PdO/TiO2 and Pd/TiO2 Heterostructured Nanobelts with Enhanced Photocatalytic Activity

Heterostructures play an important role not only in the manufacture of semiconductor devices, but also in the field of catalysis. Herein, we report the synthesis of PdO/TiO₂ and Pd/TiO₂ heterostructured nanobelts by means of a simple co‐precipitation method, followed by a reduction process using surface‐modified TiO₂ nanobelts as templates. The as‐obtained heterostructures were characterized by transmission electron microscopy, X‐ray photoelectron spectroscopy, and UV/Vis diffuse reflectance spectroscopy. PdO and Pd nanoparticles with a size of about 1.3 and 1.6 nm were assembled uniformly on the surface of TiO₂ nanobelts, respectively. Compared with TiO₂ nanobelts, PdO/TiO₂ and Pd/TiO₂ hybrid nanobelts exhibit enhanced photocatalytic activity upon UV and visible‐light irradiation. Photoelectrochemical technology was used to study the heterostructure effect on enhanced photocatalytic activity. Our mechanistic investigation revealed that energy‐band matching is the major factor in the observed enhancement of photocatalytic activity.     

低温静电自组装法制备贵金属修饰TiO_2纳米结构薄膜及其增强的光催化性能(英文)

以碱-水热法在金属Ti片上原位生长了TiO2纳米结构(纳米花和纳米线)薄膜,并采用低温静电自组装方法将超细贵金属(金、铂、钯)纳米颗粒均匀沉积于多孔TiO2薄膜上.负载于Ti片上的贵金属/TiO2纳米结构薄膜具有一体化结构、多孔架构和高光催化活性.超高分辨率场发射扫描电子显微镜(FESEM)直接观察表明贵金属纳米颗粒在TiO2表面分布均匀,且颗粒之间相互分离,金、铂、钯纳米颗粒的平均粒径分别约为4.0、2.0和10.0nm.俄歇电子能谱(AES)纵深成分分析表明贵金属不仅沉积于薄膜表面,且大量分布于TiO2纳米结构薄膜内部,其深度超过580 nm.X射线光电子能谱(XPS)分析表明,经300°C下在空气中热处理后,纳米金仍保持金属态,纳米铂部分被氧化成PtOabs,而钯粒子则完全被氧化成氧化钯(PdO).以低温静电自组装法沉积贵金属,贵金属负载量可通过调节组装时间与溶胶pH值来控制.光催化降解甲基橙的结果表明,沉积的纳米金和铂能显著增加TiO2纳米结构薄膜的光催化活性,说明金和铂粒子可促进光生载流子的分离;但负载的PdO对TiO2薄膜的光催化性能增强几乎无作用.     

Characterization of Pd/TiO2 embedded in multi-walled carbon nanotube catalyst with a high photocatalytic activity

Pd particles loading on TiO₂-embedded multi-walled carbon nanotubes (MWCNTs), MWCNTs, and TiO₂ particles were prepared via an impregnation method with palladium(II) chlorate solution followed by heat treatment at high temperature. To characterize the catalysts, BET surface area, scanning electron microscopy, transmission electron microscopy, X-ray diffraction, energy dispersive X-ray, Fourier transform infrared spectroscopy and ultraviolet-visible spectroscopy were employed. The prepared catalysts were tested in degradation of methyl orange under visible light. Pd/TiO₂-MWCNTs catalyst demonstrates the highest photocatalytic activity, and the phase transformation from PdO to Pd0 phase takes place at heat treatment of embedded TiO₂. The nanoparticles size of TiO₂ can be decreased by introduction of MWCNTs species. Combining structural characterization with kinetic study results we could conclude that the superior catalytic performance could arise due to the Pd/TiO₂-MWCNTs catalyst’s structure.     

Formation of Superhydrophobic-Superhydrophilic Pattern on Flowerlike Alumina Thin Film by the Sol-Gel Method

We have prepared superhydrophobic surfaces which become superhydrophilic by heat-treatment at 500°C or irradiation of UV-light. When hydrolyzed fluoroalkyltrimethoxysilane (FAS) was coated on Al₂O₃ gel film with a roughness of 20 to 50 nm, the films showed superhydrophobicity and high transparency; the contact angle for water of the film was 165° and the transmittance for the visible light was higher than 92%. When the FAS-coated thin films were heat-treated at temperatures higher than 500°C, the films became superhydrophilic; the contact angle for water on the films was smaller than 5°. Thin films of amorphous TiO₂ or anatase TiO₂ were coated between Al₂O₃ gel and FAS layer, and the contact angle for water was also about 160°. UV irradiation using high-pressure mercury lamp on these films resulted in the contact angle to be smaller than 5°. When UV light was irradiated through a photomask, superhydrophobic-superhydrophilic micropatterns applicable as a stamper for printing or a substrate of micro-optical components were successfully obtained on the films.     

