Laser imaging system for determination of three-dimensional scalar gradients in turbulent flames

An imaging system for the measurement of three-dimensional (3D) scalar gradients in turbulent hydrocarbon flames is described. Combined line imaging of Raman scattering, Rayleigh scattering, and CO laser-induced fluorescence (LIF) allows for simultaneous single-shot line measurements of major species, temperature, mixture fraction, and a one-dimensional surrogate of scalar dissipation rate in hydrocarbon flames, while simultaneous use of two crossed, planar LIF measurements of OH allows for determination of instantaneous flame orientation. In this manner the full 3D scalar dissipation can be estimated in some regions of a turbulent flame on a single-shot basis.     

Attenuation corrections for in-cylinder NO LIF measurements in a heavy-duty Diesel engine

Quantification of the nitric oxide (NO) concentration inside the cylinder of a Diesel engine by means of laser-induced fluorescence (LIF) measurements requires, amongst others, knowledge of the attenuation of the ultraviolet radiation involved. We present a number of laser diagnostic techniques to assess this attenuation, enabling a correction for laser intensity and detection efficiency of the raw NO LIF data. Methods discussed include overall laser beam transmission, bidirectional laser scattering (bidirectional LIF), spectrally resolved fluorescence imaging, and Raman scattering by N₂. A combination of techniques is necessary to obtain the complete attenuation of laser beam and NO fluorescence. The overall laser beam transmission measurements and bidirectional LIF measurements (the latter yielding spatially resolved transmission) provide evidence of a non-uniform attenuation distribution, with predominant attenuation within or near the piston bowl. Fluorescence imaging of multiple vibrational bands through a spectrograph is shown to be a powerful method for obtaining spatially resolved data on the transmission losses of fluorescence. Special attention is paid to the role of CO₂ and O₂ as UV light absorbers, and the consequences to different excitation-detection schemes for NO. PACS 82.33.Vx; 42.62.Fi; 33.20.t     

Measurement of water film thickness by laser-induced fluorescence and Raman imaging

We present two non-intrusive, laser-based imaging techniques for the quantitative measurement of water fluid film thickness. The diagnostics methods are based on laser-induced fluorescence (LIF) of the organic tracer ethyl acetoacetate added to the liquid in sub-percent (by mass) concentration levels, and on spontaneous Raman scattering of liquid water, respectively, both with excitation at 266 nm. Signal intensities were calibrated with measurements on liquid layers of known thickness in a range between 0 and 500 μm. Detection via an image doubler and appropriate filtering in both light paths enabled the simultaneous detection of two-dimensional liquid film thickness information from both methods. The thickness of water films on transparent quartz glass plates was determined with an accuracy of 9% for the tracer LIF and 15% for the Raman scattering technique, respectively. The combined LIF/Raman measurements also revealed a preferential evaporation of the current tracer during the time-resolved recording of film evaporation.     

Dielectric response of aligned semiconducting single-wall nanotubes

We report measurements of the full intrinsic optical anisotropy of isolated single-wall carbon nanotubes (SWNTs). By combining absorption spectroscopy with transmission ellipsometry and polarization-dependent resonant Raman scattering, we obtain the real and imaginary parts of the SWNT permittivity from aligned semiconducting SWNTs dispersed in stretched polymer films. Our results are in agreement with theoretical predictions, highlighting the limited polarizability of excitons in a quasi-1D system.     

