Development and validation of a capillary electrophoresis method with capacitively coupled contactless conductivity detection (CE-C(4) D) for the analysis of amikacin and its related substances

Amikacin is a semisynthetic aminoglycoside antibiotic derived from kanamycin A that lacks a strong UV absorbing chromophore or fluorophore. Due to the physicochemical properties of amikacin and its related substances, CE in combination with capacitively coupled contactless conductivity detection (CE-C(4) D) was chosen. The optimized separation method uses a BGE composed of 20 mM MES adjusted to pH 6.6 by l-histidine and 0.3 mM CTAB that was added as flow modifier in a concentration below the CMC. Ammonium acetate 20 mg.L(-1) was used as internal standard. 30 kV was applied in reverse polarity on a fused silica capillary (73/48 cm; 75 μm id). The optimized separation was obtained in less than 6 min with good linearity (R(2) = 0.9996) for amikacin base. It shows a good precision expressed as RSD on relative peak areas equal to 0.1 and 0.7% for intraday and interday, respectively. The LOD and LOQ are 0.5 mg.L(-1) and 1.7 mg.L(-1) , respectively.     

Measurement of tobramycin by reversed-phase high-performance liquid chromatography with mass spectrometry detection

Analysis of tobramycin faces challenges owing to its significant basicity, hydrophilicity and lack of a UV absorbing chromophore. Chromatographic methods, coupled with derivatization to introduce chromophores for tobramycin analysis, were extensively studied. A direct reversed-phase HPLC method for tobramycin analysis has not been reported. Here, we would like to report a simple LC/MS method for quantitative analysis of tobramycin in pharmaceutical formulations. Reversed-phase HPLC analysis of tobramycin was achieved using a pH stable C18 column with basic (pH 11) aqueous mobile phase (ammonium hydroxide buffer), while direct detection was carried out employing a single quadruple mass detector in negative mode via electrospray ionization. This unique separation-detection combination provided simple and specific determination of tobramycin. This method was found to be linear at a tobramycin concentration range of 0.2-0.8 mg/mL with a correlation coefficient value of 0.999. The quantitation limit and detection limit were calculated as 0.210 and 0.063 μg/mL, respectively, with 99.994% confidence. This method was successfully applied to measure tobramycin content in matrices containing tobramycin and other pharmaceutical formulation ingredients. Recoveries of 101.8, 97.8 and 106.7% were obtained for tobramycin spiked in the pharmaceutical formulation at concentrations of 1.68, 1.0 and 0.35 mg/mL, respectively. The relative standard deviations for six injections of spiked samples ranged from 0.2 to 3.2%, indicating good method repeatability.     

Applications of a copper microparticle-modified carbon fiber microdisk array electrode for the simultaneous determination of aminoglycoside antibiotics by capillary electrophoresis

A copper microparticle-modified carbon fiber microdisk array electrode was fabricated and employed in capillary electrophoresis for the simultaneous determination of the five aminoglycoside antibiotics (AGs) including netilmicin, tobramycin, lincomycin, kanamycin and amikacin. The array electrode exhibited high catalytic activity for AGs, good reproducibility and stability. Under the optimum separation conditions (separation voltage of 6.2 kV, electrophoretic medium of 125 mM NaOH), the five AGs above were baseline separated within 20 min. At a working electrode potential of 0.7 V (versus saturated calomel electrode), the calibration curves were linear over two orders of magnitude of concentration, and the detection limits (SIN=3) were below 2 microM except for lincomycin (6.7 microM). The developed method was successfully employed for the simultaneous determination of the five AGs studied in pharmaceutical injections. The feasibility of this method for the simultaneous determination of lincomycin, kanamycin and amikacin in urine sample was also demonstrated.     

