盐酸环丙沙星分子印迹电化学传感器

本文将电化学合成与分子印迹技术相结合,采用循环伏安法在石墨电极表面,形成盐酸环丙沙星(CPX)分子印迹聚吡咯薄膜,制备了CPX分子印迹传感器。实验对传感器的制备条件进行了优化,用铁氰化钾作为活性电子探针,采用方波伏安法研究了传感器性能。结果表明,在1×10~(-8)~1×10~(-4)mol/L范围内,峰电流与CPX浓度负对数呈良好的线性关系,检出限(S/N=3)为3.5×10~(-9)mol/L。传感器对模板分子CPX选择性强,重现性和稳定性好,置于室温下15d峰电流强度无明显变化。     

水杨酸分子印迹电化学传感器的制备及其性能研究

以水杨酸作为模板分子,通过原位聚合法,在玻碳电极表面合成了水杨酸分子印迹聚合物膜,并用方波伏安法对该印迹电极进行了分析研究.当吸附时间为7 min时,印迹电极对水杨酸浓度响应的线性范围为1.0×10-5~2.6×10-5mol/L,检出限(S/N=3)为2.0×10-6mol/L,同一支印迹电极对水杨酸响应值的RSD为...     

磺胺的分子印迹流动注射化学发光方法研究

本研究采用分子印迹技术,以磺胺为目标分子,环氧树脂为功能单体,二乙烯三胺为交联剂,聚乙二醇1000为致孔剂,合成对磺胺分子有强选择性的分子印迹聚合物。以此聚合物为磺胺分子的特异性识别物质,选择高锰酸钾-甲醛-磺胺化学发光体系,结合流动注射分析技术,建立了测定磺胺的高选择性分子印迹-化学发光分析方法。方法的线性范围为1.0×10-6～3.0×10-4 mol/L,相关系数r2=0.9968,检出限为6.0×10-8 mol/L,对5.0×10-5 mol/L磺胺溶液进行11次平行测定,相对标准偏差为3.7%。利用此方法成功测定了合成样品中磺胺的含量。     

自组装分子印迹单层膜修饰电极对L-丝氨酸的检测

以电沉积多孔金膜为基底,L-丝氨酸为模板分子,L-半胱氨酸为功能单体构建了信号放大的自组装分子印迹单层膜修饰电极.电极对L-丝氨酸浓度响应的线性范围为5.0×10-6～2.0×10-4 mol/L,检出限为4.8×10-7 mol/L,灵敏度为215 mA·L·mol-1.由于多孔金膜有效增加了模板分子的固定量,印迹电极响应性能较无多孔金膜修饰的印迹电极有明显提高.     

金属卟啉分子印迹聚合物的合成与性能研究

以5-(4-羟基苯基)-10,15,20-三苯基卟啉锌为印迹分子,4-乙烯基吡啶为功能单体,乙二醇二甲基丙烯酸酯为交联剂,合成了具有金属卟啉识别能力的分子印迹聚合物.紫外可见滴定光谱研究表明,功能单体与印迹分子在聚合前形成1:1的配合物.通过吸附试验、荧光光谱及斯卡查特分析法,考察了分子印迹聚合物对锌卟啉化合物的识别性能.结果表明,印迹聚合物对结构类似的卟啉化合物具有良好的识别能力,对印迹分子荧光性能的影响远大于其对应的非印迹聚合物.在浓度较低时,印迹聚合物对印迹分子的结合常数和最大结合量分别为:1.61×106L/mol和3.22×10-5mol/g.     

分子印迹膜电化学传感器检测土壤中莠去津

本文报道了一种对莠去津有识别特性的分子印迹膜的制备,即在含和不含模板分子(莠去津)的情况下,通过循环伏安技术在金电极表面沉积2-巯基苯并咪唑,制备了2-巯基苯并咪唑聚合膜.利用循环伏安法对印迹和非印迹膜行为进行了评价,对分子印迹膜的影响因素进行了筛选和优化.实验表明,该分子印迹膜对莠去津具有良好的选择性和灵敏度.莠去津的还原峰电流与莠去津的浓度在 1.2 ×10 - 8mal/L～8.0 ×10 - 5mol/ L 范围内具有良好的线性关系( r=0.99862),检出限可达 3.0 ×10 - 9mol/ L.将此传感器用于土壤中莠去津的测定,回收率在90.8% ～ 98.2%之间,取得了很好的结果.     

