RBM band shift-evidenced dispersion mechanism of single-wall carbon nanotube bundles with NaDDBS

The dispersion process of single-wall carbon nanotube (SWNT) by using sodium dodecylbenzene sulfonate (NaDDBS) was studied by means of surface tension measurements, ultraviolet-visible (UV-Vis) spectroscopy, scanning electron microscopy (SEM), and transmission electron spectroscopy (TEM). The critical micelle concentration (CMC) and the concentration where the surface tension begins to drop increase by the presence of SWNT. The isotherm of NaDDBS amount adsorbed on SWNT shows the plateau region at 0.2-6 mM and the saturated region above 40 mM. The external surface of SWNT bundle is fully covered with adsorbed NaDDBS at the plateau region, showing that SWNTs can be dispersed with the bundle form. On the other hand, SWNTs are dispersed in individual tubes at the saturated region, where the adsorption amount corresponds to coating of individual tube surfaces with NaDDBS. This dispersion state was confirmed by SEM and TEM observations. The effect of the dispersion state of SWNTs on radial breathing mode in Raman spectrum gave inherent peak shifts, being the in situ evidences on the step-wise dispersion mechanism of the SWNT bundle to the individual tubes.     

聚二乙烯基苯微球的合成及其表征研究

采用分散聚合方法制备了聚二乙烯基苯微球 ,研究了引发剂、稳定剂、单体 溶剂比例和溶剂种类对微球粒径及其分布的影响 ,在适当的条件下可以得到平均粒径较大、粒径分布较窄的微球 .用红外光谱法研究了聚合物微球内稳定剂、悬挂双键以及对位和间位二乙烯基苯含量随聚合过程的进行发生的变化 .测得的微球TG曲线表明 ,聚合物微球具有良好的热稳定性 .     

A novel preparation method for microspheres of water soluble polymers using polypropyleneglycol as the dispersion medium

Polypropyleneglycol (PPG) was used as a dispersion medium for the preparation of microspheres (MS) consisting of starch, gelatin, whey protein or dextran. Aqueous solutions of the polymers were dispersed in PPG at various initial temperatures and then the systems were cooled to 0.5 degrees C to allow water in the dispersed phase to dissolve in PPG. The particle size of the starch-MS was dependent on the initial temperature of PPG in the preparation process. There were two different processes for particle generation in the procedure. One of them was via the formation of a temporary emulsion during the early phase of dispersion of the aqueous polymer solution into PPG. The other was via the stable emulsion in which the aqueous polymer solution was dispersed in water-saturated PPG. The particle size generated in the former process was dependent on the initial temperature: a high temperature gave large particles but a low temperature gave small particles, while that in the latter process was temperature-independent. This preparation method for MS will be useful for the formulation of heat-sensitive material, such as protein-containing drugs.     

Surface Modification of Carbon Nanotube by Poly(ethylene glycol) for the Preparation of Poly(vinyl alcohol) Nanocomposite

Herein, PEGylated multi-walled carbon nanotube (MWNT) was prepared for the successive fabrication of poly(vinyl alcohol) PVA/MWNT nanocomposite film by solution casting. The surface modified MWNT showed a good colloidal stability in a polar solvent, i.e., water. Also, the PEGylated MWNT had an improved dispersion stability in aqueous PVA solution. The mixture of PEGylated MWNT and PVA dissolved in water was film casted and the dispersion uniformity and corresponding improvement of electrical conductivity were investigated. The electrical conductivity of PVA/modified MWNT composite film was three-fold higher than that of PVA/pristine MWNT composite film due to the much improved distribution uniformity of modified MWNT in PVA matrix.     

