Cathodic europium(III) electroluminescence at an oxide-coated aluminum electrode

Electroluminescence is produced at an oxide-coated aluminum electrode during cathodic polarization of the electrode in an acetate solution containing nitrate and traces of europium(III). The europium(III) ion in the ⁵D₀ state is the emitter. Linear log-log calibration plots are obtained for the range 1 × 10^?8?1 × 10^?5 M europium(III). A mechanism for the cathodic luminescence is proposed.     

Determination of Electrochemical Electron‐Transfer Reaction Standard Rate Constants at Nanoelectrodes: Standard Rate Constants for Ferrocenylmethyltrimethylammonium(III)/(II) and Hexacyanoferrate(III)/(II)

The most common approximation of electroneutrality is inappropriate for analyzing the voltammetric response of nanoelectrodes. Therefore, the microelectrode theory for extracting the standard rate constant k⁰ for electron transfer from steady‐state voltammograms is invalid for nanoelectrodes. Unlike previous approaches, we considered the influence of the interfacial potential distribution caused by the absence of electroneutrality. We estimated the magnitude of the error at low overpotential incurred as a result of ignoring the absence of electroneutrality and found that it was small. In this region, electrochemical reaction appears to be limited by the rate of electron transfer. Under these conditions, k⁰ can be obtained from steady‐state voltammogram data in a low overpotential region according to an approximate form of the Butler–Volmer equation. This procedure can greatly simplify analysis and calculation of the rate constant k⁰ at nanoelectrodes. Steady‐state voltammogram of equal‐concentration hexacyanoferrate(III)/(II) (Fe(CN) /Fe(CN) ) and ferrocenylmethyltrimethylammonium(III)/(II) (FcTMA²⁺/FcTMA⁺) redox couples were investigated at Pt? Ir nanoelectrodes in the presence of a support electrolyte. k⁰ for Fe(CN) /Fe(CN) and FcTMA²⁺/FcTMA⁺ at Pt? Ir nanoelectrodes were evaluated.     

Studies on the electrode reaction of Cr(III)CyDTA/Cr(II)CyDTA by the coulostatic method in various alcohol + water mixtures

Standard rate constants (k_s)_ms and cathodic transfer coefficients (α_c)_ms of the electrode reaction of Cr(III)CyDTA/Cr(II)CyDTA have been obtained by the coulostatic method in methanol + water, ethanol + water, n-propanol + water and n-butanol + water mixtures, where CyDTA means trans-1,2-cyclohexanediaminetetraacetate. The values of (k_s)_ms obtained at low concentrations of the alcohols are nearly equal to that obtained in aqueous solutions. With increasing concentrations of alcohols, they decrease, in the cases of methanol and n-butanol, in the concentration ranges in which the measurements were made, while, in the cases of ethanol and n-propanol, they decrease to reach minima at certain concentrations and then increase again. The values of (α_c)_ms obtained at high concentrations of n-propanol and n-butanol are much larger than those obtained in aqueous solutions.     

A highly sensitive amperometric sensor for oxygen based on iron(II) tetrasulfonated phthalocyanine and iron(III) tetra-(N-methyl-pyridyl)-porphyrin multilayers

The development of a highly sensitive sensor for oxygen is proposed using a glassy carbon (GC) electrode modified with alternated layers of iron(II) tetrasulfonated phthalocyanine (FeTsPc) and iron(III) tetra-(N-methyl-pyridyl)-porphyrin (FeT4MPyP). The modified electrode showed excellent catalytic activity for the oxygen reduction. The reduction potential of the oxygen was shifted about 330 mV toward less negative values with this modified electrode, presenting a peak current much higher than those observed on a bare GC electrode. Cyclic voltammetry and rotating disk electrode (RDE) experiments indicated that the oxygen reduction reaction involves 4 electrons with a heterogenous rate constant (k_obs) of 3 × 10⁵ mol⁻¹ L s⁻¹. A linear response range from 0.2 up to 6.4 mg L⁻¹, with a sensitivity of 4.12 μA L mg⁻¹ (or 20.65 μA cm⁻² L mg⁻¹) and a detection limit of 0.06 mg L⁻¹ were obtained with this sensor. The repeatability of the proposed sensor, evaluated in terms of relative standard deviation (R.S.D.) was 2.0% for 10 measurements of a solution of 6.4 mg L⁻¹ oxygen. The sensor was applied to determine oxygen in pond and tap water samples showing to be a promising tool for this purpose.     

