ZrV2-xPxO7固溶体的相变与热膨胀性质的研究

本文采用固相烧结法制备了ZrV2-xPxO7@=0,0．2,0．4,0．6,0．8,1）系列材料．粉末X射线衍射（XRD）分析表明,所制备材料的结构为单一立方相．应用变温拉曼光谱研究该材料相变,变温拉曼光谱研究结果表明,材料起始相变温度随着P5＋替代V5＋量的增加逐渐降低,x=0,0．4,0．8,1对应的相变温度分别为383K,363K,273K,213K．热膨胀测试结果表明：随着P替代量的增加正一负膨胀转变温度先降低后增加,x=0,0．2,0．4,0．6,0．8,1对应的正一负膨胀转变温度分别为429K,403K,372K,390K,398K和435K．本文指出了该系列材料存在两个相变过程,为设计和制备ZrV2O7基室温附近的负热膨胀材料奠定了良好的基础．     

A2( MoO4)3(A=Al,Cr,Fe)结构与相变的Raman光谱研究

用XRD、Raman光谱和DSC研究了Al2 (MoO4)3、Cr2( MoO4)3和Fe2 (MoO4)3的结构与相变.Al2(MoO4)3、Cr2 (MoO4)3和Fe2 (MoO4)3在室温下为单斜相,分别在483 K、673 K和783 K附近转变为正交相.发现MO4四面体的对称和反对称伸缩振动模的频率和相对强...     

Y_(2-x)(LiMg)_xMo_3O_(12)固溶体吸水性与热膨胀性能研究

Y2-x(LiMg)xMo3O12固溶体(x=0、0.1、0.3、0.5、0.7、0.9、1.1、1.3、1.5、1.7、1.9和2.0)采用固相法制备。当x=0时,由于严重吸水,拉曼峰宽化。随着(LiMg)掺入量的增加,拉曼峰趋于尖锐并发生劈裂,说明固溶体的吸水性得到明显的降低,结晶性能提高,变温拉曼光谱显示失水对应的温度也在降低。在900cm-1和370cm-1附近出现的新峰,与Li-O和Mg-O的振动有关。随着(LiMg)量的增加,Li-O和Mg-O的振动加强,并导致MoO4与YO6振动减弱,也可能与热膨胀系数的变化有关。     

CO_2激光烧结合成负热膨胀材料Sc_2(MO_4)_3(M=W,Mo)及其拉曼光谱

用CO2激光烧结合成了负热膨胀材料Sc2(WO4)3和Sc2(MoO4)3.实验表明,激光合成负热膨胀材料Sc2(WO4)3和Sc2(MoO4)3属于快速合成技术,合成一个样品的时间仅需几秒到十几秒,具有快速凝固的特征;X射线衍射和拉曼光谱分析表明,所合成的材料为正交相结构,且具有较高的纯度;变温拉曼光谱分析表明,所合成的材料在室温以上没有相变,但可能有微弱的吸水性;在对Sc2O3,Mo O3,WO3,Sc2(MoO4)3和Sc2(WO4)3拉曼光谱分析的基础上,给出了激光光子能量及原料和合成产物的声子能级图,分析了激光烧结合成的机理.激光光子能量转化为激发声子的能量是光热转化的主要通道,原料在熔池中反应并快速凝固形成最终产物.     

快速烧结合成Zr1-xMxW2O8(M=Hf,Sn,Y)固溶体的Raman光谱研究

首次采用快速烧结合成技术制备了Zr1-xMxW2O8 (M=Hf,Sn,Y)系列固溶体.制备的合适条件为:温度1523～1553 K,时间30 min～1 h,同传统固相反应烧结相比,该方法合成时间和能耗显著降低.XRD和Raman光谱分析表明,Zr1-xMxW2O8 (M=Hf,Sn,Y)固溶体具有α-ZrW2O8的...     

CO$lt;sub$gt;2$lt;/sub$gt;激光烧结合成负热膨胀材料Sc$lt;sub$gt;2$lt;/sub$gt;($lt;i$gt;M$lt;/i$gt;O$lt;sub$gt;4$lt;/sub$gt;)$lt;sub$gt;3$lt;/sub$gt;($lt;i$gt;M$lt;/i$gt;=W,Mo)及其拉曼光谱

