Admicelle-enhanced synchronous fluorescence spectrometry for the selective determination of polycyclic aromatic hydrocarbons in water

A simple and rapid method for the highly sensitive determination of polycyclic aromatic hydrocarbons (PAHs) in water was developed. Benzo[a]pyrene, benzo[k]fluoranthene, perylene, and pyrene in water were concentrated into sodium dodecyl sulfate (SDS)-alumina admicelles. The collection was performed by adding SDS and alumina particles into the sample solution at pH 2. After gentle mixing, the resulting suspension was passed through a membrane filter to collect the SDS admicelles containing highly concentrated PAHs. The filter was placed on a slide glass and then covered admicellar layer with a fused silica glass plate before setting in a fluorescence spectrometer. Benzo[a]pyrene, benzo[k]fluoranthene, perylene, and pyrene were selectively determined by the synchronous fluorescence scan (SFS) analysis with keeping wavelength intervals between excitation and emission to 98, 35, 29, and 45 nm, respectively. Because of the minimum spectral overlapping, 1-40 ng l⁻¹ of benzo[a]pyrene, benzo[k]fluoranthene, and perylene as well as 10-150 ng l⁻¹ of pyrene were selectively determined with eliminating the interferences of other 12 PAHs. The detection limits were 0.3 ng l⁻¹ for benzo[a]pyrene, benzo[k]fluoranthene, and perylene, and 1 ng l⁻¹ for pyrene. They were 2-3 orders of magnitude lower than the detection limits in normal aqueous micellar solutions. The application to water analysis was studied.     

Second-derivative constant-wavelength synchronous scan spectrofluorimetry for determination of benzo[b]fluoranthene, benzo[a]pyrene and indeno[1,2,3-cd]pyrene in drinking water

The use of derivative constant-wavelength synchronous scan fluorimetry is reported for the determination of three polycyclic aromatic hydrocarbon pollutants in drinking water (linearity range 0.4-4 mug 1(-1)). The limits of detection (LD) and quantification (LQ) (mug 1(-1)) are 0.01 and 0.07 for benzo[b]fluoranthene, 0.03 and 0.12 for benzo[a]pyrene and 0.19 and 0.57 for indeno[1,2,3-cd]pyrene in the presence of three other pollutants, benzo[k]fluoranthene, benzo[ghi]perylene and fluoranthene. The precision (RSD /= 85%) were satisfactory.     

Resolution of 13 polycyclic aromatic hydrocarbons by constant-wavelength synchronous spectrofluorometry.

A method capable of determining 13 PAHs (acenaphthene, anthracene, benzo[a]anthracene, benzo[a]pyrene, benzo[b]fluoranthene, benzo[k]fluoranthene, chrysene, dibenzo[ah]anthracene, fluoranthene, fluorene, indene[1,2,3-cd]pyrene, phenanthrene and pyrene) in a mixture of 16 EPA PAHs by second derivative synchronous spectrofluorometry in the constant wavelength mode was developed. It has not been possible to determine the following PAHs in the mixture: acenaphthylene, benzo[ghi]perylene and naphthalene. The approach studied allows the sensitive, rapid and inexpensive identification and quantitation of 13 PAHs in a solution of hexane. The detection limits are <1 microg L(-1) (except for chrysene and phenanthrene).     

Micelle-sensitized constant-energy synchronous fluorescence spectrometry for the simultaneous determination of pyrene, benzo[a]pyrene and perylene.

The use of micellar media in constant-energy synchronous fluorescence spectrometry has been proposed. The influence of some aqueous micellar systems on the determination of pyrene, perylene and benzo[a]pyrene has been investigated. The presence of these micellar systems allows their determination in aqueous media, thus avoiding the use of an organic solvent, and greatly enhances the fluorescence signals. The combination of a constant-energy synchronous scanning technique and a micellar system provided a single spectrum for the simultaneous identification and quantitative determination of the three polycyclic aromatic hydrocarbons (PAHs). Further there was no energy transfer among them, making the measurement simple and fast. A constant-energy difference of 2800 cm(-1) was selected. The analytical characteristics of the proposed method in the presence of anionic micelles of sodium dodecylsulfate (SDS) were studied. The detection limits were at a level of ng ml(-1). Analysis of water samples from two different origins spiked with known amount of pyrene, perylene and benzo[a]pyrene also gave satisfactory results, and total average recoveries were greater than 97.1%.     