饱和激发下叶绿素荧光非线性变化及影响分析

叶绿素浓度是海洋初级生产力的重要指标之一,激光诱导荧光技术可以实现海水叶绿素浓度的快速测量。测量叶绿素浓度的传统激光诱导荧光原理,是利用叶绿素荧光与水体Raman散射的强度比值（I_F/R）进行反演,即叶绿素浓度n_chl＝CI_F/R,其中C为系统常量。这是依据叶绿素荧光685 nm、水体Raman散射强度都与激发光强呈线性关系。然而,该理论并没有考虑诱导荧光饱和现象的存在。当诱导激光强度达到一定程度后,685 nm荧光强度随激发光强非线性变化。另外,值得注意的是,水体Raman散射并不存在信号饱和现象。为了探讨饱和激发造成荧光非线性变化的影响,在激光诱导荧光技术测量叶绿素浓度的实验中,设计两种测量方案,即：不同激光功率诱导单一浓度样本的荧光测量,和固定激光功率时不同浓度样本的荧光测量。实验中利用Nd∶YAG三倍频激光355 nm激发获得叶绿素溶液的404 nm处 Raman散射和685 nm荧光。实验结果分为2部分进行讨论：（1）为了分析饱和激发造成荧光变化的非线性特性,通过调节激发光功率测量溶液的受激发射光谱,发现水体Raman散射强度与激发光强呈线性关系,而685 nm荧光强度出现饱和激发下的非线性变化。而且,随叶绿素浓度的增加,685 nm荧光的非线性趋势更为明显,Raman散射强度与激发光强的线性关系中斜率变小。数据分析表明,685 nm荧光数据拟合的4阶多项式和Raman散射效率值,可以定性地表征685 nm荧光的饱和程度。（2）考虑实际海洋激光雷达探测叶绿素浓度应用中存在饱和激发荧光非线性现象,为了分析荧光非线性对传统叶绿素浓度反演理论适用性的影响,在固定激发光强情况下对不同浓度叶绿素溶液的发射光谱进行测量。将激发光功率调节至52.00,80.70,132.10和197.30 mW·cm-2,获取相应激发光强下685 nm荧光与水体Raman散射的强度比值和叶绿素浓度之间的关系。实验表明,激发光强不变的情况下,685 nm荧光与水体Raman散射的强度比值,与叶绿素浓度仍满足线性关系。但是,在较高光强激发时,饱和激发造成的叶绿素荧光非线性变化,导致利用传统激光诱导荧光理论反演的叶绿素浓度值偏小。因此,需要对饱和激发下荧光非线性的影响进行修正,其关系为I_F/R=n_chl/C+C_F,修正值C_F不可忽略。另外,值得一提的是,修正关系中系统常量C随激发光强增加而增大。研究表明,饱和激发造成的荧光非线性,会对激光诱导荧光技术测量叶绿素浓度产生影响,但由于造成荧光非线性因素的复杂性,仅通过荧光数据拟合获得的多项式,无法定量说明其影响权重。然而,当激发光强不变时,可以实验测量获得基于激光诱导荧光原理的修正关系,从而准确反演叶绿素浓度。     

Evolution and impingement of an automotive fuel spray investigated with simultaneous Mie/LIF techniques

The spatial and temporal evolution of an automotive hollow-cone-type spray was investigated with laser-based imaging diagnostics. Optical conditions of an IC engine were emulated with a test cell that was built from an engine cylinder head to hold a high-pressure gasoline-fuel injector. The use of iso-octane fuel that was doped with 3-pentanone allowed measurements of laser-induced fluorescence (LIF) after excitation with a KrF excimer-laser beam. A versatile optical filter system was designed and built that permits simultaneous measurements of Mie-scattering and laser-induced-fluorescence images using a single laser-light sheet and a single intensified CCD camera. The influence of background signals, caused by reflection of signal light from surfaces, laser-sheet intensity attenuation and signal decrease by scattering, was characterized. Mass distributions showed a distinct pre-spray phase, more so than the Sauter mean diameter (SMD) that was determined from the ratio of LIF to Mie signals using single pulse as well as averaged image pairs. Significant changes in SMD distributions were found after the spray had impinged on a flat surface. The impingement also led to the buildup of a liquid film whose thickness was quantitatively determined from LIF images. Received: 5 December 2000 / Revised version: 28 February 2001 / Published online: 23 May 2001     

激光诱导水体中DOM的荧光猝灭特性分析

以355 nm激光为激发光源,在实验室中用激光诱导荧光(LIF)方法以不同浓度的腐殖酸为测量样品研究了水体中溶解有机物(DOM)的荧光猝灭特性。研究表明,随着腐殖酸浓度的增加,水拉曼散射强度逐渐减弱,当浓度为40 mg·L-1时,水拉曼散射信号几乎完全被DOM的荧光基态分子所吸收,而DOM的荧光强度随着浓度的增加,先是线性增加,当浓度为16 mg·L-1时,荧光强度达到最大,再继续增加腐殖酸浓度,荧光强度则缓慢降低。因此,通过对不同浓度下腐殖酸荧光猝灭特性的分析,可以更加有效的实现水体中DOM浓度的探测。     

Thermal loss mechanism in the generation of multifrequency laser emission via stimulated Raman scattering and four-wave Raman mixing studied by photothermal refraction spectroscopy

The heat produced in conjunction with the processes of stimulated Raman scattering and four-wave Raman mixing in hydrogen was measured by photothermal refraction spectroscopy. Many vibrational, rotational, and vibrationally shifted rotational Raman lines are exclusively/simultaneously generated by changing the polarization of the laser beam and the hydrogen pressure. Thermal loss occurs predominantly from vibrational Raman scattering, which can be ascribed to a large Raman shift frequency of 4155 cm^-1 for the vibrational transition. In contrast to stimulated Raman scattering, little or no thermal loss is observable during the process of four-wave Raman mixing. Received: 12 April 1999 / Revised version: 12 July 1999 / Published online: 20 October 1999     

Suppression of quantum scattering in strongly confined systems

We demonstrate that scattering of particles strongly interacting in three dimensions (3D) can be suppressed at low energies in a quasi-one-dimensional (1D) confinement. The underlying mechanism is the interference of the s- and p-wave scattering contributions with large s- and p-wave 3D scattering lengths being a necessary prerequisite. This low-dimensional quantum scattering effect might be useful in "interacting" quasi-1D ultracold atomic gases, guided atom interferometry, and impurity scattering in strongly confined quantum wire-based electronic devices.     

