Liquid crystal alignment properties on surface-reformed solution-derived lanthanum-doped zinc oxide films

Liquid crystal (LC) alignment characteristics were investigated using a solution-derived lanthanum-doped zinc oxide (La:ZnO) film that was exposed to various intensities of ion-beam (IB) irradiation. At an IB intensity of 1700 eV, uniform and homogeneous LC alignment was achieved, as revealed by cross-polarized optical microscopy and pre-tilt angle measurement. Field-emission scanning electron microscopy (FE-SEM), atomic force microscopy (AFM), and X-ray photoelectron spectroscopy (XPS) were used to verify that the IB irradiation induced physical and chemical surface reformation of the La:ZnO film that relate to LC alignment. FE-SEM and AFM revealed that the IB irradiation reformed the existing surface structure into a new structure with an altered surface roughness. The XPS results showed that the van der Waals force with anchoring energy increased as the IB intensity increased, and this profoundly affected the state of LC alignment. The capacitance-voltage (C-V) hysteresis curve was measured as a function of IB intensity to characterize the accumulated charge as a residual DC. Nearly zero C-V hysteresis was achieved at an IB intensity of 1700 eV. Therefore, a solution-derived La:ZnO film with an IB intensity of 1700 eV has great potential for high-quality LC applications.     

Liquid crystal alignment on ion-beam irradiated bismuth-doped tin oxide films and their application to liquid crystal displays

Uniform and defect-free homogeneous alignment of liquid crystal (LC) molecules on solution-derived bismuth-doped tin oxide (TBO) films has been achieved using ion-beam (IB) irradiation. We performed measurements and physicochemical analysis to verify and establish the cause of the successful LC alignment. In addition, we measured the electro-optical characteristics of twisted-nematic cells with IB-irradiated TBO films to explore the suitability of this material for liquid crystal displays (LCDs). The results indicate that this approach will allow the fabrication of high-performance enhanced LCD devices.     

Homogeneous liquid crystal alignment on poly(vinylidene fluoride-trifluoroethylene) films subjected to ion-beam irradiation

We demonstrate homogeneous and uniform liquid crystal (LC) alignment on poly(vinylidene fluoride-trifluoroethylene) [PVDF-TrFE] films using ion-beam (IB) irradiation and a performance improvement of twisted nematic (TN) cells using IB-irradiated PVDF-TrFE films. Spontaneous ferroelectricity of the PVDF-TrFE films was modified by IB irradiation, which affected the LC alignment properties. The variation in the pre-tilt angles of the LC molecules on the IB-irradiated PVDF films is attributed to surface reformation, including defluorination and oxidation because the pre-tilt angles of LC molecules can be controlled by adjusting the fluorine content. The results of contact angle measurements supported this phenomenon. A 58% reduction in the switching voltage was observed for TN cells, indicating that the IB-irradiated PVDF-TrFE films are a promising candidate for use as an alignment layer.     

Homogeneous alignment of liquid crystals on low-temperature solution-derived gallium oxide films via IB irradiation method

In this paper, solution-derived gallium oxide (GaO) films are fabricated for the homogeneous alignment of liquid crystals (LCs) after an ion-beam (IB) irradiation process. GaO thin films are prepared under a variety of temperatures and different IB irradiation intensities, and the physicochemical performances of the fabricated GaO thin films are analysed using a UV-vis spectrometer, an atomic force microscope, and X-ray photoelectron spectroscopy. A higher transmittance of 85.40% from GaO thin film is obtained compared with that of polyimide (PI) film (83.52%), which indicates the feasibility for a GaO thin layer to substitute for a conventional PI layer as an alignment layer. LCs are found to align on the GaO thin film after pre-baking at 100°C and homogeneous and uniform low-IB intensity irradiation. We also determined the electro-optical (EO) characteristics of the twisted nematic (TN) cells fabricated with GaO thin layers and found them to be similar to those of cells fabricated with PI layers. Overall, GaO films achieved via the IB irradiation method are promising LC alignment layers due to the method’s low-temperature solution-derived process.     

Electrochemically induced growth of zinc oxide.