Low-cost and versatile analytical tool with purpose-made capillary electrophoresis coupled to contactless conductivity detection: Application to antibiotics quality control in Vietnam

In this study, the development of our purpose-made capacitively coupled contactless conductivity detection (C⁴D) for CE is reported. These systems have been employed as a simple, versatile, and cost-effective analytical tool. CE-C⁴D devices, whose principle is based on the control of the ion movements under an electrical field, can be constructed even with a modest financial budget and limited infrastructure. A featured application was developed for quality control of antimicrobial drugs using CE-C⁴D, with most recent work on determination of aminoglycoside and glycopeptide antibiotics being communicated. For aminoglycosides, the development of CE-C⁴D methods was adapted to two categories. The first one includes drugs (liquid or powder form) for intravenous injection, containing either amikacin, streptomycin, kanamycin A, or kanamycin B. The second one covers drugs for eye drops (liquid or ointment form), containing either neomycin, tobramycin, or polymyxin. The CE-C⁴D method development was also made for determination of some popular glycopeptide antibiotics in Vietnam, including vancomycin and teicoplanin. The best detection limit achieved using the developed CE-C⁴D methods was 0.5 mg/L. Good agreement between results from CE-C⁴D and the confirmation method (HPLC- Photometric Diode Array ) was achieved, with their result deviations less than 8% and 13% for aminoglycoside and glycopeptide antibiotics, respectively.     

Quantitative determination and separation of analogues of aminoglycoside antibiotics by high-performance liquid chromatography

Commercial bulk products and pharmaceutical drug formulations of aminoglycoside antibiotics obtained by fermentation (kanamycin, gentamicin, sisomicin and tobramycin) or by synthesis (amikacin) were analysed with high-performance liquid chromatography on a C8 reversed-phase column. The method is based on a pre-column derivatization of the aminoglycosides with a 2,4,6-trinitrobenzenesulphonic acid reagent and UV detection (350 nm). The quantitative determination was carried out vs. an external standard; both peak heights and areas were used. A gentamicin mixture was separated into five or four components, depending on the column used. Amikacin was separated from its possible regioisomers and kanamycin A was easily separated from its minor components B and C.     

Novel and highly sensitive mixed-polymeric electrokinetic chromatography system for determination of contaminants and impurities of heparin samples

A mixed‐polymeric electrokinetic chromatography system has been developed for the simultaneous determination of a contaminant like oversulfated condroitin sulfate (OSCS) and impurities expressed as dermatan (Der) in heparin (Hep) samples. The EKC system consisted of 0.5% w/v polymeric β‐CD, 0.4% w/v tetronic^® 1107 and 400 mM tris‐phosphate buffer at pH 3.5. The optimized electrophoretic conditions included the use of an uncoated‐silica capillary of 50 cm of total length and 75 μm id, an applied voltage of ?7 kV, a temperature of 30°C and 200 nm UV‐detection. The highly sensitive method developed showed low values of LOD, 0.07% w/w (0.07 μg/mL) (OSCS) and 0.1% w/w (0.1 μg/mL) (Der), and values of LOQ 0.2% w/w (0.2 μg/mL) (OSCS) and 0.3% w/w (0.3 μg/mL) (Der) with a concentration level of Hep sample as low as 0.1 mg/mL. Additional parameters of validation such as specificity, linearity, accuracy, and robustness were evaluated according to international guidelines. Owing to its simplicity, high sensitivity, and reliability, the proposed method can be an advantageous alternative to the traditional methodologies for the analysis of Hep in raw material and specially in finished products because of the low amounts of Hep sample required.     

Capacitively coupled contactless conductivity detection as an alternative detection mode in CE for the analysis of kanamycin sulphate and its related substances

A method was developed to determine simultaneously kanamycin, its related substances and sulphate in kanamycin sulphate using capacitively coupled contactless conductivity detection. Kanamycin is an aminoglycoside antibiotic that lacks a strong UV-absorbing chromophore. Due to its physicochemical properties, CE in combination with capacitively coupled contactless conductivity detection was chosen. The separation method uses a BGE composed of 40 mM 2-(N-morpholino)ethanesulphonic acid monohydrate and 40 mM L-histidine, pH 6.35. A 0.6 mM N-cetyltrimethyl ammonium bromide (CTAB) solution was added as electroosmotic flow modifier in a concentration below the critical micellar concentration (CMC). Ammonium acetate 50 mg/L was used as internal standard. In total, 30 kV was applied in reverse polarity on a fused-silica capillary (65/41 cm; 75 μm id). The optimized separation was obtained in less than 6 min with good linearity (R(2)=0.9999) for kanamycin. It shows a good precision expressed as RSD on the relative peak areas equal to 0.3 and 1.1% for intra-day and inter-day precision, respectively. The LOD and LOQ are 0.7 and 2.3 mg/L, respectively. Similarly, for sulphate, a good linearity (R(2)=0.9996) and precision (RSD 0.4 and 0.6% for intra-day and inter-day, respectively) were obtained.     

