丙烯酸树脂／蒙脱土纳米复合材料的制备研究

采用离子交换法,用十六烷基三甲基溴化铵对钠基蒙脱土(Na-MMT)进行改性制备了有机蒙脱土(OMMT).用丙烯酸(AA)、硫酸化蓖麻油、乳化剂OP-10、过硫酸钾为原料进行水溶液聚合制得丙烯酸树脂.将丙烯酸树脂与改性蒙脱土通过聚合插层制备了丙烯酸树脂/ 蒙脱土纳米复合材料.通过傅立叶变换红外(FTIR)和X-射线衍射 (XRD)等手段对复合材料的结构进行了表征,结果表明:丙烯酸树脂插层进入有机蒙脱土内可形成插层型或剥离型的纳米复合材料.蒙脱土含量及蒙脱土与丙烯酸树脂的反应温度、反应时间均对复合材料的剥离行为产生影响,在蒙脱土含量为树脂固含量的7%、温度为70℃、反应4h的条件下可得到完全剥离的纳米复合材料.     

甲苯-2,4-二异氰酸酯修饰蒙脱土及聚苯乙烯蒙脱土纳米复合材料的制备与表征

用FTIR和WAXD法研究了甲苯-2,4-二异氰酸酯(TDI)的邻位和对位异氰酸酯基团与蒙脱土表面羟基的修饰反应,在此基础上提出了结构模型;用TDI修饰后的蒙脱土成功制备了插层型聚苯乙烯/蒙脱土纳米复合材料,并用WAXD和TEM进行了表征.实验结果表明,修饰后TDI与蒙脱土表面形成化学键,使蒙脱土的片层间距显著增大,十六烷基三甲基溴化铵(CTAB)在蒙脱土层间由双层平行排列转变为双层脂肪链倾斜方式排列.在苯乙烯插层聚合过程中,蒙脱土层间距进一步扩大,其初级粒子在聚苯乙烯基体中的厚度约20～50nm.     

聚苯乙烯/硅烷偶联剂修饰蒙脱土纳米复合材料的制备与表征

用硅烷偶联剂修饰蒙脱土，制备了聚苯乙烯/蒙脱土纳米复合材料，并用XRD、FTIR、TEM和TGA等对样品进行了表征，发现硅烷偶联剂对蒙脱土表面进行了良好的修饰；苯乙烯单体在蒙脱土层间的聚合导致蒙脱土片层剥离并无规分散在聚合物基体中，片层长度为100-200nm，厚度小于10nm。     

双单体原位接枝插层法制备聚丙烯纳米复合材料的研究Ⅰ.制备、表征及力学性能的研究

用有机插层剂处理蒙脱土原土 ,制得有机蒙脱土 (O MMT) .采用双单体 (马来酸酐和苯乙烯 )原位接枝插层法 ,制备了聚丙烯 蒙脱土纳米复合材料母料 .将母料与聚丙烯基体在双螺杆上共混挤出 ,制得聚丙烯 蒙脱土纳米复合材料 (PP Montmorillonetenanocomposites,PMNC) .这是制备聚合物纳米复合材料的一种新方法 .通过X 射线衍射测试 (XRD)表明 ,有机蒙脱土片层 0 0 1面间距从原土的 1 4 9nm扩大到 2 96nm ,复合材料中蒙脱土片层 0 0 1面间距由有机蒙脱土的 2 96nm扩大到 4 0nm .力学性能测试表明 ,复合材料的力学性能明显优于PP基体 ,在提高材料拉伸强度的同时 ,缺口冲击强度也得到很大的提高 .用扫描电镜 (SEM)对材料的冲击断面形貌进行了研究 ,并从理论上分析了断裂机理 .随着蒙脱土含量的增加 ,冲击断裂形式逐渐从脆性断裂变成韧性断裂     

聚丙烯酰胺/蒙脱土纳米复合物-聚乙烯醇共混膜的制备及其渗透汽化性能

用原位聚合法制备聚丙烯酰胺/蒙脱土(PAM/MMT)纳米复合材料, 通过透射电镜研究了蒙脱土在聚丙烯酰胺基体中的形貌和分布. 结果表明, 蒙脱土以片层结构分布在聚合物基体中. 用超声波分散聚乙烯醇和聚丙烯酰胺-蒙脱土共混铸膜液制得共混膜, 用红外吸收光谱和扫描电镜研究了两者的相互作用和形貌. 考察了共混膜在异丙醇-水混合溶液中的溶胀吸附性能及共混比和蒙脱土含量对膜分离性能的影响, 结果显示, 聚乙烯醇膜中添加适量的蒙脱土纳米粒子可以大大改善膜的分离选择性.     

