molecule transitions. A strong absorption was observed for lines of 9R and 10P branches, whereas a weak absorption was noticed for lines of 9P and 10R branches.The calculation of absorption coefficients was restricted for 9R and 10P due to the oscillating variation of the output power of CO₂ laser vs. the CFC pressure, which was occurred for the lines of 9P and 10R.On the basis of absorption coefficients, the absorption cross-sections for CFC-12 were calculated and compared with the absorption cross-sections found from the previous experiment (where the cell was located outside the cavity), NIST and HITRAN databases, respectively.The obtained data could be useful for CFC gases detection as pollutants in the atmosphere.     

Phase-locking of a multi-channel radial array CO2 laser

A theoretical analysis of phase-locking in a multi-channel radial array CO₂ laser is presented. The concepts are based on the theories of injection phase-locking and matrix optics. The mutual optical coupling occurring within the central region is demonstrated by theoretical deduction. Interrelated graphs of the coupling coefficient and the distance between the coupling position and the cavity mirror are calculated by numerical simulation. The results of the analysis are in accord with experimental results.     

Third-harmonic and fourth-harmonic generations of CO2 laser radiation in a GaSe crystal

Tunable third-harmonic and fourth-harmonic generations of pulsed CO2 laser radiation in a GaSe crystal were demonstrated. The optical properties of GaSe and phase-matching conditions in harmonic generations were investigated. The output peak powers for 3.2 μm and 2.4 μm were measured to be 1500 W and 320 W, with corresponding conversion efficiency from 9.6 μm of 0.1% and 0.02%, respectively.     

Influences of CO2 laser annealing on mechanical and laser-induced damage properties of ZrO2 thin films

Zirconium dioxide (ZrO₂) thin films were deposited on BK7 glass substrates by the electron beam evaporation method. A continuous wave CO₂ laser was used to anneal the ZrO₂ thin films to investigate whether beneficial changes could be produced. After annealing at different laser scanning speeds by CO₂ laser, weak absorption of the coatings was measured by the surface thermal lensing (STL) technique, and then laser-induced damage threshold (LIDT) was also determined. It was found that the weak absorption decreased first, while the laser scanning speed is below some value, then increased. The LIDT of the ZrO₂ coatings decreased greatly when the laser scanning speeds were below some value. A Nomarski microscope was employed to map the damage morphology, and it was found that the damage behavior was defect-initiated both for annealed and as-deposited samples. The influences of post-deposition CO₂ laser annealing on the structural and mechanical properties of the films have also been investigated by X-ray diffraction and ZYGO interferometer. It was found that the microstructure of the ZrO₂ films did not change. The residual stress in ZrO₂ films showed a tendency from tensile to compressive after CO₂ laser annealing, and the variation quantity of the residual stress increased with decreasing laser scanning speed. The residual stress may be mitigated to some extent at proper treatment parameters.     

Gain and saturation intensity parameters in a transverse-flow CO2 laser

Details of an experimental investigation of the output characteristics of the 1.2 kW cw transverse-flow, electrically excited CO₂ laser are presented. They were used for estimation of the saturation intensity and the laser cavity loss values, as they follow from the Rigrod-type model of laser operation. The saturation intensity parameter was calculated from measurements of the output power and small signal gain performed with the same experimental conditions. Measurements of the small signal gain were conducted at different points along the gas flow direction for several laser operational parameters described by gas pressure and input electrical power.     

An injection-locked single-mode tea CO2 laser for SMM laser pumping

A D₂O laser has been developed for collective Thomson scattering measurements of ion temperature in high temperature plasmas. A pulse duration and a spectral width of a high power D₂O laser has been successfully controlled for this purpose, by using a TEA CO₂ laser injection-locked by an etalon-tuned TEA CO₂ laser as a pump source.     

Principle of phase-locking of axisymmetric concentric cavity CO2 laser

Based on the phase-locking principle of Gaussian beam, the phase-locking mechanisms of the spherical wave from axisymmetric concentric cavity (ASCC) CO₂ laser are analyzed. And then we study the variety laws of the equiphase surfaces and the light spots of the injected beam. The numerical calculations show that the injected beam could be considered as a spherical wave approximately in the ASCC. The phase-locking of the spherical wave is different from the phase-locking of the Gaussian beam; there are different field distributions between Gaussian beam and spherical wave. And the phase-locking method could improve the maximum value of the light intensity, the encircled energy reflects the degree of phase-locking.     

Numerical modeling of a fast-axial-flow CW–CO2 laser

A four-temperature model has been applied on a fast axial flow, longitudinal discharge CO₂ laser. Using Runge–Kutta method, a set of differential equations of the model is numericaly solved. These equations describe the operation of the laser with certain ratio 1:3:6 of the mixture CO₂:N₂: He and average output power of 550 W.The temporal behaviour of the output power and photon density was obtained. The effects of kinetic temperature, coupled mirror reflectivity, gas flow speed, and cavity loss on the output power were studied.Calculated output power was compared with its measured value taken from experiment and a good agreement was observed.     

Numerical investigation of a fast-axial-flow CW CO2 laser

This paper presents the results of the calculation of the parameters of the active medium of a fast-axial-flow CO₂ laser using numerical methods in the framework of a one-dimensional approximation of the set of continuity equations, Bernoulli equation, equation of gas state, energy equation and multi-temperature rate equations with regard to diffusion for the gas flow in the cylindrical discharge tube. The spatial distribution of the small-signal gain and gas temperature along the gas flow direction have been calculated for a given set of initial conditions, namely, gas flow velocity, gas pressure and the tube diameter. In addition, the dependence of small-signal gain, the asymmetric stretch vibrational temperature of CO₂ (T₃) and the gas temperature on the discharge current were studied.     

High-power transverse flow CW CO2 laser for material processing applications

A transverse flow transversely excited (TFTE) CW CO₂ with a maximum output power about 15 kW has been developed. This is excited by pulser sustained DC discharge applied between a pair of multi-pins anodes and a common tubular cathode. Though the laser power in convective cooled CO₂ laser scales proportionally with the volumetric gas flow, it did not increase in this laser when the volumetric gas flow was increased by increasing the electrode separation keeping the flow velocity constant. The discharge voltage too remained almost unchanged with increase of the electrode separation. These observations are explained considering the electrical discharge being controlled by ionization instability. Laser materials processing applications often demand programming facilities for laser power modulation. A four-stage cascaded multilevel DC–DC converter-based high-frequency switch mode power supply has been developed to modulate the output power of the laser. Laser was operated up to 15 kW output power in four different modes viz. continuous wave mode, pulse periodic mode, single shot mode and processing velocity-dependent power mode with 1.2 kHz modulation bandwidth. We describe briefly the laser system, the SMPS, and the temporal behavior of laser beam.     

Experimental research on axisymmetric folded-combined cavity CO2 laser

Rationality and feasibility of axisymmetric folded-combined cavity CO₂ laser which is reported in this paper have been proved by principle experiments. The laser lays a foundation to manufacture higher power CO₂ lasers whose output power can easily reach 1 kW. Faculas at different positions in free space and facula of nine beams which pass through the beam focusing optics have been obtained. Analyses of the experimental results are made. These analyses lay a foundation for beam transformation, transmission and shaping.