模板法制备CdSe纳米材料及其光电性能

采用电化学沉积法,在阳极氧化铝（AAO）模板中成功制备出CdSe纳米管和纳米线。利用扫描电子显微镜（SEM）、透射电子显微镜（TEM）、X射线衍射分析（XRD）和能量色散X射线光谱仪（EDS）对材料的形貌、结构和元素组成进行了表征。借助紫外-可见吸收光谱等对材料光催化活性进行了研究。结果表明：通过控制沉积电量可成功制备CdSe纳米管和纳米线;CdSe纳米材料为立方晶型与六方晶型的混合,经350℃退火处理后,CdSe纳米材料中由立方晶型向六方晶型转变,光照开路电位差值明显增强,在0 V（vs SCE）电位下的光照电流密度也有所提高,光电转换性能增强;CdSe纳米线的吸收边在710 nm左右,禁带宽度约为1.85 eV,CdSe纳米管相对于CdSe纳米线具有更高的光电转换性能和光催化活性,经7 h光照后,罗丹明B降解效率高达53.93%,另外,本文还讨论了CdSe纳米材料在AAO模板孔壁的生长机理。     

模板法制备CdSe纳米材料及其光电性能（英文）

采用电化学沉积法,在阳极氧化铝(AAO)模板中成功制备出CdSe纳米管和纳米线。利用扫描电子显微镜(SEM)、透射电子显微镜(TEM)、X射线衍射分析(XRD)和能量色散X射线光谱仪(EDS)对材料的形貌、结构和元素组成进行了表征。借助紫外-可见吸收光谱等对材料光催化活性进行了研究。结果表明:通过控制沉积电量可成功制备CdSe纳米管和纳米线;CdSe纳米材料为立方晶型与六方晶型的混合,经350℃退火处理后,CdSe纳米材料中由立方晶型向六方晶型转变,光照开路电位差值明显增强,在0 V(vs SCE)电位下的光照电流密度也有所提高,光电转换性能增强;CdSe纳米线的吸收边在710 nm左右,禁带宽度约为1.85 eV,CdSe纳米管相对于CdSe纳米线具有更高的光电转换性能和光催化活性,经7 h光照后,罗丹明B降解效率高达53.93%。另外,本文还讨论了CdSe纳米材料在AAO模板孔壁的生长机理。     

一维铜(核)-镍(壳)纳米结构的制备及其表面增强拉曼光谱

采用多孔阳极氧化铝模板(AAO)结合直流电化学沉积法, 通过一种新的两步法合成一维铜(核)-镍(壳)纳米结构. 首先制备铜纳米线, 然后对AAO进行扩孔, 利用铜纳米线和AAO孔壁之间的间隙,沉积镍纳米线/纳米管. 通过X射线衍射仪(XRD)、扫描电子显微镜(SEM)和透射电子显微镜(TEM)对其结构和形貌进行表征分析, 所得结果验证了这种方法的可行性. 以腺嘌呤为探针分子研究此种纳米结构的表面增强拉曼散射(SERS)效应, 结果表明, 这种一维纳米材料是一种潜在的SERS活性基底, 拓宽了过渡金属在SERS中的应用.     

CdSe纳米线阵列的制备及其表征(英)

通过在含有SeSO₃^2-和Cd²⁺的室温水溶液中，用模板-电沉积法在纳米孔阵列阳极氧化铝膜(AAM)模板中制备了高有序性的CdSe纳米线阵列，并对其形貌、结构和组分进行了表征。扫描电子显微镜(SEM)和透射电子显微镜(TEM)结果表明，纳米线阵列中的CdSe纳米线具有相同的长度和直径，分别对应于使用的AAM模板的厚度和孔径；X-射线衍射(XRD)和X-射线能谱(EDAX)结果表明，CdSe纳米线中Cd和Se的化学组成非常接近于1∶1，其结构为立方CdSe。另外，对模板-电沉积法制备CdSe纳米线的机理进行了讨论。     

ZnO-聚苯胺同轴纳米线及其列阵的制备和表征

以阳极氧化铝膜 (AAO)作模板 ,制备聚苯胺 (PANI)纳米管和PANI纳米管列阵 ;同时利用溶胶_凝胶法制备ZnO_PANI同轴纳米线和同轴纳米线列阵 .PANI纳米管和ZnO_PANI同轴纳米线的形貌通过透射电子显微镜表征 .PANI纳米管的外径约 3 0nm ,内径约 1 0nm ;ZnO_PANI同轴纳米线直径约 60nm .实验发现 ,较之ZnO纳米线 ,同轴AAO模板中纳米线列阵的可见光发射谱带兰移 ,强度显著增强 ,这可能和PANI链上的NH基团与表面Zn2 +离子之间的相互作用有关 ,以及由于ZnO纳米微粒在PANI上富集、PANI的光生载流子部分转移给ZnO微粒所致 .实验还发现分散在NaOH溶液中的同轴纳米线 ,其可见光发射谱带比AAO模板中同轴纳米线的谱带兰移更甚     

低频交流电沉积金纳米线阵列的AFM研究

迄今,人们已采用许多方法制备纳米材料,如刻蚀技术、化学法和模板法等［1]．其中,引起科学界广泛兴趣的模板法,在合成有序纳米材料上占有极其重要的地位．常用的模板有两种,一种是有序孔洞阳极氧化铝（Anodic Aluminum Oxide,AAO）模板[2],另一种是含有孔洞无序分布的高分子模板．AAO模板具有耐高温,绝缘性好,孔洞分布均匀有序,而且大小可控等特点［3]．可以利用 AAO模板来制备各种纳米纤维和纳米管,如导电聚合物［4]、金属［5]、半导体［6]、碳［7]和其它一些材料．由于纳米材料的应用具有广阔的前景,如光催化、电化学、酶固定等方面,因而不同材料纳米线的制备备受关     