Control of optical properties of gel-derived oxide coating films containing fine metal particles

Control of the optical properties of gel-derived oxide films containing fine metal particles is described. The duration of the aging of Si(OC₂H₅)₄-derived sols and the amount of water for hydrolyzing Si(OC₂H₅)₄ were found to greatly affect the size and the shape of Au particles formed in the silica matrix, and accordingly the optical absorption of the Au/SiO₂ composite films. Employing dielectric media with high refractive indices like TiO₂ was shown to shift the absorption peak of Au particles to longer wavelengths. Pd/TiO₂ and Pt/TiO₂ composite films showed absorption in the visible region.     

The photocatalytic properties of amorphous TiO2 composite films deposited by magnetron sputtering

The preparation of amorphous TiO₂ film coupled with various metal-oxide semiconductors and their photocatalytic activities evaluated by photo-degradation of methylene blue and rhodamine B aqueous solution are briefly reviewed. The proposed photoreaction mechanism of the amorphous composite semiconductor and the differences between amorphous TiO₂-based films and crystalline TiO₂ photocatalytic materials in terms of preparation and usage are addressed. The inactive intrinsic amorphous TiO₂ film coupled with various metal oxides were found to gain high photocatalytic activity. These dopants induce forming new energy levels in the band gap of TiO₂ to enhance the charge separation of the photoinduced electrons and holes and extend the light absorption of TiO₂-based photocatalytic films into the visible region. In addition, two different effects of coupling metal oxides have been proved: the introduction of oxides of W, Cr, V, Ag, and Mo can significantly increase the photo-reactivity of amorphous TiO₂ film, while the combination of oxides of Zr, Sn, Sb, Cu, Ta, Fe, and Ni cannot affect the inactivity of pure amorphous TiO₂ film.     

XPS and XANES studies of SnO<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript> nanolayers

This paper presents the results of our XPS (X-ray photoelectron spectroscopy) and XANES (X-ray absorption near edge structure) studies of tin oxide nanolayers obtained by magnetron spraying of the metal and its further oxidation in air at different temperatures. It was shown that at 240°C (annealing temperature), tin monoxide was dominant in the surface layer of the samples. When the temperature was increased to 450°C, the phase composition corresponded to tin dioxide. Increased sorption ability was found for the samples oxidized at 450°C. The band structure model of SnO _x nanolayers obtained by superposition of the XANES and XPS data revealed cross transitions with energy ～3.7 eV in the presence of the SnO and SnO₂ phases. Surface doping of nanolayers with palladium gave the Pd, PdO, and PdO₂ components, among which PdO was most intense. Alternate treatments with O₂ and H₂ gases led to the disappearance of palladium dioxide and the reduction of PdO to the Pd metal. After the volume doping of nanoplayers with palladium, the surface layer contained PdO and PdO₂; the latter was represented by two types of particles with different sizes.     

Solution Synthesis of Nano-Phase Nickel as Film and Porous Electrode

Routes to nano-phase nickel in the forms of highly porous sponges and dense films have been developed. Nickel acetate and nitrate were mixed with triethanolamine and methanol, and evaporated to a concentrated liquid. Heat-treatment at 10°C/min to 170°C under N₂ atmosphere yielded a highly porous sponge consisting of <10 nm sized Ni crystallites. Deposition of a 1 M nickel precursor solution on polycrystalline Al₂O₃, SnO₂ : F coated glass or titanium substrates spinning at 2700 rpm, followed by heat-treatment at 10°C/min to 400°C yielded smooth and dense nickel films consisting of 3–5 nm sized crystallites. The precursor concentrate was studied by FT-IR and the phase development on heat-treatment was studied by thermogravimetric analysis, powder X-ray diffraction, scanning and transmission electron microscopy.     

