Hydrophobic thin fluoropolymer coating on cotton surfaces

We report a simple novel procedure to prepare hydrophobic cotton textiles by admicellar polymerization. By in situ introducing fluoropolymer on cotton fibers to generate a dual-size surface roughness, followed by hydrophobization with a little amount of fluoromonomer Octafluoropentamethyl methacrylate (OFPM) with short time, normally hydrophilic cotton has been easily turned into hydrophobic. Hydrophobic cotton textile exhibits a static water contact angle of 124° for a 10?µl droplet. When an octa fluoroalkyl chain is introduced to the cotton surface, the originally smooth surface changed immediately to rough surface which is the key factor for hydrophobicity like lotus leaves.     

Construction of simple gold nanoparticle aggregates with controlled plasmon–plasmon interactions

We have developed a colloidal assembly for the study of plasmon–plasmon interactions between gold nanoparticles. Colloidal aggregates of controlled size and interparticle spacing were synthesized on silica nanoparticle substrates. Following the immobilization of isolated gold nanoparticles onto silica nanoparticles, the surfaces of the adsorbed gold nanoparticles were functionalized with 4-aminobenzenethiol. This molecular linker attached additional gold nanoparticles to the ‘parent' gold nanoparticle, forming small nanoparticle aggregates. The optical absorption spectrum of these clusters differed from that of gold colloid in a manner consistent with plasmon–plasmon interactions between the gold nanoparticles.     

In-situ growth of silica nanoparticles on cellulose and application of hierarchical structure in biomimetic hydrophobicity

Monodispersed silica nanoparticles were prepared by a simple two-step method with hydrolysis and condensation. The materials were characterized by dynamic light scattering (DLS), SEM and TEM. Through in-situ growth of silica nanoparticles on cotton fabrics, a dual-scaled surface with nanoscaled roughness of silica and microscaled roughness of cellulose fiber was generated. After the modification of the low surface energy, the wettability of smooth silicon slide, silicon slide with nanoscaled roughness of silica particles, cotton fabric, and cotton fabric with silica particles was evaluated by the tests of the contact angle (CA) and the advancing and receding contact angle (ARCA). The cotton fabric with dual-scaled roughness exhibits a static CA of 149.8° for 4 μL water droplet and a hysteresis contact angle (HCA) of 1.8°. The results of CA and HCA show that microscaled roughness plays a more important role than nanoscaled roughness for the value of CA and HCA. The results in the hydrostatic pressure test and the rain test show the important contribution of nanoscaled roughness for hydrophobicity.     

Silica nanoparticle size influences the structure and enzymatic activity of adsorbed lysozyme

Adsorption of chicken egg lysozyme on silica nanoparticles of various diameters has been studied. Special attention has been paid to the effect of nanoparticle size on the structure and function of the adsorbed protein molecules. Both adsorption patterns and protein structure and function are strongly dependent on the size of the nanoparticles. Formation of molecular complexes is observed for adsorption onto 4-nm silica. True adsorptive behavior is evident on 20- and 100-nm particles, with the former resulting in monolayer adsorption and the latter yielding multilayer adsorption. A decrease in the solution pH results in a decrease in lysozyme adsorption. A change of protein structure upon adsorption is observed, as characterized by a loss in alpha-helix content, and this is strongly dependent on the size of the nanoparticle and the solution pH. Generally, greater loss of alpha helicity was observed for the lysozyme adsorbed onto larger nanoparticles under otherwise similar conditions. The activity of lysozyme adsorbed onto silica nanoparticles is lower than that of the free protein, and the fraction of activity lost correlates well with the decrease in alpha-helix content. These results indicate that the size of the nanoparticle, perhaps because of the contributions of surface curvature, influences adsorbed protein structure and function.     

