Cavity ring-down spectroscopy measurements of single aerosol particle extinction. I. The effect of position of a particle within the laser beam on extinction

A continuous wave distributed feedback diode laser operating in the near infrared at wavelengths close to 1650 nm has been used to measure the extinction of light by single aerosol particles. The technique of optical feedback cavity ring-down spectroscopy (CRDS) was used for measurement of CRDS events at a repetition rate of 1.25 kHz. This very high repetition rate enabled multiple measurements of the extinction of light by single aerosol particles for the first time and demonstrated the dependence of light scattering on the position of a particle within the laser beam. A model is proposed to explain quantitatively this phenomenon. The minimum detectable dimensionless extinction coefficient epsilonmin was determined to be 3x10(-6). Extinction values obtained for single spherical polymer beads from a monodisperse sample of particles of diameter of 4 microm are in near-quantitative agreement with the values calculated by the Mie scattering theory. The deviations from the Mie theory expected for measurement of extinction by CRDS using a continuous wave laser are discussed in the companion paper.     

Efflorescence relative humidity for ammonium sulfate particles

The classical homogeneous nucleation theory was employed to calculate the efflorescence relative humidity (ERH) of airborne ammonium sulfate particles with a wide size range (8 nm to 17 microm) at room temperature. The theoretical predictions are in good agreement with the experimentally measured values. When the ammonium sulfate particle is decreased in size, the ERH first decreases, reaches a minimum around 30% for particle diameter equal to about 30 nm, and then increases. It is for the first time that the Kelvin effect is theoretically verified to substantially affect the ERH of ammonium sulfate particles smaller than 30 nm, while the aerosol size is the dominant factor affecting the efflorescent behavior of ammonium sulfate particles larger than 50 nm.     

Role of interfacial water in the heterogeneous uptake of glyoxal by mixed glycine and ammonium sulfate aerosols

This study focuses on the heterogeneous reactions of gas phase glyoxal with aerosols of glycine, the most abundant amino acid in atmospheric aerosols, as well as with a mixture of glycine and ammonium sulfate (AS) at a molar ratio of 1:100 (glycine-AS 1:100). Aerosols were exposed to varying relative humidity (RH) conditions in the presence of gas phase glyoxal for ～1 h, followed by drying and efflorescence. The changes in size, chemical composition, and optical properties were consequently measured. The reactions occur over a wide range of relative humidities, from ～30% up to 90% RH, covering values that are substantially lower as well as above the deliquescence point of the investigated aerosols. The product aerosols exhibit a trend of increasing growth in size, in optical extinction cross sections, and in extinction efficiencies (at λ = 355 nm) with decreasing seed aerosol size, and with decreasing RH values from 90% to ～50%. For glycine-AS 1:100 particles, the ratio of the geometric cross section of the product aerosol to the original seed aerosol reached a value of ～3, the optical extinction cross section ratio was up to ～25, and the Q(ext) ratio was up to ～8, exceeding those of both AS and glycine separately, suggesting a synergistic effect. Aerosol mass spectrometer analyses show that the main products of all the studied reactions are glyoxal oligomers (light scattering compounds), with a minor contribution from imidazoles (absorbing compounds at λ = 355 nm). These findings imply that the changes in the optical properties are likely due to enhanced scattering by the reaction products. The fraction of absorbing substances in the reacted aerosol increases with increasing RH, suggesting that the absorption component may become more substantial after longer reaction times, possibly in cloud or fog droplets. The results suggest that these reactions are possibly important in low RH regions, plausibly due to the reaction occurring in a few interfacial monolayers of water well before deliquescence.     

Direct comparison of the hygroscopic properties of ammonium sulfate and sodium chloride aerosol at relative humidities approaching saturation