用CO₂激光烧结合成了负热膨胀材料Sc₂(WO₄)₃和Sc₂(MoO₄)₃. 实验表明, 激光合成负热膨胀材料Sc₂(WO₄)₃和Sc₂(MoO₄)₃属于快速合成技术, 合成一个样品的时间仅需几秒到十几秒, 具有快速凝固的特征; X射线衍射和拉曼光谱分析表明, 所合成的材料为正交相结构, 且具有较高的纯度; 变温拉曼光谱分析表明, 所合成的材料在室温以上没有相变, 但可能有微弱的吸水性; 在对Sc₂O₃, MoO₃, WO₃, Sc₂(MoO₄)₃和Sc₂(WO₄)₃拉曼光谱分析的基础上, 给出了激光光子能量及原料和合成产物的声子能级图, 分析了激光烧结合成的机理. 激光光子能量转化为激发声子的能量是光热转化的主要通道, 原料在熔池中反应并快速凝固形成最终产物. 关键词： 负热膨胀材料 合成 激光烧结 拉曼光谱     

固溶体Fe_(2-x)Yb_xMo_3O_(12)的相变、吸水性及热膨胀性能

采用固相烧结法,以Yb2O3、MoO3、Fe3O4为原料制备了Fe2-x Ybx Mo3O12(x=0,0.2,0.4,0.6,0.8,1,1.2,1.4,1.6,1.8,2)系列固溶体,并通过X射线衍射图样、Raman光谱、热分析以及膨胀系数测试对其结构、相变、吸水性及热膨胀性能进行了研究。结果表明Fe2-x Ybx Mo3O12当x≤0.4时是单斜相,当x≥0.6时是正交相,随着x值的增加Fe2-x Ybx Mo3O12材料的相变温度逐渐降低。Fe2-x Ybx Mo3O12含有的水分子可以分为两类,一类吸附在晶体表面对晶格振动没有影响,第二类进入晶体内部对晶格振动产生较大影响,导致负膨胀性质的消失,只有完全失去水分子后才表现负热膨胀性能。     

Bi2Ti4－xTexO11的合成及相变研究

本文合成了系列Ｂｉ２Ｔｉ４－ｘＴｅｘＯ１１样品，拉曼光谱及Ｘ射线衍射谱表明该体系的相转化边界发生在ｘ＝０．５处，Ｂｉ２Ｔｅ４Ｏ１１的压致结构相变的压力为８．２ＧＰａ。本文结果证实了我们过去对Ｂｉ２Ｔｉ４Ｏ１１相变提出的机制     

Bi2Ti4－xTexO11的合成及相变研究

本文合成了系列Ｂｉ２Ｔｉ４－ｘＴｅｘＯ１１样品，拉曼光谱及Ｘ射线衍射谱表明该体系的相转化边界发生在ｘ＝０．５处，Ｂｉ２Ｔｅ４Ｏ１１的压致结构相变的压力为８．２ＧＰａ。本文结果证实了我们过去对Ｂｉ２Ｔｉ４Ｏ１１相变提出的机制     

The phase transition, hygroscopicity, and thermal expansion properties of Yb2-xAlxMo3O12

Materials with the formula Yb2-xAlxMo3O12 （x = 0.1, 0.2, 0.3, 0.4, 0.5, 0.7, 0.9, 1.0, 1.1, 1.3, 1.5, and 1.8） were synthesized and their structures, phase transitions, and hygroscopicity investigated using X-ray powder diffraction, Raman spectroscopy, and thermal analysis. It is shown that Yb2-xAlxMo3012 solid solutions crystallize in a single monoclinic phase for 1.7 〈 x 〈 2.0 and in a single orthorhombic phase for 0.0 〈 x 〈 0,4, and exhibit the characteristics of both monoclinic and orthorhombic structures outside these compositional ranges. The monoclinic to orthorhonlbic phase transition temperature of A12Mo3012 can be reduced by partial substitution of A13＋ by Yb3＋, and the Yb2-zAlxMo3012 （0.0 〈 x 〈 2.0） materials are hydrated at room temperature and contain two kinds of water species. One of these interacts strongly with and hinders the motions of the polyhedra, while the other does not. The partial substitution of A13＋ for Yb3＋ in Yb2Mo3012 decreases its hygroscopicity, and the linear thermal expansion coefficients after complete removal of water species are measured to be -9.1 x 10-6/K, -5.5 x 10-6/K, 5.74 x 10-6/K, and 9.5 x 10 6/K for Ybl.sAlo.2（MoO4）3, Yb1.6Alo.4（MoO4）3, Ybo.4All.6（Mo04）3, and Ybo.2Al1.8（MoO4）3, respectively.     

