Facile Electrochemical Method for the Fabrication of Stable Corrosion-Resistant Superhydrophobic Surfaces on Zr-Based Bulk Metallic Glasses

Both surface microstructure and low surface energy modification play a vital role in the preparation of superhydrophobic surfaces. In this study, a safe and simple electrochemical method was developed to fabricate superhydrophobic surfaces of Zr-based metallic glasses with high corrosion resistance. First, micro–nano composite structures were generated on the surface of Zr-based metallic glasses by electrochemical etching in NaCl solution. Next, stearic acid was used to decrease surface energy. The effects of electrochemical etching time on surface morphology and wettability were also investigated through scanning electron microscopy and contact angle measurements. Furthermore, the influence of micro–nano composite structures and roughness on the wettability of Zr-based metallic glasses was analysed on the basis of the Cassie–Baxter model. The water contact angle of the surface was 154.3° ± 2.2°, and the sliding angle was <5°, indicating good superhydrophobicity. Moreover, the potentiodynamic polarisation test and electrochemical impedance spectroscopy suggested excellent corrosion resistance performance, and the inhibition efficiency of the superhydrophobic surface reached 99.6%. Finally, the prepared superhydrophobic surface revealed excellent temperature-resistant and self-cleaning properties.     

含氟环氧树脂杂化纳米二氧化硅超疏水材料的制备与性能

目前超疏水材料的制备方法大都存在着制备工艺复杂的缺点。 本文采用传统自由基聚合方法,以甲基丙烯酸缩水甘油酯(GMA)和苯乙烯(St)为单体,合成具有交联性的前驱聚合物P(GMA-r-St)。 再用三氟乙酸(TFA)对其进行接枝改性,制备含氟环氧聚合物P(GMA-r-St)-g-TFA。 利用γ-氨丙基三乙氧基硅烷(KH-550)改性纳米二氧化硅(SiO₂),对其进行傅里叶变换红外光谱(FTIR)、热重(TG)表征。 氨基改性的纳米二氧化硅与含氟环氧聚合物混合制备的超疏水改性材料,棉织物表面经其浸泡,可快速构建超疏水结构。 通过改变改性纳米颗粒的含量,探究其构筑的棉织物的疏水性能和耐溶剂性能。 研究结果表明,经浸泡改性的棉织物,水接触角为160°,耐溶剂性时间为130 min,具备很好的耐溶剂性。 该方法可广泛应用于多种基底材料表面的疏水改性。     

聚苯硫醚超疏水复合涂层的制备与性能

利用工业原料聚苯硫醚微粉和疏水性二氧化硅纳米粉末,采用喷涂法在瓷砖表面制备了疏水复合涂层.研究了热处理温度、组分配比对涂层表面形貌、粗糙度和接触角的影响,发现随着热处理温度升高,涂层表面粗糙度增大,随着疏水性二氧化硅含量的增加,由于表面聚集的疏水性二氧化硅增多,涂层疏水性增强,在热处理温度为280℃、疏水性二氧化硅与聚苯硫醚质量比为1∶1时,可获得超疏水涂层,涂层的接触角大于150°,滚落角小于4°,pH值为1～14的水溶液在其表面都具有很高的接触角.超疏水涂层具有良好的自清洁效果,并且经落沙法实验测定,超疏水涂层耐刮伤性能良好.     

Pore Development during the Carbonization Process of Lignin Microparticles Investigated by Small Angle X-ray Scattering

Application of low-cost carbon black from lignin highly depends on the materials properties, which might by determined by raw material and processing conditions. Four different technical lignins were subjected to thermostabilization followed by stepwise heat treatment up to a temperature of 2000 °C in order to obtain micro-sized carbon particles. The development of the pore structure, graphitization and inner surfaces were investigated by X-ray scattering complemented by scanning electron microscopy and FTIR spectroscopy. Lignosulfonate-based carbons exhibit a complex pore structure with nanopores and mesopores that evolve by heat treatment. Organosolv, kraft and soda lignin-based samples exhibit distinct pores growing steadily with heat treatment temperature. All carbons exhibit increasing pore size of about 0.5–2 nm and increasing inner surface, with a strong increase between 1200 °C and 1600 °C. The chemistry and bonding nature shifts from basic organic material towards pure graphite. The crystallite size was found to increase with the increasing degree of graphitization. Heat treatment of just 1600 °C might be sufficient for many applications, allowing to reduce production energy while maintaining materials properties.     

