Determination of traces of selenium(IV) by cathodic stripping voltammetry at the hanging mercury drop electrode

Conditions convenient for the determination of traces of seIenium(IV) by cathodic stripping technique are described. Several electrolytes were tested. Three procedures are given in which the troublesome splitting of the stripping peak is eliminated. Suitable conditions include perchloric acid solution at elevated temperature, hydrochloric acid solution after preconcentration at zero current, and perchloric acid solution containing a small amount of iodide. The detection limits are 5 × 10^-9, 2 × 10^-9 and 5 × 10^-10 mol dm^-3, respectively. The time required for the entire procedure is about 30 min starting with a soluble seIenium(IV) sample.     

Electroreduction of diphenyldiazomethane in acetonitrile at a hanging mercury drop electrode

Cyclic voltammetric studies of the reduction of diphenyldiazomethane (Ph₂CN₂) in CH₃CN-Me₄NPF₆ at a hanging mercury drop electrode have established that the halflife of Ph₂CN₂^? is less than l ms at either 8°C or ?37°C.     

Adsorptive stripping voltammetry of chlordiazepoxide at the hanging mercury drop electrode

Controlled adsorptive accumulation at the hanging mercury drop electrode enables 0.8–11 × 10^?5 M chlordiazepoxide to be quantified by differential-pulse stripping voltammetry with accumulation times of 1–3 min. With 3-min accumulation, the peak current is enhanced 12-fold for 1.0 × 10^?7 M chlordiazepoxide compared to the current from differential pulse polarography. The detection limit is 0.9 × 10^?9 M for 4-min accumulation. The procedure is applied to spiked human serum after preseparation of the drug on a Sep-Pak C₁₈ cartridge.     

Anodic stripping voltammetry of germanium at the hanging mercury drop electrode

The Ge(IV)—Ge(0) system was investigated by cyclic and stripping voltammetry at HMDE in acidic pyrogallol medium and in phosphate, borate and carbonate buffers. It was found that germanium electrodeposited from dilute Ge(IV) solutions dissolved anodically forming two peaks corresponding to the oxidation of the unstable homogeneous and stable heterogeneous amalgams. Both peaks can be exploited analytically for the determination of traces of germanium but due to the complex nature of the germanium amalgam the sensitivity and reproducibility of the determinations are lower compared to the results obtained for metals well-soluble in mercury.     

Parameter evaluation for the determination of selenium by cathodic stripping voltammetry at the hanging mercury drop electrode

The behaviour of selenium(IV) in cathodic stripping voltammetry is evaluated systematically. The effects of copper concentration, pH, deposition potential and complexing agents on the stripping peak are examined and criteria are given for the choice of suitable quantitative parameters. The detection limit was found to be 20 ng l^?1 and the background contamination level was 35 ng l^?1. Zinc and lead do not affect the determination of selenium if EDTA is added to the solution whereas cadmium interferes badly; the corresponding mechanisms are discussed.     

Indirect determination of lutetium by differential pulse anodic stripping voltammetry at a hanging mercury drop electrode

Lutetium has been determined by differential pulse anodic stripping voltammetry in an acidic solution containing Zn-EDTA. Lutetium (III) ions liberated zinc (II), which was preconcentrated on a hanging mercury drop electrode and stripped anodically, resulting in peak current linearly dependent on lutetium (III) concentration. Less than 0.4 ng mL⁻¹ lutetium could be detected after a 2 min deposition.      

Voltammetric determination of mesotrione at hanging mercury drop electrode

A study of the electrochemical reduction of the mesotrione pesticide on a hanging mercury drop electrode (HMDE) was performed as a basis for the development of a sensitive analytical method for natural samples. The electrochemical characteristics of herbicide mesotrione dissolved in a phosphate buffer (pH 7.0) have been determined by means of electrochemical techniques such as cyclic voltammetry (CV) and differential pulse voltammetry (DPV) over a wide range of pH from 2.0 to 10.0. The experimental parameters, such as electrolyte type and its pH, pulse amplitude, and scan rate were optimized. The method was applied to the determination of the pesticide in a spiked soil samples. Using this method, a linear calibration curve for mesotrione was obtained up to the 0.1 μM range in pH 7 phosphate buffer solution with a detection limit (S/N = 3) of 50 nM. The method can be applied successfully to the determination of mesotrione in soils. The text was submitted by the authors in English.     

Determination of arsenic by cathodic stripping voltammetry at a hanging mercury drop electrode

Arsenic (III), respectively arsenic(V) after the reduction were determined in model solutions and some inorganic and organic materials by fast scan differential pulse cathodic stripping voltammetry and by direct current cathodic stripping voltammetry with a rapid increase of potential. The accumulation on a hanging mercury drop electrode followed by cathodic stripping was carried out in 0.7–0.8M HCl or 1–2M H₂SO₄ solutions containing Cu(II)-ions. Detection limits calculated from regression parameters was determined to be under 1 ng/ml for the samples containing very low arsenic concentrations. The relative standard deviation did not reach 8% for arsenic contents about of 5 ng/ml.     

