Magnetotransport properties of two-dimensional electron gas in AlGaN/AlN/GaN heterostructures

Magnetotransport measurements are carried out on the AlGaN/AlN/GaN in an SiC heterostructure, which demonstrates the existence of the high-quality two-dimensional electron gas (2DGE) at the AlN/GaN interface. While the carrier concentration reaches 1.32 × 10¹³ cm ^{- 2} and stays relatively unchanged with the decreasing temperature, the mobility of the 2DEG increases to 1.21 × 10⁴ cm²/(V·s) at 2 K. The Shubnikov—de Haas (SdH) oscillations are observed in a magnetic field as low as 2.5 T at 2 K. By the measurements and the analyses of the temperature-dependent SdH oscillations, the effective mass of the 2DEG is determined. The ratio of the transport lifetime to the quantum scattering time is 9 in our sample, indicating that small-angle scattering is predominant.     

电子通量对ZnO/K2SiO3热控涂层光学性能的影响

 研究了电子通量对ZnO/K₂SiO₃热控涂层光学性能的影响。分别采用通量为5×10¹¹/cm²·s，8×10¹¹/cm²·s，1×10¹²/cm²·s 和5×10¹²/cm²·s的电子对试样进行辐照。电子辐照下涂层的光学性能发生了退化，并且发现了退化涂层在空气中的“漂白”现象。分析了ZnO/K₂SiO₃热控涂层光学性能的退化机制，同时讨论了电子通量对太阳光谱吸收系数的影响。实验结果发现，在5×10¹¹～1×10¹²/cm²·s的电子通量范围内，电子通量对ZnO/K₂SiO³热控涂层光学性能的影响相同。因此在这个电子通量范围内，采用加速地面试验来模拟空间的电子辐照效应是有效的。     

晶格匹配InAlN/GaN和InAlN/AlN/GaN材料二维电子气输运特性研究

文章研究了InAlN/GaN和引入AlN界面插入层形成的InAlN/AlN/GaN材料的输运性质. 样品均在蓝宝石上以脉冲金属有机物化学气相淀积法生长,霍尔迁移率变温特性具有典型的二维电子气(2DEG)特征. 综合各种散射机理包括声学形变势散射、压电散射、极性光学声子散射、位错散射、合金无序散射和界面粗糙度散射,理论分析了温度对迁移率的影响,发现室温下两种材料中2DEG支配性的散射机理都是极性光学波散射和界面粗糙度散射;AlN插入层对InAlN/GaN材料迁移率的改善作用一方面是免除2DEG的合金无序散射,另外还显著改善异质界面,抑制了界面粗糙度散射. 考虑到2DEG密度也是影响其迁移率的重要因素,结合实验数据给出了晶格匹配InAlN/GaN和InAlN/AlN/GaN材料的2DEG迁移率随电子密度变化的理论上限. 关键词： InAlN/GaN 二维电子气 迁移率     

高温AlN插入层对AlGaN/GaN异质结材料和HEMTs器件电学特性的影响

研究了在GaN缓冲层中插入40 nm厚高温AlN层的GaN外延层和AlGaN/GaN异质结材料, AlN插入层可以增加GaN层的面内压应力并提高AlGaN/GaN高电子迁移率晶体管（HEMTs）的电学特性. 在精确测量布拉格衍射角的基础上定量计算了压应力的大小. 增加的压应力一方面通过增强GaN层的压电极化电场, 提高了AlGaN/GaN异质结二维电子气（2DEG）面密度, 另一方面使AlGaN势垒层对2DEG面密度产生的两方面影响相互抵消. 同时, 这种AlN插入层的采用降低了GaN与AlGaN层之间的 关键词： 高温AlN插入层 AlGaN/GaN异质结 二维电子气 应力     

