Adsorption kinetics of deamidated antibody variants on macroporous and dextran-grafted cation exchangers. III. Microscopic studies

The kinetics of single and multicomponent adsorption of deamidated monoclonal antibody (mAb) charge variants is investigated using confocal laser scanning microscopy for two commercial cation exchangers, one with an open macroporous structure--UNOsphere S--and the other with charged dextran grafts--Capto S. Markedly different intraparticle concentration profiles are obtained, being very sharp for UNOsphere S, indicating pore diffusion control, but much more diffuse for Capto S, consistent with a solid or surface diffusion mechanism. For single-component adsorption, the mAb effective pore diffusivities for UNOsphere S are approximately D(e)=4.5×10(-8) and 8.3×10(-8) cm(2)/s at pH 5 and 7.5, respectively, while effective solid diffusivities for Capto S are D(s)=0.98×10(-9) and 5.0×10(-9) cm(2)/s at pH 5 and 7.5, respectively. Two-component adsorption at pH 7.5, where the deamidated variants are bound selectively also showed markedly different profiles for the two matrices. UNOsphere S showed distinct adsorption zones within the particles indicating that multicomponent transport occurs with continuous displacement of the more deamidated variant by the less deamidated one. Capto S, however, showed no spatial resolution of the variants within the particle during co-adsorption and very slow mass transfer during sequential adsorption suggesting that protein counter-diffusion is severely hindered in this material.     

Adsorption of deamidated antibody variants on macroporous and dextran-grafted cation exchangers: II. Adsorption kinetics

Single and multicomponent batch adsorption kinetics were obtained for deamidated mAb variants on two commercial cation exchangers, one with an open macroporous structure--UNOsphere S--and the other with charged dextran grafts--Capto S. The adsorption kinetics for the macroporous matrix was found to be controlled largely by pore diffusion. The effective diffusivity estimated from single component data was a fraction of the mAb free solution diffusivity, and its value could be used to accurately predict the adsorption kinetics for two- and three-component systems. In this case, when two or more variants were adsorbed simultaneously, both experimental and predicted results showed a temporary overshoot of the amount adsorbed above the equilibrium value for the more deamidated variant followed by a gradual approach to equilibrium. Adsorption rates on the dextran grafted material were much faster than those observed for the macroporous matrix for both single component and simultaneous adsorption cases. In this case, no significant overshoot was observed for the more deamidated forms. The Capto S adsorption kinetics could be described well by a diffusion model with an adsorbed phase driving force for single component adsorption and for the simultaneous adsorption of multiple variants. However, this model failed to predict the adsorption kinetics when more deamidated forms pre-adsorbed on the resin were displaced by less deamidated ones. In this case, the kinetics of the displacement process was much slower indicating that the pre-adsorbed components severely hindered transport of the more strongly bound variants. Overall, the results indicate that despite the lower capacity, the macroporous resin may be more efficient in process applications where displacement of one variant by another takes place as a result of the faster and more predictable kinetics.     

Adsorption equilibrium of fructosyltransferase on a weak anion-exchange resin

The adsorption equilibrium of a glycoprotein, fructosyltransferase from Aureobasidium pullulans, on an anion-exchange resin, Sepabeads FP-DA activated with 0.1M NaOH, was investigated. The adsorption isotherms were determined at 20 degrees C in a phosphate-citrate buffer with pH 6.0 using the static method. Sodium chloride was used to adjust the ionic strength in the range from 0.0215 to 0.1215 mol dm(-3) which provided conditions varying from a weak effect of salt concentration on protein binding to its strong suppression. The equilibrium data were very well fitted by means of the steric mass-action model when the ion-exchange capacity of 290 mmol dm(-3) was obtained from independent frontal column experiments. The model fit provided the protein characteristic charge equal to 1.9, equilibrium constant 0.326, and steric factor 1.095 x 10(5).     

