铜掺杂多孔硅的光致荧光猝灭

采用浸泡镀敷的方法在多孔硅表面形成了一铜镀层,通过对掺铜前后多孔硅的光致发光(PL)谱和傅里叶变换红外(FTIR)吸收光谱的研究,讨论了铜在多孔硅表面的吸附对其光致发光的影响。实验表明,掺铜对多孔硅的光致发光具有明显的猝灭效应,并使多孔硅的发光峰位蓝移。由于多孔硅表面铜的吸附使硅-氢键明显减少,而铜原子和硅的悬挂键成键会形成新的非辐射复合中心,从而使多孔硅的光致发光强度衰减。且浸泡溶液的浓度越高,这种猝灭效应越明显。而多孔硅发光峰位的蓝移,则是由于在发生金属淀积的同时伴随着多孔硅表面Si的氧化过程(纳米Si氧化为SiO2)的缘故。     

Ag Deposition Forms and Uniformity on Porous Silicon by Electrochemical Method

采用电化学沉积Ag的方法对多孔硅表面进行钝化改善其发光性能,探讨了沉积电流密度大小与沉积Ag的形式以及多孔硅表面亲水性处理对沉积Ag均匀性的影响. 结果表明,改变沉积电流密度大小后出现了两个临界电流密度,即不发生Ag沉积和在PS表层形成Ag电镀,深入PS孔道内沉积Ag的电流密度范围为50～400 A/cm²;多孔硅表面亲水性处理对沉积Ag均匀性有积极作用,在相同的实验条件下,未经表面亲水性处理的疏水多孔硅表面沉积Ag不均匀,而经过SC-1溶液处理后的亲水多孔硅表面上沉积Ag分布较均匀. 进一步研究了均匀沉积Ag钝化处理对PS的光致发光强度和稳定性的影响,证明采用Ag钝化处理能有效地抑制发光强度的衰减;而过量的Ag沉积会使PS发生荧光猝灭现象.     

激光促进多孔硅内表面氧化与光致发光的退化

本文对刚制备的以及分别经以下三种情况:1.样品在1大气压的氧气中经激光(Ar~+激光器的48.80nm线,功率密度为1.77W/cm~2)连续照射1小时;2.样品在1大气压的氧气中在没有激光照射的情况下保持1小时;3.样品在1.3×10~2Pa真空度下用激光连续照射1小时处理后的多孔硅在室温下进行了光致发光谱和傅里叶变换红外吸收测量,研究了处理前后光谱的变化。实验发现经第一种情况处理后光致发光峰位蓝移了约0.1eV,发光强度衰减了二十几倍,相应的其红外光谱中与氧有关的吸收峰强度大幅度增长,而经第二,三两种情况处理后它们的光致发光及红外吸收谱则无大的变化。研究表明在氧气中激光辐照能大大加速多孔硅内表面的氧化。我们认为很可能是多孔硅内表面的氧化作用使光致发光峰位蓝移,由氧化作用产生的非辐射复合中心导致光致发光效率的下降。     

自然氧化引起的多孔硅光致发光光谱移动问题

多孔硅发光是激发电子通过表面态间接的复合过程。自然氧化引入新的表面态，改变了表面态的分布，从而引起了多孔硅光致发光光谱的移动。 关键词：     

低温湿氧氧化提高多孔硅发光的稳定性

用低温湿氧氧化方法对多孔硅进行后处理,获得了光致发光强度强、发光稳定的样品,顺磁共振谱表明这种样品表面的悬挂键密度较小,通过对样品红外光谱的测试和分析,指出SiH(O₃),SiH(SiO₂),SiH₂(O₂)结构的产生是实验中多孔硅稳定性提高的原因. 关键词：     

多孔硅的制备条件对其光致发光特性的影响

不同的实验条件下制备的多孔硅的光致发光(PL)特性是不同的,这是许多研究产生分歧的主要原因。对比分析了阳极氧化电流密度、阳极氧化时间、溶液浓度以及自然氧化时间对多孔硅光致发光光谱的影响。认为在一定的范围内,多孔硅的发光峰位会随电流密度的增大而蓝移,要获得较强的发光,需要选择合适的电流密度;随着腐蚀时间的延长,多孔硅的发光峰位也发生蓝移。当HF酸的浓度较小时,峰位随浓度的增大表现为向低能移动;而当HF酸的浓度较大时,峰位随浓度的增大则表现为移向高能。多孔硅在空气中自然氧化,其发光峰位发生蓝移,而发射强度随放置时间的延长而降低。并用量子限制模型和发光中心模型对实验结果进行解释。     