高电子迁移率晶格匹配InAlN/GaN材料研究

文章基于蓝宝石衬底采用脉冲金属有机物化学气相淀积(MOCVD)法生长的高迁移率InAlN/GaN材料,其霍尔迁移率在室温和77 K下分别达到949和2032 cm²/Vs,材料中形成了二维电子气(2DEG). 进一步引入1.2 nm的AlN界面插入层形成InAlN/AlN/GaN结构,则霍尔迁移率在室温和77 K下分别上升到1437和5308 cm²/Vs. 分析样品的X射线衍射、原子力显微镜测试结果以及脉冲MOCVD生长方法的特点,发现InAlN/GaN材料的结晶质量较高,与GaN晶格匹配的InAlN材料具有平滑的表面和界面. InAlN/GaN和InAlN/AlN/GaN材料形成高迁移率特性的主要原因归结为形成了密度相对较低(1.6×10¹³-1.8×10¹³ cm^-2)的2DEG,高质量的InAlN晶体降低了组分不均匀分布引起的合金无序散射,以及2DEG所在界面的粗糙度较小,削弱了界面粗糙度散射. 关键词： InAlN/GaN 脉冲金属有机物化学气相淀积 二维电子气 迁移率     

使用AlN/GaN超晶格势垒层生长高Al组分AlGaN/GaN HEMT结构

在蓝宝石衬底上生长了以AlN/GaN超晶格准AlGaN合金作为势垒的HEMT结构材料,并与传统AlGaN合金势垒样品进行了对比.在高Al组分(≥40%)情况下,超晶格势垒样品的表面形貌明显改进,电学性能特别是2DEG面电子浓度也有所改进.对超晶格势垒生长参数进行了初步优化,使得HEMT结构薄层电阻进一步降低,最后获得了251 Ω/□的薄层电阻. 关键词： AlGaN/GaN 结构 AlN/GaN超晶格 二维电子气 高电子迁移率晶体管     

N极性GaN/AlGaN异质结二维电子气模拟

通过自洽求解薛定谔方程和泊松方程,较系统地研究了GaN沟道层、AlGaN背势垒层、Si掺杂和AlN插入层对N极性GaN/AlGaN异质结中二维电子气(2DEG)的影响,分析表明,GaN沟道层厚度、AlGaN背势垒层厚度及Al组分变大都能一定程度上提高二维电子气面密度,AlGaN背势垒层的厚度和Al组分变大也可提高二维电子气限阈性,且不同的Si掺杂形式对二维电子气的影响也有差异,而AlN插入层在提高器件二维电子气面密度、限阈性等方面表现都较为突出,在模拟中GaN沟道层厚度小于5nm时无法形成二维电子气,超过20nm后二维电子气面密度趋于饱和,而AlGaN背势垒厚度超过40nm后二维电子气也有饱和趋势,对均匀掺杂和delta掺杂而言AlGaN背势垒层Si掺杂浓度超过5×10~(19)cm~(-3)后2DEG面密度开始饱和,而厚度为2nmAlN插入层的引入会使2DEG面密度从无AlN插入层时的0.93×10~(13)cm~(-2)提高到1.17×10~(13)cm~(-2)。     

Ⅲ族氮化物异质结构二维电子气研究进展

本文总结了近年来Ⅲ族氮化物半导体异质结构二维电子气的研究进展。从Ⅲ族氮化物材料晶格结构和特有的极化性质出发,重点讨论了AlGaN/GaN异质结构中二维电子气的性质,总结分析了异质结构中Al组分、势垒层厚度、应变弛豫度、掺杂等对二维电子气浓度和迁移率的影响,同时还涉及AlGaN/GaN/AlGaN,AlGaN/AlN/GaN和AlGaN/InGaN/GaN等异质结构二维电子气性质。     

Ⅲ族氮化物异质结构二维电子气研究进展

本文总结了近年来Ⅲ族氮化物半导体异质结构二维电子气的研究进展。从Ⅲ族氮化物材料晶格结构和特有的极化性质出发,重点讨论了AlGaN/GaN异质结构中二维电子气的性质,总结分析了异质结构中Al组分、势垒层厚度、应变弛豫度、掺杂等对二维电子气浓度和迁移率的影响,同时还涉及AlGaN/GaN/AlGaN,AlGaN/AlN/GaN和AlGaN/InGaN/GaN等异质结构二维电子气性质。     