超声刻蚀法构建分级结构的超疏水表面

在湿法刻蚀和超声空化的基础上, 采用超声刻蚀法制备了具有微纳米分级结构的超疏水表面. 以等体积比的硝酸/乙醇(体积分数为4%)和双氧水(质量分数为30%)的混合溶液作为刻蚀剂, 在室温下对60Si2Mn钢、 60^#钢、 T10钢、 Cr06钢、 65Mn钢和硅钢表面超声刻蚀2~10 min, 构建出多种形貌的微纳米分级结构. 上述表面经氟硅烷修饰后具有超疏水性, 水的表观接触角高达157.0°, 155.8°, 157.4°, 154.9°, 157.6°和156.8°, 滚动角分别为6.5°, 19.2°, 6.1°, 7.8°, 6.7°和7.2°. 与常规刻蚀方法相比, 超声刻蚀的化学刻蚀作用因与空化作用耦合而得到强化和改变, 从而在钢表面构建出分级结构. 由于材料表面微结构形貌和固/液界面接触状态不同, 制得的超疏水表面表现出的润湿行为也不同. 超声刻蚀法简单易行, 成本低廉, 适用于其它金属表面构建微纳米分级结构和超疏水表面.     

Underwater saturation resistance and electrolytic functionality for superhydrophobic nanocomposites

In the current study, water immersion saturation characterization and saturation resistance are investigated for various superhydrophobic polymer nanocomposite coatings. Two different diagnostic methods are used to characterize superhydrophobic performance longevity under continuous water contact: optical reflectivity (associated with captured air layer) and static contact angle (measured immediately after an immersion period). The results indicate that retention of optical reflectivity and superhydrophobicity vary significantly among coatings, and that superhydrophobicity can be lost within a few minutes whereas optical reflectivity can be maintained for hours. Novel electrolytic reactions on electroconductive polymeric nanocomposites can extend superhydrophobic duration by 400 %.     

Application of Nano-Hydroxyapatite Derived from Oyster Shell in Fabricating Superhydrophobic Sponge for Efficient Oil/Water Separation

The exploration of nonhazardous nanoparticles to fabricate a template-driven superhydrophobic surface is of great ecological importance for oil/water separation in practice. In this work, nano-hydroxyapatite (nano-HAp) with good biocompatibility was easily developed from discarded oyster shells and well incorporated with polydimethylsiloxane (PDMS) to create a superhydrophobic surface on a polyurethane (PU) sponge using a facile solution–immersion method. The obtained nano-HAp coated PU (nano-HAp/PU) sponge exhibited both excellent oil/water selectivity with water contact angles of over 150° and higher absorption capacity for various organic solvents and oils than the original PU sponge, which can be assigned to the nano-HAp coating surface with rough microstructures. Moreover, the superhydrophobic nano-HAp/PU sponge was found to be mechanically stable with no obvious decrease of oil recovery capacity from water in 10 cycles. This work presented that the oyster shell could be a promising alternative to superhydrophobic coatings, which was not only beneficial to oil-containing wastewater treatment, but also favorable for sustainable aquaculture.     

Effects of Alcell Lignin Methylolation and Lignin Adding Stage on Lignin-Based Phenolic Adhesives

To investigate the effects of lignin methylolation and lignin adding stage on the resulted lignin-based phenolic adhesives, Alcell lignin activated with NaOH (AL) or methylolation (ML) was integrated into the phenolic adhesives system by replacing phenol at various adhesive synthesis stages or directly co-polymerizing with phenolic adhesives. Lignin integration into phenolic adhesives greatly increased the viscosity of the resultant adhesives, regardless of lignin methylolation or adding stage. ML introduction at the second stage of adhesive synthesis led to much bigger viscosity than ML or AL introduction into phenolic adhesives at any other stages. Lignin methylolation and lignin adding stage did not affect the thermal stability of lignin based phenolic adhesives, even though lignin-based adhesives were less thermally stable than NPF. Typical three-stage degradation characteristics were also observed on all the lignin-based phenolic adhesives. Three-ply plywoods can be successfully laminated with lignin based adhesives, and it was interesting that after 3 h of cooking in boiling water, the plywoods specimens bonded with lignin-based phenolic adhesives displayed higher bonding strength than the corresponding dry strength obtained after direct conditioning at 20 °C and 65% RH. Compared with NPF, lignin introduction significantly reduced the bonding strength of lignin based phenolic adhesives when applied for plywood lamination. However, no significant variation of bonding strength was detected among the lignin based phenolic adhesives, regardless of lignin methylolation or adding stages.     

