Flow-induced oscillation of two circular cylinders in tandem arrangement at low Re

Results are presented for flow-induced vibrations of a pair of equal-sized circular cylinders of low nondimensional mass (m^*=10) in a tandem arrangement. The cylinders are free to oscillate both in streamwise and transverse directions. The Reynolds number, based on the free-stream speed and the diameter of the cylinders, D is 100 and the centre-to-centre distance between the cylinders is 5.5D. The computations are carried out for reduced velocities in the range 2≤U^*≤15. The structural damping is set to zero for enabling maximum amplitudes of oscillation. A stabilized finite element method is utilized to carry out the computations in two dimensions. Even though the response of the upstream cylinder is found to be qualitatively similar to that of an isolated cylinder, the presence of a downstream cylinder is found to have significant effect on the behaviour of the upstream cylinder. The downstream cylinder undergoes very large amplitude of oscillations in both transverse and streamwise directions. The maximum amplitude of transverse response of the downstream cylinder is quite similar to that of a single cylinder at higher Re beyond the laminar regime. Lock-in and hysteresis are observed for both upstream and downstream cylinders. The downstream cylinder undergoes large amplitude oscillations even beyond the lock-in state. The phase between transverse oscillations and lift force suffers a 180 jump for both the cylinders almost in the middle of the synchronization regime. The phase between the transverse response of the two cylinders is also studied. Complex flow patterns are observed in the wake of the freely vibrating cylinders. Based on the phase difference and the flow patterns, the entire flow range is divided into five sub-regions.     

Free-stream turbulence effects on the instantaneous pressure and forces on cylinders of rectangular cross section

Simultaneous measurements of instantaneous pressure distributions on rectangular cylinders of length to height ratio(B/D) of 1.0, 2.5 and 3.0 in smooth nonturbulent and homogeneous turbulent flows were made and the data were analyzed by phase averaging and spectral analysis in addition to more conventional methods. The turbulence in the inflow stream is nearly homogeneous and isotropic with the intensity and the scale of 5% and 1.2-1.5 times the cylinder height, respectively. The main effects of the turbulence in the inflow free stream of this scale and intensity are to laterally move the separated shear flow off the upstream corners and cause intermittent reattachment on the side surfaces of cylinders of B/D of 2.5 and larger. For the cylinder with smaller B/D, the flow does not reattach with or without turbulence in the free stream, and the instantaneous surface pressure distributions fluctuate quite periodically at a frequency corresponding to the Strouhal frequency of the vortex shedding. The effects of the free-stream turbulence appear in the increased fluctuation on the front surface as buffeting due to the impinging turbulence. When the separated shear layers reattach due to the influence of the free-stream turbulence, the reattachment point moves intermittently, the pressure distributions downstream of the reattachment fluctuate periodically, and a mild peak is formed in the spectra at a frequency much larger than the Strouhal frequency.     

Simulation of cross-flow-induced vibration of cylinder arrays by surface vorticity method

The surface vorticity method (SVM), which is a fast and practical grid-free two-dimensional (2-D) method, and a fluid–structure interaction model incorporating the effects of cylinder motions and displacements is used to simulate the vortex-induced vibration of cylinder arrays at sub-critical Reynolds number Re=2.67×10⁴. The SVM is found to be most suitable for simulating a 2-D cylinder row with large-amplitude vibrations where the vorticity field and the fluid forces of the cylinder row change drastically, and the effect of the stream on the transverse direction vibration is very significant. The fluidelastic instability of a flexible cylinder row at small pitch ratio is also investigated, and the critical reduced velocity of the cylinder row at a reduced damping parameter S_G=1.29 is calculated, which is in good agreement with experimental and analytical results of the unsteady model. Vortex-induced vibration of a staggered cylinder array is simulated using different structural parameters. When the cylinders are relatively more flexible, the flow pattern changes dramatically and the fluid–structure interaction has a dominant impact on the flow field. Compared with grid-based methods, the grid-free SVM is a fast and practical method for the simulation of the FIV of cylinder arrays due to vortex shedding at sub-critical Reynolds numbers.     

