Determination of lead in whole blood with a simple flow-injection system and computerized stripping potentiometry

An automated (24 samples/hour) procedure is described for the determination of lead (0–1000 μg l^?1) in human blood based on flow-injection stripping potentiometry. The samples are diluted 20-fold with 0.5 M hydrochloric acid containing 100 mg l^?1 mercury and 40 μg l^?1 cadmium (II), and a 1.1 ml aliquot is injected into the flow system. With a mercury-coated carbon fibre as working electrode, lead (II) is determined by using cadmium (II) as internal standard and a calibration graph prepared from bovine blood. Analyses of two human blood reference samples yielded results of 335±37 and 691±24 μg l^?1 lead, the certified values being 332 and 663 μg l^?1, respectively.     

KINETICS OF FORMATION AND STABILITY CONSTANTS OF MONO AND BIS l-TYROSINE COMPLEXES OF Cu(II), Co(II), AND Ni(II)

Abstract

The kinetics and stability constants of l-tyrosine complexation with copper(II), cobalt(II) and nickel(II) have been studied in aqueous solution at 25° and ionic strength 0.1 M. The reactions are of the type M(HL)^(3-n)+ _n-1 + HL- ? M(HL)^(2-n)+_n(k_n, forward rate constant; k_-n, reverse rate constant); where M=Cu, Co or Ni, HL^? refers to the anionic form of the ligand in which the hydroxyl group is protonated, and n=1 or 2. The stability constants (K_n=k_n/k_-n) of the mono and bis complexes of Cu²⁺, Co²⁺ and Ni²⁺ with l-tyrosine, determined by potentiometric pH titration are: Cu²⁺, log K₁=7.90 ± 0.02, log K₂=7.27 ± 0.03; Co²⁺, log K₁=4.05 ± 0.02, log K₂=3.78 ± 0.04; Ni²⁺, log K₁=5.14 ± 0.02, log K₂=4.41 ± 0.01. Kinetic measurements were made using the temperature-jump relaxation technique. The rate constants are: Cu²⁺, k₁=(1.1 ± 0.1) × 10⁹ M ^?1 sec^?1, k_-1=(14 ± 3) sec^?1, k₂=(3.1 ± 0.6) × 10⁸ M ^?1 sec^?1, k^?2=(16 ± 4) sec^?1; Co²⁺, k₁=(1.3 ± 0.2) × 10⁶ M ^?1 sec^?1, k_-1=(1.1 ± 0.2) × 10² sec^?1, k₂=(1.5 ± 0.2) × 10⁶ M ^?1 sec^?1, k_-2=(2.5 ± 0.6) × 10² sec^?1; Ni²⁺, k₁=(1.4 ± 0.2) × 10⁴ M ^?1 sec^?1, k_-1=(0.10 ± 0.02) sec^?1, k₂=(2.4 ± 0.3) × 10⁴ M ^?1 sec^?1, k_-2=(0.94 ± 0.17) sec^?1. It is concluded that l-tyrosine substitution reactions are normal. The presence of the phenyl hydroxyl group in l-tyrosine has no primary detectable influence on the forward rate constant, while its influence on the reverse rate constant is partially attributed to substituent effects on the basicity of the amine terminus.     

Zur Thermochemie der Zinnhalogenide

The enthalpy change of the reaction at 298 K between Br₂ (l) and Sn(c) in CS₂ as solvent giving SnBr₄ (s) has been determined by calorimetry to be (?374, 2±1.4) kJ·mol^?1, [(?89.45±0.33) kcal·mol^?1]. By the same method the heat of solution of SnBr₄ (c) in CS₂ has been found to be (11.9±0.3) kJ·mol^?1, [(2.84±0.08) kcal·mol^?1]. Combining these results, a value of (?386.1±1.5) kJ·mol^?1, [(?92.3±0.4) kcal·mol^?1] is derived for the standard heat of formation of SnBr₄ (c). Substituting this figure in the thermochemical cycle hitherto used for calculating the heat of formation of SnBr₄ (c) gives ?124.3 kcal·mol^?1 for the standard heat of formation of SnCl₄ (l), which is in reasonable agreement with a recent determination of this quantity⁸.     