聚N-甲基苯胺/蒙脱土纳米复合材料的合成及其协同电流变效应

用插层聚合法制备了聚N 甲基苯胺 蒙脱土纳米复合材料微粒 ,通过IR、XRD及TEM对其结构进行了表征 .观察发现聚N 甲基苯胺插入蒙脱土层间后 ,蒙脱土片层间距由 0 96nm扩大至 1 34nm .将其分散在甲基硅油中 (2 0wt% )配制成无水电流变液 ,该复合材料表现出显著的协同效应 ,具有较好的电流变行为 .实验表明在电场作用下聚N 甲基苯胺 蒙脱土纳米复合材料的电流变效应比聚苯胺、蒙脱土都有显著提高 ,在 3kV mm(DC ,74 5s- 1 )时 ,剪切强度达 6 0kPa ;同时抗沉降性极好 ,静置 6 0天沉淀率小于 3% .介电性能测试表明聚N 甲基苯胺 蒙脱土纳米颗粒的介电常数和介电损耗较蒙脱土和聚N 甲基苯胺明显提高 ,电导率也达到了最佳范围 .     

熔体插层制备尼龙6/蒙脱土纳米复合材料的性能表征

通过熔体插层成功地制备了尼龙６／蒙脱土纳米复合材料，测试了力学性能、耐热性能和耐溶剂性．通过ＴＥＭ、ＷＡＸＤ、ＤＳＣ等手段，研究了结构与结晶行为，并与插层聚合的尼龙６／蒙脱土纳米复合材料进行了对比．实验表明通过熔体插层可使尼龙６基体插层于蒙脱土中，所得到的复合物的性能较尼龙６有很大提高，且与插层聚合的尼龙６／蒙脱土纳米复合材料的性能相当．     

聚氨酯弹性体/蒙脱土纳米复合材料的合成、结构与性能

采用插层聚合法合成了综合力学性能优异的聚氨酯 蒙脱土纳米复合材料 .X 射线衍射结果表明 ,蒙脱土以平均层间距不小于 4 5nm的宽分布分散在聚氨酯基体中 .加入 7 5wt%左右的蒙脱土 ,复合材料的拉伸强度高于纯PU基体的 2倍 ,断裂伸长率则高于纯PU基体的 4倍以上 .TGA分析表明 ,聚氨酯 蒙脱土纳米复合材料的热稳定性略有提高     

聚苯乙烯/蒙脱土熔融插层复合的研究

用熔融法制备了聚苯乙烯／蒙脱土插层复合材料，用Ｘ 射线衍射、ＤＳＣ等手段研究了复合材料的结构与性能．聚苯乙烯熔体不能插层于钠基蒙脱土中，但能插层于经有机化合物处理过的蒙脱土中．     

聚萘并噁嗪/蒙脱土纳米复合材料的制备与表征

用原位插层反应法地制备了聚萘并嗪 蒙脱土纳米复合材料 .采用X ray衍射 (XRD)及透射电镜(TEM)研究复合材料中蒙脱土硅酸盐片层间距 ,发现硅酸盐片层间距由 1 2 6nm扩增至 5 88nm以上 .同时研究了该复合材料的耐热性 ,并探讨了复合材料的结晶行为     

硅烷化聚氨酯复合催化剂的研究

以聚丙二醇、TDI、N-正丁基-γ-氨丙基三甲氧基硅烷和蒙脱土为主要原料,采用原位聚合方法研究了蒙脱土和有机铋化合物对环境友好和储存稳定的硅烷化聚氨酯催化作用.通过滴定法测试了反应体系中异氰酸根(NCO)含量的变化,发现蒙脱土可以催化NCO与OH的反应,且与有机铋化合物具有协同效应,利用在线红外分析仪证实了蒙脱土的催化...     

