Functionalized organic dyes containing a phenanthroimidazole donor for dye-sensitized solar cell applications

Five functionalized organic dyes (H6-10) containing a phenanthroimidazole unit as an electron donor were synthesized and characterized for use in dye-sensitized solar cell (DSSC) applications. Under standard global AM 1.5 solar conditions, the DSSCs based on dye H6 displayed the best performance, with an incident photon-to-current conversion efficiency (IPCE) exceeding 70% at wavelengths of 400–530 nm, a short-circuit photocurrent density of 10.98 mA cm^?2, an open-circuit voltage of 0.68 V, a fill factor of 0.69, and an overall conversion efficiency of 5.12%. This efficiency is ～94% of that for JK2 cells (5.46%) and ～72% of that for N719 cells (7.07%) under the same conditions.     

不同受体结构染料共敏化对染料敏化太阳电池性能的影响

为了拓宽染料敏化太阳电池对太阳光谱的响应范围,提高电池的光电转换效率,将两种含有不同受体结构（绕丹宁-3-乙酸基（RA）和氰基丙烯酸基（CA））的三苯胺染料（TR1和TC1）进行共敏化。TR1染料平伏吸附在TiO₂表面,而TC1染料直立吸附在TiO₂表面。将两种染料按照不同摩尔比共敏化TiO₂后,TC1占据TR1的部分位置,拓展光谱的同时也抑制了电荷复合,电子寿命较TR1敏化的太阳电池长。在TR1与TC1摩尔比为5：5的共敏剂溶液敏化的共敏电池器件中,短路光电流密度（J_sc）为11.7 mA/cm²,开路电压（V_oc）为704 mV,填充因子（FF）为0.73,光电转换效率（η）为6.03%。该结果明显优于单一染料敏化的电池器件。     

Near infrared thieno[3,4-b]pyrazine sensitizers for efficient quasi-solid-state dye-sensitized solar cells

Three near infrared (NIR) metal-free organic sensitizers (FNE32, FNE34, FNE36) based on the thieno[3,4-b]pyrazine derivative have been designed and synthesized for application in quasi-solid-state dye-sensitized solar cells (DSSCs). These organic dyes demonstrate maximum absorption bands at 596-625 nm due to the presence of the thieno[3,4-b]pyrazine derivative, which facilitates the intramolecular electron transfer from the donor to the acceptor. Quasi-solid-state DSSCs based on FNE34 display efficient photoelectric conversion over the whole visible range extending into the NIR region up to 900 nm with maximum incident monochromatic photon-to-electron conversion efficiency (IPCE) of 77%, yielding a short-circuit photocurrent density of 16.24 mA cm(-2) and a power conversion efficiency of 5.30%. To the best of our knowledge, this is the highest efficiency for quasi-solid-state DSSCs based on an organic NIR dye. When exposed to one-sun illumination for 1000 h, the quasi-solid-state DSSC based on FNE34 exhibits good long-term stability with almost constant power conversion efficiency.     

Thiophene-fused coplanar sensitizer for dye-sensitized solar cells

We have designed and synthesized a novel ladder-type heteroacene dye consisting uniquely of thiophene segments as a photosensitizer for the dye-sensitized solar cells (DSSCs). The onset of the IPCE spectrum for the dye not only reaches up to 700 nm with a high IPCE (>60%) but also a solar energy-to-electricity conversion efficiency of 2.31% is achieved. Even though the efficiency is slightly lower than those of other dyes reported previously, this work opens up a new strategy to design heteroaromatic fused photosensitizers for DSSCs.     

Design of an organic chromophore for p-type dye-sensitized solar cells

A successful model for the design of efficient dyes for p-type dye-sensitized solar cells (DSSCs) is presented. As an example, a novel and efficient organic dye containing a triphenylamine chromophore has been synthesized and successfully applied in a p-type DSSC. The highest incident photon-to-current conversion efficiency (IPCE) of 18% in the visible region has been obtained, which is the highest value so far in p-type DSSCs. This is remarkably high, considering that only 600 nm thin NiO mesoporous films were used as p-type DSSC electrodes.     