Picomole‐level Formaldehyde Determination in Gaseous and Beer Samples Using Flow Injection Chemiluminescence Analysis

Based on the linear enhancement of formaldehyde (FA) within 7.0 ～ 1000 pmol l^?1 on luminol—bovine serum albumin (BSA) chemiluminescence (CL) system, FA determination in air and beer samples using CL with flow injection (FI) was proposed. The detection limit was 2.5 pmol l^?1 (3σ) and the relative standard deviations were less than 4.5% (n = 7). At a flow rate of 2.0 mL min^?1, a whole analysis from sampling to washing only needed 32 s, offering a sample throughput of 112 h^?1. This proposed method was successfully utilized to determine FA vapor pressure in liquid (121.8 ± 3.8 Pa), FA content in real air sample (8.93 ± 0.03 mg m^?3), and FA levels in beer (199.5 ± 5.6 ～ 225.2 ± 3.5 mg l^?1), giving determination recoveries from 90.7% to 109.3%. The mechanism of BSA—FA interaction was also investigated, showing FA binding to BSA was a spontaneous process mainly through hydrogen bonding and van der Waals force by FI‐CL, with binding constant K of 1.89 × 10⁶ l mol^?1 and the number of binding sites n of 0.86. Molecular docking analysis further revealed FA could enter into the pocket at subdomain IIA of BSA, with K of 1.71 × 10⁵ l mol^?1 and ΔG of ‐29.68 kJ mol^?1.     

Spectrofluorimetric determination of niobium with morin enhanced by cetyltrimethylammonium bromide micelles

The effect of surfactants on the fluorescence of the niobium—morin system is described. Cationic surfactants strongly enhanced the intensity (e.g., cetyltrimethylammonium bromide (CTAB) gives an 80-fold increase), while anionic and non-ionic surfactants are without effect. The formation of 1:1 and 1:3 (Nb:morin) complexes is demonstrated spectrophotometrically. The conditional stability constants for these complexes in CTAB micelles are β₁ = (1.14 ± 0.01) × 10⁴ l mol^?1 amd β₃ = (5.66 ± 0.02 × 10¹⁰ l³ mol^?3. The micellar-enhanced fluorimetric method has a 1 μg l^?1 detection limit, and is highly selective. The r.s.d. for the determination of 50 μg l^?1 Nb is 3.5%.     

Comparison of the acute toxicity of tributyltin and copper to veliger larvae of Nassarius reticulatus (L.)

The ban on the use of tributyltin (TBT) is promoting an increasing use of copper as an active biocide in antifouling paints, with consequent rising levels of this metal in the environment. This study assesses the acute toxicity of copper and tributyltin to the larvae of the mollusc gastropod Nassarius reticulatus. Recently hatched veligers were exposed to nominal TBT‐Sn concentrations of 0.9, 1.4, 1.9, 2.8, 3.8, 4.7 and 5.6 µg l^?1 and nominal copper concentrations of 9.4, 23.4, 46.9, 70.3, 93.8, 117.2, 140.6 and 164.1 µg l^?1 for up to 96 h, under static conditions (17 ± 1 °C and 33 ± 1 psu). The percentage of larval mortality was determined for each organometal/metal concentration and exposure time (1, 24, 48, 72 and 96 h). Both TBT and copper had a highly significant effect on larvae survival (p < 0.001) for all times of exposure, except for the first hour in the particular case of TBT. The lowest observed effect concentration for TBT‐Sn decreased over time from 3.8 µg l^?1 at 24 h to 1.9 µg l^?1 at 96 h, whereas for copper it remained constant over time (46.9 µg l^?1). The median lethal concentration (LC₅₀) for TBT‐Sn decreased from 4.87 µg l^?1 at 24 h to 1.78 µg l^?1 at 96 h, and the LC₅₀ for copper decreased from 83.08 µg l^?1 at 24 h to 58.84 µg l^?1 at 96 h. TBT is far more toxic to N. reticulatus larvae than copper. However, owing to the higher copper environmental concentrations, the risk factors of the two biocides may approach each other. This stresses the need to find adequate substitutes for organotin biocides in future antifouling paints. Copyright © 2005 John Wiley & Sons, Ltd.     

Determination of lead in gasoline by a flow-injection technique with atomic absorption spectrometric detection

The gasoline sample is treated with iodine and Aliquat-336 and diluted with 4-methylpentan-2-one; 100 μl is injected into a flowing acetone stream for aspiration into an atomic absorption spectrometer. Calibration is linear in the range 0/2-16 mg l^?1 lead. Results for commercial gasoline samples agree well with those obtained by published titrimetric and atomic absorption methods. The precision for samples containing 300/2-400 mg l^?1 lead is ±1%; with increased recorder amplification, the limit of detection is 0.1 mg l^?1 lead. The method is rapid and economic.     