Valorisation of Lignocellulosic Wastes,the Case Study of Eucalypt Stumps Lignin as Bioadsorbent for the Removal of Cr(VI)

The main objective of this work was to assess Eucalyptus globulus lignin as an adsorbent and compare the results with kraft lignin, which has previously been demonstrated to be an effective adsorbent. Eucalypt lignin was extracted (by the dioxane technique), characterised, and its adsorption properties for Cr(VI) ions were evaluated. The monomeric composition of both types of lignin indicated a high content of guaiacyl (G) and syringyl (S) units but low content of p-hydroxyphenyl (H), with an H:G:S ratio of 1:50:146 (eucalypt lignin) and 1:16:26 (kraft lignin), as determined by Py-GC/MS. According to elemental analysis, sulphur (2%) and sodium (1%) were found in kraft lignin, but not in eucalypt lignin. The adsorption capacity of the eucalypt lignin was notably higher than the kraft lignin during the first 8 h, but practically all the ions had been absorbed by both the eucalypt and kraft lignin after 24 h (93.4% and 95%, respectively). Cr(VI) adsorption onto both lignins fitted well using the Langmuir adsorption isotherm model, with capacities of 256.4 and 303.0 mg/g, respectively, for eucalypt and kraft. The study’s overall results demonstrate the great potential of eucalypt lignin as a biosorbent for Cr(VI) removal from aqueous solutions.     

Engineering of superhydrophobic silica microparticles and thin coatings on polymeric films by ultrasound irradiation

Superhydrophobic coatings are one of the recent hot topics in industrial applications as well as academic studies. The mimicking lotus leaves' superhydrophobic properties have been successfully transferred to real-life applications. However, the current preparation methods used to obtain superhydrophobic coatings are still complex, commonly are not transparent and/or not durable.In the present study, a new relatively simple way to prepare superhydrophobic coatings on polymeric films is described. First, superhydrophobic silica microparticles (MPs) were synthesized by fluorination of SiO₂ MPs produced by a modified Stöber method. Briefly, tetraethyl orthosilicate was polymerized in an ethanol/water continuous phase under basic conditions, and the resultant SiO₂ MPs were dispersed in heptane as a continuous phase and reacted with 1H,1H,2H,2H-perfluorododecyltrichlorosilane (FTS) to yield FTS-SiO₂ MPs, which were dried and dispersed in decane. Superhydrophobic thin coatings were then produced by a ‘throwing stones’ sonication technique and deposited onto polycarbonate, polypropylene, polyethylene, and polyurethane films. The coatings are durable, may be transparent, and exhibit self-cleaning properties for the specific practical applications. The MPs and coated polymeric films were characterized by dynamic light scattering, high-resolution scanning electron microscopy, water contact and sliding angle measurements, and infrared and x-ray photoelectron spectroscopy. This ultrasound-assisted coating process may be upscaled and applied to many polymeric films, for instance polymethyl methacrylate, polystyrene, and polyvinyl chloride. Various applications are envisaged, including but not limited to self-cleaning windows, anti-sticking of snow to antennas and windows, solar panels, roof tiles, agricultural applications, corrosion resistance, and anti-biofouling.     