Molecular Design of TPD-based Organic A-π-D-π-A Dyes for Dye-sensitized Solar Cells

An interesitng class of organic A-π-D-π-A dyes based on an N,N,N′,N′-tetraphenylbenzidine(TPD) unit as donor was designed and synthesized for dye-sensitized solar cells(DSSCs). TPD-4-based DSSCs gave a short circuit photocurrent density(J_sc) of 16.67 mA/cm², a open circuit voltage(V_oc) of 0.635 V and a fill factor(ff) of 0.68, achieving a solar-to-electricity conversion efficiency(η) of 7.22% in preliminary tests. The N3-sensitized device gave an η value of 8.02% with a J_sc of 18.81 mA/cm², a V_oc of 0.630 V and an ff of 0.68 under the same conditions. The incident photo-to-current efficiency(IPCE) values above 70% observed in a range of 460 to 600 nm with a maximum value of 80% at 500 nm indicate that the TPD-4-based DSSC shows a high performance. Under the same conditions, the DSSC based on N3 provided the IPCE values above 70% in a range of 490 to 580 nm with a maximum value of 76% at 500 nm. Both further optimization of the device processing and structural modification of these dyes are anticipated to make the device give even better performances.     

New bithiazole-based sensitizers for efficient and stable dye-sensitized solar cells

A series of new push-pull organic dyes (BT-I-VI), incorporating electron-withdrawing bithiazole with a thiophene, furan, benzene, or cyano moiety, as π?spacer have been synthesized, characterized, and used as the sensitizers for dye-sensitized solar cells (DSSCs). In comparison with the model compound T1, these dyes containing a thiophene moiety between triphenylamine and bithiazole display enhanced spectral responses in the red portion of the solar spectrum. Electrochemical measurement data indicate that the HOMO and LUMO energy levels can be tuned by introducing different π?spacers between the bithiazole moiety and cyanoacrylic acid acceptor. The incorporation of bithiazole substituted with two hexyl groups is highly beneficial to prevent close π-π aggregation, thus favorably suppressing charge recombination and intermolecular interaction. The overall conversion efficiencies of DSSCs based on bithiazole dyes are in the range of 3.58 to 7.51?%, in which BT-I-based DSSCs showed the best photovoltaic performance: a maximum monochromatic incident photon-to-current conversion efficiency (IPCE) of 81.1?%, a short-circuit photocurrent density (J(sc)) of 15.69?mA?cm(-2), an open-circuit photovoltage (V(oc)) of 778?mV, and a fill factor (ff) of 0.61, which correspond to an overall conversion efficiency of 7.51?% under standard global AM 1.5 solar light conditions. Most importantly, long-term stability of the BT-I-III-based DSSCs with ionic-liquid electrolytes under 1000?h of light soaking was demonstrated and BT-II with a furan moiety exhibited better photovoltaic performance of up to 5.75?% power conversion efficiency.     

Increasing the conversion efficiency of dye-sensitized TiO2 photoelectrochemical cells by coupling to photonic crystals

The mechanism of enhancing the light harvesting efficiency of dye-sensitized TiO(2) solar cells by coupling TiO(2) inverse opals or disordered scattering layers to conventional nanocrystalline TiO(2) films has been investigated. Monochromatic incident photon-to-current conversion efficiency (IPCE) at dye-sensitized TiO(2) inverse opals of varying stop band wavelengths and at disordered titania films was compared to the IPCE at bilayers of these structures coupled to nanocrystalline TiO(2) films and to the IPCE at nanocrystalline TiO(2) electrodes. The results showed that the bilayer architecture, rather than enhanced light harvesting within the inverse opal structures, is responsible for the bulk of the gain in IPCE. Several mechanisms of light interaction in these structures, including localization of heavy photons near the edges of a photonic gap, Bragg diffraction in the periodic lattice, and multiple scattering events at disordered regions in the photonic crystal or at disordered films, lead ultimately to enhanced backscattering. This largely accounts for the enhanced light conversion efficiency in the red spectral range (600-750 nm), where the sensitizer is a poor absorber.     

