Characterization of ZrO2- Al2O3mixed oxides support prepared by urea hydrolysis

The characteristics of Al₂O₃, ZrO₂ and three binary mixtures of ZrO₂-Al₂O₃ were studied by determining their BET surface areas, micropore surface area, total pore volume, adsorption-desorption isotherms, the X-ray diffractogram, surface acidity and catalytic functionality for cumene cracking. The XRD results show that the incorporation of alumina into the zirconia from 50% and beyond renders it amorphous. Furthermore, the mixed oxide containing 50% alumina and 50% zirconia had the highest BET surface area of 199.9 m²/g whilst pure zirconia had the lowest BET surface area of 37.19 m²/g. The pores for all the mixed oxides were found to be monomodal and zirconia pores were more open. The results of the acidity measurements and cumene cracking functionality indicates that whilst pure zirconia has low total acidity, the incorporation of alumina increases its acidity through a synergistic effect. This revised version was published online in June 2006 with corrections to the Cover Date.     

Zr0.5Ti0.5O2的添加对超临界裂解RP-3催化剂性能的影响

采用共沉淀法制备了Zr_0.5Ti_0.5O₂载体材料,将其掺杂在CeO₂-Al₂O₃ (CA)基催化剂中, 并对其催化活性进行了超临界裂解测试, 采用全自动吸附仪、X射线衍射(XRD)、透射电镜(TEM)、程序升温脱附(TPD)等方法对催化剂进行了表征. 实验结果表明, 催化剂能够明显降低裂解反应的温度, 600 ℃ CA基催化剂产气率是热裂解的2.8倍, 掺杂Zr_0.5Ti_0.5O₂载体材料的CA基催化剂是热裂解的4.0倍, 650 ℃时, 掺杂Zr_0.5Ti_0.5O₂载体材料的CA基催化剂热沉提高了0.55 MJ·kg^-1. BET结果表明, 掺杂Zr_0.5Ti_0.5O₂载体后催化剂出现双孔结构, 部分小孔的出现使得乙烯的选择性提高; NH₃-TPD结果表明, 掺杂Zr_0.5Ti_0.5O₂载体材料后, 催化剂强酸位的酸量增加了4.0倍,催化剂表现出更强的表面酸性和更集中的强酸酸中心密度, 有利于裂解多产烯烃.     

Surface acidity of the La2O3/Al2O3 system

Surface acidity of aluminium oxide containing 5 wt. % lanthanum oxide has been determined by IR spectroscopy. Strength of Lewis sites of the La₂O₃/Al₂O₃ system was lower than that of pure aluminium oxide. However, the presence of La₂O₃ in aluminium oxide increased the thermostability of these sites in the mixed system.     

Influence of Adding SiO2 into ZrO2 on SO2-4/ZrO2 Solid Superacid

用共沉淀法和负载法制备了一系列SO     

Valence state of Mo and surface coverage of alumina by molybdenum-oxygen species in MoOx/Al2O3

CO₂ chemisorption, BET surface area and the degree of reduction of Mo(VI) (e/Mo) have been determined in MoO_x/Al₂O₃ samples, reduced with hydrogen at temperatures between 673 and 1173 K. The free alumina surface figures calculated from the surface area and e/Mo values were identical with those obtained from direct CO₂ chemisorption measurements. This identity indicates that all of the oxygen ions of the surface molybdenum-oxygen species block the alumina surface.     

Al含量对Pt-SO2-4 /ZrO2-Al2O3固体超强酸催化

通过向SO^2-₄ /ZrO₂催化剂中同时引入适量的Pt和Al₂O₃, 制备出了具有较高催化性能和稳定性的Pt-SO^2-₄ /ZrO₂-Al₂O₃型固体超强酸催化剂. 以正戊烷异构化反应为探针, 考察了Al含量对催化剂性能的影响; 并采用X射线衍射(XRD)、比表面积测定(BET)、红外(IR)光谱、程序升温还原(TPR)、热重-差热分析(TG-DTA)和氨-程序升温脱附(NH₃-TPD)手段对催化剂进行了表征. 结果表明, Al能够提高ZrO₂的晶化温度, 抑制硫的分解, 增加催化剂的比表面积, 增强硫氧键的结合, 提高催化剂的还原性能, 增加催化剂的酸强度和酸总量. 当Al₂O₃含量(质量分数, w)为5.0%时, Pt-SO^2-₄ /ZrO₂-Al₂O₃固体超强酸催化剂的催化活性最好, 在100 h内异戊烷收率可稳定在52.0%以上, 选择性在98.2%以上.     