Error propagation as a factor in selection of measurement intervals for the determination of polycyclic aromatic hydrocarbons by second-derivative spectrofluorimetry

The most suitable wavelength intervals were selected for the determination of 4 polycyclic aromatic hydrocarbons (PAHs; benzo[g,h,i]perylene, dibenzo[a,h]anthracene, pyrene, and triphenylene) in very complex mixtures of 11 PAHs: anthracene, benz[a]anthracene, benzo[a]pyrene, benzo[b]fluoranthene, benzo[g,h,i]perylene, benzo[k]fluoranthene, chrysene, dibenz[a,h]anthracene, phenanthrene, pyrene, and triphenylene. The multiple linear regression algorithm was applied to measurements made in several wavelength intervals previously selected on the basis of sensitivity and minimum number of interfering compounds. Of the different models obtained, those displaying minimum error propagation in the analytical result were selected. By applying the models proposed in this study, we precisely and accurately determined benzo[g,h,i]perylene, dibenz[a,h]anthracene, pyrene, and triphenylene in complex mixtures--a feat that could not be achieved by the use of constant-wavelength spectrofluorimetry in combination with second-derivative techniques.     

Validation of a method for extraction of polycyclic aromatic hydrocarbons from sewage sludge and analysis by GC-MS

In the present study, the solid–liquid extraction with low temperature purification was validated for the determination of 16 polycyclic aromatic hydrocarbons from sewage sludge by gas chromatography-mass spectrometry. Recoveries ranged 70–114% for naphthalene, acenaphthylene, acenaphthene, fluorene, phenanthrene, anthracene, fluoranthene, pyrene, benzo[a]anthracene and chrysene, while the compounds benzo[b]fluoranthene, benzo[k]fluoranthene, benzo[a]pyrene, indeno[1,2,3-cd]pyrene, dibenzo[a,h]anthracene and benzo[g,h,i]perylene showed recoveries of between 40 and 70%. The relative standard deviation was less than 13% for all of the compounds. Negative matrix effect was observed on the 10 compounds with less retention time in the chromatographic analysis and positive matrix effect noticed on the others. The limits of quantification were from 2 to 20 μg kg^?1, about 30 times less than the maximum residue limit allowed in sludge by the European Union. The validated method produced quantification of 11 PAHs in one sludge sample at concentrations ranging 20–2000 μg kg^?1.     

Determination of Polycyclic Aromatic Hydrocarbons in Airborne Particulate by High Performance Liquid Chromatography

This paper presents a trisolvent ultrasonic extraction and HPLC analysis method for the determination of 11 polycyclic aromatic hydrocarbons in air particulate collected on an air filter by a commercial high volume air sampler. A reverse phase column, Vydac 201 TP, and a gradient mobile phase, acetonitrile/water, were used. The 11 PAHs, fluoranthene, pyrene, benz[a]anthracene, chrysene, benzo[b]fluoranthene, benzo[k]fluoranthene, benzo[a]pyrene, dibenz[a, h]anthracene, benzo[ghi]perylene, indeno[1,2,3-cd]pyrene, and coronene were completely resolved under experimental conditions. All the PAHs except coronene were monitored by fluorescence with λ_ex=270 nm, λ_em>389 nm. Coronene was monitored by UV with λ=300 nm. The methodology was evaluated by spiking SRM 1649 with a PAH standard and then going through different extraction procedures and analyzing the PAH concentrations without clean-up. An external standard method was used for quantitation. The recovery yields for fluoranthene, benz[a]anthracene, benzo[a]pyrene, benzo[ghi]perylene and indeno[l,2,3-cd]pyrene were above 90%. The detection limits of PAH with fluorescence at λ_ex=270 nm, λ_em>389 nm ranged from 5.7 pg to 69.5 pg.     