Cathodic stripping voltammetry of 2-thioorotic acid at the hanging mercury drop electrode

Controlled adsorptive accumulation of 2-thioorotic acid (6-carboxy-2-thiouracil) on the hanging mercury drop electrode provides the basis for the direct stripping measurement of that compound in the nanomolar concentration level. Differential pulse voltammetry, following 3 min preconcentration, yields a detection limit of 5.0×10^-10 M 2-thioorotic acid. The cathodic stripping response is evaluated with respect to experimental parameters such as preconcentration time and potential, bulk concentration and others. Best results are obtained using a 0.001 M NaOH electrolyte.Two different methods of cathodic stripping voltammetry can be proposed for the determination of 2-thioorotic acid and the reproducibility of these methods is studied.     

Determination of traces of purine by cathodic stripping voltammetry at the hanging copper amalgam drop electrode

In the presence of purine, the copper(II)/copper(Hg) couple splits into copper(II)/copper(I) and copper(I)/copper(Hg) couples, which form two well-separated systems of peaks under voltammetric conditions. The copper(I)/purine complex adsorbs on the electrode surfacer and can be deposited on the electrode surface by electroreduction of copper(II) ions at the HMDE or by electro-oxidation of the hanging copper amalgam drop electrode (HCADE). The deposit can be stripped either cathodically or anodically over the pH range 2–9. The cathodic stripping variant at the HCADE, in solution with pH 2, offers the best results, with linear response for the range 5 × 10^?9–1.5 × 10^?7 mol dm^?3 purine after an accumulation time of 3 min. The detection limit found with the HMDE in the presence of copper(II) ions is higher.     

Adsorptive stripping voltammetry of Tartrazine at the hanging mercury drop electrode in soft drinks

Adsorptive stripping voltammetry was used for the determination of trace amounts of the dye Tartrazine (E-102) by square-wave (SWS) and differential pulse techniques (DPS). Its adsorptive voltammetric behaviour was investigated at different pH media. NH₄Cl/NH₃ buffer solution was chosen as the most suitable, taking into account the sensitivity and definition of the reduction peaks obtained. The effects of the experimental parameters on the determination are discussed. Standard deviations of 3.3% and 2.6% were obtained by SWS and DPS for 100 and 50 μg/L Tartrazine solutions, respectively (n = 10). Both methods were applied to determine the dye in several commercial soft drinks, containing very small amounts of it. Measurements were made directly in the commercial samples. A comparison of the results obtained by the proposed voltammetric methods with those of an HPLC method was also made. Good correlations between the voltammetric results and the values supplied by the manufacturer were found, whereas recoveries of the same order of magnitude were obtained by the HPLC method. Received: 23 May 1996 / Revised: 5 July 1996 / Accepted: 10 July 1996     

Increased sensitivity of anodic stripping voltammetry at the hanging mercury drop electrode by ultracathodic deposition

An improved approach to the anodic stripping voltammetric (ASV) determination of heavy metals, using the hanging mercury drop electrode (HMDE), is reported. It was discovered that using very cathodic accumulation potentials, at which the solvent reduction occurs (overpotential deposition), the voltammetric signals of zinc(II), cadmium(II), lead(II) and copper(II) increase. When compared with the classical methodology a 5 to 10-fold signal increase is obtained. This effect is likely due to both mercury drop oscillation at such cathodic potentials and added local convection at the mercury drop surface caused by the evolution of hydrogen bubbles.     

Low-level determination of silicon in steels by anodic stripping voltammetry on a hanging mercury drop electrode

The sensitive differential pulse anodic stripping voltammetry (DPASV) proposed originally by Ishiyama et al. (2001) has been revised and improved to allow the accurate measurement of silicon on a hanging mercury drop electrode (HMDE) instead of a glassy carbon electrode. We assessed the rate of formation of the partially reduced β-silicododecamolybdate and found that metallic mercury promotes the reaction in the presence of a large concentration of Fe³⁺. The scope of the method has been broadened by carrying out the measurements in the presence of a constant amount of Fe³⁺. The limit of detection (LOD) of the method described in the present paper is 100 μg Si g⁻¹ of steel, with a relative precision ranging from 5% to 12%. It can be further enhanced to 700 ng Si g⁻¹ of steel provided the weight of the sample, the dilution factors, the duration of the electrolysis and the ballast of iron are adequately revised. The tolerance to several interfering species has been examined, especially regarding Al³⁺, Cr³⁺ and Cr VI species. The method was validated using four low-alloy ferritic steels certified by the National Institute of Standards and Technology (NIST). Its application to nickel base alloys as well as to less complicated matrixes is straightforward. It has also been successfully applied to the determination of free silicon into silicon carbide nano-powder.     