Comparison of synchronous and laser-induced fluorescence spectroscopy applied to the Eu(III)-fulvate complexation

The complexation of europium ion (Eu(III)) with a soil fulvic acid (FA) has been studied at pH 5 in 0.01 M NaClO₄ by different experimental methods, i.e. synchronous fluorescence spectroscopy (SyFS) and time resolved laser-induced fluorescence spectroscopy (TRLFS). A series of SyFS quenching spectra was obtained by increasing the Eu(III) concentration and keeping the FA concentration constant. The emission spectra and fluorescence lifetimes of the Eu(III) bound to the FA were also measured by a TRLFS system using the same solution used in the SyFS spectral measurement. From the analysis of the fluorescence data obtained by the SyFS and the TRLFS using a non-linear least-squares method, the concentration of the binding sites (C_L) of the FA accessible for the Eu(III) and the corresponding conditional stability constants (log K) were estimated. The two different methods gave rise to constants being comparable with one another. The log K and C_L values (mean ± standard deviation of three determinations) determined by the SyFS were 6.4 ± 0.2 (6.7 ± 0.1 μmol L⁻¹: by the TRLFS) and 10 ± 1 μmol L⁻¹ (7 ± 1 μmol L⁻¹: by the TRLFS), respectively. The applicability of the FA fluorescence quenching techniques for estimating the europium binding parameters was proved by the direct monitoring of the Eu(III) bound to the FA using the TRLFS system.     

UV‐Visible Spectroelectrochemical Detection of Side‐Reactions in the Hexacyanoferrate(III)/(II) Electrode Process

Hexacyanoferrate(III)/(II) system has been studied by UV‐visible long‐pathway spectroelectrochemistry. Three different methodologies, based on potentiodynamic techniques, have been successfully used in the thermodynamic characterization of the system. Formation of soluble Prussian Blue has been detected during the electrode process. The values of the formal potential (E^0′=0.200 V) and the electron stoichiometry of this side‐reaction (n=0.5) have been obtained.     

Electrosorption of Os(III)-complex at single-wall carbon nanotubes immobilized on a glassy carbon electrode: application to nanomolar detection of bromate, periodate and iodate

A simple procedure was developed to prepare a glassy carbon electrode modified with single-wall carbon nanotubes (SWCNTs) and Os(III)-complex. The glassy carbon (GC) electrode modified with CNTs was immersed into Os(III)-complex solution (direct deposition) for a short period of time (60 s). 1,4,8,12-Tetraazacyclotetradecane osmium(III) chloride, (Os(III)LCl₂)·ClO₄, irreversibly and strongly adsorbed on SWCNTs immobilized on the surface of GC electrode. Cyclic voltammograms of the Os(III)-complex-incorporated-SWCNTs indicate a pair of well defined and nearly reversible redox couple with surface confined characteristic at wide pH range (1-8). The surface coverage (Γ) and charge transfer rate constant (k_s) of the immobilized Os-complex on SWCNTs were 3.07 × 10⁻⁹ mol cm⁻², 5.5 (±0.2) s⁻¹, 2.94 × 10⁻⁹ mol cm⁻², 7.3 (±0.3) s⁻¹ at buffer solution with pH 2 and 7, respectively, indicate high loading ability of SWCNTs for Os(III) complex and great facilitation of the electron transfer between electroactive redox center and carbon nanotubes immobilized on the electrode surface. Modified electrodes showed higher electrocatalytic activity toward reduction of BrO₃⁻, IO₃⁻ and IO₄⁻ in acidic solutions. The catalytic rate constants for catalytic reduction bromate, periodate and iodate were 3.79 (±0.2) × 10³, 7.32 (±0.2) × 10³ and 1.75 (±0.2) × 10³ M⁻¹ s ⁻¹, respectively. The hydrodynamic amperometry of rotating modified electrode at constant potential (0.3 V) was used for nanomolar detection of selected analytes. Excellent electrochemical reversibility of the redox couple, good reproducibility, high stability, low detection limit, long life time, fast amperometric response time, wide linear concentration range, technical simplicity and possibility of rapid preparation are great advantage of this sensor.     