Bacterial adhesion inhibition of the quaternary ammonium functionalized silica nanoparticles

Quaternary ammonium compounds have been considered as excellent antibacterial agents due to their effective biocidal activity, long term durability and environmentally friendly performance. In this work, 3-(trimethoxysilyl)-propyldimethyloctadecylammonium chloride as a quaternary ammonium silane was applied for the surface modification of silica nanoparticles. The quaternary ammonium silane provided silica surface with hydrophobicity and antibacterial properties. In addition, the glass surface which was coated with the surface modified silica nanoparticles presented bacterial growth inhibition activity. For comparison of bacterial growth resistance, hydrophobic silane (alkyl functionalized silane) modified silica nanoparticles and pristine silica nanoparticles were prepared. As a result of bacterial adhesion test, the quaternary ammonium functionalized silica nanoparticles exhibited the enhanced inhibition performance against growth of Gram-negative Escherichia coli (96.6%), Gram-positive Staphylococcus aureus (98.5%) and Deinococcus geothermalis (99.6%) compared to pristine silica nanoparticles. These bacteria resistances also were stronger than that of hydrophobically modified silica nanoparticles. It could be explained that the improved bacteria inhibition performance originated from the synergistic effect of hydrophobicity and antibacterial property of quaternary ammonium silane. Additionally, the antimicrobial efficacy of the fabricated nanoparticles increased with decreasing size of the nanoparticles.     

Physical and optical properties of organo-modified silica nanoparticles prepared by sol–gel

A comparative study on the physical and optical properties of silica nanoparticles prepared by sol–gel has been carried out. Post-modification of as-synthesized silica nanoparticles produced organo-functionalized silica nanoparticles slightly increased in size (~20%) and relatively high aggregation. However, in situ method produced sixfold bigger functionalized particles with good dispersion and less aggregation. Higher organic content was observed for in situ modified nanosilica, leading to a higher surface hydrophobicity that improved compatibility and dispersion in preparation of silica-polymer nanocomposite. Furthermore, in situ and post-modified nanosilica demonstrated a distinct optical activity, photoluminescence and UV compared to the unmodified nanoparticles.     

Synthesis and characterization of functionalized silica as fillers of polymeric systems

This study investigates the functionalization of sol-gel silica with selected organic species, and compares the materials obtained to a commercially available silica functionalized under comparable conditions. Anilines with different active groups were grafted onto the surface of the silicas, via reaction with key surface sites, to modulate the hydrophobicity of the materials. The properties of the functionalized materials, as determined by FT-IR, DTA-TGA and nitrogen adsorption (surface area, S_BET) are discussed.     

Highly transparent superhydrophobic surfaces from the coassembly of nanoparticles (≤100 nm)

We report a simple and versatile approach to creating a highly transparent superhydrophobic surface with dual-scale roughness on the nanoscale. 3-Aminopropyltrimethoxysilane (APTS)-functionalized silica nanoparticles of two different sizes (100 and 20 nm) were sequentially dip coated onto different substrates, followed by thermal annealing. After hydrophobilization of the nanoparticle film with (heptadecafluoro-1,1,2,2-tetrahydrodecyl)trichlorosilane for 30 min or longer, the surface became superhydrophobic with an advancing water contact angle of greater than 160° and a water droplet (10 μL) roll-off angle of less than 5°. The order of nanoparticles dip coated onto the silicon wafer (i.e., 100 nm first and 20 nm second or vice versa) did not seem to have a significant effect on the resulting apparent water contact angle. In contrast, when the substrate was dip coated with monoscale nanoparticles (20, 50, and 100 nm), a highly hydrophobic surface (with an advancing water contact angle of up to 143°) was obtained, and the degree of hydrophobicity was found to be dependent on the particle size and concentration of the dip-coating solution. UV-vis spectra showed nearly 100% transmission in the visible region from the glass coated with dual-scale nanoparticles, similar to the bare one. The coating strategy was versatile, and superhydrophobicity was obtained on various substrates, including Si, glass, epoxy resin, and fabrics. Thermal annealing enhanced the stability of the nanoparticle coating, and superhydrophobicity was maintained against prolonged exposure to UV light under ambient conditions.     

Silica/Silicone Nanofilament Hybrid Coatings with Almost Perfect Superhydrophobicity

A facile method for the preparation of silica/silicone nanofilament hybrid coatings with almost perfect superhydrophobicity (contact angle=179.8° and sliding angle=1.3°) is presented. The coatings are obtained by dip‐coating of silica nanoparticles, followed by chemical vapor deposition of silicone nanofilaments. Predominant growth of silicone nanofilaments onto aggregated silica nanoparticles generates a two‐tier structure. The effect of silica nanoparticle size on the growth of silicone nanofilaments, along with their anti‐wetting properties and transparency are investigated in detail. Surface roughness and anti‐wetting properties can be simply regulated by controlling the size of silica nanoparticles.     