The electrolytically induced precipitation of zinc oxide from zinc nitrate solution on gold surfaces in the presence of water-soluble polymers was examined for reaction times between 0.5 and 600 seconds. Regardless of the additive, polycrystalline films of zinc oxide have formed after 30 seconds, but polymeric additives dramatically change the morphology of the ZnO films. Amperometric analysis and fitting the diffusion reduced the current density-time curve according to Avrami kinetics and it reveals that polymers bearing methacrylic acid groups result in spherical growth whereas such with sulfonic acid groups lead to a platelike growth of crystallites. Without additive prisms grow predominantly in one dimension. These findings are confirmed also by scanning electron microscopy (SEM) and X-ray diffraction (XRD) analysis.     

Nanostructural properties of zinc oxide thin films grown on non‐planar substrates

The crystallographic structure of zinc oxide thin films grown on optical fibres using single source chemical vapour deposition (SSCVD) was analysed using near edge X‐ray absorption fine structure (NEXAFS). Zinc diethyl carbamate was used as a precursor for the growth of highly conformal films in a one‐step deposition process without substrate rotation and at substrate temperatures of 400–575 °C. It was found that the growth temperatures greatly affected the crystallographic structure of the film with no preferred crystallographic orientation and negligible crystallinity at low temperatures and very high crystallinity with pure c‐axis orientation at high temperatures. Cross‐sectional analysis of the films by scanning electron microscopy (SEM) showed the presence of a film at all points around the fibre. These films generally consisted of densely packed columns that bore a strong resemblance to c‐axis‐oriented films grown on planar substrates. Copyright © 2005 John Wiley & Sons, Ltd.     

Synthesis and structure analysis of aluminum doped zinc oxide powders

Hexagonal Al-doped zinc oxide (ZnO) powders with a nominal composition of Zn1-xAlxO (0≤x≤0.028) were synthesized by the co-precipitation method. The contents of the Al element in the samples were measured by the inductively coupled plasma-optical emission spectroscopy (ICP-OES) technique. The structures of the Zn1-xAlxO (0≤x≤0.028) compounds calcined at 1000 and 1200℃ have been deter- mined using the Rietveld full-profile analysis method. Rietveld refinements of the diffraction data indi- cated that the addition of Al initially has a considerably positive effect on the decreasing of the lattice parameters a and c of Zn1-xAlxO, but the effect becomes very slight and even negative with the further increase of the Al content. The solid solubility limit of Al in ZnO (mole fraction y) is 2.2l%, resulting in Zn0.978Al0.22O. It seems that when the Al content is excessive, Al prefers to form a ZnAl2O4 compound with ZnO, but not to incorporate into the ZnO lattice to occupy the Zn2 cites. Two phases, [ZnO] (or Al-doped ZnO) and [ZnAl2O4], are obviously segregated in Zn1-xAlxO while the value of x is larger than 0.024. The UV-Vis absorption spectra show that the Al-doped ZnO exhibits a red-shift in the absorption edge without reduced transmission compared with pure ZnO, which also confirms that Al ions enter the ZnO lattice and form a Zn1-xAlxO solid solution.     

Vertical alignment of liquid crystal on tocopherol-substituted polystyrene films

We synthesised a series of vitamin-based and renewable tocopherol-substituted polystyrene (PTOC#, # = 20, 40, 60, 80 and 100), where # is the molar content of tocopherol moiety, using polymer analogous reactions to investigate their liquid crystal (LC) alignment properties. In general, the LC cell fabricated using the polymer film having a higher molar content of tocopherol side group showed vertical LC alignment behaviour. The vertical alignment (VA) behaviour was well correlated with the surface energy value of these polymer films. For example, VA was observed when the surface energy values of the polymer were smaller than about 35.22 mJ/m² generated by the nonpolar tocopherol moiety having long and bulky carbon groups. Good electro-optical characteristics, such as voltage holding ratio and residual DC voltage, and aligning stabilities at 200°C and ultraviolet irradiation of 10 J/cm² were observed for the LC cells fabricated using PTOC100 as a LC alignment layer. Therefore, it was first found that the renewable tocopherol-based materials can produce an eco-friendly vertical LC alignment system.     

纳米氧化锌的研究进展

本文对纳米氧化锌的制备技术进行了全面介绍并客观地指出其优缺点，概括了常用的表征方法，着重对纳米氧化锌的应用与研究前沿作了系统的阐述，并展望了纳米氧化锌的应用前景。     

Influence of oxygen flow rate on the surface chemistry and morphology of radio frequency (RF) magnetron sputtered zinc oxide thin films

Zinc oxide thin films were deposited, by radio frequency magnetron sputtering, on heated and unheated substrates. The oxygen flow rate was varied during deposition, and its effects on the structural and chemical properties of the films were investigated. The films had oriented c‐axis growth with nano‐crystallite size. Their surfaces manifested columnar microstructure, with a surface roughness that was suppressed by the introduction of oxygen. Chemical analysis showed that deposition under an oxygen atmosphere resulted in substantial reduction of oxygen vacancies, with a corresponding incorporation of chemisorbed species. Copyright © 2013 John Wiley & Sons, Ltd.     

