碳纳米管复合聚对氨基吡啶修饰电极伏安法同时测定硝基酚异构体的研究

利用导电聚合物的分子识别性和碳纳米管奇特的物理化学性质, 制备了碳纳米管复合聚对氨基吡啶(SWNTs/POAP)修饰电极, 研究了邻、间、对硝基酚异构体同时在该电极上的电化学响应. 实验结果表明, 邻、间、对硝基酚异构体在SWNTs/POAP纳米电极界面具有不同的构象, 其氧化峰电位能够完全分开, 并能显著地提高电化学测定的灵敏度. 文中的SWNTs/POAP纳米电极制备简单方便, 可用于硝基酚位置异构体的同时电化学量测.     

邻溴苯甲酸电化学脱溴反应的原位红外光谱研究

采用循环伏安法研究了水溶液中邻溴苯甲酸在不同电极上的电化学还原脱溴反应,与Ti和C电极相比,Cu电极对邻溴苯甲酸有较好的电化学还原活性。同时采用电化学原位红外反射光谱对其反应机理进行了系统分析,结果表明：邻溴苯甲酸在Cu电极上的电还原脱溴反应是一个脱溴加氢的过程,邻溴苯甲酸在电极表面首先得到一个电子变成邻溴苯甲酸自由基负离子;然后脱去溴离子得到苯甲酸自由基,该自由基再得到一个电子变成苯甲酸负离子;最后加成氢质子得到最终产物苯甲酸,这一产物已经通过恒电流电解实验得到了进一步的证实。     

碳纳米管复合聚合物电极的构建及对色氨酸和5-羟基色氨酸的同时电化学测定

以镍铬合金为基体,首先通过嵌压技术在其表面置入厚度约为100 nm的碳糊前驱膜,然后结合SWNTs和聚合物膜的特性,构建了单壁碳纳米管复合聚对氨基苯甲酸修饰的嵌入式超薄碳糊电极(SWNTs/PABAE).SWNTs/PABAE改变了基体材料的电化学性质,使其可用作电化学研究电极,并用于色氨酸(Trp)和5-羟基色氨酸(5-HTP)的同时电化学行为研究,获得满意的结果.     

复合修饰电极测定p-硝基苯酚新方法的研究与探讨

将多壁碳纳米管分散在孔雀绿溶液中并滴涂在玻碳电极表面,再电聚合一层孔雀绿膜,制备了一种新型的聚孔雀绿/多壁碳纳米管复合膜修饰玻碳电极.用电化学方法对所制得的复合修饰电极进行了表征,并研究了p-硝基苯酚在该电极上的电化学行为.结果表明,所制备的复合修饰电极对P-硝基苯酚有良好的电催化作用,从而建立了一种直接测定P-硝基苯...     

纳米晶碳化钨薄膜对硝基甲烷还原的电催化性能

采用磁控溅射物理气相沉积技术在金属镍基体上制备碳化钨纳米晶薄膜. 薄膜具有纳米晶结构, 由粒径为20~35 nm的晶粒构成, 晶粒分布均匀, 晶相结构为非化学计量比的碳化钨(WC1-x). 采用电化学方法研究硝基甲烷在纳米晶碳化钨薄膜电极上的电化学还原性能和反应机理. 实验结果表明, 碳化钨薄膜电极对硝基甲烷电化学还原反应具有较好的催化性能, 当电极电位为-0.89 V(vs.SCE)时, 硝基甲烷还原为甲基羟胺的电流达14.9 mA/cm2, 其反应表观活化能为12.3 kJ/mol. 硝基甲烷在碳化钨薄膜电极上经过一步不可逆的电化学反应还原成甲基羟胺, 其控制步骤是电极反应的电荷传递过程.      

邻碘苯甲酸电还原脱碘的原位红外光谱研究

采用循环伏安法研究了邻碘苯甲酸在NaOH溶液中的电化学还原反应,与Pt和Ti等电极相比,Ag和Cu电极对邻碘苯甲酸具有较好的电还原活性,还原电位向正电位方向移动.通过原位红外光谱技术研究了邻碘苯甲酸在Ag和Cu电极上的电还原机理.结果表明,在电位高于-800 mV时,邻碘苯甲酸在Ag电极表面先形成吸附中间态R…I…Ag,而在Cu电极表面以负离子形式存在.随着电位的进一步负移,邻碘苯甲酸在Ag和Cu电极上均发生脱碘加氢反应,经还原得到最终产物苯甲酸.     