Holographic optical tweezers are used to make comparative measurements of the hygroscopic properties of single component aqueous aerosol containing sodium chloride and ammonium sulfate over a range of relative humidity from 84% to 96%. The change in RH over the course of the experiment is monitored precisely using a sodium chloride probe droplet with accuracy better than ±0.09%. The measurements are used to assess the accuracy of thermodynamic treatments of the relationship between water activity and solute mass fraction with particular attention focused on the dilute solute limit approaching saturation vapor pressure. The consistency of the frequently used Clegg-Brimblecombe-Wexler (CBW) treatment for predicting the hygroscopic properties of sodium chloride and ammonium sulfate aerosol is confirmed. Measurements of the equilibrium size of ammonium sulfate aerosol are found to agree with predictions to within an uncertainty of ±0.2%. Given the accuracy of treating equilibrium composition, the inconsistencies highlighted in recent calibration measurements of critical supersaturations of sodium chloride and ammonium sulfate aerosol cannot be attributed to uncertainties associated with the thermodynamic predictions and must have an alternative origin. It is concluded that the CBW treatment can allow the critical supersaturation to be estimated for sodium chloride and ammonium sulfate aerosol with an accuracy of better than ±0.002% in RH. This corresponds to an uncertainty of ≤1% in the critical supersaturation for typical supersaturations of 0.2% and above. This supports the view that these systems can be used to accurately calibrate instruments that measure cloud condensation nuclei concentrations at selected supersaturations. These measurements represent the first study in which the equilibrium properties of two particles of chemically distinct composition have been compared simultaneously and directly alongside each other in the same environment.     

Production of highly dispersed sodium chloride: Strategy and experiment

Various methods for obtaining highly dispersed sodium chloride in the form of powders and sols in organic solvents were studied and compared. These include the mechanical grinding in a ball mill, laser ablation, cryochemical method, solvent-substitution method, pyrolysis of an aerosol, and a number of chemical methods. The samples obtained were examined by X-ray diffraction, elemental analysis, transmission electron microscopy, and dynamic light scattering technique. The methods for obtaining highly dispersed NaCl were compared in three basic parameters: size of particles being obtained, their size distribution, and productivity. It was shown that, depending on a method used, sodium chloride particles with average sizes in the range from 15–30 nm to 10–20 μm can be obtained.     

基质与分析物的摩尔比和激光能量对分析物离子信号的影响

A method of aerosol introduction for matrix-assisted laser desorption/ionization (MALDI) is described. The aerosol particles containing matrix and analyte enter directly into the aerosol time-of-flight mass spectrometer (ATOFMS) at atmospheric pressure. The scattered light signals from the aerosol particles are collected by a photomultiplier tube (PMT) and are passed on to an external electronic timing circuit, which determines particle size and is used to trigger a 266 nm pulsed Nd:YAG laser. The aerosol MALDI mass spectra and aerodynamic diameter of single particles can be obtained in real-time. Compared with other methods of liquid sample introduction, this method realizes detection of single particles and, more importantly, the sample consumption is lower. The effects of matrix-to-analyte ratio and laser pulse energy on analyte ion yield are examined. The optimal matrix-to-analyte ratio and laser energy are 50-110:1 and 200-400 μJ respectively.     

Absorption and scattering of light by Pt, Pd, Ag, and Au nanodisks: absolute cross sections and branching ratios

Localized surface plasmons (LSPs) of metallic nanoparticles decay either radiatively or via an electron-hole pair cascade. In this work, the authors have experimentally and theoretically explored the branching ratio of the radiative and nonradiative LSP decay channels for nanodisks of Ag, Au, Pt, and Pd, with diameters D ranging from 38 to 530 nm and height h=20 nm, supported on a fused silica substrate. The branching ratio for the two plasmon decay channels was obtained by measuring the absorption and scattering cross sections as a function of photon energy. The former was obtained from measured extinction and scattering coefficients, using an integrating sphere detector combined with particle density measurements obtained from scanning electron microscopy images of the nanoparticles. Partly angle-resolved measurements of the scattered light allowed the authors to clearly identify contributions from dipolar and higher plasmonic modes to the extinction, scattering, and absorption cross sections. Based on these experiments they find that absorption dominates the total scattering cross section in all the examined cases for small metallic nanodisks (D<100 nm). For D>100 nm absorption still dominates for Pt and Pd nanodisks, while scattering dominates for Au and Ag. A theoretical approach, where the metal disks are approximated as oblate spheroids, is used to account for the trends in the measured cross sections. The field problem is solved in the electrostatic limit. The spheroid is treated as an induced dipole for which the dipolar polarizability is calculated based on spheroid geometry and the (bulk) dielectric response function of the metal the spheroid consists of and the dielectric medium surrounding it. One might expect this model to be inappropriate for disks with D>100 nm since effects due to the retardation of the incoming field across the metallic nanodisk and contributions from higher plasmonic modes are neglected. However, this model describes quite well the energy dependence of the dipolar resonance, the full width at half maximum, and the total extinction cross section for all four metallic systems, even when 100相似文献   