Infrared spectroscopy of matrix-isolated polycyclic aromatic hydrocarbon cations. 2. The members of the thermodynamically most favorable series through coronene

Gaseous, ionized polycyclic aromatic hydrocarbons (PAHs) are thought to be responsible for a very common family of interstellar infrared emission bands. Here the near- and mid-infrared spectra of the cations of the five most thermodynamically favored PAHs up to coronene:phenanthrene, pyrene, benzo[e]pyrene, benzo[ghi]perylene, and coronene, are presented to test this hypothesis. For those molecules that have been studied previously (pyrene, pyrene-d10, and coronene), band positions and relative intensities are in agreement. In all of these cases we report additional features. Absolute integrated absorbance values are given for the phenanthrene, perdeuteriophenanthrene, pyrene, benzo[ghi]perylene, and coronene cations. With the exception of coronene, the cation bands corresponding to the CC modes are typically 2-5 times more intense than those of the CH out-of-plane bending vibrations. For the cations, the CC stretching and CH in-plane bending modes give rise to bands that are an order of magnitude stronger than those of the neutral species, and the CH out-of-plane bends produce bands that are 5-20 times weaker than those of the neutral species. This behavior is similar to that found in most other PAH cations studied to date. The astronomical implications of these PAH cation spectra are also discussed.     

Determination of benzo[a]pyrene in shale oil-by solid-surface fluorescence

A method has been developed for determining benzo[a]pyrene in shale oil by combining dry-column chromatography, thin-layer chromatography and fluorescence spectrometry. A two-step separation method was employed to isolate benzo[a]pyrene from shale oil. Benzo[a]pyrene was identified and determined by detecting its fluorescence directly from chromatoplates; as little as 0.06 ng can be detected. The limit of detection of benzo[a]pyrene in shale oil is ca. 1.2 ppm and the reproducibility of the method is ±2.6 ppm.     

Supercritical fluid extraction of polycyclic aromatic hydrocarbons from liver samples and determination by HPLC-FL

An extraction/clean-up procedure by SFE was developed for isolating PAHs from liver samples for subsequent HPLC-FL determination of ten PAHs in the enriched extract. Recoveries (90-115%) and RSD % (< or =7.7) were satisfactory. When applied to 11 samples of bird of prey (Tyto alba) protected species and classified of special interest, from the Galicia (Northwest to Spain), benzo[ghi]perylene and indeno[1,2,3-cd]pyrene were undetectable; chrysene and benzo[a]pyrene are only detected in one sample; benzo[a]anthracene and benzo[k]fluoranthene are only quantified in one sample and benzo[b]fluoranthene in two samples. The other PAHs, anthracene, fluoranthene and pyrene are present in almost all the samples.     

气相色谱-串联质谱法同时测定卷烟滤嘴中15种多环芳烃

建立了气相色谱-串联质谱同时检测卷烟滤嘴中15种多环芳烃的方法。卷烟滤嘴用二氯甲烷振荡萃取后,经0.22μm有机相滤膜过滤,采用DB-5MS色谱柱(30 m×0.25 mm,0.25μm)进行分离,电子轰击源、正离子模式下以多反应监测模式进行检测,内标法进行定量。15种多环芳烃(苊烯、苊、芴、菲、蒽、荧蒽、芘、苯并[a]蒽、屈、苯并[b]荧蒽、苯并[k]荧蒽、苯并[a]芘、二苯并[a,h]蒽、苯并[g,h,i]苝和茚并[1,2,3-c,d]芘)的线性关系良好,相关系数(R~2)为0.991 4~0.999 9。15种多环芳烃在低、中、高3个添加水平下的平均回收率为81.6%~111.2%;除了芴在低添加水平时相对标准偏差为19.2%外,其他相对标准偏差均小于16%。15种多环芳烃的检出限为0.02~0.24 ng/滤嘴,定量限为0.04~0.80 ng/滤嘴。方法前处理简便,具有快速、准确、灵敏度高及重复性好的优点,适用于卷烟滤嘴中多环芳烃的分析。     

Measurement of benzo[a]pyrene,benzo[k]fluoranthene and benzo[g,h,i]perylene by ultraviolet spectroscopy

Microchimica Acta - The technique for determining benzo[a]pyrene, benzo[k]fhuoranthene, and benzo[g,h,i]perylene respectively inμg amounts by UV absorption measurements is described. The...     