Surface modification of silica nanoparticles to reduce aggregation and nonspecific binding

In this article, a systematic study of the design and development of surface-modification schemes for silica nanoparticles is presented. The nanoparticle surface design involves an optimum balance of the use of inert and active surface functional groups to achieve minimal nanoparticle aggregation and reduce nanoparticle nonspecific binding. Silica nanoparticles were prepared in a water-in-oil microemulsion and subsequently surface modified via cohydrolysis with tetraethyl orthosilicate (TEOS) and various organosilane reagents. Nanoparticles with different functional groups, including carboxylate, amine, amine/phosphonate, poly(ethylene glycol), octadecyl, and carboxylate/octadecyl groups, were produced. Aggregation studies using SEM, dynamic light scattering, and zeta potential analysis indicate that severe aggregation among amine-modified silica nanoparticles can be reduced by adding inert functional groups, such as methyl phosphonate, to the surface. To determine the effect of various surface-modification schemes on nanoparticle nonspecific binding, the interaction between functionalized silica nanoparticles and a DNA chip was also studied using confocal imaging/fluorescence microscopy. Dye-doped silica nanoparticles functionalized with octadecyl and carboxylate groups showed minimal nonspecific binding. Using these surface-modification schemes, fluorescent dye-doped silica nanoparticles can be more readily conjugated with biomolecules and used as highly fluorescent, sensitive, and reproducible labels in bioanalytical applications.     

Hydrotalcite and nanometric silica as finishing additives to enhance the thermal stability and flame retardancy of cotton

Suspensions of nanoparticles (namely, hydrotalcite and nanometric silica) have been employed during the finishing of cotton in order to improve its thermal stability and/or flame retardancy. The immersion approach has also been coupled to a surface pre-treatment of the textile by cold oxygen plasma in order to load a higher amount of nanoparticles onto fibres. The time of immersion and the resulting distribution of the nanoparticles onto the fibres, evaluated by scanning electron microscopy in combination with elemental analysis, have been thoroughly investigated. The present study has shown that the above parameters are functions of nanoparticle type. Pre-treatment by cold plasma has been found to be more effective than the immersion only. As far as the thermal stability and the combustion behaviour of treated cotton are concerned, the nanoparticles turned out to be able to delay the degradation in air, modifying mechanism and kinetics, and at the same time enhancing the flame retardancy of cotton by increasing the time to ignition and decreasing the heat release rate peak during the combustion. The joint effect of the two nanoparticles has also been evaluated and found more efficient than the effect of single species.     

乙烯基Ia3d介孔硅分子筛的环氧化及其固定化青霉素酰化酶(英文)

采用直接共聚法合成表面含有乙烯基的具有立方相Ia3d结构的介孔硅分子筛(V-ClMS),然后对乙烯基团进行环氧化制备得到表面环氧基功能化的介孔硅分子筛(E-CIMS),采用X射线衍射、N2吸附-脱附、透射电镜、热重分析和13C固体核磁共振对制备的介孔硅分子筛进行了表征.结果表明,表面含有乙烯基的V-ClMS介孔硅分子筛能被一步成功合成,并易于发生环氧化而获得表面环氧基功能化的E-CIMS介孔硅分子筛.将E-CIMS介孔硅分子筛作为载体用于固定化青霉素G酰化酶(PGA),研究了表面环氧基团对固定化PGA初活性和操作稳定性的影响.结果表明,随着表面环氧基团数量的增加,介孔硅分子筛孔径减小,表面疏水性增加,导致载酶量和初活性减小.但介孔硅分子筛表面适量的环氧基团能增强E-CIMS介孔硅分子筛与PGA之间的相互作用,从而提高固定化PGA的操作稳定性.     