Calibration of Polarization-Sensitive and Dual-Angle Laser Light Scattering Methods Using Standard Latex Particles

A polarization-sensitive laser light scattering (PSLLS) method and a dual-angle laser light scattering (DALLS) method have been studied for in situ measurement of submicrometer hydrosol and aerosol particles. By using standard monodisperse polystyrene latex particles suspended in water and air as test particles, calibration of systems built based on the above methods have been performed. The effects of light scattered by agglomerated aerosol particles (multiplets) were corrected by considering the fraction of multiplets as determined with an aerosol measurement technique using a differential mobility analyzer. The change in the measured intensities of scattered light with particle diameter was then determined by calculations based on Mie theory. It was shown that the PSLLS system can determine particle diameters as small as approximately 60 nm for the test hydrosol particles and approximately 100 nm for test aerosol particles, respectively. The DALLS system can determine smaller diameters than the PSLLS system for test particles with no light absorption. The change in scattered light intensities with particle diameter was also investigated by theoretical calculations with various refractive indexes and scattering angles. The PSLLS and DALLS systems promise to become routine measurement tools for absorbing and nonabsorbing particles, respectively. Copyright 2001 Academic Press.     

Online deposition of nano‐aerosol for matrix‐assisted laser desorption/ionization mass spectrometry

An online nano‐aerosol sample deposition method for matrix‐assisted laser desorption/ionization (MALDI) mass spectrometry is described in which matrix and analyte particles between 50 and 500 nm are aerodynamically focused onto a tight spot, ca. 200 µm in diameter, on the target plate under vacuum. MALDI analysis of the target is performed without additional sample preparation. The method is evaluated with insulin as the analyte and alpha‐cyano‐4‐hydroxycinnamic acid (CHCA) as the matrix. Two preparation modes are compared with conventional dried‐droplet deposition: mixture deposition where a single layer is deposited consisting of particles that contain both matrix and analyte, and layered deposition where an underlayer of matrix particles and an overlayer of analyte particles are deposited separately. Desalting is performed by adding ammonium sulfate to the solution used to generate the matrix aerosol. With mixture deposition, the optimum matrix‐to‐analyte mole ratio is about 500:1 compared with 5000:1 for the conventional dried‐droplet method. With layered deposition, the thicknesses of the matrix and analyte layers are more important determinants of the analyte signal intensity than the matrix‐to‐analyte mole ratio. Analyte signal intensities are independent of matrix layer thickness above 200 nm, and the optimum analyte signal is obtained with an analyte layer thickness of about 100 nm. Copyright © 2009 John Wiley & Sons, Ltd.     

Study of inorganic ammonium compounds in individual marine aerosol particles by laser microprobe mass spectrometry

Ammonia is important in the atmosphere because it neutralizes acidic species. The relative importance of different inorganic ammonium compounds (chloride, nitrate and sulfate) in marine air chemistry was studied by single-particle characterization with the laser microprobe mass analyser. Standard aerosols were generated as a reference for compound identification, based on the fingerprint spectra obtained, and calculation of the relative sensitivity achieved for different ions in a marine aerosol matrix. The relative sensitivity for ammonium was low. Aerosol samples were collected in the Southern Bight of the North Sea under different meteorological conditions and examined for their ammonium compounds. Samples collected during an inversion period with continental influences showed a much higher content in all particles than samples collected under different meteorological conditions, where ammonium was mostly detected in the submicrometer particle-size range.     

Visualization of aerosol particles generated by near infrared nano- and femtosecond laser ablation

The expansion of aerosols generated by near infrared (NIR) nanosecond (ns) and femtosecond (fs) laser ablation (LA) of metals at atmospheric pressures was explored by laser-induced scattering. In order to achieve adequate temporal and spatial resolution a pulsed laser source was utilized for illuminating a 0.5 mm-wide cross section of the expanding aerosol. It could, for instance, be shown that NIR-ns-LA under quiescent argon atmosphere provokes the formation of a dense aerosol confined within a radially propagating vortex ring. The expansion dynamics achieved under these conditions were found to be fairly slow whereas the degree of aerosol dispersion for NIR-ns-LA using helium drastically increased due to its lower viscosity. As a consequence, the maximum diameter of expansion differed by a factor of approximately four. The trajectories of aerosol particles generated by NIR-ns-LA using argon could, furthermore, be simulated on the basis of computational fluid dynamics (CFD). For this purpose, a model inspired by the thermal character of NIR-ns-LA taking into account a sudden temperature build-up of 10,000 K at the position of the laser focus was implemented.     