Thermal and Mechanical Properties of Esterified Lignin in Various Polymer Blends

Lignin is an abundant polymeric renewable material and thus a promising candidate for incorporation in various commercial thermoplastic polymers. One challenge is to increase the dispersibility of amphiphilic lignin in lipophilic thermoplastic polymers We altered Kraft lignin using widely available and renewable fatty acids, such as oleic acid, yielding more than 8 kg of lignin ester as a light brown powder. SEC showed a molecular weight of 5.8 kDa with a PDI = 3.80, while the T_g of the lignin ester was concluded to 70 °C. Furthermore, the lignin ester was incorporated (20%) into PLA, HDPE, and PP to establish the thermal and mechanical behavior of the blends. DSC and rheological measurements suggest that the lignin ester blends consist of a phase-separated system. The results demonstrate how esterification of lignin allows dispersion in all the evaluated thermoplastic polymers maintaining, to a large extent, the tensile properties of the original material. The impact strength of HDPE and PLA blends show substantial loss upon the addition of the lignin ester. Reconverting the acetic acid side stream into acetic anhydride and reusing the catalyst, the presented methodology can be scaled up to produce a lignin-based substitute to fossil materials.     

Supramolecular Design Strategy of a Water-Soluble Diphenylguanidine-Cyclodextrin Polymer Inclusion Complex

Diphenylguanidine (DPG) is a widely used secondary accelerator for the vulcanization of natural rubber (NR) latex. However, its low water solubility and high toxicity limit its use in high-end NR products. In this study, a water-soluble inclusion complex of DPG and a β-cyclodextrin polymer (β-CDP), termed DPG-β-CDP, was prepared through supramolecular interactions and characterized using Fourier-transform infrared spectroscopy, ¹H NMR, scanning electron microscopy, and UV-vis spectroscopy techniques. In comparison with that of DPG, the water solubility of DPG-β-CDP was greatly enhanced because of the water-soluble host molecule. The molar ratio of DPG to the CD unit in β-CDP was determined to be 1:1. At 25 °C, the binding constant of DPG-β-CDP was found to be 9.2 × 10⁵ L/mol by UV-vis spectroscopy. The proposed method for forming inclusion complexes with high potential for use as water-soluble vulcanization accelerators is promising.     

Flammability Tests and Investigations of Properties of Lignin-Containing Polymer Composites Based on Acrylates

In this paper flammability tests and detailed investigations of lignin-containing polymer composites’ properties are presented. Composites were obtained using bisphenol A glycerolate (1 glycerol/phenol) diacrylate (BPA.GDA), ethylene glycol dimethacrylate (EGDMA), and kraft lignin (lignin alkali, L) during UV curing. In order to evaluate the influence of lignin modification and the addition of flame retardant compounds on the thermal resistance of the obtained biocomposites, flammability tests have been conducted. After the modification with phosphoric acid (V) lignin, as well as diethyl vinylphosphonate, were used as flame retardant additives. The changes in the chemical structures (ATR-FTIR), as well as the influence of the different additives on the hardness, thermal (TG) and mechanical properties were discussed in detail. The samples after the flammability test were also studied to assess their thermal destruction.     

Effect of Lignin Structure Characteristics on the Performance of Lignin Based Phenol Formaldehyde Adhesives

As the second most abundant biopolymer, lignin remains underutilized in various industrial applications. Various forms of lignin generated from different methods affect its physical and chemical properties to a certain extent. To promote the broader commercial utilization of currently available industrial lignins, lignin sulfonate (SL), kraft lignin (KL), and organosolv lignin (OL) are utilized to partially replace phenol in the synthesis of phenol formaldehyde (PF) adhesives. The impact of lignin production process on the effectiveness of lignin-based phenolic (LPF) adhesives is examined based on the structural analysis of the selected industrial lignin. The results show that OL has more phenolic hydroxyl groups, lower molecular weight, and greater number of reactive sites than the other two types of lignins. The maximum replacement rate of phenol by OL reaches 70% w/w, resulting in organosolv lignin phenolic (OLPF) adhesives with a viscosity of 960 mPa·s, a minimal free formaldehyde content of 0.157%, and a shear strength of 1.84 MPa. It exhibits better performance compared with the other two types of lignin-based adhesives and meets the requirements of national standards.     