Application of the Tris(acetylacetonato)iron(III)/(II) Redox Couple in p‐Type Dye‐Sensitized Solar Cells

An electrolyte based on the tris(acetylacetonato)iron(III)/(II) redox couple ([Fe(acac)₃]^0/1?) was developed for p‐type dye‐sensitized solar cells (DSSCs). Introduction of a NiO blocking layer on the working electrode and the use of chenodeoxycholic acid in the electrolyte enhanced device performance by improving the photocurrent. Devices containing [Fe(acac)₃]^0/1? and a perylene–thiophene–triphenylamine sensitizer (PMI–6T–TPA) have the highest reported short‐circuit current (J_SC=7.65 mA cm^?2), and energy conversion efficiency (2.51 %) for p‐type DSSCs coupled with a fill factor of 0.51 and an open‐circuit voltage V_OC=645 mV. Measurement of the kinetics of dye regeneration by the redox mediator revealed that the process is diffusion limited as the dye‐regeneration rate constant (1.7×10⁸ M ^?1 s^?1) is very close to the maximum theoretical rate constant of 3.3×10⁸ M ^?1 s^?1. Consequently, a very high dye‐regeneration yield (>99 %) could be calculated for these devices.     

Palladium(II)-, Platin(II)-, Ruthenium(II)-, Rhodium(III)- und Iridium(III)-Komplexe von Desoxyfructosazin

Metal Complexes of Biologically Important Ligands. CIII. [1] Palladium(II), Platinum(II), Ruthenium(II), Rhodium(III), and Iridium(III) Complexes of Desoxyfructosazine The reactions of the pyrazine derivative desoxyfructosazin(pz) with K₂PtCl₄ and with the chlorobridged [M(PR₃)Cl₂]₂ (M = Pd, Pt), [(η⁵-C₅Me₅)MCl₂]₂ and [(η⁶-p-Cymol)RuCl₂]₂ give the watersoluble complexes cis-Cl₂Pt(pz)₂, (R₃P)(Cl)M(pz)M(Cl)(PR₃) (M = Pd, Pt), (η⁵-C₅Me₅)(Cl)₂M(pz)M(Cl)₂(η⁵-C₅Me₅) (M = Rh, Ir), (η⁶-p-Cymol)(Cl₂)Ru(pz)Ru(Cl)₂(η⁶-p-Cymol).     

Experimental and calculation methods of studying the effect of second coordination sphere on standard rate constants of charge transfer for Cr(III)/Cr(II) redox couple in chloride melts

The cyclic voltammetry method was used to determine the standard rate constants of charge transfer (k _s) on a glassy carbon electrode for the Cr(III)/Cr(II) redox couple in the systems of NaCl-KCl-CrCl₃, KCl-CrCl₃, and CsCl-CrCl₃ in the temperature range of 973–1173 K. It was shown that k _s grows at an increase in the temperature and decreases as sodium cations are replaced by potassium and cesium cations in the second coordination sphere of chromium complexes. The calculations carried out using the PC GAMESS/Firefly quantum-chemical software by means of the DFT technique showed that the values of the charge transfer activation energy change monotonously in the series of Na-K-Cs in accordance with the ratio of reorganization energies. In its turn, this leads to monotonous variation of the charge transfer rate constants.     

Electrochemical and quantum-chemical studies of chromium(III,II) fluoride complexes in alkali chloride melts

The standard rate constants (k _s) of charge transfer on a glass carbon electrode were determined for the Cr(III)/Cr(II) redox pair in the NaCl-KCl-K₃CrF₆, KCl-K₃CrF₆, and CsCl-K₃CrF₆ systems at 973–1173 K by cyclic voltammetry. The k _s constant was found to increase at elevated temperatures and the following nonmonotonic dependence of k _s on the nature of the outer-spheric cation was found: k _s (CsCl) > k _s (NaCl-KCl) > k _s (KCl). On the basis of quantum-chemical data for the M₃CrF₆ + 18MCl (M = Na, K) model systems, it was shown that the complex chromium particles with four or five outer-spheric sodium or potassium cations had maximum thermodynamic stability. Quantum-chemical calculations were performed to interpret the experimental data on the effect of the second coordination sphere of the complexes on the standard charge transfer rate constants.     