Simulation of turbulent flows around a circular cylinder using nonlinear eddy-viscosity modelling: steady and oscillatory ambient flows

Steady incident flow past a circular cylinder for sub- to supercritical Reynolds number has been simulated as an unsteady Reynolds-averaged Navier–Stokes (RANS) equation problem using nonlinear eddy-viscosity modelling assuming two-dimensional flow. The model of Craft et al. (Int. J. Heat Fluid Flow 17 (1996) 108), with adjustment of the coefficients of the ‘cubic’ terms, predicts the drag crisis at a Reynolds number of about 2×10⁵ due to the onset of turbulence upstream of separation and associated changes in Strouhal number and separation positions. Slightly above this value, at critical Reynolds numbers, drag is overestimated because attached separation bubbles are not simulated. These do not occur at supercritical Reynolds numbers and drag coefficient, Strouhal number and separation positions are in approximate agreement with experimental measurements (which show considerable scatter). Fluctuating lift predictions are similar to sectional values measured experimentally for subcritical Reynolds numbers but corresponding measurements have not been made at supercritical Reynolds numbers. For oscillatory ambient flow, in-line forces, as defined by drag and inertia coefficients, have been compared with the experimental values of Sarpkaya (J. Fluid Mech. 165 (1986) 61) for values of the frequency parameter, β=D²/νT, equal to 1035 and 11240 and Keulegan–Carpenter numbers, KC=U₀T/D, between 0.2 and 15 (D is cylinder diameter, ν is kinematic viscosity, T is oscillation period, and U₀ is the amplitude of oscillating velocity). Variations with KC are qualitatively reproduced and magnitudes show best agreement when there is separation with a large-scale wake, for which the turbulence model is intended. Lift coefficients, frequency and transverse vortex shedding patterns for β=1035 are consistent with available experimental information for β≈250−500. For β=11240, it is predicted that separation is delayed due to more prominent turbulence effects, reducing drag and lift coefficients and causing the wake to be more in line with the flow direction than transverse to it. While these oscillatory flows are highly complex, attached separation bubbles are unlikely and the flows probably two dimensional.     

Transonic crossflow of condensing wet steam past a cylinder

The shadow and interferometric methods and the laser probe method are used to investigate crossflow past a cylinder on the free-stream Mach number interval M _a =0.5–1.2 for subcritical Reynolds numbers Re _d and various initial steam states. Detailed pressure distributions are obtained and the pressure fluctuations on the cylinder surface are measured. The dependence of the Strouhal number on the velocity and thermodynamic parameters of the flow are determined. In single-phase steam flow past a cylinder the greatest fluctuations occur in the separation zone in regimes corresponding to transonic drag crisis. It is shown that spontaneous condensation in the turbulent wake and local supersonic zones may cause an increase in the periodic pressure fluctuations in the separation zone, the maximum increase in the fluctuations being noted when the critical pressure ratio is reached at the rear of the cylinder. The initial wetness of the steam has the greatest effect on the periodic separation characteristics at subsonic flow velocities, and in the case of supersonic flow leads to a substantial increase in the level of the low-frequency pressure fluctuations at the front of the cylinder.(deceased)Moscow. Translated from Izvestiya Rossiiskoi Akademii Nauk, Mekhanika Zhidkosti i Gaza, No. 6, pp. 118–138, November–December, 1994.     