An innovative technique based on voltammetric profiling and current–voltage characteristics for determination of residual direct-current voltage of liquid crystal cells

ABSTRACT

Generation of residual direct-current (DC) voltage (V_rDC) induces a serious image sticking of liquid crystal displays (LCDs). In this study, an innovative technique to determine the V_rDC of LC cells was proposed from the current-voltage (I-V) curves obtained by application of triangular voltage. The I-V curve shows the maximum and minimum current peaks due to the rotation of the LC director, and the V_rDC is determined from the average value of the two peaks. The V_rDC values determined from the proposed technique corresponded to the values determined from the flicker minimisation, which is the well-known method to determine the V_rDC. The results indicate that the proposed technique is useful for evaluation of the image sticking of the LCDs.     

Influence of pyrolysis temperature on the properties of sol–gel derived zinc oxide films

The influence of pyrolysis temperature on the properties of sol–gel derived zinc oxide films has been investigated. As-deposited films were pyrolyzed at 300 °C for 30 min and at 500 °C for 10 min. Final annealing was done at 600 °C for 30 min in air. The as-grown films deposited on soda-lime-silica glass substrates were highly c-axis oriented. Distinct grain structure was present in the film pyrolyzed at 500 °C, while the surface of the film pyrolyzed at 300 °C was smooth and no observed texture. The surface of ZnO pyrolyzed at 300 °C was covered with needle-like grain growth. With increasing pyrolysis temperature at 500 °C, a three-dimensional island formation was appeared.     

Effect of water vapor on the thermal decomposition process of zinc hydroxide chloride and crystal growth of zinc oxide

Thermal decomposition process of zinc hydroxide chloride (ZHC), Zn₅(OH)₈Cl₂·H₂O, prepared by a hydrothermal slow-cooling method has been investigated by simultaneous X-ray diffractometry and differential scanning calorimetry (XRD-DSC) and thermogravimetric-differential thermal analysis (TG-DTA) in a humidity-controlled atmosphere. ZHC was decomposed to ZnO through β-Zn(OH)Cl as the intermediate phase, leaving amorphous hydrated ZnCl₂. In humid N₂ with P_H2O=4.5 and 10 kPa, the hydrolysis of residual ZnCl₂ was accelerated and the theoretical amount of ZnO was obtained at lower temperatures than in dry N₂, whereas significant weight loss was caused by vaporization of residual ZnCl₂ in dry N₂. ZnO formed by calcinations in a stagnant air atmosphere had the same morphology of the original ZHC crystals and consisted of the c-axis oriented column-like particle arrays. On the other hand, preferred orientation of ZnO was inhibited in the case of calcinations in 100% water vapor. A detailed thermal decomposition process of ZHC and the effect of water vapor on the crystal growth of ZnO are discussed.     

Research of protein adsorption on the different surface topography of the zinc oxide

The effect of the surface topography on the protein adsorption process is of great significance for designing biomaterial surfaces and the biocompatibility for specific biomedical applications. In this work, we have systematically investigated the mono‐protein adsorption kinetics of bovine serum albumin (BSA) and fibrinogen (Fg) adsorbed on the four different surface topographies (nanoparticles (NPs), nanorods (NRs), nanosheets (NSs) and nanobeams (NBs) of Zinc oxide (ZnO), respectively. The competition of multi‐protein adsorbed on them has been studied as well. Results showed that each protein had a singular process of adsorption that fitted well by Spreading Particle Model (SPM). It confirmed that ZnO NRs compared with other samples had more adsorption sites, which could provide more opportunities for the interaction between material and protein molecules. In addition, the Fg compared to the BSA could be more tightly adsorbed to the surface, both of which existed slight conformational changes by Fourier transform infrared (FTIR) and circular dichroism spectra (CD). Taken together, all these consequences well demonstrated that NRs may have wider applications in designing biomaterial surfaces and the biocompatibility for implanted biomaterials. Copyright © 2014 John Wiley & Sons, Ltd.