HIPS／PP熔融反应共混及其动态力学性质

研究了高抗冲聚苯乙烯（HIPS）／聚丙烯（PP）共混物在过氧化二异丙苯（DCP）存在下的熔融反应过程及其动态力学性质．HIPS在DCP存在下以聚苯乙烯（PS）的降解为主，伴随着聚丁二烯（PB）的交联和接枝，PP在DCP存在下以降解为主，HIPS／PP在DCP存在下以PP同HIPS的反应接枝为主，这种原位生成的增容剂显著地改善了HIPS／PP两组份间的相容性，其分子运动特征较前两者发生明显变化，PS的Tg下降，PB和PP的Tg升高．     

HIPS／SBS共混物的形态结构和性能

通常,高抗冲聚苯乙烯(HIPS)为多相体系,由连续聚苯乙烯(PS)相和分散的聚丁二烯(PB)颗粒组成。PB含量一般为5～15%,粒径范围为0.5～10μm,PB颗粒是交联的,同时含有接枝的PS,其内部结构由制备工艺决定。HIPS力学性能与其制备工艺、PB含量、PB分子结构、相区尺寸及内部结构密切相关。PS和PB嵌段共聚物(SBS)通常为热塑弹性体,由于PS段和PB段的不相容性而呈现微相分离的结构特征。SBS常用于与其它聚合物共混以增加后者的韧性。本工作研究了HIPS/SBS共混物的形态结构和力学性能。     

HIPS／MA接技共聚物对HIPS／PA1010共混体系的增容

制备了高抗冲聚苯乙烯和马来酸酐的接枝共聚物，利用红外光谱，电子能谱和动态力学谱对产物的结构进行了表征，并通过滴定法测定了接枝物中马来酸酐的含量。结果表明马来酸酐接技到了高抗冲聚苯乙烯中顺丁橡胶的分子链上，接技率为４．７％。研究了该接枝共聚物对ＰＡ１０１０／ＨＩＰＳ共混物的增容作用。电镜照片显示，随着共聚物中接枝物含量的增加，分散相相区尺寸明显减小，说明增容效果显著。测定了共混体系的拉伸行为，研究了     

PA6/HIPS/PP-g-(GMA-co-St)反应共混体系的研究

通过扫描电镜、热分析、熔体流动速率、熔融扭矩和力学性能等测试方法研究了甲基丙烯酸缩水甘油酯(GMA)和苯乙烯(St)多单体熔融接枝聚丙烯[PP-g-(GMA-co-St)]对PA6/HIPS共混物的熔融流变性能、结晶行为、相形态和力学性能的影响.结果表明,在熔融共混过程中,PP-g-(GMA-co-St)中的环氧基与PA6的端氨基原位生成的接枝共聚物有效地降低了共混物的界面张力,提高了共混物的界面粘着力,使共聚物的流动速率降低,熔融扭矩提高;PA6分子链的规整性降低,结晶完善性变差.在PP-g-(GMA-co-St)的质量分数为10%时,共混物分散相的尺寸明显减少,力学性能得到较大提高;其中冲击强度超过纯PA6,达到HIPS水平.通过反应共混,制备了力学性能均衡的PA6/HIPS/PP-g-(GMA-co-St)共混物合金.     

SBS-g-GMA对PPO/PBT合金性能影响的研究

采用熔融共混法制备了SBS—g-GMA/PPO/PBT、SBS/PPO/PBT的合金,通过HAAKE、MI、DSC、SEM等方法对合金进行了表征。研究了SBS—g—GMA对PPO/PBT合全相容性的影响,探讨了合全的流变性能、热性能、形态结构和力学性能。     

EPM-g-GMA接枝率的测定及其增韧PBT的力学性能和形态结构研究

在同向双螺杆挤出机中通过熔融接枝反应制备了EPM g GMA ,将其与PBT在转矩流变仪中熔融共混可以获得增韧的PBT工程塑料 .实验中EPM g GMA接枝率的测定采用红外工作曲线法 ,选用CCl4 做溶剂以避免溶剂对样品吸收峰的干扰 .随着EPM g GMA接枝率的增加 ,PBT EPM g GMA的缺口冲击强度相应提高 ,共混物中EPM g GMA的粒径尺寸减小 ,当EPM g GMA的接枝率为 4 7mL 1 0 0gEPM时 ,EPM g GMA的粒径尺寸可达 0 5 μm ,PBT EPM g GMA的缺口冲击强度达到 5 1 6kJ m2 ,是纯PBT的 3 1倍     