Non-aqueous dispersion properties of pure barium titanate for tape casting

The dispersion properties of concentrated (25.0 and 50.0 vol.%) dispersions of high purity barium titanate powder dispersed in a methyl ethyl ketone (MEK) -ethanol solvent of moderate dielectric constant were studied in an effort to improve the uniformity of tape cast and sintered bodies. An amphoteric phosphate ester surfactant was found to be an effective dispersant. The dispersion properties of the phosphate ester were subsequently investigated by rheological, adsorption, conductivity, and electrophoretic mobility methods in order to evaluate a dispersion mechanism.Optimum dispersion occurred at an azeotrope solution of MEK and ethanol. The barium titanate particles dispersed in dry solvents exhibited a greater degree of dispersion than particles dispersed in hydrated solvents. The adsorption isotherm for the adsorption of the phosphate ester onto barium titanate particle surfaces using dry solvents exhibited a well-defined plateau corresponding to monolayer surface coverage. The plateau was less well defined for particles dispersed in hydrated solvents. Polymer coverage remained essentially constant with varying solvent composition. Optimum dispersion and maximum zeta potential occurred at a concentration of phosphate ester which corresponded to initial monolayer coverage. A maximum in the zeta potential also occurred at the azeotrope solution of MEK-ethanol and again coincided with optimum dispersion.Conductivity data indicate a dynamic adsorption-desorption dissociation mechanism for the ionic phosphate ester at the solid/liquid interface. The adsorption and conductivity data indicate the mechanism of dispersion stability is a combination of electrostatic and steric phenomena.     

Dispersing carbon nanotubes using surfactants

We review the recent advances in dispersing single-wall carbon nanotubes (SWNTs) using amphiphilic surfactants in aqueous solutions. Three aspects are discussed. (1) On the organization of surfactant molecules with SWNTs, new insights at the microscopic level arise from electron microscopy and detailed computer simulation studies. (2) Quantitative measurements, such as molecular interactions between functional groups and SWNTs, the coverage of surfactant on SWNTs in solution, the charge state of the SWNT/surfactant complex, and the degree of dispersion are critical for better understanding dispersion mechanisms and for the further development of dispersion strategies. (3) The thermodynamic driving forces and the role of metastability in the structure of surfactant dispersed SWNT suspensions are analyzed. An outlook on practical and fundamental issues is also presented.     

铂粒子修饰单壁碳纳米管/聚苯胺复合膜对甲醛的电催化氧化

在溶有单壁碳纳米管(SWNTs)的苯胺溶液中, 通过电化学共聚合法成功制备了单壁碳纳米管(SWNT)/聚苯胺(PANI)复合膜. 用电沉积法将铂沉积到SWNT/PANI复合膜上. 样品的成分和形貌分别用XRD和SEM表征. 四探针和电化学交流阻抗的研究表明被PANI包裹的SWNTs整齐地排列在复合膜中, 从而提高了复合膜的电导率, 促进了电荷转移. 循环伏安(CV)说明Pt修饰的SWNT/PANI复合膜对于甲醛氧化具有良好的电催化活性及稳定性. 研究结果表明SWNT/PANI复合膜是一种非常好的催化剂载体, 有着广泛的应用前景.     

Confocal microscopy studies of shear‐induced coalescence in blends of poly(butyl methacrylate) and poly(2‐ethylhexyl methacrylate)

This article reports the results of confocal fluorescence microscopy studies of shear‐induced coalescence in binary blends of poly(2‐ethylhexyl methacrylate) (PEHMA; 90 wt %) and poly(butyl methacrylate) (PBMA; 10 wt %). We prepared the blends by casting a mixture of latex dispersions of the components onto a substrate and allowing the film to dry under ambient conditions. The initial morphology of the film was a dispersion of 120‐nm PBMA spheres in a continuous PEHMA matrix. One‐fifth of the PBMA particles were labeled with anthracene, the emission of which we observed with confocal microscopy. The blends were sheared in a parallel‐plate rheometer at 80 and 100 °C for 1 and 10 h. Careful image analysis allowed us to estimate the mean size of the dispersed phase and the width of the size distribution. The results were compared with the theoretical limits of Wu and Taylor. After 10 h of shearing, the mean particle size decreased and the particle distribution became narrower in comparison with the results obtained after 1 h of shearing. We explain this result by inferring that before the sample reached steady‐state morphology, its rate of coalescence was greater than the rate of particle breakup. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 2317–2332, 2001     

Facile method for fabrication of nanocomposite films with an ordered porous surface

This paper presents a novel and facile method for the fabrication of nanocomposite films with ordered porous surface structures. In this approach, a water-borne poly(styrene-co-butyl acrylate-co-acrylic acid)/silica nanocomposite dispersion was synthesized in situ by surfactant-free emulsion polymerization by using 3-allyloxy-2-hydroxy-1-propanesulfonate as a polymerizable surfactant. When this dispersion was dried to form a film at a certain temperature, an ordered porous structure could be directly obtained on the surface of the nanocomposite film. SEM, TEM, and AFM were employed to observe the morphology, and XPS and particle analyzer were used to analyze the surface composition of the ordered porous nanocomposite film and the particle size, respectively.     