3 MeV质子辐照对AlGaN/GaN高电子迁移率晶体管的影响

研究了AlGaN/GaN 高电子迁移率晶体管(HEMT)的质子辐照效应. 在3 MeV质子辐照下, 当辐照剂量达到1× 10¹⁵ protons/cm²时, 漏极饱和电流下降了20%, 最大跨导降低了5%. 随着剂量增加, 阈值电压向正向漂移, 栅泄露电流增加. 在相同辐照剂量下, 1.8 MeV质子辐照要比3 MeV质子辐照退化严重. 从SRIM软件仿真中得到不同能量质子在AlGaN/GaN异质结中的辐射损伤区, 以及在一定深度形成的空位密度. 结合变频C-V测试结果进行分析, 表明了质子辐照引入空位缺陷可能是AlGaN/GaN HEMT器件电学特性退化的主要原因.     

Effects of donor density and temperature on electron systems in AlGaN/AlN/GaN and AlGaN/GaN structures

It was reported by Shen et al that the two-dimensional electron gas (2DEG) in an AlGaN/AlN/GaN structure showed high density and improved mobility compared with an AlGaN/GaN structure, but the potential of the AlGaN/AlN/GaN structure needs further exploration. By the self-consistent solving of one-dimensional Schr\"{o}dinger--Poisson equations, theoretical investigation is carried out about the effects of donor density (0--1\times 10¹⁹cm^-3 and temperature (50--500K) on the electron systems in the AlGaN/AlN/GaN and AlGaN/GaN structures. It is found that in the former structure, since the effective \Delta E_c is larger, the efficiency with which the 2DEG absorbs the electrons originating from donor ionization is higher, the resistance to parallel conduction is stronger, and the deterioration of 2DEG mobility is slower as the donor density rises. When temperature rises, the three-dimensional properties of the whole electron system become prominent for both of the structures, but the stability of 2DEG is higher in the former structure, which is also ascribed to the larger effective \Delta E_c. The Capacitance--Voltage (C-V) carrier density profiles at different temperatures are measured for two Schottky diodes on the considered heterostructure samples separately, showing obviously different 2DEG densities. And the temperature-dependent tendency of the experimental curves agrees well with our calculations.     

The influence of AlN interlayers on the microstructural and electrical properties of p-type AlGaN/GaN superlattices grown on GaN/sapphire templates

AlN with different thicknesses were grown as interlayers (ILs) between GaN and p-type Al_0.15Ga_0.85N/GaN superlattices (SLs) by metal organic vapor phase epitaxy (MOVPE). It was found that the edge-type threading dislocation density (TDD) increased gradually from the minimum of 2.5×10⁹?cm^?2 without AlN IL to the maximum of 1×10¹⁰?cm^?2 at an AlN thickness of 20 nm, while the screw-type TDD remained almost unchanged due to the interface-related TD suppression and regeneration mechanism. We obtained that the edge-type dislocations acted as acceptors in p-type Al _x Ga_1?x N/GaN SLs, through the comparison of the edge-type TDD and hole concentration with different thicknesses of AlN IL. The Mg activation energy was significantly decreased from 153 to 70?meV with a?10-nm AlN IL, which was attributed to the strain modulation between AlGaN barrier and GaN well. The large activation efficiency, together with the TDs, led to the enhanced hole concentration. The variation trend of Hall mobility was also observed, which originated from the scattering at TDs.     

Properties of Si-doped GaN and AlGaN/GaN heterostructures grown by RF-MBE on high resistivity Fe-doped GaN