Investigation of novel composites to be used as backfill materials in radioactive waste disposal facilities

Journal of Radioanalytical and Nuclear Chemistry - The current work aims at the preparation and characterization of novel composite materials of acrylic acid/charcoal/montmorillonite (MMT) (PAACM...     

In situ Polymerization Technique for Obtaining Composite Materials Based on Polyethylene,Multi-walled Carbon Nanotubes and Cobalt Nanoparticles

Specific features of formation of composite materials based on polyethylene, multi-walled carbon nanotubes, and cobalt nanoparticles (MWCNT–PE and Co/MWCNT–PE) by in situ polymerization were revealed. The in situ polymerization technique is based on ethylene polymerization on a highly dispersed Ti-containing catalyst supported on the surface of MWCNT and Со/MWCNT. This method ensures uniform distribution of MWCNT and Co/MWCNT in the polyethylene matrix. The effect of MWCNT and Со/MWCNT on the final properties of the composite materials was determined. Introduction of MWCNT into the polyethylene matrix increases the specific electrical conductivity of the material. Such composite materials can be used for preparing concentrates with preset composition for the subsequent preparation of antistatic coatings. Introduction of the Со/MWCNT filler into the polyethylene matrix makes the material paramagnetic owing to Co nanoparticles and allows its use for preparing coatings that efficiently protect from electromagnetic radiation.     

Synthesis and Characterization of Montmorillonite-Graft-Acrylic Acid Superabsorbent by Using Glow-Discharge Electrolysis Plasma

Crosslinking graft polymerization of poly acrylic/montmorillonite superabsorbent composite in aqueous solution was prepared by using glow-discharge electrolysis plasma, in which acrylic acid and acid-activated montmorillonite were used as starting materials, N,N-methylenebisacrylamide as a crosslinking agent. To optimize the synthetic conditions, seven important parameters of the graft-polymerization were examined in detail, such as the discharge voltage, discharge time, the neutralization of acrylic acid, post polymerization temperature, amounts of crosslinking agent, montmorillonite and acrylic acid used in this study. The structure, thermal stability and morphology of product were characterized by Fourier transform infrared spectroscopy, thermogravimetric analysis, scanning electron microscopy, respectively. The absorbency of poly acrylic/montmorillonite superabsorbent was examined to yield the following results: 1,834 g/g for distilled water, 116 g/g for 0.05 mol/L and 75 g/g for 0.15 mol/L sodium chloride solution. Such excellent character could be important to use in many fields, for example, in agricultural and horticultural applications.     

Preparation and characterization of polyaniline/MMT conductive composites

Polyaniline/montmorillonite (PAn/MMT) composite material has been prepared through chemical‐oxidative polymerization by using NH₄S₂O₈ as the oxidant, and it was found that both the composites have inorganic and organic material characteristics and many outstanding performance through the copolymerization coupling of MMT and polyaniline. Infrared spectroscopy (FT‐IR), thermogravimetric analysis (TGA), X‐ray diffraction (XRD), and transmission electron microscopy (TEM) are used to characterize the composition and structures of composite materials, as well as test the conductivity of composite materials through a four‐probe technique. The preparation conditions of PAn/MMT conducting composites are optimized. The optimal conditions have been identified for the reaction time, amount of oxidizer, concentration of HCl, and the amount of MMT. Besides, the results show that when the reaction lasts for 8 hr in the ice bath, the amount of MMT is 0.4 g/5 ml An, the mole ratio of oxidant to aniline is 1, and the concentration of hydrochloric acid is 2 M, the composite had the largest conductivity up to 11.5 S/cm. In addition, we also did an elemental analysis of the composite mechanism of PAn/MMT composites. Copyright © 2008 John Wiley & Sons, Ltd.     