Measurements of flame orientation and scalar dissipation in turbulent partially premixed methane flames

Three turbulent flames were studied using a new experimental facility developed at Sandia National Laboratories. Line imaging of Raman and Rayleigh scattering and CO laser-induced fluorescence (LIF) yielded information on all major species, temperature, mixture fraction, and a 1D surrogate measure of scalar dissipation. Simultaneously, crossed planar OH LIF imaging provided information on the instantaneous flame orientation, allowing estimation of the full 3D (flame-normal) scalar dissipation rate. The three flames studied were methane–air piloted jet flames (Sandia flames C, D, and E), which cover a range in Reynolds number from 13,400 to 33,600. The statistics of the instantaneous flame orientation are examined in the different flames, with the purpose of studying the prevailing kinematics of isoscalar contours. The 1D and 3D results for scalar dissipation rate are examined in detail, both in the form of conditional averages and in the form of probability density functions. The effect of overall strain and Reynolds number on flame suppression and eventual extinction is also investigated, by examining the doubly conditional statistics of temperature in the form of S-shaped curves. This latter analysis reveals that double conditioning of temperature on both mixture fraction and scalar dissipation does not collapse the data from these flames onto the same curve at low scalar dissipation rates, as might be expected from simple flamelet concepts.     

Raman lidar for the study of liquid water and water vapor in the troposphere

A Raman lidar system based on a tripled Nd:YAG laser is used for profiling of water vapor and liquid water in the troposphere. The Raman signals from water in the gas and liquid state are separated by interference filters and their relative intensities are studied for different atmospheric conditions. For clean weather or immediately after the rain the Raman signal from liquid water inside PBL is about one order of magnitude lower than the signal from water vapor. But during cloud measurements both Raman signals become comparable and the results of water vapor measurements must be corrected for the interference of liquid water Raman scattering. The obtained results are used for the estimation of liquid water content in the atmosphere. Received: 4 October 1999 / Revised version: 18 February 2000 / Published online: 11 May 2000     

Nonlinear interferometric vibrational imaging

Coherent anti-Stokes Raman scattering (CARS) processes are "coherent," but the phase of the anti-Stokes radiation is lost by most incoherent spectroscopic CARS measurements. We propose a Raman microscopy imaging method called nonlinear interferometric vibrational imaging, which measures Raman spectra by obtaining the temporal anti-Stokes signal through nonlinear interferometry. With a more complete knowledge of the anti-Stokes signal, we show through simulations that a high-resolution Raman spectrum can be obtained of a molecule in a single pulse using broad band radiation. This could be useful for identifying the three-dimensional spatial distribution of molecular species in tissue.     

Raman scattering measurements of molecular hydrogen in a low-density, arc-heated plasma

Raman scattering measurements of molecular hydrogen density and temperature were made in a low-density, arc-heated plasma flow. Pulsed-laser excitation was used to improve the signal-to-noise ratio in this high-background environment. Quantum-limited detection was achieved through the use of gated photon counting and a high-power Nd:YAG laser. Radial profiles of rotational temperature and density at the exit plane were measured for five power levels. In all cases the profiles were asymmetric about the centerline. The rotational temperatures were compared with the translational temperatures of atomic hydrogen from LIF studies and found to be slightly lower. This result suggests that this flow, like the cold flow, is not in translational-rotational equilibrium.     

Laser-induced fluorescence thermometry and concentration measurements on NOA–X (0-0) transitions in the exhaust gas of high pressure CH4/air flames

Laser-Induced Fluorescence (LIF) excitation spectra in the NOA–X (0-0) band were used for temperature measurements in the postflame region of high-pressure CH₄/air flames. To improve the quality of the measured spectra and to perform reliable line-shape measurements, the initial mixture was doped with approximately 400 ppm NO. At pressures up to 18 bar, excellent agreement was obtained between NO LIF temperatures and NARS/rotational Raman temperatures. Effective broadening coefficients were also determined in these flames. Problems with quantitative concentration measurements of NO and single-pulse temperature measurements at high pressures are discussed.     