High-performance liquid chromatography of sialooligosaccharides and gangliosides

Glycans were cleaved from gangliosides and separated by high-performance liquid chromatography (HPLC). The columns were packed with bonded stationary phases made of microparticulate, macroporous silica with serotonin, phenylpropanolamine or tryptamine as the biogenic amine ligate. The ganglioside oligosaccharides were eluted in the order of increasing number of sialic acid residues in the molecule and their retention decreased with the ionic strength of the mobile phase. Best selectivity was obtained in the pH range from 3.0 to 4.0. The two major sialic acids, N-acetylneuraminic and N-glycolylneuraminic acids, were separated by lectin affinity chromatography using an HPLC column packed with silica-bound wheat germ agglutinin and 10 mM phosphate buffer, pH 4.0, as the eluent. Throughout this study, isocratic elution was used and the column effluent was monitored at 195 nm.     

Adsorption kinetics of zinc in multicomponent ionic systems

Using commercial activated carbon as an adsorbent, the kinetics of adsorption of zinc from multicomponent ionic systems having cadmium and mercury has been studied and reported. The variables investigated have been the chemical nature, ionic strength, and pH of the adsorptive (Zn2+) solution. The adsorption of Zn2+ is speeded up by the presence of Cd2+ and Hg2+ ions provided that the concentration of these two ions is high as compared to the concentration of Zn2+. When the ionic strength of the solution in relative terms is high (i.e., > 3 x 10(-4) M), however, the adsorption of Zn2+ decelerates. Also, the adsorption process is greatly accelerated at pH 12, whereas at pH 2 it does not occur at all.     

三维有序大孔尖晶石型Li1.6Mn1.6O4的制备及锂离子筛吸附特性

用LiNO3、Mn(Ac)2•4H2O和柠檬酸的混合溶液填充聚甲基丙烯酸甲酯胶体晶体模板, 在空气中氧化焙烧, 制备出三维有序大孔尖晶石型锂锰氧化物Li1.6Mn1.6O4. 前驱体经过0.1 mol/L盐酸脱锂后获得相应的三维有序大孔锂离子筛, 其大孔直径和孔壁厚度分别为240 nm和50 nm左右. XRD测试结果表明, Li1.6Mn1.6O4、锂离子筛和吸锂后的样品均保持尖晶石结构. 三维有序大孔材料呈现彼此连通的孔道空间, 缩短了Li+的平衡吸附时间, 前驱体脱锂率在80 ℃时达到95%, 而锰的溶损率在低于60 ℃时小于2.5%. 溶液温度对Li+的交换能力影响很大, 升高温度, Li+与H+的可逆交换程度增大, Li+的最大吸附容量为56.7 mg/g, 但处于锰16d八面体缺陷位置的氢难于被交换. pH滴定和分配系数(Kd)分析表明, 该固体酸在Li+, Na+和K+共存溶液中对Li+的吸附具有较高的选择性.     

Usage of nonporous polymeric particles for reversed-phase high-performance liquid chromatography of oxidized and deamidated forms of recombinant human growth hormone

In this work, a C(18) reversed-phase column with nonporous polymeric 2.5- micro m particles is utilized to initially test the analysis of oxidized and deamidated human growth hormone (hGH). Phosphate buffer (pH 7.5) with 24% 1-propanol was used for elution. This quick method (analysis time is 20 min) gave a selectivity, as judged by the number of detected peaks, and resolution of hGH variants that is better than many methods in which porous silica particle columns are used. Only mixtures of oxidized and deamidated hGH are analyzed, and no characterization of the peaks is performed. The results indicate that C(18) nonporous polymeric column material is a promising alternative for the chromatographic separation of several hGH variants.     

Smooth model surfaces from lignin derivatives. II. Adsorption of polyelectrolytes and PECs monitored by QCM-D