Silicon-doped GaN epilayers and AlGaN/GaN heterostructures were developed by nitrogen plasma-assisted molecular beam epitaxy on high resistivity iron-doped GaN (0001) templates and their properties were investigated by atomic force microscopy, x-ray diffraction and Hall effect measurements. In the case of high electron mobility transistors heterostructures, the AlN mole fraction and the thickness of the AlGaN barrier employed were in the range of from 0.17 to 0.36 and from 7.5 to 30 nm, respectively. All structures were capped with a 2 nm GaN layer.Despite the absence of Ga droplets formation on the surface, growth of both GaN and AlGaN by RF-MBE on the GaN (0001) surfaces followed a step-flow growth mode resulting in low surface roughness and very abrupt heterointerfaces, as revealed by XRD. Reciprocal space maps around the reciprocal space point reveal that the AlGaN barriers are fully coherent with the GaN layer.GaN layers, n-doped with silicon in the range from 10¹⁵ to 10¹⁹ cm⁻³ exhibited state of the art electrical properties, consistent with a low unintentional background doping level and low compensation ratio. The carrier concentration versus silicon cell temperatures followed an Arhenius behaviour in the whole investigated doping range. The degenerate 2DEG, at the AlGaN/GaN heteroiterfaces, exhibited high Hall mobilities reaching 1860 cm²/V s at 300 K and 10 220 cm²/V s at 77 K for a sheet carrier density of 9.6E12 cm⁻².The two dimensional degenerate electron gas concentration in the GaN capped AlGaN/GaN structures was also calculated by self-consistent solving the Schrödinger–Poisson equations. Comparison with the experimental measured values reveals a Fermi level pinning of the GaN (0001) surface at about 0.8 eV below the GaN conduction band.     

Neutron irradiation effects on AlGaN/GaN high electron mobility transistors

AlGaN/GaN high electron mobility transistors (HEMTs) were exposed to 1 MeV neutron irradiation at a neutron fluence of 1 × 10¹⁵ cm^-2. The dc characteristics of the devices, such as the drain saturation current and the maximum transconductance, decreased after neutron irradiation. The gate leakage currents increased obviously after neutron irradiation. However, the rf characteristics, such as the cut-off frequency and the maximum frequency, were hardly affected by neutron irradiation. The AlGaN/GaN heterojunctions have been employed for the better understanding of the degradation mechanism. It is shown in the Hall measurements and capacitance-voltage tests that the mobility and concentration of two-dimensional electron gas (2DEG) decreased after neutron irradiation. There was no evidence of the full-width at half-maximum of X-ray diffraction (XRD) rocking curve changing after irradiation, so the dislocation was not influenced by neutron irradiation. It is concluded that the point defects induced in AlGaN and GaN by neutron irradiation are the dominant mechanisms responsible for performance degradations of AlGaN/GaN HEMT devices.     

AlGaN插入层对InAlN/AlGaN/GaN异质结散射机制的影响

InAlN/AlN/GaN异质结中,名义上的AlN插入层实为Ga含量很高的AlGaN层, Al, Ga摩尔百分比决定了电子波函数与隧穿几率,因此影响与InAlN/AlGaN势垒层有关的散射机制.本文通过求解薛定谔-泊松方程与输运方程,研究了AlGaN层Al摩尔百分含量对InAlN组分不均匀导致的子带能级波动散射、导带波动散射以及合金无序散射三种散射机制的影响.结果显示:当Al含量由0增大到1,子带能级波动散射强度与合金无序散射强度先增大后减小,导带波动散射强度单调减小;在Al含量为0.1附近的小组分范围内,合金无序散射是限制迁移率的主要散射机制,该组分范围之外,子带能级波动散射是限制迁移率的主要散射机制;当Al摩尔百分含量超过0.52,三种散射机制共同限制的迁移率超过无插入层结构的迁移率, AlGaN层显示出对迁移率的提升作用.     

Characterization of GaN/AlGaN epitaxial layers grown by metalorganic chemical vapour deposition for high electron mobility transistor applications

GaN and AlGaN epitaxial layers are grown by a metalorganic chemical vapour deposition (MOCVD) system. The crystalline quality of these epitaxially grown layers is studied by different characterization techniques. PL measurements indicate band edge emission peak at 363.8 nm and 312 nm for GaN and AlGaN layers respectively. High resolution XRD (HRXRD) peaks show FWHM of 272 and 296 arcsec for the (0 0 0 2) plane of GaN and GaN in GaN/AlGaN respectively. For GaN buffer layer, the Hall mobility is 346 cm²/V-s and carrier concentration is 4.5 × 10¹⁶/cm³. AFM studies on GaN buffer layer show a dislocation density of 2 × 10⁸/cm² by wet etching in hot phosphoric acid. The refractive indices of GaN buffer layer on sapphire at 633 nm are 2.3544 and 2.1515 for TE and TM modes respectively.