Determination of total copper in haemodialysis water by differential-pulse anodic stripping voltammetry

An anodic stripping voltammetric method was developed in order to determine copper in the water used to prepare haemodialysis solutions. The interference from organic matter was overcome by high-pressure bomb mineralization. The electrochemical results were compared with those obtained by using graphite furnace atomic absorption spectrometry and the correlation was excellent (r = 0.983, p < 0.001). The detection limit was 0.2 μg l^?1 copper.     

Determination of trace arsenic(III) by differential-pulse anodic stripping voltammetry with in-situ plated bismuth-film electrode

Abstract

A systematic survey of the quality status of the main aquifers in rural areas of Catalonia (Spain) regarding pesticide pollution has been carried out. A total number of 139 wells, distributed among 13 different hydrogeological units have been sampled and analyzed by GC-MS and GC-ECD, during the period 1997—98. Pesticides monitored were selected among triazine herbicides, organochlorine and organophosphorus insecticides. A positive presence of pesticides has been detected in 84.2% of the samples analyzed, 23.7% of them exceeding the requirements of the EU drinking water Directive (98/83/CE). Organochlorine insecticides were present in 62.6% of the samples, triazines in 49% and organophosphorus insecticides in 28.8%. The results obtained have been interpreted by Principal Component Analysis.     

Determination of the antibacterial enrofloxacin by differential-pulse adsorptive stripping voltammetry

Two new methods for the determination of enrofloxacin in commercial formulations and canine urine samples, based on adsorptive stripping voltammetry (AdSV), are proposed. One of the proposed method uses univariate calibration to analyse enrofloxacin in commercial formulations and the other applies principal component regression (PCR) to the voltammetric measurements to determine enrofloxacin in the presence of its metabolite ciprofloxacin. The linear concentration ranges of application were 4-25 and 18-55 ng ml⁻¹ by using an accumulation potential of −0.3 V and a 180 or 60 s accumulation time, respectively for the univariate method. The first concentration range was used for the multivariate method. Both methods were successfully applied to the analysis of commercial formulations and spiked canine urine samples, respectively.     

High-accuracy differential-pulse anodic stripping voltammetry with indium as an internal standard

Indium(III) is used as an internal standard for the determination of cadmium, copper and lead at the 20 ng g^?1 level by using differential-pulse anodic stripping voltammetry; the supporting electrolyte is 1.0 mol l^?1 ammonium bromide/0.25 mol l^?1 nitric acid. For each solution, each stripping peak of interest is normalized to the corresponding peak height obtained in the same voltammogram for a known, added concentration of indium(III). A calibration curve is prepared for each element by using these normalized peak heights. The technique is demonstrated for NBS SRM 1643b (Trace Elements in Water). The relative standard deviations for six independent determinations of Cd, Cu, and Pb at the 20 ng g^?1 level are 1.9%, 5.4%, and 1.2%, respectively. The imprecision for copper is limited by the sloping baseline at its stripping potential. The detection limit for each element is less than 1 ng g^?1.     

A modified method for the determination of lead in zircons by differential-pulse anodic stripping voltammetry

Zircons (20–100 mg) are decomposed within 1 h by fusion with potassium hydrogenfluoride followed by fuming with sulphuric acid. With differential-pulse anodic stripping voltammetry, after deposition for 1 min, the limit of detection for lead is 2 ng ml^?1 and the limit of quantitation is 6.6 ng ml^?1. Results (7–247 mg kg^?1 lead) are reported for nine zircons.     

Fumed silica for the direct determination of lead in urine by differential-pulse anodic stripping voltammetry

The use of fumed silica for the direct determination of lead in urine by differential-pulse anodic stripping voltammetry was investigated. Fumed silica, added to urine prior to the nitrogen purge step, completely removed sorption interferences by urinary organic constituents. Values for lead in urine from eight unexposed individuals were 3 ± 2 μg l^?1 or 3 ± 2 μg g^?1 creatinine. This method is a fast, simple and effective means for the accurate determination of lead in undiluted urine without pretreatment.     