The influence of interlayer cations on the photo‐oxidative degradation of polyethylene/montmorillonite composites

The photo‐oxidative degradation of polyethylene/montmorillonite (PE/MMT) nanocomposite and microcomposite has been investigated. It has been found that the rate of photo‐oxidative degradation of PE/MMT nanocomposite and PE/Mⁿ⁺MMT (where Mⁿ⁺ stands for multivalent transition metal cation) microcomposites is much faster than that of pure PE. For the PE/MMT nanocomposite, the acceleration of photo‐oxidative degradation is due to the influence of MMT and ammonium ion, in which the influence of ammonium is primary. The decomposition of ammonium ion may create acidic sites on layered silicates; meanwhile, the complex crystallographic structure and habit of clay minerals could also result in some active sites. The reversible photo‐redox reaction of transition metal cations has a catalytic effect in the degradation of the polymer matrix. All these catalytic active sites can accept single electrons from donor molecules of polymer matrix and induce the formation of free radical upon UV irradiation. The generation of free radical leads to the oxidization and break of molecular chain. Thus, the materials suffer degradation and their mechanical strength decreases. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 3006–3012, 2004     

Reversible Addition‐Fragmentation Transfer Polymerization in the Presence of MMT Immobilized Amphoteric RAFT Agent

Summary: A novel reversible addition‐fragmentation transfer (RAFT) agent, 10‐carboxylic acid‐10‐dithiobenzoate‐decyltrimethylammonium bromide (CDDA), was synthesized and intercalated into montmorillonite (MMT). Successively, the CDDA‐intercalated MMT was used as RAFT agent in the in situ RAFT polymerization for preparation of the polystyrene/MMT nanocomposites. After separation of MMT, the polymers obtained have predictable molecular weight and narrow polydispersity. XRD spectra and TEM images of the nanocomposites demonstrated exfoliated structure. Thermal stability of the composites has been noticeably improved.

     

The Effect of Filler Type on the Mechanical Properties of Composite Materials Based on Ultra-High-Molecular-Weight Polyethylene

The effect of the filler type (graphite nanoplates, organomodified montmorillonite, molybdenum disulphide, or shungite) on the deformation and strength properties of composite materials based on UHMWPE synthesized by in situ polymerization with a filler content of up to 0.06 vol fraction was studied. The significant effect of the filler type on the dependence of the tensile strength and the tensile elongation of the studied composites on the filler content was established. A significant difference between the tensile stress–strain curves for composites with different fillers was observed.     

石墨相氮化碳/蒙脱石复合材料的制备及其可见光催化性能

为提高石墨相氮化碳(g-C₃N₄)对可见光的利用率及光催化效率,采用热聚合与直接负载等方法,将g-C₃N₄负载于蒙脱石表面,制备了g-C₃N₄/蒙脱石复合光催化材料,其结构经SEM, FT-IR及XRD表征。以罗丹明B(RhB)为目标污染物,研究了不同负载量g-C₃N₄/蒙脱石复合光催化剂的可见光催化性能。并分别以对苯醌、碘化钾和异丙醇为自由基捕获剂,研究了复合材料的光催化机理。结果表明：当g-C₃N₄的质量分数为83%(CN/M-83%)时,RhB经可见光照射1 h后,降解率达到99.2%。光催化速率常数为纯g-C₃N₄光催化速率常数的3.2倍。     

Preparation and Characterization of PMMA/MMT Organic-Inorganic Hybrid Materials via RAFT Polymerization

In this article, the poly(methyl methacrylate)/montmorillonite (PMMA/MMT) organic-inorganic hybrid materials were prepared by conventional free radical polymerization and reversible addition-fragmentation chain transfer (RAFT) polymerization, respectively. The kinetics comparison of these two polymerizations was studied. The PMMA/MMT hybrid materials were characterized by gel permeation chromatography (GPC), differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA). According to these results, we knew that the polymerization behavior of MMA showed controlled/living radical polymerization (CLRP) characteristics under the control of RAFT agent. The incorporation of RAFT agent and MMT nanoparticles improved the thermal properties of polymers, and the thermal stability of polymers increased with increasing content of MMT nanoparticles. The structures and morphologies of PMMA/MMT hybrid materials were characterized by FT-IR, XRD and TEM. These results showed that the MMA monomer can be initiated and propagated in the clay layers of MMT via the control of RAFT agent, and then the exfoliated structure was obtained for the hybrid materials.