多单体接枝聚丙烯对PBT/PP共混体系的形态结构及力学性能影响研究

研究了甲基丙烯酸缩水甘油酯 (GMA)和苯乙烯 (St)多单体熔融接枝聚丙烯 (PP g (GMA co St) )对聚对苯二甲酸丁二酯 (PBT) 聚丙烯 (PP)共混物的形态结构和力学性能的影响 .利用双螺杆挤出机对PBT PP合金进行共混挤出 ,使用DSC、FT IR和SEM、TEM等手段对共混物进行了分析和相形态观察 ,并测试了力学性能 .实验证明 ,熔融共混过程中PP g (GMA co St)的环氧基团可以与PBT的端羧基发生化学反应 ,就地生成了PBT g PP共聚物 ,该共聚物可对PBT PP合金起到良好的增容剂作用 ,使共混物的相区尺寸显著减小 ,共混物的拉伸强度和冲击强度等力学性能同时得到明显改善 ,达到了弹性体系或小分子增容所难以达到的力学性能平衡的效果 .此外 ,TEM的研究还在PBT PP g (GMA co St)共混物中发现了特殊的微相分离结构     

马来酸酐-苯乙烯熔融接枝聚丙烯的影响因素及其性能研究

用单螺杆挤出机制备了马来酸酐 (MAH) 苯乙烯 (St)对聚丙烯 (PP)的多组分单体自由基熔融接枝体系 .研究证实了当两种单体物质的量比约为 1∶1时 ,接枝物的接枝率最高 ,而熔体流动速率 (MFR)最大 .对反应体系影响因素的研究表明单体用量和引发剂用量对不同单体用量比的系列接枝物的接枝率会产生不同的影响 ;另外 ,单体用量增加 ,接枝物的MFR减小 ,过氧化二异丙苯 (DCP)用量增加 ,接枝物的MFR增加 .对多单体熔融接枝聚丙烯PP g (MAH co St)的力学性能研究发现 ,选用合适的单体用量比、单体用量和DCP用量时 ,所制备的接枝物可具有与纯PP相当或更佳的力学性能     

PP—g—（GMA—co—St）对PA6—PC共混合的反应增容作用

用红外、扫描电镜、熔体流动速率和力学性能等测试方法,研究了甲基丙烯酸缩水甘油酯（GMA）和苯乙烯（St）多单体熔融接枝聚丙烯PP－g-(GMA-co-St)对PA6－PC共混合的反应增容作用。研究结果表明,在熔融共混过程中,PP－g-(GMA-co-St)中的环氧基与PA6的端氨基及PC的端羟基原位生成的接枝共聚物就有效地降低了共混物相间的界面张力,明显提高了共混物相界面的粘着力。少量的PP－g-(GMA-co-St)就能使PA6和PC的相容性得到显著改善。当PP－g-(GMA-co-St)的质量分数为10％时,共混物分散相的相区尺寸细化到0．2μm,其力学性能也有较大提高。PA6／PC／PP－g-(GMA-co-St)共混物的力学性能均衡,达到了弹性体增韧体系难以达到的效果。即使PP－g-(GMA-co-St)组分含量为20％时,共混物仍能保持较好的力学性能,特别是在共混物地韧性得以提高的同时,其强度和伸长率也提高。     

生物基超韧聚乳酸复合材料的制备与性能

采用来源于可再生资源的聚醚酰胺弹性体（PEBA）增韧聚乳酸（PLA）制备超韧聚乳酸（PLA/PEBA-GMA）复合材料.为了提高PEBA与PLA之间的相容性,选择极性单体甲基丙烯酸缩水甘油酯（GMA）、共接枝单体乙烯基吡咯烷酮（NVP）及引发剂过氧化二异丙苯（DCP）对PEBA进行接枝改性制备PEBA-GMA.研究了接枝单体组分的用量（m/g）对PLA/PEBA-GMA复合材料性能的影响.研究发现,随着接枝单体组分用量的提高,复合材料的缺口冲击强度逐渐增大,当接枝单体组分GMA,NVP和DCP的用量分别为2.5,2.5和0.25 g时,复合材料的冲击强度高达88.6 kJ/m²,断裂伸长率为164.1%.研究表明,在熔融共混过程中,聚乳酸的端基（—OH和—COOH）与PEBA-GMA上环氧基团发生反应,有效改善两相间的界面相容性,随着接枝单体组分比例的提高,分散相PEBA-GMA的粒子尺寸逐渐减小且分布均匀.     