Hybrid Rayleigh,Raman and two‐photon excited fluorescence spectral confocal microscopy of living cells

A hybrid fluorescence–Raman confocal microscopy platform is presented, which integrates low‐wavenumber‐resolution Raman imaging, Rayleigh scatter imaging and two‐photon fluorescence (TPE) spectral imaging, fast ‘amplitude‐only’ TPE‐fluorescence imaging and high‐spectral‐resolution Raman imaging. This multi‐dimensional fluorescence–Raman microscopy platform enables rapid imaging along the fluorescence emission and/or Rayleigh scatter dimensions. It is shown that optical contrast in these images can be used to select an area of interest prior to subsequent investigation with high spatially and spectrally resolved Raman imaging. This new microscopy platform combines the strengths of Raman ‘chemical’ imaging with light scattering microscopy and fluorescence microscopy and provides new modes of correlative light microscopy. Simultaneous acquisition of TPE hyperspectral fluorescence imaging and Raman imaging illustrates spatial relationships of fluorophores, water, lipid and protein in cells. The fluorescence–Raman microscope is demonstrated in an application to living human bone marrow stromal stem cells. Copyright © 2009 John Wiley & Sons, Ltd.     

Experimental analysis of local flame extinction in a turbulent jet diffusion flame by high repetition 2-D laser techniques and multi-scalar measurements

In this paper, we present a detailed experimental study of turbulence chemistry interactions in the “DLR_B” turbulent jet diffusion flame. The flame operates on mixtures of CH₄, H₂, and N₂ in the fuel stream at Re = 22,800 and is a target flame within the TNF workshop. Extinction and re-ignition events can be tracked in real time and related to the underlying flow field phenomena and temperature fields. Time resolved measurements of OH radical concentration fields are performed in combination with temperature and velocity field measurements. For this purpose, we combined high repetition rate (33 kHz) PLIF imaging with stereoscopic PIV and double pulse Rayleigh imaging techniques. Comparisons are made with results from multi-scalar Raman/Rayleigh/LIF point measurements that reveal the thermochemical state of the flame. The large deviations from equilibrium observed on resulting OH/temperature joint pdfs could be related to strain rate and Damköhler number variations caused by turbulent flow structures leading to frequent extinctions. The 2D measurement series uniquely reveal the underlying mechanism that can lead to such events. Finally, comparisons are made to strained laminar flame calculations, which are generally found to be in good agreement with the measured data.     

Plane Wave and Gaussian Beam Scattering by Long Dielectric Cylinders: 2.5D Simulations versus Measurements

For the development of millimeter wave imaging systems, it is important to be able to simulate some representative scattering configurations. Typically, Gaussian beams are used in active imaging systems. Since these beams only illuminate a spatially limited region, many objects can be treated as infinitely long 2D (in)homogenous cylinders. However, the incident Gaussian beams have a 3D character. Therefore, a dedicated 2.5D scattering simulator was developed. In this paper, simulation results obtained with this simulator are compared to measurements obtained from a bi-static microwave set-up and from a W-band millimeter wave set-up. Comparison of simulations and measurements proves that the 2.5D algorithm is a good simulation tool to study scattering of long inhomogeneous cylinders, illuminated by 3D plane waves or 3D Gaussian beams under different elevation angles.     

Temperature and concentration measurements in acetylene-nitrogen mixtures in the range 300–600 K using dual-broadband rotational CARS

Pure rotational coherent anti-Stokes Raman scattering (CARS) experiments have been performed in acetylene for temperatures ranging from 294 to 582 K, and in mixtures of acetylene and nitrogen in the mole fraction range of 0.06–0.32 for acetylene at room temperature. The experimental spectra are evaluated by a least-square fitting to libraries of theoretically calculated spectra using two different Raman linewidth models, one with and one without dependence on the rotational quantum number J. It is found that a J-dependent model is favourable, both regarding temperature measurements in pure acetylene, and simultaneous acetylene concentration and temperature measurements in different mixtures of acetylene and nitrogen. For the temperature measurements performed in pure acetylene the temperature inaccuracy is generally less than 2% when the J-dependent model for the Raman linewidths is used. It is found that fitting the value of the non-resonant susceptibility significantly improves the quality of the spectral fits and is a requirement for high temperature accuracy with the present model. The evaluated concentrations show a maximum error of 13% on a relative scale. Potential sources of systematical errors both regarding measured temperatures and acetylene concentrations are discussed. Received: 8 June 1999 / Revised version: 3 Spetember 1999 / Published online: 3 November 1999