孔雀石绿分子印迹表面等离子共振传感器的制备及分析应用

利用表面等离子共振(SPR)光谱,结合分子印迹技术,制备了孔雀石绿分子印迹SPR传感器,建立了检测孔雀石绿的分析方法。探讨了pH值对分子印迹膜吸附特性的影响,并在最佳pH下对其吸附选择性进行了考察。研究结果表明,与相应非印迹传感膜相比,孔雀石绿印迹传感膜对孔雀石绿具有较高的吸附选择性能。该方法测定河水及河泥中孔雀绿的线性范围为8.0×10-10~1.0×10-8 mol/L,检出限(S/N=3)分别为8.83×10-11 mol/L和1.55×10-10 mol/L,平均回收率分别为91.97%和93.88%,相对标准偏差分别为1.2%和2.1%。该方法具有简单、快速、灵敏度高、重复性好等特点,适用于河水和河泥中孔雀石绿的测定。     

基于石墨烯的毒死蜱分子印迹电化学传感器的制备及对毒死蜱的测定

利用分子印迹技术,以马来松香丙烯酸乙二醇酯为交联剂,使用自由基热聚合法在石墨烯修饰的玻碳电极表面合成毒死蜱( CPF)分子印迹聚合膜,制得了CPF分子印迹电化学传感器。采用循环伏安法、线性扫描伏安法和电化学交流阻抗法等,考察了此CPF分子印迹膜的电化学性能。在最佳检测条件下,传感器的峰电流与CPF浓度在2.0×10-7~1.0×10-5mol/L范围内呈线性关系,线性方程为Ip(μA)=-7.1834-0.2424C (μmol/L),相关系数r2=0.9959,检出限为6.7×10-8 mol/L(S/N=3)。构建了CPF分子印迹电化学传感器的动力学吸附模型,测得印迹传感器的印迹因子β=2.59,结合速率常数k=12.2324 s。传感器表现出良好的重现性和稳定性,并成功用于实际水样和蔬菜样品中CPF的测定,加标回收率为94.1%~101.4%。     

异丙隆分子印迹敏感膜传感器

在弱酸(pH 5.5)条件下,采用电聚合法在金电极上制备邻氨基酚异丙隆分子印迹膜,对该印迹膜的性能、分子印迹效应和印迹膜对模板分子及其结构相似物的选择性响应等进行了研究.以K3Fe(CN)6为印迹电极和底液间的探针,建立了一种检测异丙隆的方法.该传感器对异丙隆具有良好的选择性和敏感度,异丙隆浓度在1.0×10-7～4.0×10-4 mol/L范围内与K3Fe(CN)6还原峰电流减少量呈线性关系; 检出限为2.95×10-8 mol/L.对农田水中异丙隆含量进行了测定,回收率为99.0%～102.0%.     

磁性粒子表面自组装辛可宁分子印迹电致化学发光传感器

以辛可宁为模板分子、十二烷基硫醇为功能单体,在Fe3 O4@Au纳米粒子表面自组装辛可宁分子印迹膜,构建了新型磁性粒子-分子印迹电化学发光传感器。通过透射电子显微镜对磁性纳米粒子的粒径分布及形貌进行了表征,使用红外光谱对比分析了辛可宁、分子印迹膜洗脱前和洗脱后的结构及成分。结果表明,在最优的实验条件下(0.012 mol/L 硼砂缓冲溶液(pH 9.5),0.8 mmol/L Ru(bpy)2+3),辛可宁浓度的对数在1×10-10~9×10-8 mol/L范围内,与电化学发光强度变化值有良好的线性关系,检出限为3.5×10-11 mol/L。此传感器灵敏度高、选择性好、易于更新,将其用于血清样品的检测,方法回收率为98.8%~104.7%。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.