Ruthenium(II), rhodium(III) and iridium(III) based effective catalysts for hydrogenation under aerobic conditions

The new cationic mononuclear complexes [(η⁶-arene)Ru(Ph-BIAN)Cl]BF₄ [η⁶-arene = benzene (1), p-cymene (2)], [(η⁵-C₅H₅)Ru(Ph-BIAN)PPh₃]BF₄ (3) and [(η⁵-C₅Me₅)M(Ph-BIAN)Cl]BF₄ [M = Rh (4), Ir (5)] incorporating 1,2-bis(phenylimino)acenaphthene (Ph-BIAN) are reported. The complexes have been fully characterized by analytical and spectral (IR, NMR, FAB-MS, electronic and emission) studies. The molecular structure of the representative iridium complex [(η⁵-C₅Me₅)Ir(Ph-BIAN)Cl]BF₄ has been determined crystallographically. Complexes 1–5 effectively catalyze the reduction of terephthaldehyde in the presence of HCOOH/CH₃COONa in water under aerobic conditions and, among these complexes the rhodium complex [(η⁵-C₅Me₅)Rh(Ph-BIAN)Cl]BF₄ (4) displays the most effective catalytic activity.     

The electrochemical Peltier effect observed with electrode reactions of Fe(II)/Fe(III) redox couples at a gold electrode

The electrochemical Peltier effect was studied at a gold electrode in solutions containing some Fe(II)/Fe(III) redox couples by measuring the local temperature change in the electrode/solution interphase under controlled-potential and controlled-current polarization. Relative values of the electrochemical Peltier coefficient for the cathodic process at equilibrium potential, which is denoted by (Π_c)_I=0, were determined by analyzing the observed temperature change as a function of current. The values of (Π_c)_I=0 were found to be positive for the Fe(H₂O)₆²⁺/Fe(H₂O)₆³⁺ systems in HClO₄ (1 M), HNO₃ (1 M), H₂SO₄ (0.5 M), and HCl (1 M), their magnitudes being very similar in the first three acid solutions, but smaller in the HCl solution. On the other hand, a negative value of (Π_c)_I=0 was obtained in the case of a Fe(CN)₆^4?/Fe(CN)₆^3? couple in a H₂SO₄ (0.5 M) solution. Such a difference in the Peltier coefficient is considered to be due to the difference in the ionic species of iron involved in the electrode reaction.     

Photophysical and electrochemical properties of heteroleptic tris-cyclometallated Ir(III) complexes

Some new heteroleptic tris-cyclometallated iridium(III) complexes have been synthesized and fully characterized. Among these iridium(III) complexes, bis(1-phenylpyrazolato-N,C^2′)iridium(III)[5-(2′-pyridyl)tetrazolate] (3) and bis(3-methyl-1-phenylpyrazolato-N,C^2′)iridium(III)[5-(2′-pyridyl)tetrazolate] (4) show excellent quantum yields at room temperature, the electron density being perturbed by introducing the pyridyltetrazole ligand, making k_r > k_nr. This destroys the concept of phenylpyrazole based iridium complexes.     

Effects of alkyltrimethylammonium bromide surfactants on the kinetics of the oxidation of tris(1,10-phenanthroline)iron(II) by azido-pentacyanocobaltate(III) complex

The redox reaction between tris(1,10-phenanthroline)iron(II), [Fe(phen)₃]²⁺, and azido-pentacyanocobaltate(III), [Co(CN)₅N₃]^3? was investigated in three cationic surfactants: dodecyltrimethylammonium bromide (DTAB), tetradecyltrimethylammonium bromide (TTAB) and cetyltrimethylammonium bromide (CTAB) in the presence of 0.1?M NaCl at 35°C. Second-order rate constant in the absence and presence of surfactant, k_w and k_ψ, respectively, were obtained in the concentration ranges DTAB?=?0???4.667?×?10^?4?mol?dm^?3, TTAB?=?0–9.364?×?10^?5?mol?dm^?3, CTAB?=?0???6.220?×?10^?5?mol?dm^?3. Electron transfer rate was inhibited by the surfactants with premicelllar activity. Inhibition factors, k_w/k_ψ followed the trend CTAB?>?TTAB?>?DTAB with respect to the surfactant concentrations used. The magnitudes of the binding constants obtained suggest significant electrostatic and hydrophobic interactions. Activation parameters ΔH^≠, ΔS^≠, and E_a have larger positive values in the presence of surfactants than in surfactant-free medium. The electron transfer is proposed to proceed via outer-sphere mechanism in the presence of the surfactants.     

Tast polarography of europium(III)-l-histidine complex

Study of europium(III)-l-histidine complex has been made in sodium perchlorate at μ=0.1 by tast polarography. The reduction process appears to be quasi irreversible. The apparent rate constants have been determined byGellings method¹. With the knowledge ofE ₁ ^2/r and use ofLingane's method, one complex Eu(Histd)²⁺ with the instability constant 6.77×10^?5 is reported.     