Simultaneous determination of celecoxib, meloxicam, and rofecoxib using capillary electrophoresis with surfactant and application in drug formulations

A simple and selective CE using surfactant with UV detection is described for the simultaneous determination of selective cyclooxygenase-2 inhibitors, celecoxib, meloxicam, and rofecoxib. The simultaneous analysis of celecoxib, meloxicam, and rofecoxib was performed in Tris buffer (10 mM; pH 11) with 60 mM sodium octane-sulfonate and 20% ACN as an anionic surfactant and organic modifier, respectively. Under this condition, good separation with high efficiency and the required short analysis time is achieved. The linear ranges of the method for the determination of celecoxib, meloxicam, and rofecoxib were over 5-100 microg/mL; the detection limits at 200 nm (S/N = 3; injection 3.45 kPa, 5 s) were 2, 1, and 1 microg/mL, respectively. The small amount of sample required and the expeditiousness of the procedure allow content uniformity to be determined in individual pharmaceutical products.     

Determination of tobramycin in human serum by capillary electrophoresis with contactless conductivity detection

A study on the determination of the antibiotic tobramycin by CE with capacitively coupled contactless conductivity detection is presented. This method enabled the direct quantification of the non-UV-absorbing species without incurring the disadvantages of the indirect approaches which would be needed for optical detection. The separation of tobramycin from inorganic cations present in serum samples was achieved by optimizing the composition of the acetic acid buffer. Field-amplified sample stacking was employed to enhance the sensitivity of the method and a detection limit of 50 microg/L (S/N = 3) was reached. The RSDs obtained for migration time and peak area using kanamycin B as internal standard were typically 0.12 and 4%, respectively. The newly developed method was validated by measuring the concentration of tobramycin in serum standards containing typical therapeutic concentrations of 2 and 10 mg/L. The recoveries were 96 and 97% for the two concentrations, respectively.     

Spectrophotometric determination of amikacin,kanamycin, neomycin and tobramycin

A spectrophotometric method for determination of neomycin, kanamycin, tobramycin and amikacin is proposed, based on the Rimini test with disodium pentacyanonitrosylferrate(II) for primary and secondary aliphatic amines. The absorbance of the coloured addition product is measured. Beer's law is valid over a wide concentration range. The method is relatively fast and can be used in control of the manufacture of the antibiotics and their purity, instead of the much slower microbiological method. It is also applicable for determination of these antibiotics in formulations.     

High-performance liquid chromatographic procedure for routine residue monitoring of seven sulfonamides in milk

A simplified method for routine monitoring of 7 residual sulfonamides (SAs) (sulfadiazine (SDZ), sulfamerazine (SMR), sulfadimidine (SDD), sulfamonomethoxine (SMM), sulfamethoxazole (SMX), sulfadimethoxine (SDM), and sulfaquinoxaline (SQ)) in milk using high-performance liquid chromatography (HPLC) with a photodiode array detector is described. The spiked and blank samples were cleaned up by using an Ultrafree-MC/PL centrifugal ultrafiltration unit. For determination/identification, a Mightysil RP-4 GP column and a mobile phase of 25% (v/v) ethanol in water with a photodiode array detector were used. Average recoveries from milk samples spiked with 0.05, 0.1, 0.2, and 0.5 microg mL(-1) of each drug were >82%. The inter- and intra-assay variabilities were 2.0-3.1%. The practical detection limits for 7 SAs were 0.005-0.02 microg mL(-1). The total time and amount of solvent required for the analysis of one sample were <40 min and <6 mL of ethanol, respectively. No toxic solvents were used.     