Absorption of scattered light in colloidal systems of aggregated particles

Scattering and extinction of colloidal systems containing either nonabsorbing or strongly absorbing spherical particles of some nanometers in diameter were examined in the wavelength range from the near UV to the near IR. If aggregation occurs, scattering and extinction are modified with respect to the single sphere systems. The influence of aggregation can best be recognized for absorbing particles when already the single sphere shows resonant extinction. In this case, the resonance of the single sphere splits into many new resonances for the aggregate, most of which are positioned at larger wavelengths than the single sphere resonance. They strongly depend on the size and shape of the aggregate.Looking at the scattering, additional problems arise in systems of absorbing particles caused by reabsorption by neighboring spheres or aggregates. A simple model was developed to interpret the obtained scattering data.     

Femtosecond study of ultrafast fluorescence resonance energy transfer in a catanionic vesicle

Ultrafast fluorescence resonance energy transfer (FRET) in a catanionic [sodium dodecyl sulfate (SDS)-dodecyltrimethyl ammonium bromide (DTAB)] vesicle is studied by femtosecond up-conversion. The vesicles (diameter ～400 nm for SDS-rich and ～250 nm for DTAB-rich vesicles) are much larger than the SDS and DTAB micelles (diameter ～4 nm). In both micelle and vesicles, FRET occurs in multiple time scales and the time scales of FRET correspond to a donor-acceptor distance varying between 12 and 36 A?.     

单颗粒气溶胶飞行时间质谱仪分析香烟烟气气溶胶

单颗粒气溶胶飞行时间质谱可同时对气溶胶单颗粒的粒径大小、化学成分进行实时、在线检测.本研究介绍了新近研制的单颗粒质谱仪的原理、结构、主要技术指标及对香烟烟气气溶胶的应用研究.仪器采用空气动力学透镜聚焦,双光束粒径测量系统确定颗粒物的空气动力学直径,激光电离系统实现颗粒物精确电离,通过双极有网反射飞行时间质量分析器实现正负离子同时检测.香烟检测结果表明,在颗粒物粒径分布上,新鲜香烟烟气颗粒范围较老化烟气宽.在气溶胶化学成分上,老化烟气颗粒物与新鲜烟气相比,尼古丁,氰酸盐,硝酸盐,硫酸盐及铵盐5种成分的数浓度百分比都有所增加,而含C1-的数浓度百分比减少.原因可能是由于烟气由气相到粒相之间的转化,及颗粒物与空气中的气体发生了非均相反应;C1-老化之后的减少是因为HN03与CI-之间的非均相反应.     

Physical properties of organic particulate UV absorbers used in sunscreens II. UV-attenuating efficiency as function of particle size

In this study the UV-attenuating properties of microparticles consisting of a benzotriazole derivative were investigated, which are used as absorbers for UV radiation in cosmetic sunscreens. The particles were micronized in presence of a dispersing agent by means of a ball milling process. According to the energy input different particle sizes were produced in the range of 0.16 to 4 microm. In order to study even smaller particles, the sample with particle size 0.16 microm was fractionated further by centrifugation. Particle sizes were measured using fiberoptic quasi-elastic light scattering (FOQELS) and laser diffractometry. The UV-attenuating properties of the dispersions with different particle sizes were assessed using UV spectroscopy. With decreasing particle size the efficiency of the UV extinction of the dispersion increases up to a particle size of 80 nm. For particles smaller than 80 nm the UV extinction decreases again indicating an optimum at 80 nm. From reflection spectroscopic measurements it was found that scattering makes about 10%, and absorption 90%, of the UV-attenuating effect of the particles, which are obtained at the end of the milling process.     