The reductions of chloro-, bromo- and iodopentacyanocobaltate(III) anions by titanium(III) in aqueous acidic solution

Summary The reduction of chloro-, bromo- and iodopentacyanocobaltate(III) anions by aquatitanium(III) has been studied in aqueous solution with ionic strength, I = 1.0 mol dm^-3 (LiCl, KBr or KI) at T = 25 °C. The dependence of the observed second-order rate constant, k _obs, on [H⁺] has been investigated over the acid range 0.005–0.100 mol dm ^–3 and is of the general limiting form: k _obs k ₀ + k[H ⁺] ^–1, where k ₀ is appreciable in all cases and k is a composite rate constant. Using values of K _a (associated with the Ti^III hydrolytic equilibrium constant), obtained from the kinetic data for the Ti^III/Co^III redox reactions, and comparison of the rate constants obtained with those for the corresponding V^II reductions of the same Co^III complexes, it is concluded that the Ti^III reductions of these halopentacyanocobaltate(III) complexes proceed via an outer-sphere mechanism.Author to whom all correspondence should be directed, who is presently on leave of absence from Obafemi Awolowo University.     

Charge-transfer kinetics in the Nb(V)/Nb(IV) couple in alkali-metal molten chlorides

Charge-transfer standard rate constants k _s for Nb(V)/Nb(IV) redox couple in KCl-NbCl₅ and CsCl-NbCl₅ chloride melts at glassy carbon and platinum electrodes are determined. The Nb(V) electro-chemical reduction process in the NaCl-KCl (equimolar mixture)-NbCl₅ melt was shown being reversible even at high polarization scan rate (v = 2.0 V s^?1); hence, the determination of k _s appeared impossible. Values of k _s in KCl-NbCl₅ melts are higher than those in CsCl-NbCl₅ melts. Quantum-chemical calculations done in nM⁺[NbCl₆]—model systems by the Discrete Fourier Transformation method showed that the calculated ratio of charge-transfer activation energies in the K⁺-Cs⁺ series corresponds to changes in the experimental charge-transfer rate constants. The charge-transfer standard rate constants increase with the increasing of temperature and with the passing from glassy carbon electrode to platinum one.     

Über die Si-N-bindung: XLI. Kinetische untersuchungen zur hydrolyse von trimethylsilylurethanen des typs Me3Si(p-XC6H4)NCOOEt

Hydrolysis reactions of silylurethanes Me₃Si(p-XC₆H₄)NCOOEt (I) with X = Cl, H or Me in aqueous buffer solutions, with pH values from 1.94 to 10.00 were studied.The catalytic rate constants for the acid and base catalysed reactions and for the “non-catalysed” reaction k(H₃O⁺), k(CH₃COO^?), k(H₂PO₄^?), k(HPO₄^2?), k(NH₃), k(OH^?) and k₀ were evaluated from the pseudo first-order rate constants k_exp determined by UV spectroscopy.The Brönsted coefficients for the base-catalysed reactions were obtained from the catalytic rate constants found and the known constants of dissociation K(HB⁺).The ρ values of the reactions could be derived from the σ constants given by Jaffé.The kientical results obtained are interpreted mechanistically and are believed to also have model character for other nucleophilic substitution reactions with silicon compounds.     

Synthesis of a novel chelating ligand from pentane-2,4-dione and 3-aminopropyl[tris(trimethylsilyloxy)]silane. europium(III) and erbium(III) imino enolates

Acetylacetone reacts with 3-aminopropyl[tris(trimethylsilyloxy)]silane to give a mixture of the isomers 4-[3′-tris(trimethylsilyloxy)silylpropyl]iminopent-2-en-2-ol (90%) and 4-[3′-tris(trimethylsilyloxy)silylpropyl]aminopent-3-en-2-one (10%). According to ¹H and ¹³C NMR data, both isomers exist in the cis-and trans-forms. Anhydrous europium(III) and erbium(III) tris{4-[3′-tris(trimethylsilyloxy)silylpropyl]iminopent-2-en-2-olates} were obtained from the mixture of the isomers and the corresponding propan-2-olates Eu(OPr _i )₃ and Er(OPr _i )₃. The resulting complexes are transparent air-stable liquids that are distillable in vacuo and well soluble in photopolymerizable polyorganosiloxane caoutchoucs and urethane acrylate oligomers. The volatility parameters of the europium(III) complex were studied.