For the first time to the knowledge of the authors, well-defined and stable lignin model surfaces have been utilized as substrates in polyelectrolyte adsorption studies. The adsorption of polyallylamine (PAH), poly(acrylic acid) (PAA), and polyelectrolyte complexes (PECs) was monitored using quartz crystal microgravimetry with dissipation (QCM-D). The PECs were prepared by mixing PAH and PAA at different ratios and sequences, creating both cationic and anionic PECs with different charge levels. The adsorption experiments were performed in 1 and 10 mM sodium chloride solutions at pH 5 and 7.5. The highest adsorption of PAH and cationic PECs was found at pH 7.5, where the slightly negatively charged nature of the lignin substrate is more pronounced, governing electrostatic attraction of oppositely charged polymeric substances. An increase in the adsorption was further found when the electrolyte concentration was increased. In comparison, both PAA and the anionic PEC showed remarkably high adsorption to the lignin model film. The adsorption of PAA was further studied on silica and was found to be relatively low even at high electrolyte concentrations. This indicated that the high PAA adsorption on the lignin films was not induced by a decreased solubility of the anionic polyelectrolyte. The high levels of adsorption on lignin model surfaces found both for PAA and the anionic PAA-PAH polyelectrolyte complex points to the presence of strong nonionic interactions in these systems.     

Adsorption of cationic lipid bilayer onto flat silicon wafers: effect of ion nature and concentration

The effect of monovalent salt nature and concentration over a range of low ionic strengths (0-10 mM LiCl, NaCl, KCl, or CsCl) and at two different pH values (6.3 and 10.0) on adsorption of dioctadecyldimethylammonium bromide (DODAB) bilayer fragments (BF) onto flat SiO(2) surfaces was systematically evaluated by means of in situ ellipsometry. High-affinity adsorption isotherms fitted by the Langmuir model indicated that adsorption maxima were consistent with bilayer deposition only around 10 mM monovalent salt at both pH values. In pure water, the mean thickness of the DODAB adsorbed layer was close to zero with bilayer deposition taking place only around 10 mM ionic strength. In the presence of 10 mM CsCl or LiCl, the highest and the lowest affinity constants for DODAB adsorption onto SiO(2) were, respectively, obtained consistently with the expected facility of cation exchange at the surface required for DODAB adsorption. The cation more tightly bound to the solid surface should be Li(+), which would present the largest resistance to displacement by the DODAB cation, whereas the less tightly bound cation should be Cs(+) due to its largest ionic radius and lowest charge density. In other words, DODAB adsorption proceeds in accordance with charge density on the solid surface, which depends on the nature and concentration of bound counterions as well as DODAB cation ability to displace them. AFM images show a very smooth DODAB film adsorbed onto the surface in situ with a large frequency of BF auto-association from their edges. The present results for flat surfaces entirely agree with previous data from our group for DODAB adsorption onto silica particles.     

静电力驱动蛋白质在疏水蛋白表面的吸附

疏水蛋白是丝状真菌产生的一种外泌蛋白质, 它们可以在不同表面形成双亲性蛋白膜. 疏水蛋白也是一种优良的蛋白质固定化基质, 然而蛋白质在疏水蛋白表面吸附的驱动机制却是未知的. 本文系统研究了不同pH和离子浓度下蛋白质在疏水蛋白表面的吸附. 首先, 用石英晶体微天平技术研究了不同pH和离子浓度下, Ⅰ型疏水蛋白HGFI和Ⅱ型疏水蛋白HFBI在聚苯乙烯表面的吸附. 结果发现, pH和离子强度对HGFI在聚苯乙烯表面的吸附影响较大, 对HFBI的吸附影响与HGFI相比则较小; HGFI在聚苯乙烯表面主要形成的是弹性膜, 而HFBI在聚苯乙烯表面主要形成的是刚性膜. 随后又研究了不同pH和离子浓度下牛血清白蛋白(BSA)和亲和素(Avidin)在HGFI和HFB上吸附, 结果表明, pH和离子强度对BSA和Avidin在HGFI和HFB上吸附有显著影响, 说明BSA和Avidin在两种疏水蛋白上吸附的主要驱动力为静电力. 本文研究结果为实现疏水蛋白表面可控地固定蛋白质提供了理论指导.     