Enhanced Charge Separation Efficiency in Pyridine‐Anchored Phthalocyanine‐Sensitized Solar Cells by Linker Elongation

A series of zinc phthalocyanine sensitizers ( PcS22 – 24 ) having a pyridine anchoring group are designed and synthesized to investigate the structural dependence on performance in dye‐sensitized solar cells. The pyridine‐anchor zinc phthalocyanine sensitizer PcS23 shows 79 % incident‐photon to current‐conversion efficiency (IPCE) and 6.1 % energy conversion efficiency, which are comparable with similar phthalocyanine dyes having a carboxylic acid anchoring group. Based on DFT calculations, the high IPCE is attributed with the mixture of an excited‐state molecular orbital of the sensitizer and the orbitals of TiO₂. Between pyridine and carboxylic acid anchor dyes, opposite trends are observed in the linker‐length dependence of the IPCE. The red‐absorbing PcS23 is applied for co‐sensitization with a carboxyl‐anchor organic dye D131 that has a complementary spectral response. The site‐selective adsorption of PcS23 and D131 on the TiO₂ surface results in a panchromatic photocurrent response for the whole visible‐light region of sun light.     

N,N-二苯基取代的芳炔化合物的合成及光伏性能

以简单原料出发,通过Sonogashira偶联反应和三甲基硅基(TMS)的保护与脱保护,合成了一系列N,N-二苯基取代的芳炔化合物SC1～SC5.这类化合物是以N,N-二苯基为电子给体,羧基为电子受体,芳香炔体系为共轭桥的染料.将化合物SC5吸附到TiO2膜上制备成有机染料敏化太阳能电池,在AM 1.5,100 mW/cm2的模拟太阳光下,电池的光电转换效率(IPCE)值最大达到64%,而且在350～580 nm的范围内都可达到50%以上.电池的短路电流密度Jsc=8.0mW/cm2,开路电压Voc=0.75 V,填充因子为FF=0.70,总光电转换效率η=4.2%.     

Spectral broadening in quantum dots-sensitized photoelectrochemical solar cells based on CdSe and Mg-doped CdSe nanocrystals

In order to absorb a broad spectrum in visible region, a co-sensitized TiO₂ electrode was prepared by CdSe and Mg-doped CdSe quantum dots (Q dots). The power conversion efficiency of the co-sensitized Q dots photoelectrochemical solar cells (PECs) showed 1.03% under air mass 1.5 condition (I = 100 mW/cm²), which is higher than that of individual Q dots-sensitized PECs. The incident-photon-to-current conversion efficiency of the co-sensitized PECs showed absorption peaks at 541 and 578 nm corresponding to the two Q dots and displayed a broad spectral response over the entire visible spectrum in the 500–600 nm wavelength domains.     

Enhanced performance of ruthenium dye-sensitized solar cell by employing an organic co-adsorbent of N,N'-bis((pyridin-2-yl)(methyl) methylene)-o-phenylenediamine

A pyridine-anchor co-adsorbent of N,N'-bis((pyridin-2-yl)(methyl) methylene)-o-phenylenediamine(named BPPI) is prepared and employed as co-adsorbent in dye-sensitized solar cells(DSSCs). The prepared co-adsorbent could overcome the deficiency of N719 absorption in the low wavelength region of visible spectrum, offset competitive visible light absorption of I₃^-, enhance the spectral responses of the co-adsorbed TiO₂ film in region from 300 nm to 750 nm, suppress charge recombination, prolong electron lifetime, and decrease the total resistance of DSSCs. The optimized cell device co-sensitized by BPPI/N719 dye gives a short circuit current density of 12.98 mA cm^-2, an open circuit voltage of 0.73 V, and a fill factor of 0.66 corresponding to an overall conversion efficiency of 6.22% under standard global AM 1.5 solar irradiation, which is much higher than that of device solely sensitized by N719(5.29%) under the same conditions. Mechanistic investigations are carried out by various spectral and electrochemical characterizations.     