Experimental study of vortex-induced vibrations of a cylinder near a rigid plane boundary in steady flow

In this study, the vortex-induced vibrations of a cylinder near a rigid plane boundary in a steady flow are studied experimentally. The phenomenon of vortex-induced vibrations of the cylinder near the rigid plane boundary is reproduced in the flume. The vortex shedding frequency and mode are also measured by the methods of hot film velocimeter and hydrogen bubbles. A parametric study is carded out to investigate the influences of reduced velocity, gap-to-diameter ratio, stability parameter and mass ratio on the amplitude and frequency responses of the cylinder. Experimental results indicate： （1） the Strouhal number （St） is around 0.2 for the stationary cylinder near a plane boundary in the sub-criti- cal flow regime; （2） with increasing gap-to-diameter ratio （eo/D）, the amplitude ratio （A/D） gets larger but frequency ratio （f/fn） has a slight variation for the case of larger values of eo/D（eo/D 〉 0.66 in this study）; （3） there is a clear difference of amplitude and frequency responses of the cylin- derbetween the larger gap-to-diameter ratios （e0/D 〉 0.66） and the smaller ones （e0/D 〈 0.3）; （4） the vibration of the cylinder is easier to occur and the range of vibration in terms of Vr number becomes more extensive with decrease of the stability parameter, but the frequency response is affected slightly by the stability parameter; （5） with decreasing mass ratio, the width of the lock-in ranges in terms of Vr and the frequency ratio （f/fn） become larger.     

Simultaneous CFD evaluation of VIV suppression using smaller control cylinders

Two-degree-of-freedom vortex-induced vibrations (VIV) of a circular cylinder with and without two smaller control cylinders are investigated numerically by computational fluid dynamics (CFD) models coupling with a fluid–structure interaction (FSI) computational method. The numerical model is validated against experimental data of VIV of an isolated cylinder in uniform current. The study is aimed to investigate the effect of smaller control cylinders on VIV suppression. The trajectories of cylinder motion, amplitude response, and temporal evolution of vortex shedding and streamlines are obtained by conducting a series of simulations. And the effect of Reynolds number, located angle and rotational rate of small control cylinders are discussed in detail. It is found that placing small cylinders at 45° to the downstream vector can achieve a good suppression effect, but the effect is different at different Re. Rotating control cylinders with a reasonable rotation velocity can further enhance the VIV suppression by injecting enough momentum into the boundary layer of the main cylinder. The best effect is found at U_c=10, which has a 64.56% reduction in the transverse vibration response.     

Flow structure around perforated cylinders in shallow water

The experimental investigations were carried out in order to have detailed information on the flow structure around perforated cylinders using high-image density Particle Image Velocimetry technique in shallow water flow. The depth-averaged free-stream velocity was kept constant as U_∞=100 mm/s corresponding to the Reynolds number of Re=10 000 based on the perforated cylinder diameter. In order to analyze the effect of porosity, β on the flow structure, the porosities in the range of 0.1≤β≤0.8 with an increment of 0.1 were used and the results were compared with the bare cylinder case by means of velocity and vorticity contours, turbulent kinetic energy, Reynolds shear stress and streamline topologies. It was concluded that the porosity, β had a substantial effect on the control of large-scale vortical structures downstream of the cylinder in which the shear layers were elongated, fluctuations were significantly attenuated and formation of Karman Vortex Street was successfully prevented by the use of perforated cylinders.     

Cross-flow past a pair of nearly in-line cylinders with the upstream cylinder subjected to a transverse harmonic oscillation

An experimental investigation is presented for the cross-flow past a pair of staggered circular cylinders, with the upstream cylinder subject to forced harmonic oscillation transverse to the flow direction. Experiments were conducted in a water tunnel with Reynolds numbers, based on upstream velocity, U, and cylinder diameter, D, in the range 1440⩽Re⩽1680. The longitudinal separation between cylinder centres is L/D=2.0, with a transverse separation (for the mean position of the upstream cylinder) of T/D=0.17; the magnitude of the harmonic oscillation is 0.44D peak-to-peak and the nondimensional frequency range of the excitation is 0.05⩽f_eD/U⩽0.44. Flow visualization of the wake-formation region and hot-film measurements of the wake spectra are used to investigate the wake-formation process. An earlier study showed that stationary cylinders in this nearly in-line configuration straddle two very different flow regimes, the so-called shear-layer reattachment (SLR) and induced separation (IS) regimes. The present study, demonstrates that oscillation of the upstream cylinder causes considerable modification of the flow patterns around the cylinders. In particular, the wake experiences strong periodicities at the frequency of the oscillating cylinder; in addition to the usual fundamental lock-in, both sub- and superharmonic resonances are obtained. It is also observed that, although the flow exhibits regions of SLR and IS for excitation frequencies below the fundamental lock-in, for frequencies above the lock-in range the flow no longer resembles either of these flow regimes and vortices are formed in the gap between the cylinders.     