Structure and rheology of reverse micelles in dipentaerythrityl tri-(12-hydroxystearate)/oil systems

We report the formation of reverse rod-like micelles and their rheological properties in novel nonionic surfactant, dipentaerythrityl tri-(12-hydroxystearate) (designated as WO-6)/oil systems without external water addition. Small-angle X-ray scattering (SAXS) was used to investigate the structure of the micelles and their flow properties were studied by rheological measurements. We found that WO-6 spontaneously self-assembles into reverse micelles in a variety of organic solvents at ambient conditions, their structure depending on solvent molecular architecture, surfactant concentration, and temperature. Rod-like micelles with a maximum length of ca. 12 nm and a cross section diameter of ca. 2 nm were observed in cyclohexane. When cyclohexane was replaced with a linear chain octane, the length and the cross section diameter were simultaneously increased. With a further increase of hydrocarbon chain length of solvent oils from octane to hexadecane, the rod-like micelles grew axially, keeping the cross section diameter (ca. 3 nm) virtually constant. Increasing surfactant concentration also favored one-dimensional micellar growth. On the other hand, micelles shrunk with the rise of temperature, which is similar to a rod-to-sphere transition, and is essentially the opposite temperature dependence to that often observed in aqueous micellar systems. A structural picture drawn by SAXS is well supported by rheology; the relative (zero-shear) viscosity of the WO-6/oil systems was found to be markedly greater than that expected for a dispersion of spherical particles due to the elongated micellar structure, despite quantitative inconsistency with semi-empirically predicted values for rigid rod-like particles.     

纳米金刚石解团聚的一种新方法——石墨化-氧化法

用炸药爆炸法制备的纳米金刚石(ND)是由直径为4～6 nm的金刚石微晶粒组成，但这种纳米晶粒相互团聚，形成尺寸大得多的团聚体，至今尚未找到很有效的解团聚方法.该文提出了一种可用于这种纳米金刚石解团聚的新方法——石墨化－氧化法.将纳米金刚石粉在氮气中1 000 ℃加热1 h，这时纳米颗粒表面和界面上生成石墨层，再用在空气中450 ℃氧化的方法，将界面上的石墨层除去.将经过这样处理后的样品放入水中用超声波分散后，超过50％（质量百分数）的金刚石颗粒可以被分散到直径小于50 nm.可见这种方法对纳米金刚石的解团聚有一定的效果.但是同时也生成了一部分尺寸更大的团聚体，认为可能是生成了颗粒间的C-O-C键，需要进一步用适当的化学方法进行解离.对这一过程的机理进行了初步讨论.     

Detection of zinc and lead in water using evaporative preconcentration and single-particle laser-induced breakdown spectroscopy

A novel laser-induced breakdown spectroscopy (LIBS)-based measurement method for metals in water is demonstrated. In the presented technology a small amount of sodium chloride is dissolved in the sample solution before spraying the sample into a tubular oven. After water removal monodisperse dry NaCl aerosol particles are formed where trace metals are present as additives. A single-particle LIBS analysis is then triggered with a scattering based particle detection system. Benefits are the highly increased metal concentration in the LIBS focal volume and the static NaCl-matrix which can be exploited in the signal processing procedure. Emitted light from the emerged plasma plume is collected with wide angle optics and dispersed with a grating spectrometer. In an aqueous solution, the respective limits of detection for zinc and lead were 0.3 ppm and 0.1 ppm using a relatively low 14 mJ laser pulse energy. Zn/Na peak intensity ratio calibration curve for zinc concentration was also determined and LIBS signal dependence on laser pulse energy was investigated.     

Laser Microprobe Mass Analysis of Individual Antarctic Aerosol Particles

Abstract

Individual Antarctic aerosol particles in the 0.5–4 μm aerodynamic diameter range were analyzed using laser microprobe mass analysis (LAMMA). As they were sampled near the ocean, the great majority consists of seasalt, transformed to various degrees in the atmosphere. Major alterations include the association of an excess sulfate and methane sulfonate with these particles. Sulfate-rich particles containing little or no chloride were found mostly in the smallest size fraction (0.5–1 μm), where they account for some 5% of all particles: they are most likely highly transformed seasalt. Aluminosilicates, on the other hand, only appear among the coarser particles: they represent 2% of the particulates in the 2–4 μm range. The remainder of the aerosol consists of organic, Fe-rich, K-rich and Zn-rich particles. The latter groups have very low abundances: always less than 1% of the population of the impactor stage(s) onto which they were collected.