聚邻氨基苯甲酸-铜复合薄膜修饰电极的制备及其电化学性能

利用聚合物官能团对金属离子的配位作用,在电极表面原位制备了金属粒子。 首先在玻碳电极（GCE）表面电沉积聚邻氨基苯甲酸(PoABA),再化学吸附铜离子(Cu2+),用水合肼还原得到单质铜(Cu0)。 采用扫描电子显微镜和能谱分析表征了聚邻氨基苯甲酸 铜(PoABA-Cu0)复合薄膜的表面形貌和元素构成,研究了PoABA-Cu0修饰电极的电化学性能,并以其检测了过氧化氢（H2O2）。 结果表明,电极表面被修饰上了一层PoABA-Cu0复合薄膜;制备的修饰电极对H2O2具有良好的电催化性能,在邻氨基苯甲酸的聚合圈数为10、Cu2+的吸附时间为10 min、工作电压为-0.3 V时,该修饰电极对H2O2表现出了最佳的检测性能,其线性浓度范围为5.0×10-5～1.0×10-2 mol/L,灵敏度为96.3 μA·L/(mmol·cm),检测限为5.0×10-5 mol/L,且具有较好的稳定性。     

3-硝基苯甲酸在DMSO介质中的电化学还原

本文用循环伏安法、控制电位电解和ESR方法结合, 研究了3-硝基苯甲酸(3-NBA)在DMSO介质中, Pt电极上的电化学还原过程。结果表明, 3-硝基苯甲酸通过三电子还原生成一种亚硝基自由基。观测到了自由基ESR谱的超精细结构。确定了ESR模拟谱的参数: a_1~N=10.91G, a_2~H=1.12G, a_4~H=a_6~H=3.38G, a_5~H=3.96G. 估算了自由基衰变速度常数k=4.814×10~(-2)s~(-1).     

壳聚糖复合碳纳米管修饰超薄碳糊电极对硝基酚异构体的同时测定

以镍镉合金为基底,将壳聚糖滴涂在碳纳米管修饰的超薄碳糊电极表面制成电化学传感器(CTSCNTs-UTCPE),利用循环伏安法(CV)、半微分伏安法研究硝基酚异构体在该电极上的电化学行为。考察了底液种类、酸碱度、扫描速度、起始电位和富集时间对检测结果的影响。与镍铬合金电极、超薄碳糊电极(UTCPE)和碳纳米管修饰超薄碳糊电极(CNTs-UTCPE)相比,由于壳聚糖和碳纳米管的协同效应,硝基酚异构体在p H 5.72的B-R中氧化电流较高。在最佳条件下,传感器对邻、间、对硝基酚的检测范围分别为4.0×10-7~8.0×10-5mol/L,4.0×10-7~8.0×10-5mol/L,8.0×10-7~8.0×10-5mol/L;检出限(S/N=3)分别为2.3×10-7,2.9×10-7,6.7×10-7mol/L。该传感器显示出良好的稳定性和抗干扰性能,可实现对人工水样中硝基酚异构体的同时检测。     

苯甲酸在疏水性复合电极上的电化学还原行为

以铜片和锌片为基材,复合电镀制得Cu-PTFE(聚四氟乙烯)和Zn-PTFE疏水性复合电极,并将复合电极应用于苯甲酸的电化学还原行为研究。测定了复合电极在电解液中的Tafel极化曲线、循环伏安、电极稳定性和交流阻抗等电化学参数。结果表明,在苯甲酸电还原制备苯甲醛中,Cu-PTFE复合电极相对于Zn-PTFE复合电极具有较高的催化活性,其电还原产率分别为88.4%和79.2%,因此,Cu-PTFE复合电极有望成为苯甲酸电化学还原制备苯甲醛的电极材料。电化学行为的研究结果显示,苯甲酸在疏水性复合电极上的电还原过程可能只受电子迁移过程控制。     

Fabrication,Characterization, and Application of ‘Sandwich‐Type’ Electrode Based on Single‐Walled Carbon Nanotubes and Room Temperature Ionic Liquid

The much‐enhanced electrochemical responses of potassium ferricyanide and methylene blue (MB) were firstly explored at the glassy carbon electrode modified with single‐walled carbon nanotubes (SWNT/GCE), indicating the distinct electrochemical activity of SWNTs towards electroactive molecules. A hydrophobic room temperature ionic liquid (RTIL), 1‐butyl‐3‐methylimidazolium hexafluorophosphate (BMIMPF₆), was used as electrode modification material, which presented wide electrochemical windows, proton permeation and selective extraction ability. In consideration with the advantages of SWNTs and RTIL in detecting target molecules (TMs), a novel strategy of ‘sandwich–type’ electrode was established with TMs confined by RTIL between the SWNT/GCE and the RTIL membrane. The strategy was used for electrochemical detection of ascorbic acid (AA) and dopamine (DA), and detection limits of 400 and 80 fmol could be obtained, respectively. The selective detection of DA in the presence of high amount of AA could also be realized. This protocol presented many attractive advantages towards voltammetric detection of TMs, such as low sample demand, low cost, high sensitivity, and good stability.     