Surface Structure and Catalytic Performance of CuCl/SiO2-Al2O3 Catalysts for Methanol Oxidative Carbonylation

Aluminum was doped into amorphous silica gel to modify its surface structure. The obtained SiO₂-Al₂O₃ support was used to prepare the CuCl/SiO₂-Al₂O₃ catalyst by solid-state ion exchange, and the catalyst activity for liquid-phase oxidative carbonylation of methanol to dimethyl carbonate was investigated. The results showed that the prepared SiO₂-Al₂O₃ support kept the amorphous structure of the silica gel. The BET specific surface area of the silica gel was decreased to 200 m²/g, and the surface acid sites (including Brønsted acid sites) were increased. In the CuCl/SiO₂-Al₂O₃ catalyst, CuCl was not only dispersed on surface but also was ion exchanged with surface Brønsted acid sites of the SiO₂-Al₂O₃ support to form Cu⁺ species, which resulted in a decrease in BET specific surface area to 148 m²/g. These two kinds of Cu⁺ species on the catalyst surface were both active centers for the oxidative carbonylation of methanol to dimethyl carbonate. When the catalyst was prepared with Si/Al molar ratio of 5 and was calcined at 500 °C, the selectivity and space-time yield of dimethyl carbonate reached 74% and 1.27 g/(g·h), respectively.     

锂离子电池片状四氧化三钴负极的合成及改性

采用液相沉淀法结合低温固相热解法合成了锂离子电池片状Co3O4负极.通过X射线粉体衍射(XRD)、Brunauer-Emmett-Teller(BET)比表面积分析、扫描电子显微镜(SEM)及恒电流充放电等表征手段,发现该Co3O4为立方相,结晶完整且无杂质,由直径为1.5-3.0μm、厚度约为100-300 nm的不规则片状颗粒组成,比表面积约为30.5 m2·g-1;其比容量高且容量保持率好,在0.1C倍率下,首次放电容量高达1444.5 mAh·g-1,50次循环后充电容量仍大于1100.0 mAh·g-1;但在高倍率(1C)下,50次循环后充电容量保持率仅为75.3%,倍率性能一般.故采用碳纳米管(CNTs)掺杂改性,结果表明:在1C倍率下,70次循环后复合材料充电容量保持率为96.3%;在2C倍率下,50次循环后充电容量保持率仍高达97.0%,倍率性能显著提升.     

Surface electron donor properties of Dy2O3, Y2O3 and their mixed oxides with alumina catalyst

The limit of electron transfer in electron affinity from the oxide surface to the electron acceptor (EA) are reported from the adsorption of EA on Dy₂O₃, mixed oxides of Dy₂O₃ with alumina and mixed oxides of Y₂O₃ with -alumina. The extent of electron transfer is understood from magnetic measurements.     

Chemoselective Hydrazine‐mediated Transfer Hydrogenation of Nitroarenes by Co3O4 Nanoparticles Immobilized on an Al/Si‐mixed Oxide Support

Cobalt oxide nanoparticles (size 2 to 3.5 nm) were successfully impregnated on an alumina–silica (mixed oxide) support through an experimentally viable and easily reproducible protocol. The prepared material was well characterized by XRD, HR‐TEM, BET surface area, EDX and XPS analyses. Porous alumina–silica having a high surface area served as a protective heterogeneous support on which the well‐dispersed Co₃O₄ nanoparticles served as an active catalytic species for the hydrazine‐mediated transfer hydrogenation of nitroarenes. About 2 mol % of the active catalyst in ethanol at 60 °C was adequate for a successful conversion. Moreover, transfer hydrogenation of nitroarenes by the catalyst was found to take place chemoselectively in the presence of other labile functional groups such as halide, alkene, nitrile, carbonyl, and ester. This inexpensive catalyst was also able to catalyze the reaction on a gram scale reaction and found to be robust and recyclable up to eight runs.     

Preparation and characterization of LiNi0.8Co0.2O2/PANI microcomposite electrode materials under assisted ultrasonic irradiation

A preparation method for a new electrode material based on the LiNi_0.8Co_0.2O₂/polyaniline (PANI) composite is reported. This material is prepared by in situ polymerization of aniline in the presence of LiNi_0.8Co_0.2O₂ assisted by ultrasonic irradiation. The materials are characterized by XRD, TG-DTA, FTIR, XPS, SEM-EDX, AFM, nitrogen adsorption (BET surface area) and electrical conductivity measurements. PANI in the emeraldine salt form interacts with metal-oxide particles to assure good connectivity. The dc electrical conductivity measurements at room temperature indicate that conductivity values are one order of magnitude higher in the composite than in the oxide alone. This behavior determines better reversibility for Li-insertion in charge-discharge cycles compared to the pristine mixed oxide when used as electrode of lithium batteries.     