Quantum yield for photosubstitution of a co group in chromium hexacarbonyl by pyridine

The quantum yield of the photosubstitution of CO by pyridine in cyclohexane has a value of 0.67 ± 0.02 for [Cr(CO)₆] = 3.10^?4 mol l^? and [pyridine] = 10^? mol l^?1.     

The determination of chlorinated long-chain paraffins in water,sediment and biological samples

Methods are described for the routine determination of traces of industrial chloro-n-paraffins having 13–30 carbon atoms and chlorine contents of 42–45% (frw/w), in environmental samples of water, sediments and biota. The procedures are based on thin-layer chromatography detection and measurement. All samples are cleaned up by liquid—solid adsorption chromatography and thin-layer chromatography but those rich in lipids require preliminary solvent extraction. The methods distinguish between chloro-n-paraffins based on long carbon chains (C₂₀–C₃₀) and those based on shorter chains (C₁₃–C₁₇). The methods cover the ranges 500 ng l^?1 to 8 μg l^?1 for water (i.e. from about the solubility limit upwards) and 50 μg kg^?1 to 16 mg kg^?1 for sediments and biota. The precision of the methods ranges from ± 50% relative at the lowest concentrations to ± 12% relative at the highest. Recoveries are about 90% for water, 80% for sediments and between 80 and 90% for biota according to sample type.     

Determination of sulphur dioxide by flow injection analysis with amperometric detection

Sulphur dioxide can be determined at a sampling rate of 120 h^?1, with amperometric detection after separation in a diffusion cell with a teflon membrane. At 25°C, the calibration graph shows two linear ranges, between 0.06 and 6 mg l^?1 and 12 and 110 ml l^? sulphur dioxide, with a detection limit of 0.03 mg l^?1. At 50°C, the liner range is 04–5 mg l^?1, with a detection limit of mg of l^?1. The procedure has been applied to the determination of sulphur dioxide in wines.     

Ion-aggregation and thermal expansion in styrene-based ionomers

The linear thermal-expansion coefficients (α) of styrene–sodium methacrylate copolymers were studied as a function of the concentration of sodium methacrylate comonomer. Over the concentration range studied (0.61–9.0 mole % sodium methacrylate), the expansion coefficients of the glass α_g and of the liquid α_l were independent of ion concentration. Average values for these quantities were α_g = (6.9 ± 0.9) × 10^?5 deg^?1 and α_l = (16.0 ± 2.0) × 10^?5 deg^?1. When samples of concentrations above 6 mole % were heated from room temperature, a low value for the liquid-expansion coefficient α_l was observed in the first runs. This quantity had an average value of (12.0 ± 1.9) × 10^?5 deg^?1. Heating of the 6.5 mole % sample from room temperature followed by cycling from the glass transition temperature T_g to successively higher temperatures resulted in a gradual increase in liquid-expansion coefficient. The results are consistent with the hypothesis of the existence of various types of ionic aggregates in these polymers, with the state of aggregation changing at approximately (5–6) % of ions. Experimental T_g values, which increase with ion concentration over the entire range, are consistent with the results of previous studies.     

An absolute and relative rate study of the reaction of oh radicals with dimethyl sulfide

The gas phase reaction of OH radicals with dimethyl sulfide (CH₃SCH₃, DMS) has been studied using both an absolute and a relative technique at 295 ± 2 K and a total pressure of 1 atm. The absolute rate technique of pulse radiolysis combined with kinetic spectroscopy was applied. Using this technique a rate constant of (3.5 ± 0.2) × 10^?12 cm³ molecule^?1 s^?1 was obtained. For the relative rate method, rate constants for the reaction of OH with DMS were found to increase with increasing concentrations of added NO. These results are compared with the large body of kinetic and mechanistic data previously reported in the literature.     

Copper Catalysed Oxygenation of Bis (2-pyridyl) methane and 6-Methyl-bis (2-pyridyl)methane to the Corresponding Ketones

The ligands (L) bis (2-pyridyl) methane (BPM) and 6-methyl-bis (2-pyridyl)methane (MBPM) form the three complexes CuL²⁺, CuL, and Cu₂L₂H with Cu²⁺. Stability constants are log K₁ = 6.23 ± 0.06, log K₂ = 4.83 ± 0.01, and log K (Cu₂L₂H + 2H²⁺ ? 2 CuL²⁺) = ?10.99 ± 0.03 for BPM and 4.56 ± 0.02, 2.64 ± 0.02, and ?11.17 ± 0.03 for MBPM, respectively. In the presence of catalytic amounts of Cu²⁺, the ligands are oxygenated to the corresponding ketones at room temperature and neutral pH. With BPM and 2,4,6-trimethylpyridine (TMP) as the substrate and the buffer base, respectively, the kinetics of the oxygenation can be described by the rate law with k₁ = (5.9 ± 0.2) · 10^?13 mol l^?1 s^?1, k₂ = (4.0 ± 0.6) · 10^?4 mol^?1 ls^?1, k₃ = (1.1 ± 0.1) · 10^?12 mol l^?1 s^?1, and k₄ = (9 ± 2) · 10^?14 mol l^?1 s^?1.     