The effects of altered reaction conditions on the properties of anionic poly(urethane-urea) dispersions and films cast from the dispersions

Aqueous anionic polyurethane (PU) dispersions were synthesised from a polyester polyol, isophorone diisocyanate and α,α-dimethylol propionic acid using the prepolymer mixing process. Samples were neutralised by the addition of triethyl amine. The polymer chains were dispersed in water and extended with 1,2-ethylene diamine. The differences in the dispersion characteristics and the mechanical properties of the polymer films cast and dried from the dispersions caused by altered reaction conditions were determined.The reaction conditions proved to affect both the colloidal properties of the dispersions as well as the mechanical properties of the films. The neutralisation, the dispersion and the chain extension methods had all an influence on the average size of the formed PU particles. For the films, a change in the mechanical properties and probably in the amount of hard and soft domain separation was also observed. A good control over the properties was obtained by selecting the reaction parameters carefully. In particular, the dispersion method in which the prepolymer solution was added to water and not vice versa led to a considerably lower viscosity during the dispersion process. Thus a wider choice of raw materials was facilitated.     

Colloidal complexes from poly(vinyl amine) and carboxymethyl cellulose mixtures

The phase behaviors of polyelectrolyte complexes formed from dilute solutions of poly(vinyl amine) (PVAm) and carboxymethyl cellulose (CMC) were determined as a function of overall composition and pH. The phase diagram included regions with soluble complexes, colloidal complexes, and macroscopic precipitates. Colloidal complexes were stable when either polymer was in sufficient excess to give electrosteric stabilization. The polymer mixing ratios giving complexes with an isoelectric point of 7 could be predicted from a simple model using the degree of ionization vs pH data for PVAm and CMC. The model failed at extreme pH values because not all added polymer was incorporated into the complexes. At pH 7, essentially all the added polymer was incorporated into the colloidal complex or precipitate, as long as the mixing ratio was within +/-10% of charge stoichiometry. The interaction of PVAm and CMC at pH 7 was endothermic, supporting the generally accepted viewpoint that the interaction of oppositely charged polyelectrolytes is entropy-driven. Although the colloidal complexes had a broad particle size distribution, the average particle size was rather insensitive to mixing ratio. By contrast, complex size was sensitive to electrolyte concentration with no complex formation when the NaCl concentration was > or =2 M.     

Polymeric microspheres by radiation copolymerization of acrolein and various monomers at low temperatures

The preparation of polymeric microspheres having aldehyde groups by radiation polymerization of acrolein solution containing various monomers at low temperatures was studied, in which the monomer solution was dispersed with polyvinyl alcohol in order to obtain monomeric microspheres and then irradiated. The particle size of the microspheres from acrolein — 2-hydroxyethyl methacrylate system varied with polymerization and dispersion condition, in which the particle size increase of the concentration of 2-hydroxy ethyl methacrylate and its particle size distribution was broadened. In acrolein — polyethyleneglycol dimethacrylate system, the effect of the molecular structure of monomers on the particle size was studied, and it was found that the particle size decreased with number of oxyethylene units in monomers.     

Effect of the composition of the medium and electroflotation processing parameters on extraction efficiency of chromium(III) dispersed phase from aqueous solutions

Influence exerted by the composition of the medium (solution pH, ionic composition, presence of flocculants and surfactants), physicochemical properties of the dispersed phase (particle size, electrokinetic potential), and technological parameters of the electroflotation process (volume current density, magnetic treatment, solution temperature) on the efficiency of the electroflotation extraction of poorly soluble chromium(III) compounds from aqueous solutions was studied. It was shown that the extraction efficiency directly depends on the composition of the medium, which determines the physicochemical properties of poorly soluble chromium(III) compounds, and on the size of particles and their minimum surface charge. The optimal technological parameters of the electroflotation process are suggested.     