国产航空煤油裂解催化剂Pt/ZrxTixAl1-2xO2的性能

采用共沉淀法制备了一系列Zr_xTi_xAl_1-2xO₂复合氧化物载体材料,考察了其作为裂解催化剂载体对航空煤油裂解反应的影响.?采用全自动吸附仪、X射线衍射、扫描电镜/能谱仪联用、NH₃-程序升温脱附等手段对催化剂进行了表征.?结果表明,当ZrO₂：TiO₂：Al₂O₃质量比为1：1：3时催化剂具有最大的比表面积和孔容;具有最强的表面酸性和最集中的强酸中心密度,且具有良好的再生功能.?实验结果表明,载体ZrO₂：TiO₂：Al₂O₃质量比为1：1：3时催化剂上650?℃裂解产气量较热裂解提高了2.1倍,700?℃时提高1.4倍.?另外,该系列载体材料经1000?℃焙烧5?h后,所制得的催化剂几乎失去了催化活性.     

Fluoride modification of Mo/Al2O3 catalysts: Characterization of the changes induced in support and Mo phases

The characterization of fluoride-modified Mo/Al₂O₃ catalysts was performed in order to investigate on the effect that low levels of fluoridation of the alumina support (0-2.0 wt.%) cause on the support itself and on the supported Mo oxide and sulfide phases. Fluoride-modified Al₂O₃ supports and Mo/Al₂O₃ catalysts where characterized by nitrogen physisorption, scanning electronic microscopy (SEM-EDX), isoelectric point (IEP), Fourier transform infrared spectroscopy (FT-IR), infrared spectroscopy of adsorbed CO₂ (IR-CO₂), and temperature programmed reduction (TPR). The dispersion of the sulfided catalysts was estimated by dynamic NO chemisorption. The results indicate that the different hydroxyl types present on the alumina surface react to a different extent with fluoride and that it is the most basic hydroxyl groups that are titrated first.The consumption of the alumina OH by F⁻, inhibits, during the deposition of Mo, the formation of tetrahedral molybdenum oxide species in strong interaction with the support, leading to an increased number of polymeric octahedral Mo surface species. The NO adsorption results put in evidence a drop in the dispersion of the MoS₂ phase present in the sulfided samples.     

二氧化钛柱撑层状氧化锰微孔材料的合成及表征

Na型层状锰氧化物于0.1 mol/L HCl 溶液中离子交换制得前驱体H型层状锰氧化物. H型层状锰氧化物在十二胺乙醇溶液中反应得到层间距为2.62 nm的中间产物——十二胺插入的层状锰氧化物, 该中间产物在异丙醇钛和乙醇的混合溶液中溶剂热处理得到层间距为1.24 nm的钛酸柱撑层状锰氧化物. 在300 ℃条件下经2 h焙烧得到二氧化钛铸型氧化锰微孔材料. 应用XRD, DSC-TGA, SEM, TEM, IR, 氮气吸附实验及元素分析进行了不同阶段所得试样的分析表征. 结果表明十二胺分子在锰氧层间的最大插入量为2.2 mmol/g, 异丙醇钛分子的置换插入生成了组成为Mn_7.00Ti_1.74O_23.3(C₁₂H₂₅NH₂)_0.52•1.93H₂O的铸型层状锰氧化物. 300 ℃焙烧处理所得二氧化钛铸型氧化锰微孔材料的比表面积为140 m²/g.     

纳米复合固体超强酸SO42-/CoFe2O4的制备和表征

采用纳米化学制备技术合成了新型的纳米复合固体超强酸催化剂ＳＯ４＾２－／ＣｏＦｅ２Ｏ４。用ＸＲＤ、ＴＥＭ、ＸＰＳ、红外光谱和比表面测定等技术研究了该催化剂的结构形态,结果表明：所研制的ＳＯ４＾２－／ＣｏＦｅ２Ｏ４２催化剂为晶态纳米粒子（〈５０ｎｍ）,比表面积很大（１５７ｍ＾２．ｇ＾－１）,ＳＯ４＾２－与氧化物的金属离子呈无机齿螯合状配位化合物的结合形式。以乙酸乙酯合成为模型反应考究了该催化剂的催化活     

Characterization of La-promoted Ni/Al2O3 catalysts for hydrogen production from glycerol dry reforming