One‐step electrochemical deposition to achieve superhydrophobic cobalt incorporated amorphous carbon‐based film with self‐cleaning and anti‐corrosion

Exploiting a superhydrophobic surface is very significant due to its excellent water repellency which has many practical applications in various fields. In this work, the cobalt incorporated amorphous carbon‐based (Co/a‐C:H) film was prepared successfully on Si substrate via a simple 1‐step electrochemical deposition where electrochemical deposition technology was using cobalt (II) acetylacetonate methanol solution as electrolyte under high voltage, atmospheric pressure, and low temperature. Surprisingly, the as‐prepared film showed a superior superhydrophobic surface with a water contact angle of 153 ± 1° and a sliding angle of 7.6° without any further modification of low surface energy materials. Especially, the tape adhesive, corrosion resistance, and self‐cleaning tests demonstrated that the as‐prepared carbon‐based film could possess fairly well adhesion, superior anti‐corrosion resistance, and self‐cleaning ability, respectively. It indicated that the superhydrophobic Co/a‐C:H film might have potential promising applications in the field of anti‐fouling, anti‐corrosion, and drag resistance, such as the above‐deck structures on icebreaker vessels, ship hulls, and offshore wind turbine blades.     

Preparation of Lignin Carbon/Zinc Oxide Electrode Material and Its Application in Supercapacitors

In this paper, carbon/zinc oxide (LC/ZnO) composites were successfully synthesized and characterized by X-ray powder diffraction, field emission scanning electron microscopy, Fourier transform infrared spectroscopy, Raman, thermogravimetry, and N₂ adsorption–desorption, and tested by electrochemical performance. Studies have shown that the morphology of LC/ZnO composites is that lignin pellets are embedded in ZnO microplates. The lignin carbon in the composites mainly exists in an amorphous structure, and the specific surface area and pore channels of metal oxides are increased by the presence of lignin carbon. The electrochemical performance test shows that the carbonization temperature of LC/ZnO with the highest specific capacitance is 550 °C, and the capacitance retention rate reaches 96.74% after 1000 cycles of testing, indicating that the composite material has good cycle stability. Compared with the control group, it is found that the specific capacitance of LC/ZnO-550 °C is 2.3 times and 1.8 times that of ZnO-550 °C and LC-550 °C, respectively. This shows that during the electrochemical test, the lignin carbon and the metal oxide promote each other and act synergistically. In addition, the composite material exhibits the characteristics of a pseudo-capacitance capacitor, indicating that the redox reaction occurred in the electrochemical performance test.     

Comparison of antioxidant capacities and antioxidant components of commercial bitter melon (Momordica charantia L.) products

In this study, the total phenolic contents and total antioxidant capacities of some commercial bitter melon products (powder, packaged powder, capsule, paste in olive oil), and of unripe and ripe fruits were determined by spectrophotometric and chromatographic methods. The total antioxidant capacities of unripe and ripe bitter melon samples, determined by using the CUPRAC (cupric reducing antioxidant capacity assay) and ABTS (2,2′-azino-bis(3-ethylbenzthiazolin-6-sulfonic acid))/HRP (horseradish peroxidase) methods, were 42.5 and 36.3 µmol TRE (Trolox equivalent) g–1, and 8.7 and 7.0 µmol TRE g–1, respectively. The TAC (total antioxidant capacity) order of the studied samples using the same 2 methods were determined as follows: capsule (CUPRAC value, 140.8; ABTS/HRP value, 143.6 µmol TRE g–1) > packaged powder (129.6; 126.1) > powder (52.3; 64.3) > unripe fruit (42.5; 36.3) > paste in olive oil (17.6; 14.4) > ripe fruit (8.7; 7.0). The order of phenolic content was found as follows: unripe fruit (193.2 µmol GAE (gallic acid equivalent) g-1) > capsule (162.0) > packaged powder (160.6) > powder (83.6) > paste in olive oil (38.3) > ripe fruit (14.6).     