Photoelectrochemical solar cell properties of heteropolytungstic acid-incorporated TiO2 nanodisc thin films

Thin film of heteropolytungstic acid (HPA)-incorporated TiO₂ nanodisc was fabricated, and its photovoltaic performances were observed as a function of irradiation wavelength from 400 nm to 750 nm. Its incident photon-to-current efficiency (IPCE) was determined to be 18.6% around 500 nm, with energy conversion efficiency of 6.9%, which were observed to be further enhanced to 23% and 9%, respectively, by adsorption of ruthenium or porphyrin dyes. Complementary electron transports from both HPA and dyes to TiO₂ nanodisc seems to avoid most of the backward electron or hole transfer reactions to enhance the photoelectrochemical efficiencies of dye-sensitized solar cells.     

Novel organic dye sensitizers containing fluorenyl and biphenyl moieties for solar cells

Three novel triarylamine dyes(AFL1-AFL3) containing fluorenyl and the biphenyl moieties have been designed and synthesized for application in dye-sensitized solar cells.The light-harvesting capabilities and photovoltaic performance of these dyes were investigated systematically through comparison of different π-bridges.The dye with a furan linker exhibited a higher open-circuit voltage(V_(OC)) and monochromatic incident photon-to-current conversion efficiency(IPCE) compared to thiophene and benzene linker.Thus,AFL3 containing a furan linker exhibited the maximum overall conversion efficiency of 5.81%(V_(OC) = 760 mV,J_(SC) = 11.36 mA cm~2 and ff=0.68) under standard global AM 1.5 G solar condition.     

D-π-A dye system containing cyano-benzoic acid as anchoring group for dye-sensitized solar cells

A D-π-A dye (KM-1) incorporating cyano-benzoic acid as a new acceptor/anchoring group has been synthesized for dye-sensitized solar cells (DSCs) with a high molar extinction coefficient of 66,700 M(-1) cm(-1) at 437 nm. Theoretical calculations show that the hydrogen bond between -CN and surface hydroxyl leads to the most stable configuration on the surface of TiO(2). In addition, the adsorption of the dye on TiO(2) follows a Brunauer-Emmett-Teller (BET) isotherm. Multilayer adsorption of KM-1 on TiO(2) seems to take place particularly at higher dye concentrations. DSC device using KM-1 reached a maximum incident photon-to-current conversion efficiency (IPCE) of 84%, with a solar to electric power conversion efficiency (PCE) of 3.3% at AM1.5 G illumination (100 mW cm(-2)). This new type of anchoring group paves a way to design new dyes that combine good visible light harvesting with strong binding to the metal oxide surface.     

Influence of Modification of Counter Electrode on Photoelectric Properties of Dye-sensitized TiO2 Solar Cells

A dye-sensitized nanocrystalline TiO2 solar cell(DYSC) was assembled, of which counter electrode was modified already by platinum, nickel and carbon. It was found that the DYSC had better photoelectric performance when the electrode was modified by platinum than by nickel and carbon. The influence of the incidence light wavelength on the incidence monochromatic photoelectric conversion effieieney(IPCE) was investigated.The result shows that the IPCE mainly depends on the short-circuit current density(Isc) of a DYSC, and the IPCE reaches 48.32% under the irradiation with the wavelength of 560 nm when the counter electrode of a DYSC was modified by platinum. The influence of incident light intensity on the photoelectric properties of a DYSC was also investigated. It was found that the Isc and open-circuit voltage(Voc) increased and the fill factor(ff) of the DYSC decreased with the increase of the incident light intensity.     