Green and efficient extraction strategy to lithium isotope separation with double ionic liquids as the medium and ionic associated agent

The paper reported a green and efficient extraction strategy to lithium isotope separation. A 4-methyl-10-hydroxybenzoquinoline (ROH), hydrophobic ionic liquid—1,3-di(isooctyl)imidazolium hexafluorophosphate ([D(i-C₈)IM][PF₆]), and hydrophilic ionic liquid—1-butyl-3-methylimidazolium chloride (ILCl) were used as the chelating agent, extraction medium and ionic associated agent. Lithium ion (Li⁺) first reacted with ROH in strong alkali solution to produce a lithium complex anion. It then associated with IL⁺ to form the Li(RO)₂IL complex, which was rapidly extracted into the organic phase. Factors for effect on the lithium isotope separation were examined. To obtain high extraction efficiency, a saturated ROH in the [D(i-C₈)IM][PF₆] (0.3 mol l^?1), mixed aqueous solution containing 0.3 mol l^?1 lithium chloride, 1.6 mol l^?1 sodium hydroxide and 0.8 mol l^?1 ILCl and 3:1 were selected as the organic phase, aqueous phase and phase ratio (o/a). Under optimized conditions, the single-stage extraction efficiency was found to be 52 %. The saturated lithium concentration in the organic phase was up to 0.15 mol l^?1. The free energy change (ΔG), enthalpy change (ΔH) and entropy change (ΔS) of the extraction process were ?0.097 J mol^?1, ?14.70 J mol K^?1 and ?48.17 J mol^?1 K^?1, indicating a exothermic process. The partition coefficients of lithium will enhance with decrease of the temperature. Thus, a 25 °C of operating temperature was employed for total lithium isotope separation process. Lithium in Li(RO)₂IL was stripped by the sodium chloride of 5 mol l^?1 with a phase ratio (o/a) of 4. The lithium isotope exchange reaction in the interface between organic phase and aqueous phase reached the equilibrium within 1 min. The single-stage isotope separation factor of ⁷Li–⁶Li was up to 1.023 ± 0.002, indicating that ⁷Li was concentrated in organic phase and ⁶Li was concentrated in aqueous phase. All chemical reagents used can be well recycled. The extraction strategy offers green nature, low product cost, high efficiency and good application prospect to lithium isotope separation.     

A Multicommuted Flow‐based System for Hydrogen Peroxide Determination by Chemiluminescence Detection Using a Photodiode

Abstract

A simple, rapid, and automated assay for hydrogen peroxide in pharmaceutical samples was developed by combining the multicommutation system with a chemiluminescence (CL) detector. The detection was performed using a spiral flow‐cell reactor made from polyethylene tubing that was positioned in front of a photodiode. It allows the rapid mixing of CL reagent and analyte and simultaneous detection of the emitted light. The chemiluminescence was based on the reaction of luminol with hydrogen peroxide catalyzed by hexacyanoferrate(III).

The feasibility of the flow system was ascertained by analyzing a set of pharmaceutical samples. A linear response within the range of 2.2–210 µmol l^?1 H₂O₂ with a LD of 1.8 µmol l^?1 H₂O₂ and coefficient of variations smaller than 0.8% for 1.0×10^?5 mol l^?1 and 6.8×10^?5 mol l^?1 hydrogen peroxide solutions (n=10) were obtained. Reagents consumption of 90 µg of luminol and 0.7 mg of hexacyanoferrate(III) per determination and sampling rate of 200 samples per hour were also achieved.     

Die Bildungsenthalpie von Zinndijodid,SnJ2 (c)

The heat of reaction for SnJ₂ (c)+J₂ (c)+4045 CS₂ (l)=[SnJ₄; 4045 CS₂] (sol) has been determined to be (?41.12±0.55) kJ mol^?1, [(?9.83±0.13) kcal mol^?1] by isoperibol solution calorimetry. Combining this result with the heat of formation of SnJ₄ in CS₂ determined in a previous investigation¹¹ the value (?153.9±1.40) kJ mol^?1, [(?36.9±0.33) kcal mol^?1] has been derived for the heat of formation, ΔH _f ^ι (SnJ₂;c; 298.15 K), of tin diiodide.     