Effect of electrode surface microstructure on electron transfer induced conformation changes in cytochrome c monitored by in situ UV and CD spectroelectrochemistry

Electrochemical redox processes of bovine heart cytochrome c were investigated by in situ UV-vis and CD spectroelectrochemistry at bare glassy carbon electrode (GCE) and single-wall carbon nanotubes (SWNTs) modified glassy carbon electrode (SWNTs/GCE) using a long optical path thin layer cell. The spectra obtained at GCE and SWNTs/GCE reflect electrode surface microstructure-dependent changes in protein conformation during redox transition. Potential-dependent conformational distribution curves of cytochrome c obtained by analysis of in situ circular dichroism (CD) spectra using singular value decomposition least square (SVDLS) method show that SWNTs can retain conformation of cytochrome c. Some parameters of the electrochemical reduction process, i.e. the product of electron transfer coefficient and number of electrons (alpha n = 0.3), apparent formal potential (E0' = 0.04 V), were obtained by double logarithmic analysis and standard heterogeneous electron transfer rate constant k0 was obtained by electrochemistry and double logarithmic analysis, respectively.     

Sensitive detection of trifluoperazine using a poly-ABSA/SWNTs film-modified glassy carbon electrode

A poly-ABSA/SWNTs composite-modified electrode was fabricated by electropolymerizing aminobenzene sulphonic acid (ABSA) on the surface of glassy carbon electrode (GCE) modified with single-wall carbon nanotubes (SWNTs). SWNTs provide a 3D porous and conductive network for the polymer immobilization. The nanocomposite film was characterized by scanning electron microscope (SEM) and electrochemical impedance spectroscopy (EIS). The results indicated that this composite-modified electrode had strong electrocatalytic activity toward the oxidation of trifluoperazine (TFP). TFP could effectively accumulate on the modified electrode and generate a sensitive anodic peak at 0.72V (versus SCE) in pH 6.1 phosphate buffer solution. Under the selected conditions, the anodic peak current of TFP was linear with its concentration within the range from 1.0x10(-7) to 1.0x10(-5)molL(-1) and 1.0x10(-5) to 1.0x10(-4)molL(-1), and the detection limit was 1.0x10(-9)molL(-1) (S/N=3). This method was successfully applied to the detection of trifluoperazine in drug samples and the recovery was satisfactory. In comparison with the SWNTs/GCE or poly-ABSA/GCE prepared in the similar way, this composite-modified electrode exhibited better catalytic activity.     

Covalent immobilization of single-walled carbon nanotubes and single-stranded deoxyribonucleic acid nanocomposites on glassy carbon electrode: Preparation, characterization, and applications

Single-stranded deoxyribonucleic acid (ssDNA)-wrapped single-walled carbon nanotubes (SWNTs) were modified on the surface of glassy carbon electrode (GCE) by covalent modification technique. Field emission scanning electron microscope (FE-SEM), X-ray photoelectron spectrum (XPS), electrochemical impedance spectroscopy (EIS), and cyclic voltammetric (CV) were used to characterize the properties of this modified electrode. The results showed that SWNTs-ssDNA composites were successfully immobilized onto the surface of GCE. Moreover, this modified electrode exhibited high stability, largely active areas, and efficiently electrocatalytic activities. It had been used for the analysis of various biomolecules, such as dopamine (DA), uric acid (UA), and ascorbic acid (AA), and the results were satisfactory.     

酵母核糖核酸在碳纳米管修饰电极上的电化学行为及其分析测定

研究了酵母核糖核酸（yRNA）在碳纳米管（MWNT）修饰电极上的电化学行为，优化了测定参数，在此基础上建立了一种直接测定yRNA的电分析测试方法。yRNA在碳纳米管修饰电极上于磷酸盐缓冲溶液中在0．758V处产生不可逆的氧化电流峰，峰电流与yRNA的质量浓度在1～10mg／mL之间有良好的线性关系，线性回归方程为：Iρ=0．0813ρ＋0．1807，相关系数r为0．9980，检出限为0．6mg／mL。     

Determination of Uric Acid and Norepinephrine by Chitosan‐Multiwall Carbon Nanotube Modified Electrode

A novel chemically modified electrode based on the chitosan‐multiwall carbon nanotube (MWNT) coated glassy carbon electrode (GCE) is described, which exhibited an attractive ability to determine uric acid (UA) and norepinephrine (NE) simultaneously. The responses of UA and NE merged into a large peak at a bare GCE, but yielded two well‐defined oxidation peaks at the chitosan‐MWNT modified GCE (MC/GCE). The experimental parameters were optimized, and a direct electrochemical method for the simultaneous determine for UA and NE is proposed. The MC/GCE showed good sensitivity, selectivity and stability.     