Determination of ceftriaxone in biological material by differential-pulse adsorptive stripping voltammetry

Differential-pulse adsorptive stripping voltammetry was used to determine sub-micromolar concentrations of ceftriaxone in plasma. A hanging mercury drop electrode was chosen as the working electrode. A simple clean-up procedure was developed in which ceftriaxone was extracted from blood plasma with the non-ionic resin Amberlite XAD-2 and eluted with methanol. The recovery from plasma was 97.6% using a 1.52 x 10(-4) M stock ceftriaxone solution. The method was applied to caesarean cases, and total ceftriaxone levels were measured in the maternal and umbilical cord blood. The amount of ceftriaxone transmitted to the baby on administration of the drug to the mother before the caesarean operation was found to be in the range 0.067-0.17%.     

Determination of trace metals in rain water by differential-pulse stripping voltammetry

Differential-pulse stripping voltammetry is applied to measure zinc, cadmium, lead and copper by anodic stripping and selenium(IV) by cathodic stripping in rain water at pH 2; subsequently, at pH 9,1, manganese is measured by anodic stripping on the same portion, and cobalt and nickel are measured in the adsorptive mode after formation of their dimethylglyoximates. The instrumental parameters are optimized. The linear ranges, mutual interferences and detection limits are studied. Excellent accuracy is demonstrated; the standard deviation is around 15% at 2.5–50 μg l^?1 levels. The method is shown to be applicable for rain water.     

Optimization and comparison of four mercury working electrodes in speciation studies by differential-pulse anodic stripping voltammetry

Four types of working electrodes are compared with respect to sensitivity, resolution, peak width and suitability for copper speciation studies by differential-pulse anodic stripping voltammetry. The hanging mercury drop electrode, two rotating mercury film electrodes with in-situ and pre-formed films and a stationary mercury film electrode with a vibrationally induced jet-stream are examined. The last electrode appears to be the most useful system with the highest sensitivity. Conditions for mercury film formation must be optimized for each individual electrochemical system in order to avoid erroneous conclusions from standard addition procedures and apparent complexation capacity measurements.     

Determination of indole in shrimps by differential-pulse voltammetry in an emulsified medium

A method has been developed to determine indole in shrimps by differential-pulse voltammetry at a Pt electrode in an emulsified medium, after extraction into hexane - ethyl acetate (49 + 1). The standard additions method was used in order to minimise the matrix effect. Recoveries at the concentration levels of 11.71 and 0.94 micrograms g-1 of shrimp were 82 and 75%, respectively. The relative standard deviations were 3.5 and 4.0%, respectively. The accuracy of the proposed method was verified by comparing the results obtained from the analysis of shrimp samples allowed to decompose at room temperature for 1, 3 and 4 d, with those obtained from a spectrophotometric method by applying Student's t-test.     

Determination of copper in seawater by anodic stripping voltammetry

Copper in surface seawater has been determined using both hanging mercury drop and thin film electrodes. Total copper was found to be in the range 0.4–0.7 μg l^?1, and labile copper in the range 0.2–0.4 μg l^?1. Most of the copper present in seawater is complexed with or adsorbed on organic matter, and a smaller percentage is associated with inorganic colloids. Seawater contains both organic and inorganic compounds which will react with approximately 1×10^?8M added ionic copper. Because of the presence of the complexing agents, peak current-copper concentration calibration curves in seawater are non-linear, and care must be exercised in using spiked results in the calculation of the copper content. The thin film electrode (TFE) is more suitable than the hanging mercury drop electrode for determining copper in seawater, although the TFE results are more dependent on deposition potential, and suffer from interference by nickel if very negative deposition potentials are used.     