On the mechanism of the Co2(CO)8 catalyzed hydroformylation of olefins in hydrocarbon solvents. A high pressure UV and IR study

High pressure IR and UV spectroscopic experiments confirm the Heck and Breslow mechanism of the hydroformylation of 1-octene and cyclohexene with Co₂(CO)₈ as the starting catalyst. The major repeating unit is HCo(CO)₄, which is formed via the reaction of acylcobalt tetracarbonyl with H₂. The rates are 6.7 × 10^?4 mol l^?1 min^?1 and 8.8 × 10^?5 mol l^?1 min^?1 for 1-octene and cyclohexene, respectively at 80°C and 95 bar CO/H₂ = 1 in methylcyclohexane. The alternative reaction of RCOCo(CO)₄ with HCo(CO)₄ is only a minor pathway, with rates of 1.8 × 10^?5 mol l^?1 min^?1 and 1.1 × 10^?5 mol l^?1 min^?1 for 1-octene and cyclohexene, respectively. It represents an exit from the catalytic cycle. The activation of the catalyst precursor Co₂(CO)₈ is the slowest step of the reaction.     

Photocatalytic Formic Acid Conversion on CdS Nanocrystals with Controllable Selectivity for H2 or CO

Formic acid is considered a promising energy carrier and hydrogen storage material for a carbon‐neutral economy. We present an inexpensive system for the selective room‐temperature photocatalytic conversion of formic acid into either hydrogen or carbon monoxide. Under visible‐light irradiation (λ>420 nm, 1 sun), suspensions of ligand‐capped cadmium sulfide nanocrystals in formic acid/sodium formate release up to 116±14 mmol H₂ g_cat^?1 h^?1 with >99 % selectivity when combined with a cobalt co‐catalyst; the quantum yield at λ=460 nm was 21.2±2.7 %. In the absence of capping ligands, suspensions of the same photocatalyst in aqueous sodium formate generate up to 102±13 mmol CO g_cat^?1 h^?1 with >95 % selectivity and 19.7±2.7 % quantum yield. H₂ and CO production was sustained for more than one week with turnover numbers greater than 6×10⁵ and 3×10⁶, respectively.     

Indirect potentiometric flow-injection determination of silver in photographic fixing solutions

The thiosulfate present in fixing solutions was destroyed on-line by acidification and the undissolved gaseous products were separated from the flow stream by use of polytetrafluoroethylene microporous tubing. The silver was precipitated with an excess of sulfide, and the excess was measured with a silver/silver sulfide electrode. Silver was determined in several ranges from 1 mg 1^?1 to 10 g l^?1.     

An LC–MS/MS method for the quantification of diclofenac sodium in dairy cow plasma and its application in pharmacokinetics studies

An LC–MS/MS method with internal standard tolfenamic acid for determining diclofenac sodium (DCF) in dairy cow plasma was developed and validated. Samples were processed with protein precipitation by cold formic acid–acetonitrile. Determination of DCF was performed using LC–ESI⁺–MS/MS with the matrix‐matched calibration curve. The results showed that the method was sensitive (LOD 2 ng mL^?1, LOQ 5 ng mL^?1), accurate (97.60 ± 5.64%), precise (<10%) and linear in the range of 5–10,000 ng mL^?1. A single intravenous (i.v.) or intramuscular (i.m.) administration of 5% diclofenac sodium injection at a dose of 2.2 mg kg^?1 was performed in six healthy dairy cows according to a two‐period crossover design. The main pharmacokinetic (PK) parameters after a single i.v. administration were as follows: t_1/2β, 4.52 ± 1.71 h; AUC, 77.79 ± 16.76 h μg mL^?1; mean residence time, 5.16 ± 1.11 h. The main PK parameters after a single i.m. administration were as follows: T_max, 2.38 ± 1.19 h; C_max, 7.46 ± 1.85 μg mL^?1; t_1/2β, 9.46 ± 2.86 h; AUC 67.57 ± 13.07 h μg mL^?1. The absolute bioavailability was 87.37 ± 5.96%. The results showed that the diclofenac sodium injection had PK characteristics of rapid absorption and slow elimination, and high peak concentration and bioavailability in dairy cows, and that the recommended clinical dosage of diclofenac sodium injection is 2.2 mg kg^?1.