Synthesis of well-defined, polymer-grafted silica nanoparticles via reverse ATRP

The surface grafting onto ultrafine silica via reverse ATRP of methyl methacrylate initiated by peroxide groups introduced onto the surface and conventional ATRP of Styrene initiated by the hybrid nanoparticles were investigated. The introduction of peroxide groups onto the silica surface was achieved by the reaction of hydrogen peroxide with chlorosilyl groups, which were introduced by the treatment of silica with thionyl chloride. Well-defined polymer chains were grown from the nanoparticle surfaces to yield individual particles composed of a silica core and a well-defined, densely grafted outer polymer layer. The polymerization was closely controlled in solution at quite low temperature such as 70 °C. In both cases, linear kinetic plots, linear plots of molecular weight (M_n) versus conversion, in hydrodynamic diameter with increasing conversion, and narrow molecular weight distributions (M_w/M_n) for the grafted polymer samples were observed. Hydrolysis of silica cores by hydrofluoric acid treatment enabled characterization of cleaved polymer using GPC. Ultrathin films of hybrid nanoparticles were examined using TEM and AFM.     

Surface Chemistry of Nanohybrids with Fumed Silica Functionalized by Polydimethylsiloxane/Dimethyl Carbonate Studied Using 1H, 13C,and 29Si Solid-State NMR Spectroscopy

The investigation of molecular interactions between a silica surface and organic/inorganic polymers is crucial for deeper understanding of the dominant mechanisms of surface functionalization. In this work, attachment of various depolymerized polydimethylsiloxanes (PDMS) of different chain lengths, affected by dimethyl carbonate (DMC), to silica nanoparticles pretreated at different temperatures has been studied using ²⁹Si, ¹H, and ¹³C solid-state NMR spectroscopy. The results show that grafting of different modifier blends onto a preheated silica surface depends strongly on the specific surface area (SSA) linked to the silica nanoparticle size distributions affecting all textural characteristics. The pretreatment at 400 °C results in a greater degree of the modification of (i) A-150 (SSA = 150 m²/g) by PDMS-10/DMC and PDMS-1000/DMC blends; (ii) A-200 by PDMS-10/DMC and PDMS-100/DMC blends; and (iii) A-300 by PDMS-100/DMC and PDMS-1000/DMC blends. The spectral features observed using solid-state NMR spectroscopy suggest that the main surface products of the reactions of various depolymerized PDMS with pretreated nanosilica particles are the (CH₃)₃SiO-[(CH₃)₂SiO-]_x fragments. The reactions occur with the siloxane bond breakage by DMC and replacing surface hydroxyls. Changes in the chemical shifts and line widths, as shown by solid-state NMR, provide novel information on the whole structure of functionalized nanosilica particles. This study highlights the major role of solid-state NMR spectroscopy for comprehensive characterization of functionalized solid surfaces.     

喷涂法构筑二氧化硅纳米粒子涂层及其光学和润湿性质

采用Stöber方法,通过调节反应温度及乙醇和水的体积,合成了不同粒径的二氧化硅纳米粒子.以合成的粒径为20 nm的二氧化硅纳米粒子为原料,采用简单、方便的喷涂方法在玻璃片上构筑了纳米粒子涂层.在550 ℃煅烧二氧化硅纳米粒子涂层,增强了二氧化硅纳米粒子在玻璃片上的附着力.用1H, 1H, 2H, 2H-全氟辛基三乙氧基硅烷修饰之后,二氧化硅纳米粒子涂层的表面润湿性由亲水性转变为疏水性.通过喷涂法制备的二氧化硅纳米粒子涂层具有减反增透效果,当二氧化硅纳米粒子质量分数为0.48%、循环喷涂沉积数为3时,涂层在可见光范围内的最大透光率可达95.5%.用扫描电子显微镜观测涂层表面形貌发现,喷涂法制备的涂层是均匀的、可控的.喷涂技术构筑纳米粒子涂层具有简单快速、可大面积应用等优点.     

Liquid-phase Reductive Deposition as Novel Preparation Method for Highly Dispersive Nickel Catalysts

We have been developing the selective deposition method onto TiO₂ nanoparticles, named as the liquid-phase selective-deposition method, where TiO₂ plays a role of formation center of Ni nanoparticles as well as protection from the aggregative growth of the particles. The concept of this method is to well disperse and stabilize Ni nanoparticles on TiO₂ surface by specific adsorption of Ni precursory complexes and then heterogeneous nucleation on the adsorption sites. The particle size was decreased with increasing the amount of Zn added, thus the catalytically active Ni surface area was increased. The selective deposition onto TiO₂ surface and addition of Zn to the nanoparticle promoted the catalytic activity of Ni–Zn nanoparticle, e.g. the catalytic activity of Ni–Zn/TiO₂ was ca. 10 times higher than that of the unsupported Ni nanoparticles. Ni in the nanocomposite was assigned as metallic, although their surface was oxidized under the atmospheric condition, but Zn and B were deposited as their oxide.     