Capillary electrophoresis analysis of gentamicin sulphate with UV detection after pre-capillary derivatization with 1,2-phthalic dicarboxaldehyde and mercaptoacetic acid

A selective, sensitive, and rapid pre-capillary derivatization method for determination of the multicomponent aminoglycoside antibiotic gentamicin is described. The derivatization reagents 1,2-phthalic dicarboxaldehyde and mercaptoacetic acid were used and the thioisoindole derivative was UV detected at 330 nm. A central composite experimental design was performed to optimize selectivity and derivatization conditions. Baseline separation of gentamicin C1, C1a, C2, C2a, C2b, sisomicin and several minor components was achieved with a background electrolyte containing 30 mM sodium tetraborate, 7.5 mM beta-cyclodextrin and 12.5% (v/v) methanol at pH 10. Quantitative analysis was performed and illustrated the potential use of capillary electrophoresis for the identification and quantitation of gentamicin as an alternative to methods prescribed in the United States Pharmacopeia and European Pharmacopoeia.     

Fabrication of macroporous polystyrene/graphene oxide composite monolith and its adsorption property for tetracycline

Macroporous polystyrene microsphere/graphene oxide(PS/GO) composite monolith was first prepared using Pickering emulsion droplets as the soft template. The Pickering emulsion was stabilized by PS/GO composite particles in-situ formed in an acidic water phase. With the evaporation of water and the oil phase(octane), the Pickering emulsion droplets agglomerated and combined with each other, forming a three-dimensional macroporous PS/GO composite matrix with excellent mechanical strength. The size of the macrospores ranged from 4 mm to 20 mm. The macroporous PS/GO composite monolith exhibited high adsorption capacity for tetracycline(TC) in an aqueous solution at p H 4–6. The maximum adsorption capacity reached 197.9 mg g 1at p H 6. The adsorption behaviour of TC fitted well with the Langmuir model and pseudo-second-order kinetic model. This work offers a simple and efficient approach to fabricate macroporous GO-based monolith with high strength and adsorption ability for organic pollutants.     

Study of the retention behavior of small polar molecules on different types of stationary phases used in hydrophilic interaction liquid chromatography

The retention behavior of a large group of analytes (35) with varied properties (pK_a and logP) was studied on eight hydrophilic interaction LC columns with different surfaces, stationary phase chemistries, and types of particles. The acetonitrile content (5–95%), buffer concentration (0.5–200 mM), and pH of the mobile phase (3.8 and 6.8) were evaluated for their effects on the retention behavior. The type of stationary phase had a significant impact on the selectivity and retention time of the tested analytes. Completely different selectivity was observed on the aminopropyl stationary phase. In this study, the influence of the buffer concentration was similar for all tested columns, except for the aminopropyl stationary phase. Increasing the buffer concentration led to decreased retention times for the basic compounds and increased retention times for the acidic compounds, while the inverse behavior was observed on the aminopropyl stationary phase. The selectivity of the individual stationary phases was evaluated at pH 3.8 and 6.8. Much lower selectivity differences between the stationary phases were observed at pH 6.8 than pH 3.8. Bare silica stationary phases were used in the comparison of the particles (fused‐core and fully porous particles of 3 and 1.7 μm) and the columns provided by different manufacturers.     

Adsorption of organic matter at mineral/water interfaces. 2. Outer-sphere adsorption of maleate and implications for dissolution processes

The effects of the adsorption of a simple dicarboxylate low molecular weight organic anion, maleate, on the dissolution of a model aluminum oxide, corundum (alpha-Al2O3), have been examined over a range of different maleate concentrations (0.125-5.0 mM) and pH conditions (2-10). In situ attenuated total reflectance Fourier transform infrared (ATR-FTIR) spectroscopic measurements indicate that maleate binds predominantly as an outer-sphere, fully deprotonated complex ([triple bond]AlOH2+ -Mal2-) at the corundum surface over the entire range of maleate concentrations and pH conditions investigated. In accordance with the ATR-FTIR findings, macroscopic adsorption data can be modeled as a function of maleate concentration and pH using an extended constant capacitance approach and a single [triple bond]AlOH2+ -Mal2- species. Outer-sphere adsorption of maleate is found to significantly reduce the protolytic dissolution rate of corundum under acidic conditions (pH < 5). A likely mechanism involves steric protection of dissolution-active surface sites, whereby strong outer-sphere interactions with maleate hinder attack on those surface sites by dissolution-promoting species.     