Squarylium Cyanine Dyes for Photoelectric Conversion

Asanimportantclassoffunctionalmaterials,squaryliumcyaninedyespossessmanyexcellentpropertiessuchasstablestructures,outstandingphotoconductivityaswellassmallthermalconductivity,andexhibitintenseandsharpabsorptionbandsinthevisibleandnearinfraredregionwithhighlightharvestingcapacity,whichopenupextensiveapplicationsinthevariousfieldsl-3.Inthispaper,twosymmetricalsquaryliumindocyanineswiththeintroductionofhydroxyethylandsulfopropylgroupsontheheterocyclicnitrogenweresynthesizedandcharacterizedbyUV,I…     

Perylene anhydride fused porphyrins as near-infrared sensitizers for dye-sensitized solar cells

Two perylene anhydride fused porphyrins 1 and 2 have been synthesized and employed successfully in dye-sensitized solar cells (DSCs). Both compounds showed broad incident monochromatic photon-to-current conversion efficiency spectra covering the entire visible spectral region and even extending into the near-infrared (NIR) region up to 1000 nm, which is impressive for ruthenium-free dyes in DSCs.     

Modified phthalocyanines for efficient near-IR sensitization of nanostructured TiO(2) electrode

A zinc phthalocyanine with tyrosine substituents (ZnPcTyr), modified for efficient far-red/near-IR performance in dye-sensitized nanostructured TiO(2) solar cells, and its reference, glycine-substituted zinc phthalocyanine (ZnPcGly), were synthesized and characterized. The compounds were studied spectroscopically, electrochemically, and photoelectrochemically. Incorporating tyrosine groups into phthalocyanine makes the dye ethanol-soluble and reduces surface aggregation as a result of steric effects. The performance of a solar cell based on ZnPcTyr is much better than that based on ZnPcGly. Addition of 3alpha,7alpha-dihydroxy-5beta-cholic acid (cheno) and 4-tert-butylpyridine (TBP) to the dye solution when preparing a dye-sensitized TiO(2) electrode diminishes significantly the surface aggregation and, therefore, improves the performance of solar cells based on these phthalocyanines. The highest monochromatic incident photo-to-current conversion efficiency (IPCE) of approximately 24% at 690 nm and an overall conversion efficiency (eta) of 0.54% were achieved for a cell based on a ZnPcTyr-sensitized TiO(2) electrode. Addition of TBP in the electrolyte decreases the IPCE and eta considerably, although it increases the open-circuit photovoltage. Time-resolved transient absorption measurements of interfacial electron-transfer kinetics in a ZnPcTyr-sensitized nanostructured TiO(2) thin film show that electron injection from the excited state of the dye into the conduction band of TiO(2) is completed in approximately 500 fs and that more than half of the injected electrons recombines with the oxidized dye molecules in approximately 300 ps. In addition to surface aggregation, the very fast electron recombination is most likely responsible for the low performance of the solar cell based on ZnPcTyr.     

Improvement of dye-sensitized solar cells' performance via co-sensitization of new azo thiazole organic dyes with ruthenium (II) based N-719 dye

Three novel azo thiazole organic dyes, NA-1–3, have been synthesized and utilized as co-sensitizers in dye-sensitized solar cells (DSSCs). These co-sensitizers were designed with a thiazole ring π-bridge that mediates between the diazo (–N = N–) functional group and carboxylic acid anchoring unit. They possess a rod-like molecular structure and exhibit strong UV–vis absorption near 600 nm. Co-sensitization studies were also conducted with the ruthenium complex N719. The co-sensitized DSSCs showed enhanced short-circuit and open-circuit photocurrents (Jsc) and voltages (Voc), resulting in more efficient photovoltaic performance compared to N719 (PCE 7.25%). Electrochemical impedance spectroscopy (EIS) and incident photon to current efficiency (IPCE) were employed to investigate the underlying reasons for these improvements. It was found that co-sensitization effectively reduced electron recombination, resulting in a higher Voc without compromising photocurrent loss.