Electrical Properties of Transparent Doped Oxide Films

In the present study n-type and p-type transparent conductive TiO₂ films were prepared by using sol-gel method. The n-type TiO₂ films were obtained by using Ti(OC₃H ₇ ⁱ )₄ solutions co-doped with Ru and Ta. The films were uniform and transparent in all the conditions, and their crystalline phases were anatase when HCl or HNO₃ was used as a catalyst. The resistivity decreased with increasing Ta content and increased with increasing Ru content. Most of the films showed resistivity minima at a heat-treatment temperature of 700°C. The lowest resistivity of 10¹ 10² cm was attained. The p-type TiO₂ films were obtained by using Ti(OC₃H ₇ ⁱ )₄ solutions co-doped with Co and Nb (Sb). The films were also uniform and transparent when AcAc was used, while samples heat-treated at 800°C became opaque when HCl was added. Rutile single phase appeared when the films were heat-treated at 700°C. Logarithmic resistivity of films co-doped with Co and Nb was directly proportional to the reciprocal absolute temperature. On the other hand, the slopes for films co-doped with Co and Sb were different below and above 200°–220°C. The activation energy at the low-temperature region is as low as 0.17 eV, and the resistivity at room temperature is 10⁴ 10⁵ cm.     

The Preparation and Characterization of Highly Dispersed PdO over Alumina for Low‐temperature Combustion of Methane

PdO/Al₂O₃ catalysts prepared by glow discharge plasma treatment followed by thermal calcination show a much higher dispersion and a better catalytic activity for methane combustion at relatively low temperatures. The dispersion of palladium active species by such plasma prepared catalysts is 29.7%, 5.4 times higher than that of conventional catalysts. XPS analysis indicates that a surface enrichment of Pd active species (PdO) has been achieved after plasma treatment. The surface atomic composition of PdO of plasma prepared catalysts reaches 10.5%. XRD characterization also confirms a wellcrystallized PdO phase present on the plasma prepared catalyst. The lightoff temperature of the plasma prepared catalyst is 370°C, 50°C lower than that obtained from the conventional catalyst.     

Structural Changes in Sol-Gel Derived SiO2 and TiO2 Films by Exposure to Water Vapor

Structural changes in sol-gel derived thin films by exposure to water vapor were investigated using Fourier transform infrared absorption spectroscopy, ellipsometry and x-ray diffraction. We found that SiO₂ gel films were densified with a decrease in OH groups by the exposure at 60°–180°C. The shrinkage and the peak frequency of ₄ (TO) for the exposed films were comparable to those heated in a dry atmosphere at temperatures above 500°C. However, OH groups in the films were not completely removed by the water exposure. A subsequent annealing above 300°C changed the structure of the water-exposed SiO₂ films with condensation of the remaining OH groups. Although the exposed SiO₂ gel films were amorphous, TiO₂ gel films were transformed to anatase with a decrease in OH groups by the treatments at 80°–180°C.     

Effect of Prefiring Condition on the In-Plane Orientation of Epitaxial Oxide Films in Coating-Pyrolysis Process

Epitaxial -Fe₂O₃ films were obtained by using iron 2-ethylhexanoate as a starting material. A coating solution was spun on -Al₂O₃ single-crystal substrates, and prefiring and final heat-treatment at various temperatures in air or low oxygen partial pressure were carried out. The degree of in-plane orientation was estimated in terms of full width at half maximum of X-ray diffraction (XRD) -scans. The results of TG-DTA, IR, and XRD suggested that the optimum prefiring condition for obtaining highly epitaxial films is in the range 200–300°C which corresponds to removal of most of the organic component from the precursor, prior to crystallite formation of metal oxide. When the films were prefired at higher temperatures, different atmospheres in prefiring and final heat-treatment lowered the in-plane orientation of the films.     

Nano-titanium oxide doped with gold,silver, and palladium — synthesis and structural characterization

Nano-titania doped with noble metals (Au/TiO₂, Ag/TiO₂, Pd/TiO₂) has been synthesized by mild hydrolysis of the mixture of metal salts or complexes and titanium isopropoxide ((iPr-O)₄Ti). After thermal decomposition of the obtained precursors, nanomaterials were formed. Morphological characterization of the nanomaterials was provided by scanning electron microscopy (SEM) and stereological analysis, determining the BET specific surface area, and BJH nanoporosity (pore volume, pore size). It has been found that the structure of nanomaterials (size of nanoparticles and agglomerates) depended strongly on the method of the (iPr-O)₄Ti hydrolysis. A minor dependence on the kind of solvents and precursors of noble metals was observed. The presence of doping metal nanoparticles was confirmed by transmission electron microscopy (TEM) and energy dispersive X-ray spectroscopy (EDX). Nanomaterial phases were identified by X-ray diffraction (XRD). According to the XRD patterns, Ag/TiO₂ and Pd/TiO₂ products with doping metals in their oxidized form contain Ag-Ti and Pd-Ti phases. Peaks of the metal oxides Ag₂O and PdO are absent in the XRD patterns. The average size of TiO₂ nanoparticles is situated in the region of 20–60 nm, whereas metals are present as about 10–15 nm sized particles and fine nanoparticles.     