Effect of surface packing density of interfacially adsorbed monoclonal antibody on the binding of hormonal antigen human chorionic gonadotrophin

Interfacial adsorption of a mouse monoclonal antibody (type IgG1, anti-beta-hCG) at the hydrophilic silicon oxide/water interface has been studied by spectroscopic ellipsometry and neutron reflection, followed by assessment of binding of a hormonal antigen, human chorionic gonadotrophin (hCG), onto the adsorbed antibody molecules. The amount of adsorption reached a maximum around the isoelectric pH (IP) of 6 for the antibody; this pH-dependent pattern could be altered by increasing salt concentration, a trend also observed for other proteins. Neutron reflection revealed the formation of a 40 A uniform layer from the adsorbed antibody, indicating a flat-on orientation. The subsequent hCG binding showed that the molar ratio of hCG bound to antibody at the interface was as high as 0.7 at low surface coverage of antibody and decreased with increasing surface antibody concentration. The results point to an increasing extent of steric hindrance to hCG access with increasing packing density of antibody molecules on the surface. Comparison with previously published crystal structure studies suggests twisting of the variable region to allow access of the antigen. The binding of hCG was also found to be pH-dependent with its maximum around the IP, if the ionic strength of the solution was low (20 mM). However, if the ionic strength was increased to 200 mM, then hCG binding was influenced by a combination of steric hindrance and electrostatic interaction between the antigen and the surface. These results are highly relevant to the improvement of the performance of biotechnologies such as fertility test pads and biosensors based on antibody immobilization.     

X-5大孔树脂吸附熊果酸的动力学与热力学特性研究

研究了熊果酸在X-5树脂上吸附的动力学和热力学特性,从物理化学的角度探讨了树脂吸附天然产物的机理。动力学结果表明,在pH=6.36时,熊果酸在X-5树脂上吸附量最大,吸附量为0.1016mmol/g。热力学结果表明,不同温度下熊果酸在X-5树脂上的等温吸附符合Langmuir方程和Freundlich方程,吸附热焓变?Hm=58.77kJ/mol,熵变?Sm=0.23kJ/mol·K,吉布斯自由能?Gm随温度升高向负方向增加。以上热力学参数表明,熊果酸在X-5树脂上的吸附属于自发的物理吸附过程,且在X-5大孔树脂吸附熊果酸过程中,液固界面间增加了随机性吸附。     

Adsorption effects in rejection of macromolecules by ultrafiltration membranes

Rejection of adsorbing solutes by ultrafiltration membranes is not adequately described by the steric rejection theory [3]. Solute adsorption (fouling) changes the shape of the rejection curve. Typically, the measured curves are steeper than the theoretical curve. The shape of the curve can be predicted qualitatively from simple theoretical considerations. For adsorbing solutes, single-solute and multiple-solute ultrafiltration experiments give different results. Relative thickness of adsorbed solute layer in a membrane pore was found to depend on (1) solute size, (2) solute hydrophobicity, (3) pH and ionic strength for a protein solute, (4) solute concentration, and (5) time of adsorption. Large differences observed between water fluxes and fluxes of very dilute polymer solutions through the same membrane are also interpreted in terms of solute adsorption.     

Factors affecting the stability of O/W emulsion in BSA solution: stabilization by electrically neutral protein at high ionic strength

Bovine serum albumin (BSA) was used as an emulsifier to disperse corn oil in aqueous media with various protein concentration, pH, and ionic strength. Quantitative estimation was made on the homogenizing activity of BSA and dispersion stability of oil particles by measuring particle size, turbidity, and creaming rate. Dispersion stability strongly depended on pH and became a minimum around pH 5.0 which was the isoelectric point of BSA. The interfacial tension between BSA solution and corn oil was minimized at pH 5.0. Interesting results were obtained concerning the ionic-strength dependence of stability. When the ionic strength was set below 30 mM, the emulsions became more stable with the increase of BSA concentration at pH 6.7 but the opposite behavior (enhanced destabilization) was confirmed at pH 5.0 with the BSA content. In high ionic strength conditions (ca. > or = 80 mM NaCl), however, BSA-stabilized emulsions became fairly stable even at pH 5.0. These results suggested that BSA molecules having no net charge induced some attractive interactions (e.g., bridging or depletion) in low ionic strength but steric stabilization in high ionic strength, respectively.