HIPS-g-GMA相容剂对PC/HIPS共混物相容性的影响*

将两种或两种以上聚合物进行共混是获得性能优异合金材料的简单而有效的途径[1,2 ] .但是大多数聚合物共混时 ,由于混合焓ΔＨ >0且混合熵ΔＳ非常小 ,导致混合自由能大于零 ,故大多数共混体系是不相容的 .而对于不相容的共混 ,由于两相间的界面张力大 ,两相间形成锐形界面 ,两相之间的界面粘结力低 ,导致材料性能很差 .为了改善两相间的相容性 ,需要加入相容剂[3 ,4 ] .绝大多数增容剂是嵌段或接枝共聚物 .这类增容剂分子量较大 ,在加工条件下 ,由于其粘度较大往往难于迁移到两相的界面处 ,起不到应有的增容作用 .聚合物反应加工技术是近 2…     

Investigations of the equilibrium melting temperature in PBT and PC/PBT blends

The melting behavior of poly(butylene terephthalate) and its blends with bisphenol-A polycarbonate was investigated with differential scanning calorimetry. The aim of this work was to determine the equilibrium melting temperature and its dependence on the blend composition using the Hoffman-Weeks plots. It is shown that the critical analysis of various influences on the melting peak is necessary for the reorganization processes and crystallized content of blends. The experimental conditions and the corrections of measured temperatures were derived and discussed. It was found that the use of the extrapolated onset temperature T_m,o of the melting peak is more efficient than the maximum temperature T_m for the Hoffman-Weeks plots. The equilibrium values of pure PBT are determined to be T^o_m,o = 501 K and T^o_m = 506 K. The equilibrium temperatures of the blends do not show a depression with increasing PC content. Using the Nishi-Wang relation, the results can be qualitatively interpreted with a polymer-polymer interaction coefficient χ ≥ 0 between both components. A weak increase in the equilibrium temperature with increasing PC content was observed. A hypothesis to explain this is based on the possibility of a changed population of the different spherulites with various melting temperatures in dependence on PC content. © 1996 John Wiley & Sons, Inc.     

聚对苯二甲酸丁二酯/水滑石纳米复合材料的制备与表征

聚对苯二甲酸丁二酯;水滑石;对苯二甲酸;纳米复合     

Miscibility and crystallization behavior of PBT/epoxy blends

The miscibility and the isothermal crystallization kinetics for PBT/Epoxy blends have been studied by using differential scanning calorimetry, and several kinetic analyses have been used to describe the crystallization process. The Avrami exponents n were obtained for PBT/Epoxy blends. An addition of small amount of epoxy resin (3%) leads to an increase in the number of effective nuclei, thus resulting in an increase in crystallization rate and a stronger trend of instantaneous three‐dimensional growth. For isothermal crystallization, crystallization parameter analysis showed that epoxy particles could act as effective nucleating agents, accelerating the crystallization of PBT component in the PBT/Epoxy blends. The Lauritzen–Hoffman equation for DSC isothermal crystallization data revealed that PBT/Epoxy 97/3 had lower nucleation constant K_g than 100/0, 93/7, and 90/10 PBT/Epoxy blends. Analysis of the crystallization data of PBT/Epoxy blends showed that crystallization occurs in regime II. The fold surface free energy, σ_e = 101.7–58.0 × 10^?3 J/m², and work of chain folding, q = 5.79–3.30 kcal/mol, were determined. The equilibrium melting point depressions of PBT/Epoxy blends were observed and the Flory–Huggins interaction parameters were obtained. It indicated that these blends were thermodynamically miscible in the melt. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 1320–1330, 2006     

PBT/PEG型聚醚酯的鉴定

采用红外光谱、核磁共振和DSC热分析手段对一种未知聚合物样品进行表征。通过对样品红外谱图的吸收峰位和强度及对其核磁共振氢谱中各质子化学位移归属的分析,判明该样品为PBT/PEG型聚醚酯弹性体,且不含游离的聚乙二醇组分。样品的DSC测试表明其与PBT/PEG型聚醚酯的热行为较相符。该分析为此类聚合物提供了一种简单、快速且结果可靠的鉴定方法。     