Passive Scalar Transport in a Turbulent Cylinder Wake in the Presence of a Downstream Cylinder

This work aims to investigate how the presence of a downstream cylinder affects the passive scalar transport in a cylinder wake. The wake was generated by two tandem brass circular cylinders of the same diameter (d). The cylinder centre-to-centre spacing L/d was 1.3, 2.5 and 4.0, respectively, covering the three typical flow regimes of this flow. The upstream cylinder was slightly heated. Measurements were conducted at x/d= 10 and Re (≡ dU _∞/ν, where U _∞ is the free-stream velocity and ν is the kinematic viscosity of fluid) = 7000. A three-wire probe consisting of an X-wire and a cold wire was used to measure the velocity and temperature fluctuations, while an X-wire provided a phase reference. The phase-averaged velocity vectors and vorticity display single vortex street behind the downstream cylinder, irrespective of the flow regimes. However, the detailed flow structure exhibits strong dependence on L/d in terms of the Strouhal number, the vortex strength and its downstream evolution. This naturally affects passive scalar transport. The coherent and incoherent heat flux vectors show significant variation for different L/d.     

Vortex shedding from two finite circular cylinders in a staggered configuration

Wind tunnel experiments were conducted to measure the vortex shedding frequencies for two circular cylinders of finite height arranged in a staggered configuration. The cylinders were mounted normal to a ground plane and were partially immersed in a flat-plate turbulent boundary layer. The Reynolds number based on the cylinder diameter was Re_D=2.4×10⁴, the cylinder aspect ratio was AR=9, the boundary layer thickness relative to the cylinder height was δ/H=0.4, the centre-to-centre pitch ratio was varied from P/D=1.125 to 5, and the incidence angle was incremented in small steps from α=0° to 90°. The Strouhal numbers were obtained behind the upstream and downstream cylinders using hot-wire anemometry. From the behaviour of the Strouhal number data obtained at the mid-height position, the staggered configuration could be broadly classified by the pitch ratio as closely spaced (P/D<1.5), moderately spaced (1.5?P/D?3), or widely spaced (P/D>3). The closely spaced staggered finite cylinders were characterized by the same Strouhal number measured behind both cylinders, an indication of single bluff-body behaviour. Moderately spaced staggered finite cylinders were characterized by two Strouhal numbers at most incidence angles. Widely spaced staggered cylinders were characterized by a single Strouhal number for both cylinders, indicative of synchronized vortex shedding from both cylinders at all incidence angles. For selected staggered configurations representative of closely spaced, moderately spaced, or widely spaced behaviour, Strouhal number measurements were also made along the vertical lengths of the cylinders, from the ground plane to the free end. The power spectra showed that for certain cylinder arrangements, because of the influences of the cylinder–wall junction and free-end flow fields, the Strouhal numbers and flow patterns change along the cylinder.     

Vortex-induced oscillations at low Reynolds numbers: Hysteresis and vortex-shedding modes