静电组装法在SiO_2表面构筑高分子刷的合成及表征

以对2-溴异丁酸-2′-(对磺苯基)乙酯为引发剂引发苯乙烯发生原子转移自由基聚合,得到的聚合物与NaOH反应转化为端基为磺酸钠的PS(PS-SO3Na).然后采用静电组装方法将PS-SO3Na与表面正离子化的SiO2胶体(SiO2-CBAFS)进行静电组装,得到表面构筑了高分子刷的SiO2胶体/粉体.采用IR、1H-NMR、TG、TEM、AFM、GPC和表面水接触角对组装体系进行结构表征、组装量和部分组装规律研究.结果表明,采用对2-溴异丁酸2′-(对磺苯基)乙酯为引发剂可以制备完全端磺酸基的PS-SO3Na,并且采用静电组装法在SiO2颗粒表面可构筑组装量高达34.4%的高分子刷,有效的提高了高分子刷的组装量;TEM观察下在SiO2胶体颗粒外围可见白色晕圈,PS-SO3Na刷的存在明显改善了SiO2胶体颗粒的分散状态;当样品润洗溶剂由THF变换为H2O时,自组装单层膜的表面水接触角下降幅度小于4°;综合TG、AFM和表面水接触的测试结果发现,用于组装的PS-SO3Na分子量介于1.5×104～3.6×104时,溶液浓度介于2.5×10-5～5×10-5mol/L时,SiO2颗粒具有较好的表面修饰效果.     

Concentration Dependence of Anti- and Pro-Oxidant Activity of Polyphenols as Evaluated with a Light-Emitting Fe2+-Egta-H2O2 System

Hydroxyl radical (^•OH) scavenging and the regeneration of Fe²⁺ may inhibit or enhance peroxidative damage induced by a Fenton system, respectively. Plant polyphenols reveal the afore-mentioned activities, and their cumulative net effect may determine anti- or pro-oxidant actions. We investigated the influence of 17 phenolics on ultra-weak photon emission (UPE) from a modified Fenton system (92.6 µmol/L Fe²⁺, 185.2 µmol/L EGTA (ethylene glycol-bis(β-aminoethyl-ether)-N,N,N′,N,-tetraacetic acid) and 2.6 mmol/L H₂O₂ pH = 7.4). A total of 8 compounds inhibited (antioxidant effect), and 5 enhanced (pro-oxidant effect) UPE at all studied concentrations (5 to 50 µmol/L). A total of 4 compounds altered their activity from pro- to antioxidant (or vice versa) along with increasing concentrations. A total of 3 the most active of those (ferulic acid, chlorogenic acid and cyanidin 3-O-glucoside; mean UPE enhancement by 63%, 5% and 445% at 5 µmol/L; mean UPE inhibition by 28%, 94% and 24% at 50 µmol/L, respectively) contained catechol or methoxyphenol structures that are associated with effective ^•OH scavenging and Fe²⁺ regeneration. Most likely, these structures can determine the bidirectional, concentration-dependent activity of some phenolics under stable in vitro conditions. This is because the concentrations of the studied compounds are close to those occurring in human fluids, and this phenomenon should be considered in the case of dietary supplementation with isolated phenolics.     

Interaction between Curcumin and β-Casein: Multi-Spectroscopic and Molecular Dynamics Simulation Methods

Effect of temperature and pH on the interaction of curcumin with β-casein was explored by fluorescence spectroscopy, ultraviolet-visible spectroscopy and molecular dynamics simulation. The spectroscopic results showed that curcumin could bind to β-casein to form a complex which was driven mainly by electrostatic interaction. The intrinsic fluorescence of β-casein was quenched by curcumin through static quenching mechanism. The binding constants of curcumin to β-casein were 6.48 × 10⁴ L/mol (298 K), 6.17 × 10⁴ L/mol (305 K) and 5.73 × 10⁴ L/mol (312 K) at pH 2.0, which was greater than that (3.98 × 10⁴ L/mol at 298 K, 3.90 × 10⁴ L/mol at 305 K and 3.41 × 10⁴ L/mol at 312 K) at pH 7.4. Molecular docking study showed that binding energy of β-casein-curcumin complex at pH 2.0 (−7.53 kcal/mol) was lower than that at pH 7.4 (−7.01 kcal/mol). The molecular dynamics simulation study showed that the binding energy (−131.07 kJ/mol) of β-casein-curcumin complex was relatively low at pH 2.0 and 298 K. α-Helix content in β-casein was decreased and random coil content was increased in the presence of curcumin. These results can promote a deep understanding of interaction between curcumin and β-casein and provide a reference for improving the bioavailability of curcumin.