In the current paper, dry (CO₂)-reforming of glycerol, a new reforming route, was carried out over alumina (Al₂O₃)-supported, non-promoted and lanthanum-promoted nickel (Ni) catalysts. Both sets of catalysts were synthesized via a wet co-impregnation procedure. Physicochemical characterization of the catalysts showed that the promoted catalyst possessed smaller metal crystallite size, hence higher metal dispersion compared to the virgin Ni/Al₂O₃ catalyst. This was also corroborated by the surface images captured by the FESEM analysis. From temperature-programmed calcination analysis, the derivative weight profiles revealed two peaks, which represent a water elimination peak at a temperature range of 373 to 473 K followed by nickel nitrate decomposition from 473 to 573 K. In addition, BET surface area measurements gave 85.0 m²·g⁻¹ for the non-promoted Ni catalyst, whilst the promoted catalysts showed an average of 1% to 6% improvement depending on the La loadings. Significantly, reaction studies at 873 K showed that glycerol dry reforming successfully produced H₂. The 2%La-Ni/Al₂O₃ catalyst, which possessed the largest BET surface area, gave an optimum H₂ generation (9.70%) at a glycerol conversion of 24.5%.     

Spectroscopic characterization of some iron-containing pillared clays

Bentonites, when pillared with Al₂O₃-oxide clusters, can generate materials with BET surface area in the 290–310 m² g⁻¹ range having high cracking activity for gas oil conversion. The high coke make tendency of these catalysts has been attributed to their strong Lewis type acidity.Mössbauer and X-ray photoelectron spectroscopy have shown that iron in pillared clays can be found on the clay platelets, between the clay silicate layers or in the clay octahedral layer in substitution for Al. On heating, iron migration occurs. When iron is found near the pillars it can easily catalyze secondary cracking reactions and greatly enhances the already high coke make generation observed during gas oil conversion.     

Influence of the carrier characteristics on the catalytic activity of supported TiCl4/Al(C2H5)2Cl Ziegler catalyst in the ethylene polymerization

The effect of the carrier characteristics, such as specific surface area and acidity, on the activity of supported Ziegler catalyst in the ethylene polymerization has been investigated. Silica-gel and silica-alumina, containing various quantities of alumina (5, 13 and 25 wt-%) and also modified by deposition of Zn metal, wer used as carriers. The different carriers give rise to catalysts with different activities after deposition of TiCl₄ and activated with Al(C₂H₅)₂Cl. The activity in ethylene polymerization is controlled firstly by the chemical composition of the carriers and secondly by its specific surface area. The silica-aluminas show higher acidities than silica-gel and deposition of Zn is accompanied by considerable changes in the carriers, especially increasing their acidity and decreasing the specific surface areas. The increase of the carrier acidity gives rise to an increase in the polymerization activitity and in the polymer molecular weights. Coordinately unsaturated titanium ions, on the surface of the catalysts containing Zn metal, are detected by ESR, showing a paramagnetic signal similar to those produced by TiCl₃ crystals.     

Catalytic Combustion of Ethyl Acetate over Al2O3- Ce0.5Zr0.5O2 Supported Metal Oxide Catalysts

The catalysts for the combustion of ethyl acetate were prepared using Fe, Co, Cu, Cr, and Mn metal oxide as active components supported on Al₂O₃-Ce_0.5Zr_0.5O₂ mixed oxides and characterized by X-ray diffraction (XRD), temperature programmed reduction (TPR), oxygen storage capacity measurement, BET surface area, XPS measurement, and activity test. According to the results of characterization, it was found that Cu/Al₂O₃-Ce_0.5Zr_0.5O₂ (1:2, mass ratio) and Mn/Al₂O₃-Ce_0.5Zr_0.5O₂ (1:2) catalysts presented excellent activity for the catalytic combustion of ethyl acetate, because of the more reducible species and high reducibility of the catalysts. For ethyl acetate oxidation, more than 99% conversion was achieved at 245 °C over catalysts Cu/Al₂O₃-Ce_0.5Zr_0.5O₂ (1:2) and Mn/Al₂O₃-Ce_0.5Zr_0.5O₂ (1:2, mass ratio), indicating that the catalysts had great potential for wide use.     

Taguchi Optimization for Combustion Synthesis of Aluminum Oxide Nano-particles

Nano-structured aluminum oxide powders were prepared by a combustion synthesis method utilizing serine as a new fuel. The product was sonicated to obtain nano powders. A Taguchi L-4 statistical design of combustion synthesis was utilized to optimize the production of γ-alumina powder. The product was characterized by XRD, BET, SEM, EDX and LLS. Nano crystalline γ-alumina with crystal sizes between 4.26 and 5.47 nm and α-Al2O3 powders with crystal sizes 24.51 and 28.62 nm were obtained by the combustion synthesis. The specific surface area was measured by a BET method to be 75.21 m2/g. The average particle size after sonication of product, observed by LLS, was 79.32 nm.