Results are presented for the numerical simulation of vortex-induced vibrations (VIVs) of a cylinder at low Reynolds numbers (Re). A stabilized space–time finite-element formulation is utilized to solve the incompressible flow equations in primitive variables. The cylinder, of low nondimensional mass (m^*=10), is free to vibrate in, both, the transverse and in-line directions. To investigate the effect of Re and reduced natural frequency, F_n, two sets of computations are carried out. In the first set of computations the Reynolds number is fixed (=100) and the reduced velocity (U^*=1/F_n) is varied. Hysteresis, in the response of the cylinder, is observed at the low- as well as high-end of the range of reduced velocity for synchronization/lock-in. In the second set of computations, the effect of Reynolds number (50Re500) is investigated for a fixed reduced velocity (U^*=4.92). The effect of the Reynolds number is found to be very significant for VIVs. While the vortex-shedding mode at low Re is 2S (two single vortices shed per cycle), at Re300 and larger, the P+S mode of vortex shedding (a single vortex and one pair of counter-rotating vortices are released in each cycle of shedding) is observed. This is the first time that the P+S mode has been observed for a cylinder undergoing free vibrations. This change of vortex-shedding mode is hysteretic in nature and results in a very large increase in the amplitude of in-line oscillations. Since the flow ceases to remain two-dimensional beyond Re200, it remains to be seen whether the P+S mode of shedding can actually be observed in reality for free vibrations.     

The turbulent wake of a circular cylinder rotating about the streamwise axis

This paper presents measurements in the turbulent wake of a circular cylinder rotating with its axis normal to the free-stream velocity; in other words, the axis of rotation was parallel to the streamwise direction. All three mean velocities and six Reynolds stresses were obtained at three positions downstream of the cylinder, with and without rotation of the free-stream. Most emphasis is given to the latter results because of the better flow quality. The ratio of the circumferential velocity of the cylinder to the free-stream velocity — the swirl number — had a maximum value of 0.6. Measurements for two combinations of the free-stream and angular velocities showed the velocity deficit in the wake to be a multi-valued function of the swirl number, implying that the rotation affected the separation of the cylinder's boundary layer in a complex manner. In the turbulent wake, the rotation did not significantly alter the magnitudes of the normal stresses, but caused large changes to the shape of the profiles of the axial and cross-stream normal stresses. Eventually, the primary (cross-stream) shear stress became almost entirely positive, but there was no corresponding change to the (cross-stream) gradient of the streamwise mean velocity. Despite these alterations to the turbulence, the rotationally-activated generation terms in the Reynolds transport equations never dominated the terms that are common to the wakes of rotating and non-rotating cylinders.This work was supported by the Australian Research Council. Most of the data acquisition software was written by Mr J. J. Smith.     

Wake-induced vibrations of an elastically mounted cylinder located downstream of a stationary larger cylinder at low Reynolds numbers

Two-dimensional numerical simulations of flow past two unequal-sized circular cylinders in tandem arrangement are performed at low Reynolds numbers (Re). The upstream larger cylinder is stationary, while the downstream cylinder has both one (transverse-only) and two (transverse and in-line) degrees of freedom (1-dof and 2-dof, respectively). The Re, based on the free stream velocity U_∞ and the downstream cylinder diameter d, varies between 50 and 200 with a wide range of reduced velocities U_r. The diameter of the upstream cylinder is twice that of the downstream cylinder, and the center-to-center spacing is 5.5d. In general, for the 1-dof case, the calculations show that the wake-induced vibrations (WIV) of the downstream cylinder are greatly amplified when compared to the case of a single cylinder or two equal-sized cylinders. The transverse amplitudes build up to a significantly higher level within and beyond the lock-in region, and the U_r associated with the peak amplitude shifts toward a higher value. The dominant wake pattern is 2S mode for Re=50 and 100, while with the increase of Re to 150 and 200, the P+S mode can be clearly observed at some lower U_r. For the 2-dof vibrations, the transverse response characteristics are similar to those presented in the corresponding 1-dof case. The in-line responses are generally much smaller, except for several significant vibrations resulting from in-line resonance. The obvious in-line vibration may induce a C (chaotic) vortex shedding mode for higher Re (Re=200). With regard to the 2-dof motion trajectories, besides the typical figure-eight pattern, several odd patterns such as figure-double eight and single-looped trajectories are also obtained due to the wake interference effect.     