Determination of polycyclic aromatic hydrocarbons from buzzards (Buteo buteo) and tawny owl (Strix aluco) by liquid chromatography with fluorescence detection

Supercritical fluid extraction was applied to the determination of naturally contaminated polycyclic aromatic hydrocarbons (PAHs) in bird tissue by liquid chromatography with fluorescence detection (LC-FL). Recoveries (> 90%) and relative standard deviations (< or = 7.7%) were satisfactory. The levels of 10 PAHs were analyzed in 6 classes of tissues (heart, liver, intestine, muscle, lung, and kidney) of 10 buzzards and 2 tawny owls, predatory birds from the Galicia (northwest Spain). The PAHs found most abundantly were pyrene, fluoranthene, benzo[a]anthracene, and anthracene. Chrysene, benzo[b]fluoranthene, benzo[k]fluoranthene, benzo[ghi]perylene, and indeno[1,2,3-cd]pyrene were not detected. Intestine, kidney, and lung were more polluted than other tissues.     

Infrared Cavity Ringdown Spectroscopy of Jet‐Cooled Polycyclic Aromatic Hydrocarbons

Infrared absorption spectra of the CH stretching region were observed for naphthalene, anthracene, phenanthrene, pyrene, and perylene using a heated, supersonic, slit‐jet source and cavity ringdown spectroscopy. Band positions and intensities recorded with 0.2‐cm^?1 resolution were compared with previous gas‐phase and argon matrix isolation experiments, as well as theoretical calculations. The largest matrix shift in the absorption maximum (‐7.4 cm^?1) was observed for anthracene, with all others shifted by 3.0 cm^?1 or less. Spectral features in the supersonic jet spectrum were generally narrower than those observed in the Ar matrix, with the largest matrix broadening found for the perylene (80 % increase). Low number densities observed for the larger polycyclic aromatic hydrocarbons (PAHs) suggest that the lower vapor pressure of PAHs with catacondensed four‐membered rings and with five‐membered rings other than perylene will not be detectable using our current configuration.     

Optimization of the matrix solid-phase dispersion sample preparation procedure for analysis of polycyclic aromatic hydrocarbons in soils: comparison with microwave-assisted extraction

A fast and simple preparation procedure based on the matrix solid-phase dispersion (MSPD) technique is proposed for the first time for the isolation of 16 polycyclic aromatic hydrocarbons (PAHs) from soil samples. Naphthalene, acenaphthene, fluorene, phenanthrene, anthracene, fluoranthene, pyrene, benz[a]anthracene, chrysene, benzo[e]pyrene, benzo[b]fluoranthene, benzo[k]fluoranthene, benzo[a]pyrene, dibenzo[a,h]anthracene, benzo[g,h,i]perylene, and indeno[1,2,3-c,d]pyrene were considered in the study. Extraction and clean-up of samples were carried out in a single step. The main parameters that affect extraction yield, such as dispersant, type and amount of additives, clean-up co-sorbent and extractive solvent were evaluated and optimized. The addition of an alkali solution in MSPD was required to provide quantitative recoveries. Analytical determinations were carried out by high performance liquid chromatography (HPLC) with fluorescence detection. Quantification limits (between 0.01 and 0.6 ng g(-1) dry mass) were well below the regulatory limits for all the compounds considered. The extraction yields for the different compounds obtained by MSPD were compared with the yields obtained by microwave-assisted extraction (MAE). To test the accuracy of the MSPD technique, the optimized methodology was applied to the analysis of standard reference material BCR-524 (contaminated industrial soil), with excellent results.     

Direct determination of selected polynuclear aromatic hydrocarbons in a coal liquefaction product by synchronous luminescence techniques

Synchronous fluorescence and the room-temperature phosphorescence methods were used to determine selected polynuclar aromatic hydrocarbons in a coal liquid (solvent-refined coal) product without a preseparation step. The procedure identified and quantified ten polynuclear aromatic compounds including anthracene, 2,3-benzofluorene, benzo[a]pyrene, benzo[e]pyrene, carbazole, dibenzothiophene, fluoranthene, fluorene, perylene and pyrene. Standard deviations for repeated determinations ranged from 10–30% for concentrations in the range of 0.1–6 mg g^-1. The data obtained by these methods agree with results by other methods within the estimated experimental uncertainty.     