模板法制备枝状Pt纳米线

一维纳米材料的制备是近年来纳米材料的研究热点. 利用具有纳米尺度的孔洞阵列模板沉积各种材料构筑纳米线的方法具有制备简便和成本较低等优点[1,2]. 常用的模板有多孔阳极氧化铝(AAO)、多孔硅和聚合物等, 其中AAO模板具有耐高温, 绝缘性好, 孔洞分布均匀, 孔径、孔深大小可控等特点, 是模板法研究的热点. 通过模板法电化学沉积制备各种金属纳米线已有很多报道[3～8], 本研究小组也曾报道了模板法电化学沉积Au等纳米线的制备及性质[9～12], 但用该方法制备的金属纳米线都为单一的线状结构. 组成当代大规模集成电路的基本器件一般具有3个或3个以上的电极. 单一的线状结构纳米线, 不能满足纳米电子学对纳米材料和纳米器件性能研究的需要. 在纳米器件的特性研究和探索中, 枝状或Y形纳米结的制备有重要的意义, 它是纳米器件从理论到实用化的必备条件. Sui等[13]用模板法成功制备了枝状碳纳米管, 但用AAO模板制备枝状金属纳米线的研究至今还未见报道. 本文通过控制铝片的阳极氧化条件, 先制备出具有分枝状孔洞结构的AAO模板, 再用电化学法沉积金属Pt, 实现了枝状Pt纳米线的可控生长. 这对其它金属枝状纳米线的制备以及进一步掺杂、构筑纳米原型器件等具有显著的实用价值.     

大面积Bi单晶纳米线阵列的制备

在有序的氧化铝模板(AAO)的孔洞中, 采用电化学沉积工艺成功地制备了准金属Bi纳米线有序阵列. 使用X射线衍射仪(XRD)、场发射扫描电子显微镜(FE-SEM)、透射电子显微镜(TEM)及高分辨电子显微镜(HRTEM)对样品的结构和形貌进行了表征. XRD结果表明, 所制备的铋样品为六方相, 且沿[110]方向有很好的生长取向; FE-SEM图片清晰地说明铋纳米线阵列是大面积、填充率高和高度有序的; TEM的结果显示纳米线直径均匀、表面光滑且长径比大; HRTEM图片中清晰的晶格条纹和选区电子衍射(SAED)结果表明纳米线是单晶.     

大长径比有序多孔阳极氧化铝模板的制备及用于镍纳米线阵列

报道一种恒电流二次氧化制备大长径比(>1000)阳极氧化铝(AAO)模板的方法,研究氧化时间和氧化电流密度分别对制备的AAO模板的表面形貌、孔径大小、厚度等的影响.结果表明,AAO模板的表面形貌及厚度n受m氧、厚化度电约流为密2度00及μ氧m、化长时径间比的为影10响0;-当13氧00化的电高流质密量度A为AO8模m板A·.c采m用-2电时化,氧学化沉1积8方h能法在制制备备出的孔A径A为O模15板0-的20孔0中成功制备了Ni纳米线阵列,分别用扫描电镜(SEM)、高分辨透射电镜(HRTEM)、X射线衍射(XRD)和X射线能量散射光谱(EDS)对其进行了表征;结果显示,制备的Ni纳米线排列整齐有序,每根Ni纳米线直径几乎相同,约150nm,长度约为180-200μm,长径比为1200-1300,与AAO模板的参数一致.研究了Ni纳米线阵列的长径比对其磁性能的影响,发现大长径比的Ni纳米线阵列具有明显的磁各向异性,而长径比约为200的Ni纳米线阵列未表现出明显的磁各向异性.本文结果表明,恒电流二次氧化方法能制备大长径比的AAO模板,并能用于制备大长径比的一维纳米材料阵列,可望在制备具有特殊光学、磁学等性能材料方面得到应用.     

钴纳米线的模板制备与磁性

利用二次阳极氧化法制备了多孔阳极氧化铝模板. 用直流电化学沉积方法成功地在模板孔道内制备了钴纳米线. 采用扫描电子显微镜(SEM)、X射线衍射仪(XRD)和振动样品磁强计(VSM)对样品的形貌、晶体结构和磁性进行了研究. 结果表明， 模板的孔径均匀, 孔道平直. 钴纳米线为多晶的六方密堆积结构. 钴纳米线具有明显的磁各向异性, 这主要起源于纳米线的形状各向异性.     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Selective syntheses of 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones via temperature-dependent Rh(II)-carbenoid-mediated 2H-azirine-ring expansion

The Rh(II)-catalyzed reaction of 2-carbonyl-substituted 2H-azirines with ethyl 2-cyano-2-diazoacetate or 2-diazo-3,3,3-trifluoropropionate provides an easy access to 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones. These compounds can be selectively prepared from the same starting material using temperature as the only varied parameter. The 2-azabuta-1,3-diene intermediate, a common precursor for both heterocyclic products, isomerizes into 2H-1,3-oxazine under kinetic control, while 1H-pyrrol-3(2H)-one is the sole product of the reaction at elevated temperatures. According to DFT-calculations a one-atom oxazine ring contraction involving ring-opening to a 2-azabuta-1,3-diene intermediate, followed by a 1,5- and 1,2-prototropic shift leads to the consecutive formation of imidoylketene and azomethine ylide, which then further undergo cyclization to the pyrrole derivative.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.