Preparation and Characterization of TiO2 Thin Films by Sol-Gel Method

Titanium dioxide (TiO₂) thin films have been deposited on silicon and glass substrates by the sol-gel process using titanium iso-propoxide [Ti(O-i-C₃H₇)₄]. The bond configuration of the TiO₂ thin films was analyzed by using FTIR in the wavenumber range from 400 to 4000 cm^–1. The spectral transmittance of as-deposited TiO₂ films deposited on fused silica glass was measured in the wavelength range from 200 to 900 nm. X-ray diffraction measurements were performed to determine the crystallinity of the TiO₂ films. As-deposited films were amorphous. As the film was annealed at higher temperature, the structure was transformed from amorphous to the anatase crystalline state. The chemical composition of the deposited film was investigated using X-ray photoelectron spectroscopy (XPS). The films are essentially stoichiometric with carbon as the dominant impurity on the surface. Raman spectra show the characteristic of TiO₂ anatase phase. The electrical properties of the TiO₂ films were measured using capacitance-voltage (C-V) and current-voltage techniques. From C-V measurements, the dielectric constants were calculated to be approximately 26 for the as-deposited films and 75–82 for films annealed at 700°C in different atmosphere. For the as-deposited samples, the breakdown voltage was 2.7 MV/cm, and for an electric field of 1 MV/cm, the leakage current was 5 × 10^–5 A/cm² and the resistivity was 2.2 × 10¹⁰ -cm.     

A comparison between two Pd‐Ni catalysts supported on two different supports toward Suzuki‐Miyaura coupling reaction

When a single metal fails to promote an efficient Suzuki‐Miyaura coupling reaction at ambient temperature, the synergistic cooperation of two distinct metals might improve the reaction. To examine the synergistic effect of palladium and nickel for catalyzing Suzuki coupling reaction, g‐C₃N₄ supported metal nanoparticles of PdO, NiO and Pd‐PdO‐NiO were prepared, characterized and their catalytic activities evaluated over different aryl halides at room temperature and 78 °C. The morphological characterization of Pd‐PdO‐NiO/g‐C₃N₄ demonstrated that the bimetallic particles were uniformly dispersed over the g‐C₃N₄ layers with diameters ranging from 3.5‐7.7 nm. XPS analysis showed that nanoparticles of Pd‐PdO‐NiO consisted of Pd(II), Pd(0) and Ni(II) sites. The experiments performed on the catalytic activity of Pd‐PdO‐NiO/g‐C₃N₄ showed that the prepared catalyst demonstrated an efficient activity without using toxic solvents.     

PMMA films refractive index modulation via TiO2 nanoparticle inclusions and corona poling

The present study is focused on the characterization of optical properties of poly (methyl methacrylate) (PMMA) films and the possibilities of modulation and fine tuning of their refractive index by the inclusion of different concentrations of nano-sized titanium dioxide (TiO₂) particles (less than 33 nm) and corona poling. The samples are prepared by the “spin coating” method and they are charged in a conventional point-to-plain corona system. The transparent PMMA/TiO₂ films exhibit good optical properties in the visible range. An investigation of the film’s surface refractive index by two wavelengths laser refractometry utilizing the disappearing diffraction pattern method is carried out. The refractive index increases with increasing the TiO₂ content in the nanocomposite films. The corona poling increases the refractive index values for all samples regardless of the polarity and concentration of TiO₂ nanoparticles. The results show that the prepared nanocomposite films have a potential application for optical devices.     

Atomic Force Microscopic Studies of Porous TiO2 Thin Films Prepared by the Sol-Gel Method

Porous titanium dioxide thin films were prepared from alkoxide solutions with and without polyethylene glycol (PEG) by the sol-gel method on soda-lime glass. The effects of PEG addition to the precursor solution on the microstructure and roughness of the resultant thin films were investigated by atomic force microscopy (AFM). It was found that TiO₂ films prepared from the precursor solution without PEG had granular microstructure and flat texture, and was composed of about 100 nm spherical particles. With an increase in the times of coating cycles, the roughness of films decreased and the size of TiO₂ particles increased. On the other hand, the larger the amount and molecular weight of the added PEG in precursor solutions, the larger the diameter and the depth of pores in the resultant films on the decomposition of PEG during heat-treatment. The surface of the films was also rougher, and fewer pores were produced during heat-treatment. The mechanism of porous structure formation in the TiO₂ films was explained using the principle of spinodal phase separation.     