气相色谱–质谱法测定纤维板和刨花板中邻苯二甲酸酯类增塑剂

建立气相色谱–质谱方法测定纤维板和刨花板中6种邻苯二甲酸酯的方法。样品用正己烷提取后,采用HP–5MS毛细管柱(30 m×0.25 mm,0.25μm)分离,以内标法进行定量。邻苯二甲酸酯BBP,DBP,DEHP,DNOP在0.2~2μg/m L范围内线性均良好,检出限为2 mg/kg;DINP,DIDP在2.0~20μg/m L范围内线性均良好,检出限为10 mg/kg。线性相关系数均大于0.999。样品加标回收率为86.00%~95.17%,测定结果的相对标准偏差为3.06%~9.72%(n=6)。该方法具有较高的灵敏度,可应用于各类纤维板和刨花板产品中邻苯二甲酸酯类增塑剂的检测。     

混合型离子交换液相色谱-串联质谱法测定蜂蜜中5种氨基糖苷类抗生素残留

建立了混合型离子交换液相色谱-串联质谱测定蜂蜜中链霉素、双氢链霉素、壮观霉素、卡那霉素和阿米卡星等5种氨基糖苷类抗生素的方法。蜂蜜样品采用磷酸盐缓冲溶液提取，分子印迹固相萃取柱富集净化，Obelisc R色谱柱分离，以0.1%（v/v）甲酸水溶液和乙腈为流动相进行梯度洗脱，采用电喷雾电离、正离子模式扫描，多反应监测模式检测，外标法定量。实验结果表明，链霉素和双氢链霉素在5~100 μg/L范围内呈现良好的线性关系，定量限为5 μg/kg；壮观霉素、卡那霉素和阿米卡星在20~500 μg/L范围内呈现良好的线性关系，定量限为20 μg/kg。在空白蜂蜜样品中添加1倍、2倍和5倍定量限水平的5种氨基糖苷类药物，其平均回收率为75.1%~92.3%，相对标准偏差为4.5%~10.7%。该法不添加离子对试剂，可减少对质谱仪的污染，并具有较高的灵敏度，适用于蜂蜜中5种氨基糖苷类抗生素的同时检测。     

高效阴离子交换色谱-脉冲安培检测法测定烤烟中的水溶性葡萄糖、果糖和蔗糖

用高效阴离子交换色谱-脉冲安培检测法（HPAEC-PAD）测定了烤烟中的水溶性葡萄糖、果糖和蔗糖。采用水浸取及膜过滤法处理烤烟样品,以Dionex CarboPac PA-1阴离子交换柱为色谱柱,0.2 mol/L NaOH水溶液为淋洗液进行分离测定。葡萄糖、果糖和蔗糖的含量与其峰面积的线性关系良好,回收率均在97%以上。方法简便易行,灵敏度高,重现性良好,可以实现对烟草中单糖的快速分离和测定。     

HPLC‐ELSD determination of kanamycin B in the presence of kanamycin A in fermentation broth

A novel method for the direct determination of kanamycin B in the presence of kanamycin A in fermentation broth using high performance liquid chromatography with evaporative light scattering detector (HPLC‐ELSD) was developed. An Agilent Technologies C₁₈ column was utilized, evaporation temperature of 40°C and nitrogen pressure of 3.5 bar, the optimized mobile phase was water–acetonitrile (65:35, v/v), containing 11.6 mm heptafluorobutyric acid (isocratic elution with flow rate of 0.5 mL/min) with the gain 11. Kanamycin B was eluted at 5.6 min with an asymmetry factor of 1.827. The method showed good linearity over the concentration range of 0.05 to 0.80 mg/mL for the kanamycin B (r² = 0.9987). The intra‐day and inter‐day coefficients of variation obtained from kanamycin B were less than 4.3%. Mean recovery of kanamycin B from spiked fermentation broth was 95%. The developed method was applied to the determination of kanamycin B without any interference from other constituents in the fermentation broth. This method offers simple, rapid and quantitative detection of kanamycin B. Copyright © 2014 John Wiley & Sons, Ltd.     