Phase transition and thermal expansion property of Cr_(2-x)Zr_(0.5x)Mg_(0.5x)Mo_3O_(12) solid solution

Compounds with the formula Cr2-xZr0.5xMg0.5xMo3O12（x = 0.0, 0.3, 0.5, 0.9, 1.3, 1.5, 1.7, 1.9） are synthesized, and the effects of Zr4＋ and Mg2＋ co-incorporation on the phase transition, thermal expansion, and Raman mode are investigated. It is found that Cr2-xZr0.5xMg0.5xMo3O12 crystallize into monoclinic structures for x 〈 1.3 and orthorhombic structures for x _〉 1.5 at room temperature. The phase transition temperature from a monoclinic to an orthorhombic structure of Cr2Mo3O12 can be reduced by the partial substitution of （ZrMg）6＋ for Cr3＋. The overall linear thermal expansion coefficient decreases with the increase of the （ZrMg）6＋ content in an orthorhombic structure sample. The co-incorporation of Zr4＋ and Mg2＋ in the lattice results in the occurrence of new Raman modes and the hardening of the symmetric vibrational modes, which are attributed to the MoO4 tetrahedra sharing comers with ZrO6/MgO6 octahedra and to the strengthening of Mo-O bonds due to less electronegativities of Zr4＋ and Mg2＋ than Cr3＋, respectively.     

Thermal expansion properties of Lu2-xFexMo3O12

The structures and thermal expansion properties of Lu2-xFexMo3O12 have been investigated by X-ray diffraction(XRD).XRD patterns at room temperature indicate that compounds Lu2-xFexMo3O12 with x≤1.3 exhibit an orthorhombic structure with space group Pnca;compounds with x=1.5 and 1.7 have a monoclinic structure with space group P21/a.Studies on thermal expansion properties show that the linear thermal expansion coefficients of orthorhombic phase vary from negative to positive with increasing Fe content.Attempts to make zero thermal expansion materials indicate that zero thermal expansion can be observed in Lu1.3Fe0.7Mo3O12 in the temperature range of 200-400℃.     

Sc2－xGaxW3O12体系负热膨胀性能研究

通过固相反应法,在1100 ℃下成功制备出了系列Ga掺杂Sc_2-xGa_xW₃O₁₂（x=0, 0.05, 0.1, 0.2, 0.3, 0.5, 0.8）固溶体.X射线粉末衍射结构精修表明,Ga以替代Sc的形式成功进入Sc_2-xGa_xW₃O₁₂晶格,但不能获得端元组分Ga₂W₃关键词： 负热膨胀 热膨胀系数 Rietveld结构精修     

Near-zero thermal expansion of In_(2(1-x))(HfMg)_xMo_3O_(12) with tailored phase transition

Solid solutions of In_(2(1-x)(HfMg)_xMo_3O_(12) are synthesized by solid state reaction with the aim to reduce the phase transition temperature of In_2Mo_3O_(12) and improve its thermal expansion property.The effects of(HfMg)~(6+) incorporation on the phase transition and thermal expansion are investigated.It is shown that the monoclinic-to-orthorhombic phase transition temperature obviously decreases and the coefficient of thermal expansion(CTE) of the orthorhombic becomes less negative and approaches to zero with increasing the content of(HfMg)~(6+).A near zero thermal expansion covering the case at room temperature(RT) is achieved for the solid solutions with x ≥ 0.85,implying potential applications of this material in many fields.     

Zero and controllable thermal expansion in HfMgMo_(3-x)W_xO_(12)

HfMgMo_(3-x)W_xO_(12) with x = 0.5, 1.0, 1.5, 2.0, and 2.5 are developed with a simple solid state method. With increasing the content of W, solid solutions of Hf Mg Mo3-xWx O12 crystallize in an orthorhombic structure for x≤2.0 and a monoclinic structure for x2.0. A near-zero thermal expansion(ZTE) is realized for HfMgMo_(2.5)W_(0.5)O_(12) and negative coefficients of thermal expansion(NCTE) are achieved for other compositions with different values. The ZTE and variation of NCTE are attributed to the difference in electronegativity between W and Mo and incorporation of a different amount of W, which cause variable distortion of the octahedra and softening of the MoO_4 tetrahedra, and hence an enhanced NCTE in the a- and c-axis and reduced CTE in the b-axis as revealed by Raman spectroscopy and x-ray diffraction.     

正交相Fe2(MoO4)3的制备与表征及其负膨胀行为的第一性原理研究

采用水热合成法制备出Fe₂(MoO₄)₃样品, 并用高温X-射线衍射、热重和差示扫描量热同步热分析仪对其进行表征, 发现样品在510 ℃附近发生低温单斜相和高温正交相之间的可逆相变, 且正交相表现出负膨胀特征. 采用第一性原理计算了正交相Fe₂(MoO₄)₃ 的原子、电子结构以及声子谱、声子态密度, 并和可获得的实验结果进行了系统的比较. 结果显示正交相Fe₂(MoO₄)₃中MoO₄四面体较之FeO₆八面体具有更强的刚性. 发现最低频的光学支处具有最负的格林乃森(Grüneisen)系数, MoO₄四面体和FeO₆ 八面体相连的桥氧原子的横向振动、FeO₆八面体柔性扭曲转动以及MoO₄四面体的刚性翻转共同导致了Fe₂(MoO₄)₃负膨胀现象的发生.