酯交换反应对PBT／PC共混体系相容性及热行为的影响

研究了ＰＢＴ、ＰＣ间的酯交换反应及共混体系的相容性和热行为。ＩＲ结果表明，在熔融共混过程中ＰＢＴ、ＰＣ间发生了酯交换反应，磷酸三苯酯可在一定程度上抑制酯交换反应的进行，但是当温度过高或共混时间过长时，ＴＰＰ的作用减弱甚至消失。     

PBT／PET共混体系的熔融行为

用差示扫描量热法（ＤＳＣ）考察了ＰＢＴ／ＰＥＴ共混体系的结晶熔融行为，在共混体系中两组份的结晶熔上均随着含量的减小而下降，熔点下降既有形结构变化因素，又有因两组份相容而引起的热力学因素。熔融热焓△Ｈｍ的变化与两组份结晶熔点的变化有相似的规律。这些结果说明在共混体系中ＰＥＴ、ＰＢＴ两组份在结晶一熔融过程中存在相互协同作用，同时也说明ＰＢＴ、ＰＥＴ两组份是晶相分离的，而非晶区是相混容的。     

Crystallization and equilibrium melting behavior of PBT/PETG blends

The results of studies of equilibrium melting point and crystallization behavior of PBT/PETG blends are reported for the first time. A single composition‐dependent glass‐transition temperature is observed in the DSC studies. The isothermal crystallization studies of the blends indicate retardation in crystallization rate as evidenced by the increase in crystallization half time. The retardation in crystallization rate has been attributed to the miscibility in the molten state and the hindrance to the diffusion of crystallizable units. This assumption is further supported by the composition dependence of the crystallization half time. A composition‐dependent melting point depression has been observed which has been attributed to the possible thermodynamic and morphological effects. The interaction parameter calculated by analyzing equilibrium melting point depression shows composition‐dependent negative values confirming the miscibility of the systems. These results are in good agreement with our earlier results on mechanical and dynamic mechanical properties of PBT/PETG blends. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 2439–2444, 1999     

Effect of PBT molecular weight and reactive compatibilization on the dispersed‐phase coalescence of PBT/SAN blends

Poly(butylene terephthalate) (PBT)/styrene‐acrylonitrile copolymer (SAN) blends were investigated with respect to their phase morphology. The SAN component was kept as dispersed phase and PBT as matrix phase and the PBT/SAN viscosity ratio was changed by using different PBT molecular weights. PBT/SAN blends were also compatibilized by adding methyl methacrylate‐co‐glycidyl methacrylate‐co‐ethyl acrylate terpolymer, MGE, which is an in situ reactive compatibilizer for melt blending. In noncompatibilized blends, the dispersed phase particle size increased with SAN concentration due to coalescence effects. Static coalescence experiments showed evidence of greater coalescence in blends with higher viscosity ratios. For noncompatibilized PBT/SAN/MGE blends with high molecular weight PBT as matrix phase, the average particle size of SAN phase does not depend on the SAN concentration in the blends. However noncompatibilized blends with low molecular weight PBT showed a significant increase in SAN particle size with the SAN concentration. The effect of MGE epoxy content and MGE molecular weight on the morphology of the PBT/SAN blend was also investigated. As the MGE epoxy content increased, the average particle size of SAN initially decreased with both high and low molecular weight PBT phase, thereafter leveling off with a critical content of epoxy groups in the blend. This critical content was higher in the blends containing low molecular weight PBT than in those with high molecular weight PBT. At a fixed MGE epoxy content, a decrease in MGE molecular weight yielded PBT/SAN blends with dispersed nanoparticles with an average size of about 40 nm. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2010     

FT-IR/UATR and FT-IR transmission quantitative analysis of PBT/PC blends

Polymer blends are produced to achieve properties that pure polymers are unable to. The qualitative analysis of these blends is not always satisfactory to point out failures in the final product and, therefore, the determination of their content might be required. The aim of this study is to develop quantitative methodologies using Fourier transform infrared spectroscopy (FT-IR), reflection mode with the universal attenuated total reflectance accessory (UATR) and transmission techniques, for the determination of the content of each polymer present in the polymer blend poly (butylene terephthalate) (PBT) and polycarbonate (PC). FT-IR/UATR presented better results using the relative band (A₁₇₇₂/A₁₇₁₆). FT-IR/UATR presented error of 2.30%, which is a little higher than the accuracy limit of the spectrometer (≤2%), but still adequate for industrial applications.