基于单壁碳纳米管-DNA酶复合结构的电化学生物传感器

结合DNA酶优异的氧化还原催化特性和碳纳米管的电化学特性, 制备了单壁碳纳米管-DNA酶复合材料, 并通过壳聚糖将其固定到玻碳电极表面构建了电化学生物传感界面. 研究了单壁碳纳米管-DNA酶复合结构的氧化还原反应催化特性, 并以此为传感平台构建了葡萄糖氧化酶电化学生物传感器. 结果表明, 单壁碳纳米管-DNA酶复合材料修饰的电极对过氧化氢的响应具有较宽的线性范围(5×10^-6~1×10^-2 mol/L)和良好的检测灵敏度(检出限为1×10^-6 mol/L). 采用制备的葡萄糖氧化酶传感器实现了对葡萄糖的快速灵敏检测.     

The influence of cetyltrimethyl ammonium bromide on electrochemical properties of thyroxine reduction at carbon nanotubes modified electrode

The effect of cetyltrimethyl ammonium bromide (CTAB) on the electrochemical behaviors of thyroxine at a glassy carbon electrode (GCE) modified with single-walled carbon nanotubes (SWNTs) was investigated. At the SWNTs film-coated GCE, a well-defined oxidation peak of thyroxine at 0.78 V was obtained, but the reduction peak of thyroxine was indiscernible. When trace CTAB was added to the working solution, the reduction current could be greatly enhanced and the oxidation current remained stable. The reaction mechanisms for the reduction of thyroxine were explored by chronocoulometry. Thyroxine might form particular ion complex with CTAB via the interaction between iodine atoms on thyroxine and bromide ions in CTAB, which made the concentration of thyroxine at the surface of the modified electrode increased and the electron transfer rate enhanced. The proper mechanisms for the enhanced reduction of thyroxine in the present of CTAB were explored by several electrochemical techniques including cycle voltammetry linear sweep voltammetry and others. It was concluded that the special interactions between the thyroxine CTAB and SWNTs resulted in the increase of the reduction peak current. All results indicated that two iodine atoms on the thyroxine and four electrons were involved the reduction process which was irreversible and two iodine ions produced. In this system, the sensitive reduction peak of thyroxine at 0.3 V was employed to determine thyroxine and a low detection limit of 2x10(-8) mol/L was obtained for 2 min accumulation at 0.9 V. The SWNTs coated GCE had good stability and reproducibility.     

Voltammetric determination of tinidazole using a glassy carbon electrode modified with single-wall carbon nanotubes.

An electrochemical method based on a single-wall carbon nanotubes (SWNTs) film-coated glassy carbon electrode (GCE) was described for the determination of tinidazole. In a 0.1 M Britton-Robinson buffer with a pH of 10.0, tinidazole yields a very sensitive and well-defined reduction peak at -0.78 V (vs. SCE) on a SWNTs-modified GCE. Compared with that on a bare GCE, the reduction peak of tinidazole increases significantly on the modified GCE. Thus, all of the experimental parameters were optimized and a sensitive voltammetric method is proposed for tinidazole determination. It is found that the reduction peak current is proportional to the concentration of tinidazole over the range from 5 x 10(-8) to 4 x 10(-5) M, and that the detection limit is 1 x 10(-8) M at 3 min open-circuit accumulation. This new analysis method was demonstrated with tinidazole drugs.     

用稀土(镱)杂多酸盐/多壁碳纳米管修饰的玻碳电极测定亚硝酸根

将多壁碳纳米管分散在镱(Ⅲ)杂多酸盐溶液中,将上述获得的悬浊液滴涂在玻碳电极表面,制备了镱(Ⅲ)杂多酸盐/多壁碳纳米管修饰的玻碳电极(YbHS-MWCNT′s/GCE)。采用交流阻抗法对电极表面的性能进行了表征,采用循环伏安法对其电化学性能进行研究。研究发现,亚硝酸根在该修饰电极上出现一个氧化峰,氧化峰电位在-0.45V处,提出了用循环伏安法测定亚硝酸根的方法。亚硝酸根的浓度在5.0×10-6～1.0×10-4mol.L-1范围内,氧化峰电流与其浓度呈线性关系。修饰电极用于环境水样中亚硝酸根离子的测定,回收率在97.2%～98.0%之间。