Preparation of durable superhydrophobic surface by sol–gel method with water glass and citric acid

Durable superhydrophobic surface on cotton fabrics has been successfully prepared by sol–gel method. Cellulose fabric was first coated with silica sol prepared with water glass and citric acid as the acidic catalyst. The silica coated fabric was then padded with hydrolyzed hexadecyltrimethoxysilane afterwards obtaining low surface energy. Water contact angle and hydrostatic pressure were used to characterize superhydrophobicity and washing durability. Scanning electron microscopy was used to characterize the surface morphology changes after certain washing times. All results showed good durable hydrophobicity on cellulose fabrics. In addition, the influence of citric acid and sodium hypophosphite (NaH₂PO₂) on the durability of hydrophobicity was also investigated. The durability of treated cotton improved with the increase of concentration of citric acid in the presence of NaH₂PO₂. It could be concluded that citric acid acted as multi-functional heterogeneous grafting chemicals to improve washing durability of hydrophobicity by forming the ester bonds between cotton fabric and silica sol and improved the durability of hydrophobicity.     

Biomimetic superhydrophobic and highly oleophobic cotton textiles

We report a biomimetic procedure to prepare superhydrophobic cotton textiles. By in situ introducing silica particles to cotton fibers to generate a dual-size surface roughness, followed by hydrophobization with polydimethylsiloxane (PDMS), normally hydrophilic cotton has been easily turned superhydrophobic, which exhibits a static water contact angle of 155 degrees for a 10 microL droplet. The roll-off angle of water droplets depends on the droplet volume, ranging from 7 degrees for a droplet of 50 microL to 20 degrees for a 7 microL droplet. When a perfluoroalkyl chain is introduced to the silica particle surface, the superhydrophobic textile also becomes highly oleophobic, as demonstrated by a static contact angle of 140 degrees and a roll-off angle of 24 degrees for a 15 microL sunflower oil droplet.     

Strong cellulose nanofibre–nanosilica composites with controllable pore structure

Flexible nanocellulose composites with silica nanoparticle loading from 5 to 77 wt% and tunable pore size were made and characterised. The pore structure of the new composites can be controlled (100–1000 nm to 10–60 nm) by adjusting the silica nanoparticle content. Composites were prepared by first complexing nanoparticles with a cationic dimethylaminoethyl methacrylate polyacrylamide, followed by retaining this complex in a nanocellulose fibre network. High retention of nanoparticles resulted. The structural changes and pore size distribution of the composites were characterised through scanning electron microscopy (SEM) and mercury porosimetry analysis, respectively. The heavily loaded composites formed packed bed structures of nanoparticles. Film thickness was approximately constant for composites with low loading, indicating that nanoparticles filled gaps created by nanocellulose fibres without altering their structure. Film thickness increased drastically for high loading because of the new packed bed structure. Unexpectedly, within the investigated loading range, the level of the tensile index on nanocellulose mass basis remained constant, showing that the silica nanoparticles did not significantly interfere with the bonding between the cellulose nanofibres. This hierarchically engineered material remains flexible at all loadings, and its unique packing enables use in applications requiring nanocellulose composites with controlled pore structure and high surface area.     

Preparation and synergetic catalytic effects of amino-functionalized MCM-41 catalysts

Four amine functionalized mesoporous catalysts were synthesized by grafting primary, dualistic and two secondary amines onto the channel walls of mesoporous silica, MCM-41. We examined the effects of organoamine loading amount on the acid-base synergism of the catalysts in the self-condensation reaction of n-butanal, a Knoevenagel condensation and a Henry reaction. We observed the balance of the amine and residual silanol amounts is crucial to the catalytic performances of the functionalized mesoporous catalysts. An optimum organoamine loading amount exists, which is dependent on the organoamine type. There is little difference in the optimum organoamine loading amount between different reactions. The secondary organoamine functionalized MCM-41 exhibits the best catalytic performance in the experimental range.