超软X射线流气式正比计数管

介绍了一种用于测量183～933eV超软X射线的圆柱形、侧窗式、流气式正比计数管,工作气体是0.11MPa的P-10气体或氦气-丙烷混合气体。计数管内径为φ25mm,直径为φ0.3mm的入射窗是由厚度80～90μgcm~2聚乙烯甲醛制成的。该计数管的特点:(1)薄窗,对软X射线透过率高。(2)流气式,工作寿命长。(3)能量分辨率好。(4)计数率高(1×10~(14)个/s)。(5)可测能区宽(0.183～10keV)。(6)可以方便更换窗膜材料、厚度及窗口直径。近几年来该计数管已经为高强度低能X光源提供较好监测。     

MC模拟分析透射式微型X射线管目标靶厚度对输出谱的影响

透射式微型X射线管是能量色散X射线荧光分析中的主要激发源,在能量色散X射线荧光分析中希望得到谱分布较为单一的X射线管输出谱。采用MC方法,研究了透射式微型X射线管在不同目标靶厚度的情况下输出谱的特征,通过低谱段(<5 keV)和高能谱段(5~50 keV)的分析比较,高能谱段计数随厚度加大先增加而后减小,低能谱段计数则随厚度增加减小,增加目标靶厚度可以有效抑制低能谱段。在入射电子能量为50 keV和目标靶为4 Ag的条件下,X射线管输出能谱具有较高的高能谱段注量,同时有效压制低能谱段注量,适合能量色散X射线荧光分析中使用。     

氢分子离子与氮分子碰撞过程的实验研究

本文讨论了用离子存储技术研究低能(eV量级)氢分子离子与氮分子碰撞的过程.得到质子交换率常数K_(pt)=5.23×10~(-9)cm~3/sec和电荷交换率常数k_(ct)=0.45×10~(-9)cm~3/sec     

X射线绝对测量

在5—25keV单能刻度用X射线发生器上,用充氩密封式正比计数管直接测量了X射线量子效率为0.877±0.011—0.107±0.002,推算出X射线发生器绝对产额为(1.40±0.03)×10~(10)—(9.20±0.39)×10~8/s。     

低能离子注入形成氮化硅薄膜特性的研究

低能离子束与表面相互作用主要呈现溅射、注入等现象。本文研究了在1.35keVN₂⁺离子注入形成氮化硅的特性,并研究了注入和溅射的并存过程。在高剂量、低能(<10keV)注入的情况下,提出了有效剂量的概念,并建立了刻蚀速率、射程与有效注入剂量的关系。还用俄歇电子能谱(AES)、X射线光电子能谱(XPS)、透射电子显微镜(TEM)、背散射分析(RBS)测定了薄膜的有关特性。 关键词：     

土壤重金属铅元素的X射线荧光光谱测量分析

在实验室条件下,利用NITON XLt793型便携式X射线荧光光谱重金属分析仪测量并分析土壤中铅元素的X射线荧光光谱特性。分别以铅的L_α(10.55 keV)和L_β(12.61 keV)特征谱线作为分析线,分析了不同基体元素对分析线的影响;测定在不同铅浓度下的特征谱线强度变化。结果表明铅的质量分数在10×10-6～1 800×10-6范围内,元素的光谱强度与浓度之间呈现较好的线性关系;建立了铅元素的定标曲线,并计算得到铅的检出限为7.89×10-6。     

微通道板2.0～5.5 keV X射线透过率标定

 在北京同步辐射3B3中能X射线束线2.0~5.5 keV能段对微通道板(MCP)透过率进行了测量标定。实验表明,MCP在2.0 keV的低能段处和5.5 keV的高能段处的透过率较高,而中段较低。对MCP透射和X光在MCP毛细导管列阵中的全反射两种机制进行了物理建模,分别计算验证。结果发现:X光在毛细导管内掠入射会产生全反射,且能段越低反射率越高;MCP透过率特性正是MCP特殊的结构和材料造成的,为透射和反射两种机制共同贡献的结果,低能端主要来自X光在毛细导管中的全反射贡献,高能端主要来自透射贡献。     

射线探测用碲锌镉晶体及其器件研究

采用改进的布里奇曼(B ridgm an)方法进行锌组分为0.15碲锌镉(Cd0.85Zn0.15Te)晶体的生长。通过严格控制晶体生长过程中Cd的蒸气分压,使得所生长的碲锌镉晶体在结晶质量方面达到了较好的水平。对其性能进行测试,红外透射比T>60%、沉积相密度<1×104/cm2、位错腐蚀坑密度DEPD<6×104/cm2、X射线衍射双晶回摆曲线半峰全宽FWHM<20 arcsec、电阻率ρ>1010Ω.cm。利用所生长的晶体初步制作了平面型单元碲锌镉射线探测器,所用晶体的尺寸为5 mm×5 mm×2.5 mm,制成的探测器在室温下对125I和241Am放射源进行了探测测量。对125I放射源,探测出了强度为74.5%的27.5 keV的γ射线特征峰,不能仔细分辨出强度为39.8%的27.2 keV的γ射线特征结构;对241Am放射源,探测出了59.5 keV的γ射线特征峰,分辨率优于6 keV,半峰全宽FWHM<10%,同时还能检测出Te、Cd的X射线逃逸的混合峰以及241Am低能Te-K系、Np-L系的两个X射线特征峰。     

100keV质子与低高能质子在绝缘微孔中输运特性的对比分析

为研究中能区带电粒子在绝缘微孔中传输的物理图像,利用MATLAB程序和蒙特卡罗方法建立理论模型,得到入射能量为10 keV,100 keV和1 MeV的质子,以-1?倾斜角入射到微孔后,出射粒子角分布、沉积电荷斑分布,以及粒子在微孔内的运动轨迹等传输特性.研究结果表明,在10 keV的低能区,微孔内壁沉积电荷的导向效应是主要的传输机制.在1 MeV的高能区,进入表面以下多次随机非弹性碰撞是主要的输运机制.在100 keV的中能区,无电荷斑时,主要是以进入表面以下的随机二体碰撞为传输机制;在电荷斑累积过程中,增强的库仑排斥力逐渐抑制入射质子在微孔内壁表面发生电子俘获;当达到充放电平衡后,主要传输机制为电荷斑辅助的近表面镜面散射行为.这一特性加深了对中能区质子在微孔中输运行为的认识,有助于对百keV质子微束的控制和应用.     