Vortex dynamics of a cylinder wake in proximity to a wall

Large-eddy simulations (LES) are used to investigate the modifications of wake dynamics and turbulence characteristics behind a circular cylinder placed near a wall for varying gap-to-diameter (G/D) ratios (where G signifies the gap between the wall and the cylinder, and D the cylinder diameter). The three-dimensional (3-D), time-dependent, incompressible Navier–Stokes equations with a dynamic subgrid-scale model are solved using a symmetry-preserving finite-difference scheme of second-order spatial and temporal accuracy. The immersed boundary (IB) method is employed to impose the no-slip boundary condition on the cylinder surface. Flow visualizations along with turbulence statistics are presented to gain insight into the flow structures that are due to interaction between the shear layers and the approaching boundary layer. Apart from the vortex shedding mechanism, the paper illustrates the physics involving the shear layer transition, stretching, breakdown and turbulence generation, either qualitatively or quantitatively, in the presence of a wall for a Reynolds number of Re=1440 (based on D and the inlet free-stream velocity U_∞).     

Self-sustained oscillations between two tandem cylinders at Reynolds number 1,000

This study focuses on the self-sustained oscillatory flow characteristics between two tandem circular cylinders of equal diameter placed in a uniform inflow. The Reynolds number (Re _D ), based on the cylinder diameter, was around 1,000 and all experiments were performed in a recirculating water channel. The streamwise distance between two tandem cylinders ranged within 1.5 ≤ X _c/D ≤ 7.0. Here X _c denotes the center-to-center distance between two tandem cylinders. For all experiments studied herein, quantitative velocity measurements were performed using hot-film anemometer and the LDV system. The laser sheet technique was employed for qualitative flow visualization. The wavelet transform was applied to elucidate the temporal variation and phase difference between two spectral components of the velocity signals detected in the flow field. The remarkable finding was that when two tandem circular cylinders were spaced at a distance within 4.5 ≤ X _c/D ≤ 5.5, two symmetrical unstable shear layers with a certain wavelength were observed to impinge onto the downstream cylinder. The responding frequency (f _u ), measured between these two cylinders, was much higher than the natural shedding frequency behind a single isolated cylinder at the same Re _D . This responding frequency decreased as the distance X _c/D increased. Not until X _c/D ≥ 6.0, did it recover to the natural shedding frequency behind a single isolated cylinder. Between two tandem cylinders, the Strouhal numbers (St _c = f _u X _c/U_c) maintained a nearly constant value of 3, indicating the self-sustained oscillating flow characteristics with a wavelength X _c/3. Here U _c is the convection speed of the unstable shear layers between two tandem cylinders. At Re _D = 1,000, the self-sustained oscillating characteristics between two tandem circular cylinders were proven to exhibit a sustained flow pattern, not just a sporadic phenomenon.     

Vortex induced vibration and vortex shedding characteristics of two side-by-side circular cylinders of different diameters in close proximity in steady flow

This paper presents results of a numerical study of vortex-induced vibrations of two side-by-side circular cylinders of different diameters in steady incompressible flow. The two-dimensional Reynolds-averaged Navier–Stokes equations with a SST k–ω turbulence model are solved using the Petrov–Galerkin finite element method and the Arbitrary-Lagrangian–Eulerian scheme. The diameter ratio of the two cylinders is fixed at 0.1 and the mass ratio of both cylinders is 5.0. Both cylinders are constrained to oscillate in the transverse direction only. The Reynolds number based on the large cylinder diameter and free stream velocity is fixed at 5000. The effects of the reduced velocities of the cylinders on the vibration amplitude and vortex shedding regimes are investigated. It is found that for the range of parameters considered, collision between the two cylinders is dependent on the difference of the reduced velocities of the cylinders. Presence of the small cylinder in the proximity of the large one appears to have significant effects on the vortex shedding regime and vibration amplitude of the large cylinder.     