Polarographic behaviour of some s-triazine herbicides and their determination by adsorptive stripping voltammetry at the hanging mercury drop electrode

The electrochemical behaviour of six triazine herbicides (atrazine, terbutylazine, desmetryne, prometryne, terbutryne and methoprotryne) was studied by fast scan differential pulse voltammetry (FSDPV) at a static mercury drop electrode and by constant potential coulometry. The adsorption of these compounds at the mercury electrode was employed for their determination by adsorptive stripping voltammetry (AdSV) in Britton-Robinson buffers. The detection limits calculated from regression analyses ranged between 0.1 and 0.9 g/l. Preconcentration (solid phase extraction on a C18 column) was used for the determination of very low contents in water samples. The recovery was 97–99.6%.     

Electrochemistry of diphenylditelluride at the hanging mercury drop electrode in a protic medium

The electrochemical behavior of diphenylditelluride, Phi2Te2, at a hanging mercury drop electrode has been studied in an aqueous-ethanol solution at pH 7 by means of cyclic and ac voltammetry. The appearance of two cathodic peaks has been attributed to the reversible reduction of the first and all the successive monolayers of a film of PhiTe-Hg, which is formed by adsorption of Phi2Te2 at the mercury/solution interface. The different electrochemical properties of such monolayers have been explained.     

Stripping voltammetry of manganese based on chelate adsorption at the hanging mercury drop electrode

A novel electrochemical stripping approach for the trace measurement of manganese is presented. The metal chelate with erichrome black T is adsorbed on a hanging mercury drop electrode, and the subsequent reduction current of the accumulated chelate is measured by voltammetry. Adsorptive preconcentration for 5 min results in a detection limit of 6 × 10^?10 M (32 l^?1). Cyclic voltammetry is used to characterize the redox and interfacial processes. Optimal experimental conditions include a 0.02 M piperazine-N,N′-bis(2-ethanesulfonic acid) solution (pH 12) containing 1 × 10^?6 M eriochrome black T, a preconcentration potential of ?0.80 V, and a linear potential scan. The response is linear up to 2.9 × 10^?7 M, and the relative standard deviation at 1.8 × 10^?7 M is 1.5%. The effects of possible interferences from metal ions or organic surfactants are evaluated.     

Indirect determination of formaldehyde by alternating-current voltammetry at a hanging mercury drop in the presence of oxygen

An alternating-current voltammetric procedure has been developed for the indirect determination of formaldehyde as its hydrazone at a stationary hanging mercury drop over the formaldehyde concentration range from 0.2 to 15 mg/L in a buffer solution of pH 5.6 ± 0.4 without removing dissolved oxygen. An EKOTEST-VA miniature voltammetric analyzer connected to a computer was used. The detection limit for formaldehyde in the proposed procedure was 0.2 mg/L.     

Adsorptive stripping voltammetric determination of dimenhydrinate at a hanging mercury drop electrode

Dimenhydrinate exhibits a single adsorptive stripping peak at a hanging mercury drop electrode after accumulation at 0.0V vs Ag/AgCl electrode at pH 3.8 (acetate buffer). The addition of trace amounts of copper ions enhanced the dimenhydrinate peak and its height depends on the concentration of each dimenhydrinate and Cu²⁺. The adsorptive stripping response was evaluated with respect to accumulation time and potential, concentration dependence, electrolyte, the presence of other purines, surfactants and other metal ions, and some variables. The calibration graph for dimenhydrinate determination is linear over the range 2.0×10^–8–2.0×10^–7 M (pre-concentration for 60s). The correlation factor is found to be 0.985 and RSD is 3.2% at 1.0×10^–7 M. Detection limit is 1.0×10^–8 M after 5 min accumulation. The determination of dimenhydrinate in pharmaceutical formulations by the proposed method is also reported.     

Determination of naringin in grapefruit juice by cathodic stripping differential pulse voltammetry at the hanging mercury drop electrode

A highly sensitive cathodic stripping voltammetric method for the determination of naringin is presented. It is based on the formation and accumulation of two naringin–mercury complexes at the electrode surface, followed by reduction of the surface species during a differential pulse voltammetric scan. The cathodic stripping responses at −0.25 V and −0.42 V, are evaluated with respect to various experimental conditions, such as composition and pH of the supporting electrolyte, naringin concentration, accumulation potential and preconcentration time. The new method is suitable for the determination of naringin concentrations between 0.1 mg l⁻¹ (1.72×10⁻⁷ mol l⁻¹) and 40 mg l⁻¹ (6.88×10⁻⁵ mol l⁻¹). A 3σ limit of detection of 32 μg l⁻¹ (55 nmol l⁻¹) can be reached. The relative standard deviation (r.s.d.) is <1.5%. Recovery experiments yielded a mean recovery of 97% (r.s.d.=4.1%). The application of the procedure to the selective determination of naringin in grapefruit juice is demonstrated.