Influence of the Support on the Catalytic Characteristics of the Deposited Palladium in the Liquid-Phase Hydrogenation of Diphenylacetylene

Palladium catalysts on various types of supports were studied in the liquid-phase hydrogenation of diphenylacetylene. Samples of Pd/SiO₂–Al₂O₃, Pd/MgAl₂O₄, Pd/Al₂O₃, and Pd/TiO₂ were characterized by the chemisorption of the CO and IR spectroscopy of adsorbed CO. The use of n-hexane as the solvent increases the reaction rate, which can be explained by the better solubility of hydrogen in the liquid phase. It is established that the acid–base properties of the support do not affect the activity and selectivity of the catalysts in the reaction under study. However, they alter the electronic state of palladium. According to the catalytic tests, Pd/TiO₂ has the highest activity (turnover frequency) and selectivity to alkene. The comparison of the obtained catalytic data and the results of IR spectroscopy made it possible to conclude that this is due to the electron density redistribution between the palladium and TiO _x particles, which is caused by the strong metal–support interaction.     

Anodic Dissolution of Palladium in Sulfuric Acid: An Electrochemical Quartz Crystal Microbalance Study

Regularities of formation of a palladium oxide layer and its cathodic reduction in 0.5 M H₂SO₄ at 0.5–1.3 V (SHE) are studied by cyclic voltammetry, x-ray photoelectron spectroscopy, and electrochemical quartz crystal microbalance. A pure Pd plate and a 0.5-m-thick Pd coating on gold-sputtered quartz crystal is used for electrochemical and microgravimetric studies. It is shown that a Pd electrode dissolves electrochemically in 0.5 M H₂SO₄ when its potential is cycled between 0.5 and 1.3 V. In the case of 0.5-m-thick Pd coating on the gold substrate, the decrease in the electrode weight during one anodic–cathodic cycle is 1.0–1.5 g/cm². It is suggested that anodic process at 0.5–1.3 V (SHE) represents electrochemical oxidation of palladium, yielding a surface layer of poorly soluble Pd(OH)₂ and/or PdO phases, as expressed by the equation Pd + 2H₂O (Pd(OH)₂/PdO)_s + 2H⁺ + 2e. This surface layer, (Pd(OH)₂/PdO)_s, undergoes reduction during the cathodic process. About 5% of the total amount of ionized palladium dissolve in electrolyte.     

Low-temperature sol–gel synthesis of anatase nanoparticles modified by Au, Pd and Pt and activity of TiO2/Au, Pd, Pt photocatalysts in water splitting

Base catalyzed hydrolysis and condensation of Ti isopropoxide with water at ambient temperature and molar ratio H₂O/Ti(i-PrOH)₄ varied from 1 to 100 was studied. It was found that molar ratio H₂O/Ti(i-PrOH)₄ = 100 originated amorphous TiO₂-precursor of summary composition TiO_1.9(OH)_0.2 with a specific surface area of 354 m²/g. Low-temperature crystallization of amorphous TiO₂-precursor to nanostructured anatase at 80 °C in a slightly reducing environment of d-glucose was studied. It was found that the low-temperature nucleation and crystallization of anatase was initiated (activated) by combined effects of d-glucose and Au⁰, Pd⁰ and Pt⁰ nanoparticles, generated in situ by slow reduction of Au³⁺, Pd²⁺ and Pt⁴⁺ ions using d-glucose. Considerable photocatalytic activity of Ti-hydroxide-oxide/Au, Pd, Pt catalysts prepared at low-temperature was associated with high content of nanostructured anatase and low content of Au, Pd and Pt nanoparticles (0.02 wt.%) effectively deposited on the surface of titania particles. The maximum hydrogen evolution rates 3.4 μmol/min g at Ti-hydroxide-oxide/Au, 4.0 μmol/min g at Ti-hydroxide-oxide/Pd and 4.1 μmol/min g at Ti-hydroxide-oxide/Pt were found. The activity of all TiO₂/Au, Pd and Pt catalysts increased by calcination at 600 °C from 50 to 100 %.