Determination of soluble chromium in simulated PWR coolant by differential-pulse adsorptive stripping voltammetry

An analytical method has been developed for the determination of dissolved chromium at concentrations less than 2 mug/l. in PWR coolant by differential-pulse adsorptive stripping voltammetry at a hanging mercury drop electrode. Concentrations above 2 mug/l. can be determined by appropriate dilution of the sample. The method is based on measurement of the current associated with reduction of a chromium(III)-DTPA (diethylenetriaminepenta-acetic acid) complex adsorbed at the surface of the mercury drop. The effects of boric acid, pH, DTPA concentration, accumulation potential and time were investigated together with the oxidation state of the chromium. No interference was observed from other transition metal ions expected to be present in PWR coolant. No alternative chemical technique of similar sensitivity was available for comparison with the results obtained in solutions containing <1 mug/l. chromium. Recoveries from simulated coolant solutions were greater than 95% and the relative standard deviations for single determinations were in the range 12-25%. The statistical limit of detection at the 95% confidence level was 0.023 mug/l. This method of analysis should prove valuable in corrosion studies and is uniquely capable of following the changes in soluble chromium concentration in PWR coolant that follow operational changes in the reactor.     

Determination of zinc in sea-water by anodic stripping voltammetry

The horizontal distribution of zinc in surface waters from Guanabara Bay has been studied by use of optimized voltammetric techniques and ultraclean working procedures. The non-linearity observed between the peak current for zinc and the electrolysis time, as well as the appearance of a peak at −1.16 V, are discussed. The values found for total zinc in the samples range between 0.3 and 22 μg/l.     

Determination of gallium traces by differential pulse anodic stripping voltammetry

Summary The determination of gallium traces is carried out on the hanging drop mercury electrode in solutions of low ionic strength and in absence of complexing agents. At pH=3.2, where stable solutions are obtained, concentrations of 0.2 g Ga l^–1 are determinated with a standard deviation of 0.96% and a detection limit of 4 ng Ga l^–1.The effect of various instrumental parameters is investigated and optimized conditions established. The theory of differential pulse anodic stripping voltammetry is verified with the results obtained experimentally. The use of salicylate as base electrolyte is also considered.

---

Bestimmung von Galliumspuren durch Differentialpuls-Anodic Stripping-Voltammetrie

     

Determination of thallium in natural waters by anodic stripping voltammetry

Thallium was determined in natural waters by anodic stripping voltammetry at a hanging mercury drop electrode, in acetate buffer pH 4.6+EDTA, after preconcentration and separation on an anion exhange resin. For Pacific Ocean surface waters a mean value of 13.0±1.4 ng Tl l^?1 was found, while for freshwater samples the value was 3.7±1.0 ng Tl l^?1. Thermodynamic considerations of thallium speciation predict that both in seawater and freshwater thallium exists primarily in the trivalent state. This was confirmed by experiment.     

Rapid determination of surface-active substances by fast-scan differential-pulse voltammetry

Fast-scan differential-pulse voltammograms of air-saturated acetate buffer and mercury nitrate solutions are presented. The current-voltage curves obtained are markedly influenced by surface-active substances (SAS). The peak potential of the voltammogram shifts to more positive potentials with increasing concentration of the SAS. This effect can be utilized for analytical purposes.     

Simultaneous determination of lead,copper, cadmium and zinc in pure zirconium metal by differential-pulse anodic stripping voltammetry

Zirconium metal (ca. I g) was dissolved in hydrofluoric acid, excess of which was removed by fuming with sulphuric acid. An aliquot of this solution was treated with sodium citrate and adjusted to pH 4.5. Lead, copper and cadmium were deposited on the hanging mercury drop electrode by applying a potential of ?0.8 V vs. Ag/AgCl for 1 min and anodic stripping voltammograms were recorded; the anodic peaks appeared at ?0.51, ?0.14 and ?0.67 V, respectively. In a separate run, zinc was deposited at ?1.2 V and the stripping peak appeared at ?1.1 V. Standard additions were used to quantify these impurities at levels in the low mg kg^?1 range, with relative standard deviations of 5–11%.