Colloid stability of lipid/polyelectrolyte decorated latex

The colloid stability of supramolecular assemblies composed of the synthetic cationic lipid dioctadecyldimethylammonium bromide (DODAB) on carboxymethyl cellulose (CMC) supported on polystyrene amidine (PSA) microspheres was evaluated via turbidimetry kinetics, dynamic light scattering for particle sizing, zeta-potential analysis, and determination of DODAB adsorption on CMC-covered particles. At 0.1 g L(-1) CMC and 2 x 10(11) PSA particles/mL, CMC did not induce significant particle flocculation, and a vast majority of CMC-covered single particles were present in the dispersion so that this was the condition chosen for determining DODAB concentration (C) effects on particle size and zeta potentials. At 0.35 mM DODAB, charge neutralization, maximal size, and visible precipitation indicated extensive flocculation and minimal colloid stability for the DODAB/CMC/PSA assembly. At 0.1 g L(-1) CMC, isotherms of high affinity for DODAB adsorption on CMC-covered particles presented a plateau at a limiting adsorption of 700 x 10(17) DODAB molecules adsorbed per square meter PSA which was well above bilayer deposition on a smooth particle surface. The polyelectrolyte layer on hydrophobic particles was swelled and fluffy (ca. 11-nm hydrodynamic thickness), and maximal adsorption of DODAB lipid onto this layer produced a compressed composite cationic film with 20 mV of zeta potential and about 10-nm mean thickness. The assembly of cationic lipid/CMC layer/polymeric particle was stable only well above charge neutralization of the polyelectrolyte by the cationic lipid, at relatively large lipid concentrations (at and above 1 mM DODAB) with charge neutralization leading to extensive particle aggregation.     

(n,m) Abundance evaluation of single-walled carbon nanotubes by fluorescence and absorption spectroscopy

A methodology that takes into account the (n,m) structure of single-walled carbon nanotubes (SWNTs), through an exciton-exciton resonance model and an electron-phonon interaction model, was employed in order to evaluate the semiconducting (n,m) abundance of two SWNT samples (i.e., Co-MCM-41 and HiPco). This was based on photoluminescence and near-infrared absorption data obtained on aqueous suspensions of individually dispersed SWNTs. In the absence of known (n,m) abundance SWNT samples, we resorted to determining the diameter distribution curves for both samples, which were found to obey an unsymmetrical log-normal distribution, typical for vapor-phase particle growth. Using this log-normal function, we reconstructed the near-infrared E S11 absorption spectrum of the narrow diameter distribution Co-MCM-41 SWNT sample, which in turn enabled us to assess the predictions of these two theoretical models. High spectral reconstruction accuracy was obtained from the electron-phonon interaction model when considering (11,0) and (10,0) zigzag nanotubes, along with (n,m) line widths inversely proportional to their extinction coefficients.     

Microgel Particles as a Matrix for Polymerization: A Study of Poly(N-isopropylacrylamide)-Poly(N-methylpyrrole) Dispersions

Poly(N-isopropylacrylamide) (PNIPAM) microgel particles dispersed in water have been used as a matrix for the polymerization of a hydrophobic monomer, N-methylpyrrole (MPy). The presence of poly(MPy) (PMPy) within the dried composite particles has been confirmed using electron paramagnetic resonance (EPR) measurements which show a characteristic free-radical signal at g=2.007. Electron microscopy data (TEM) show that the composite PNIPAM-xPMPy particles have a "raspberry-like" morphology. (The value for x represents the volume percent of MPy added during synthesis with respect to the total microgel volume.) PCS data indicate that PMPy occupies the majority of the collapsed composite particle volume. The maximum value of x consistent with colloid stability for PNIPAM-xPMPy dispersions is 4.5%. Higher values of x result in coagulation due to interparticle bridging by PMPy. Variable temperature PCS measurements of the PNIPAM-xPMPy dispersions have been used to study the thermally induced collapse of the composite particles. The extent of collapse becomes less with increasing values for x. The embedded PMPy particles restrict the extent of PNIPAM network contraction. The stability of the PNIPAM-4.5PMPy dispersions was investigated by means of turbidity measurements using aqueous 0.1 M NaCl solution. The upper critical flocculation temperatures (UCFT) for PNIPAM and PNIPAM-4.5PMPy dispersions were identical (38-39 degrees C). The flocculation observed was found to be fully reversible. The composite dispersion stability in the absence of salt was attributed to electrosteric stabilization afforded by the PNIPAM matrix. These results indicate that PNIPAM microgel particles may have application as a matrix for the polymerization of hydrophobic monomers in water. Copyright 2000 Academic Press.     