邻苯二钾酸氢铊晶体积分衍射效率的标定

 以北京同步辐射实验室4B7中能束线为光源，在2.1~6.0 keV的范围内对邻苯二钾酸氢铊(TlAP)平面晶体一、二 、三级衍射的积分衍射效率进行了精确的实验标定。标定结果表明：TlAP晶体有较高的峰值衍射率； 其一级衍射的积分衍射效率向低能端有增加的趋势，而在2.6~5.4 keV的范围内大约为1.53×10^-4 rad；随着衍射级次的提高，衍射效率逐渐减小，二级衍射的积分衍射效率约为一级衍射效率的1/4，三级衍射结果比一级衍射下降一个量级。实验所标定的TlAP晶体可用于平晶谱仪对激光等离子体X射线光谱的定量分析。     

Hybrid Wavelength and Code Division Multiple Access in Optical Networks

A review of schemes for multiple access in fiber optic networks shows that a hybrid of wavelength and code division multiple access (WCDMA) combines the best features of both. In particular, the hybrid scheme retains the large information carrying capacity of wavelength division multiple access (WDMA) and flexibility of code division multiple access (CDMA). In this paper WDMA, optical CDMA (OCDMA), and WCDMA networks are discussed. In OCDMA networks, concept of incoherent and coherent coding including inverse decoding and matched filter is introduced. The delay performance of both WDMA and WCDMA networks, under the simple suboptimum access protocols based on cyclic search, is computed. It has been shown quantitatively that tuning delay significantly affects the delay performance of both WDMA and WCDMA networks. Futhermore, delay performance of WCDMA networks is always better than the WDMA networks for the same tuning delay, load, and number of users.     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Research on beamforming method for dual-line array with space mismatch between the two line arrays

The performance of port/starboard discrimination of dual-line array will be seriously degraded when the space between the two line arrays of the dual-line array is mismatched. The directivity function of the delay-sum and delay-subtract beamforming is deduced and the port/starboard discrimination of the delay-sum and delay-subtract beamforming is also studied both under the ideal status and the status under which the space between the two line arrays of the dual-line array is mismatched. Analysis results show the delay-subtract beamforming has better performance of port/starboard discrimination. At last, the sea trial results demonstrate the theoretical results.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Retrieval of ultraviolet skylight radiances and O3 slant column densities from balloon-borne limb spectrometer

With a novel light-weight and absolutely calibrated ultraviolet （UV） spectrometer, UV skylight radiances and O3 slant column densities are measured by balloon-borne limb measurements in Xinjiang area, China. UV skylight radiances measured at the height of 31 km are compared with the results from Modtran in the wavelength range from 290 to 420 nm. O3 slant column densities are derived from radiance spectra in the Huggins bands （320 - 335 nm） using differential optical absorption spectroscopy method. And the parameter exhibits a good correlation with the same value simulated by radiative transfer model （Tracy）. The O3 profile simultaneously measured by an O3 sonde is used as input in Tracy calculations. The O3 sonde is launched on the same balloon.     

Design optimization of highly sensitive LSPR enhanced surface plasmon resonance biosensors with nanoholes

For breaking through the sensitivity limitation of conventional surface plasmon resonance (SPR) biosensors, novel highly sensitive SPR biosensors with Au nanoparticles and nanogratings enhancement have been proposed recently.But in practice, these structures have obvious disadvantages.In this study, a nanohole based sensitivity enhancement SPR biosensor is proposed and the influence of different structural parameters on the performance is investigated by using rigorous coupled wave analysis (RCWA).Electromagnetic field distributions around the nanohole are also given out to directly explain the performance difference for various structural parameters.The results indicate that significant sensitivity increase is associated with localized surface plasmons (LSPs) excitation mediated by nanoholes.Except to outcome the weakness of other LSP based biosensors, larger resonance angle shift, reflectance amplitude, and sharper SPR curves' width are obtained simultaneously under optimized structural parameters.     

Polymer gratings based on photopolymerization for low-order distributed feedback polymer lasers

Novel polymer distributed feedback(DFB)gratings are fabricated based on photopolymerization to reduce lasing threshold of polymer lasers.A photopolymer formulation sensitive to 355-nm ultraviolet(UV)light is proposed for the fabrication of polymer gratings and it can be used to form polymer films by spin-coating process.A very low surface-relief depth ranging from 12.5 to about 1.0 nm has been demonstrated with a refractive-index modulation of about 0.012.The experimental results indicate that such polymer gratings have promising potentials for the fabrication of low-order DFB organic semiconductor lasers.     

A novel methodology for photometric compensation of projection display on patterned screen

We propose a novel methodology based on the projector-camera (ProCam) system to address the photometric compensation issue for the projection display on the patterned screen.The patterned screen is treated as the combination of a perfect white screen and a color modulator.The perfect white screen is used to automatically and accurately characterize the ProCam system offline using the polynomial model,and the parameters of the color modulator can be efficiently recovered by employing only two gray images based on the linear reflectance model.The experimental results show that the color artifacts of the display image can be greatly improved with this methodology,which demonstrates its feasibility and validity in the photometric compensation.