Validated capillary electrophoretic method for the analysis of ivermectin in plasma after intragastric administration in pigs and horses

A capillary electrophoretic (CE) method has been developed for the determination of ivermectin (CAS 70288-86-7), a new generation drug with antiparasitic activity, in pig and horse plasma. The method was statistically validated for its linearity, accuracy, precision and selectivity. The linear range was from 1 to 30 ng mL(-1) with correlation coefficients greater than 0.999. The limit of detection was 0.3 ng mL(-1), while the quantitative limit was 1 ng mL(-1), using a 0.5 mL sample size. The validated procedure was used to determination of pharmacokinetic parameters of ivermectin after ingestion of 0.1 mg for pigs and 0.2 mg dose per kg body weight for horses, respectively. Studies were performed on a group of eight pigs and six horses. There were no significant differences between pigs and horses in any of the estimated pharmacokinetic parameters.     

高效液相色谱-串联质谱法测定调味料中的痕量苯甲酸与山梨酸

建立了调味料中痕量苯甲酸、山梨酸的高效液相色谱-串联质谱检测方法.调味料样品经盐酸酸化后用乙醚多次提取,酸性氯化钠洗涤提取液,挥干后用1 mL90% 0.2 mmol/L NH4OAc(pH 5.0)的乙腈溶液溶解,过膜备用.采用电喷雾负离子电离(ESI-)模式和单反应监控(SRM)模式检测,外标法定量.该方法在0.5...     

Development and validation of a liquid chromatography-mass spectrometry method for the determination of 4,5-diazafluoren-9-one

A new liquid chromatography-mass spectrometry (LC-MS) method is developed and validated for the identification and determination of novel 4,5-diazafluoren-9-one compound. The method employs a Waters XTerra RP-18 column (150 mmx4.6 mm, i.d. 5 microm) with a mobile phase comprised of a (50:50, v/v) mixture of deionized water containing 0.2% acetic acid (solvent A) and methanol (solvent B) at a flow rate of 1 mL/min, at 35 degrees C. The detection is performed with photodiode-array (PDA) set at 210-400 nm and single quadropole mass spectrometer with electrospray ionization (ESI) positive ion mode. The chromatographic separation is achieved in less than 3 min. The linearity is established over the concentration range of 0.1-0.5 mg/mL (r2=1.000). The mean RSD values for intra- and inter-day precision studies are <2%. The recovery of 4,5-diazafluoren-9-one ranged between 99.84 and 99.97%. The limits of detection and quantitation are determined to be 0.58 and 0.1 mg/mL, respectively.     

Mercury speciation and analysis in drinking water by stir bar sorptive extraction with in situ propyl derivatization and thermal desorption-gas chromatography-mass spectrometry

A method for mercury analysis and speciation in drinking water was developed, which involved stir bar sorptive extraction (SBSE) with in situ propyl derivatization and thermal desorption (TD)-GC-MS. Ten millilitre of tap water or bottled water was used. After a stir bar, pH adjustment agent and derivatization reagent were added, SBSE was performed. Then, the stir bar was subjected to TD-GC-MS. The detection limits were 0.01 ng mL(-1) (ethylmercury; EtHg), 0.02 ng mL(-1) (methylmercury; MeHg), and 0.2 ng mL(-1) (Hg(II) and diethylmercury (DiEtHg)). The method showed good linearity and correlation coefficients. The average recoveries of mercury species (n=5) in water samples spiked with 0.5, 2.0, and 6.0 ng mL(-1) mercury species were 93.1-131.1% (RSD<11.5%), 90.1-106.4% (RSD<7.8%), and 94.2-109.6% (RSD<8.8%), respectively. The method enables the precise determination of standards and can be applied to the determination of mercury species in water samples.     

GC-MS法快速测定铅笔涂层中18种光引发剂

建立了快速测定铅笔涂层中18种光引发剂的气相色谱-质谱联用法(GC/MS).样品以二氯甲烷为提取溶剂,在30℃温度下,超声提取30 min后,萃取液用100 mg N-丙基乙二胺(PSA)分散固相萃取净化,以气相色谱-质谱法(GC-MS)测定,外标法定量.18种光引发剂在0.2～4.0 mg/L(或0.1～4.0 mg...