Resolution of benzo[a]pyrene in complex mixtures of other polycyclic aromatic hydrocarbons. Comparison of two spectrofluorimetric methods applied to water samples

Two spectrofluorimetric methods, second-derivative constant-energy synchronous luminescence (SDCESL) and constant-wavelength synchronous luminescence (CWSL) in combination with multiple linear regression (MLR), for the quantification of benzo[a]pyrene (BaP) at sub-ng mL-1 levels, in the presence of benzo[b]fluoranthene (BbFt), benzo[k]fluoranthene (BkFt), benzo[ghi]perylene (BghiP) and indeno[1,2,3-cd]pyrene (IP), were developed and compared in detail. SDCESL presents lower limits of detection and quantification than CWSL/MLR and also gives more exact and precise results for levels close to the quantification limit. For BaP, SDCESL achieved quantification limits of 0.019 ng mL-1 in river waters and 0.007 ng mL-1 in drinking waters. This work offers a sensitive, precise, accurate, rapid, simple and economic methodology for monitoring BaP in waters for public consumption, meeting all the requirements of the EC Directive 98/83/CE that fixes the maximum admissible limit for this polycyclic aromatic hydrocarbon in drinking waters at of 0.010 ng mL-1.     

The development of solid-surface fluorescence characterization of polycyclic aromatic hydrocarbons for potential screening tests in environmental samples

This paper presents the characterization of polycyclic aromatic hydrocarbons (PAHs) in solid-surface fluorescence as the first step for obtaining new optical sensors for PAHs screening. The fluorescence properties of the EPA-PAHs (naphthalene, acenaphthene, acenaphthylene, fluorene, phenanthrene, anthracene, fluoranthene, pyrene, chrysene, benzo[a]anthracene, benzo[k]fluoranthene, benzo[b]fluoranthene, benzo[a]pyrene, indeno [1,2,3-cd]pyrene, benzo[g,h,i]perylene and dibenzo[a,h]anthracene) on five types of solid-surfaces were evaluated. The experimental variables (pH and percentage of organic solvent in samples) were studied, obtaining different possibilities for making individual sensors for some of these PAHs and the best conditions for developing sensors for PAH screening were also studied.     

The monomethyl and dimethyl derivatives of benzo[e]pyrene

Convenient syntheses of the previously unknown complete set of six isomeric monomethyl derivatives of benzo[e]pyrene, 1-, 2-, 3-, 4-, 9- and 10-methylbenzo[e]pyrene, are described. Syntheses of 1-, 2- and 3-methylbenzo[e]pyrene were accomplished through reaction of 7H-benzanthrene (or its 1-Me derivative as appropriate) with 1, 3-bis(dimethylamino)trimethinium perchlorate (or its 1-Me derivative) followed by thermal electrocyclic ring closure accompanied by elimination and aromatization. The earlier claim¹⁶ that the analogous isomeric benzo[a]pyrene derivatives are principal products of reactions of this type is disproven. Synthesis of 3,6- and 4,5-dimethylbenzo[e]pyrene are also described. The structural assignments of all mono- and dimethyl benzo[e] pyrene products are supported by high resolution 270 MHz proton NMR spectra; the chemical shifts and coupling constants of all aromatic protons are fully assigned.     

Electronic spectroscopy of benzo[g,h,i]perylene and coronene inside helium nanodroplets

We have recorded the electronic spectra of benzo[g,h,i]perylene and coronene and their van der Waals complexes with argon and oxygen with a helium-nanodroplet depletion spectrometer. These molecules differ by the addition of one and two fused benzene rings to perylene, which was previously studied in helium. The coronene spectrum is similar to a previously reported jet-cooled laser-induced fluorescence (LIF) spectrum. The van der Waals complexes with argon and oxygen show different complexation sites and maximum number of adsorbants. We report a vibronically resolved benzo[g,h,i]perylene S(1) <-- S(0) spectrum. The spectral lines are split in a similar way to that of several molecules studied before. However, surprisingly, while the van der Waals complexes with argon are free of the splitting, the complexes with oxygen retain the splitting, with increased linewidth and splitting. We could also observe the S(2) <-- S(0) origin transition of benzo[g,h,i]perylene which was previously observed by cavity ring down spectroscopy. While in general the two spectra are quite similar, the relative intensities and spectral shifts of several lines are different.