Synthesis of gel type dispersion polymers via living dispersion polymerization (LDP)

A gel type disperse polystyrene/divinylbenzene (DVB) copolymer was successfully prepared in hydrocarbon via ‘living dispersion polymerization (LDP)’ method. Characterization of the dispersed polymers was performed by a combination of size-exclusion chromatographic and transmission electron microscopic analyses. Poly(t-butylstyryl)lithium with 3,5 × 10⁴ g/mol of molecular weight was used as a steric stabilizing moiety in the living dispersion polymerization. The particle size of the dispersed polymers was able to be controlled by both the mole ratio of the concentration of poly(t-butylstyryl)lithium to n-butyllithium and the amount of monomer to over 2 μm.     

Preparation of monodisperse ellipsoidal polystyrene particles

A method is described for the preparation of monodisperse ellipsoidal particles of polystyrene in the colloidal size range. Monodisperse polystyrene particles were dispersed in a solution of polyvinyl alcohol. This dispersion was then allowed to form, by evaporation, a thin film of polyvinyl alcohol containing spherical polystyrene particles. Strips of this film were clamped into a metal frame, heated rapidly in an oil bath to 200°C and stretched to a predetermined extent in order to convert the spherical particles into ellipsoids; the film was then cooled. A wide range of axial ratios for a variety of initial particle sizes was obtained by this method.     

Preparation of single-walled carbon nanotube (SWNT) gel composites using poly(ionic liquids)

This paper reports a new and practical route for synthesizing nanotube-polymeric ionic liquids gel by non-covalent functionalization of oxidized single-walled carbon nanotube (SWNT) surfaces with imidazolium-based poly(ionic liquids) (PILs), using in situ radical polymerization method. A black and homogeneous precipitate SWNTs was obtained as a gel form, which is well dispersed in aqueous solution without any aggregation. The formation of SWNT gels is explained by the electrostatic attractions or π-bonds between the SWNT surface and the PIL matrix. By anion-exchange reaction of PIL bound to SWNTs, hydrophilic anions in PIL were substituted with hydrophobic anions, resulting in an effective transfer of SWNT-PIL hydrogels to organogels. The result also showed that SWNTs can effectively improve the conductivity along with the thermal stability of nanocomposite gels.     

Cellulose Nanocrystal-Assisted Dispersion of Luminescent Single-Walled Carbon Nanotubes for Layer-by-Layer Assembled Hybrid Thin Films

Highly stable single-walled carbon nanotube (SWNT) dispersions are obtained after ultrasonication in cellulose nanocrystal (CN) aqueous colloidal suspensions. Mild dispersion conditions were applied to preserve the SWNT length in order to facilitate the identification of hybrid objects. This led to a moderate dispersion of 24% of the SWNTs. Under these conditions, atomic force microscopy (AFM) and transmission electron microscopy (TEM) experiments succeeded in demonstrating the formation of hybrid particles in which CNs are aligned along the nanotube axis by a self-assembly process. These SWNT/CN dispersions are used to create multilayered thin films with the layer-by-layer method using polyallylamine hydrochloride as a polyelectrolyte. Homogeneous films from one to eight bilayers are obtained with an average bilayer thickness of 17 nm. The presence of SWNTs in each bilayer is attested to by characteristic Raman signals. It should be noted that these films exhibit a near-infrared luminescence signal due to isolated and well-separated nanotubes. Furthermore, scanning electron microscopy (SEM) suggests that the SWNT network is percolating through the film.