A SERIES IN 1/√Re TO REPRESENT THE STROUHAL–REYNOLDS NUMBER RELATIONSHIP OF THE CYLINDER WAKE

In this Brief Note, we show that shedding frequency data is well collapsed, over a large range of Re from 50 up to at least 140,000, by using a Strouhal number that depends upon an effective wake width, which includes not only the physical body diameter, but also a characteristic width of the separating shear layers. The use of this effective wake width also leads to a new formulation for the relationship between Strouhal number (S) versus Reynolds number (Re) for the cylinder wake, which may be expressed as an expansion in powers of (1/√Re): EquationTruncated two-term or three-term series have much less error-of-fit when compared with the traditional S–Re relationships commonly in use. A good test of any S–Re functional relationship is now made possible by comparison with Henderson's numerical data for two-dimensional laminar shedding, over a much larger range of Re (up to Re=1000) than is possible to obtain experimentally. It seems significant that even a two-term fit, given by S=0·2698 −1·0271/√Re has one order of magnitude less error than the traditional three-term fit. By using such √Re-formulae in both the laminar and 3-D wake turbulent regimes, we may accurately represent S–Re data over a large range of Re, although the validity of these representations at these higher Re needs further support. In summary, this Brief Note not only provides physical support for the use of such S–Re relationships as shown above, but also demonstrates that these formulations fit the data closer than traditional S–Re expressions.     

Vortex-shedding from single and tandem cylinders in the presence of applied sound

A single cylinder and two tandem cylinder configurations with longitudinal pitch ratios L/D=1.75 and 2.5 were rigidly mounted in an open circuit wind tunnel and a standing acoustic pressure wave was imposed so that the acoustic particle velocity was normal to both the cylinder axis and the mean flow velocity. The effect of sound on the vortex-shedding was investigated for various amplitudes by means of pressure taps on the cylinders and wake hot-wire probes. These tests show that applied sound can entrain and shift the natural vortex-shedding frequency to the frequency of excitation and produce nonlinearities in the wake. The lock-in envelope for the tandem cylinders is considerably larger than for the single cylinder. The lock-in range for the smaller tandem cylinder spacing was broader still than either the single cylinder, or the L/D=2.5 tandem cylinder case. The pressure and hot-wire measurements show for the single cylinder, and tandem cylinder configuration with pitch ratio L/D=2.5, that there was a phase jump near the coincidence of the vortex-shedding frequency and the excitation frequency, while there was no jump for the pitch ratio of 1.75. As well, the applied sound field was also noted to induce vortex-shedding in the gap for the L/D=2.5 case, while no vortex-shedding was noted for the smaller pitch ratio.     

Two-dimensionality of a cantilevered-cylinder wake in the presence of an oscillating upstream cylinder

The effect of a longitudinally oscillating cylinder on the two-dimensionality of flow around a downstream cylinder is studied based on a two-point correlation measured using two hot-wires. The oscillation amplitude is A/d=0.472 and the oscillation frequency f_e/f_s=0.0372 and 0.186, where d is the cylinder diameter and f_s the frequency of natural vortex shedding from an isolated stationary cylinder. Three centre-to-centre spacing (L) ratios of the two cylinders were examined, i.e., L/d=1.8, 2.5 and 4.8, representing three typical flow regimes. The experiment was conducted at a Reynolds number (Re) of 5920, based on d and the free-stream velocity. It is found that the spanwise correlation of the flow depends on not only the oscillation but also the flow regimes. At L/d=1.8, the correlation is strongest among the three regimes, but worst in the co-shedding regime (L/d=4.8). The upstream cylinder oscillation improves the spanwise correlation of the flow in the gap of the cylinders, irrespective of regimes, especially for L/d=1.8 and 2.5, but impairs that behind the cylinders for L/d=1.8 and 2.5 due to a change in the flow regime. A theoretical analysis based on the boundary vorticity theory indicates that the oscillation increases the vorticity flux, in particular, in the spanwise direction between the cylinders, resulting in a significantly improved spanwise correlation, though this increase is negligibly small behind the downstream cylinder.