水稻中的纳米硅及其紫外吸收

为了了解水稻中硅的亚显微结构及其紫外吸收特性,根据强酸不会腐蚀SiO₂玻璃的事实,选择湿消化方法分离水稻中的硅体。以浓硫酸和硝酸混合液分别处理水稻叶片和稻壳,经多级沉降分离出其中的硅体。X射线光电子能谱结果表明硅体距离表面10 nm以内碳相对质量为35.05%,远高于硅体表面(5.88%),说明硅质壁能够阻止强酸进入硅体内部,避免硅体内氧化,保持硅体结构完整和相对独立的理化性质。电镜显示硅体SiO₂结构致密,由1～2 nm的SiO₂凝胶粒子粘聚而成,纳米颗粒相互融合组成排列方向一致的纳米棒,内部还有微米尺度(≤1μm)和纳米尺度(≤1～2 nm)的隙孔。颖壳硅体最大吸收位于285 nm;叶片纳米硅对紫外辐射的吸收极其有限,表明水稻颖壳和叶片硅体对紫外辐射具有不同的抵抗机制。     

提高多孔硅传感特性的一种新方法(英文)

研究了多孔硅(PS)吸附有机溶剂分子后对多孔硅荧光谱的淬灭效应。结果表明:淬灭多孔硅发光的有机溶剂分子是极性分子,有机溶剂分子的极性不同对多孔硅发光的淬灭程度也不同,且有些有机溶剂分子吸附氧化多孔硅比吸附多孔硅引起的发光淬灭具有更好的可逆性和选择性;用含有胺基的正丁胺(CH3CH2CH2CH2-NH2)作碳源,用射频辉光放电等离子系统在多孔硅表面沉积c n膜对多孔硅进行钝化处理后发现:其电致发光强度明显增强,发光峰位兰移,且在大气中存放60天后,其电致发光谱强度基本不衰减,峰位不再移动。经钝化处理的器件较未经处理的器件具有小的串联电阻Rs和低的驱动电压。这为提高多孔硅的传感特性提供了一种新方法。     

多孔硅表面形貌的观测和探讨

一、引言多孔硅室温下较强的光致发光现象给全硅大规模光电集成电路和硅基发光器件的开发带来曙光，但要把它变为现实仍有许多问题要解决，就以发光机理为例，仍有不同意见[1].为此必须深入研究其特性，为探讨发光机理提供依据.已有作者观察到发光畴区[2]，测得多孔硅成分近于二氧化硅[3]，观察到快和慢的发光带[4]以及证实自然氧化引入新的表面态[5]等.但迄今为止测量的均为晾干后的多孔硅，而未深究在空气中贮存干燥过程中形貌的变化.本文对多孔硅在空气中贮存初期表面形貌的变化做了显微观测和探讨.还尝试测量了多孔硅／硅的界面特性.二…     

一种新型阳极氧化多孔硅技术

在适当条件下氧化多孔硅是提高多孔硅发光强度的良好途径,提出了一种新型阳极氧化方法,并探讨了该方法所涉及的阳极氧化条件。采用含CH3CSNH2的HF酸水溶液作为氧化剂对初始多孔硅进行了湿法阳极氧化,发现氧化使多孔硅光致发光性质得到极大改善,进而研究了氧化电流、氧化温度、氧化时间等一系列因素对氧化多孔硅光致发光强度的影响,并给出了合理解释。实验发现,在1mA,10min,60℃的氧化条件下,采用阳极氧化技术使多孔硅发光强度增强了18倍。     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.     

A stereo matching algorithm using multi-peak candidate matches and geometric constraints

Gray cross correlation matching technique is adopted to extract candidate matches with gray cross correla- tion coefficients less than some certain range of maximal correlation coefficient called multi-peak candidate matches. Multi-peak candidates are extracted corresponding to three closest feature points at first. The corresponding multi-peak candidate matches are used to construct the model polygon. Correspondence is determined based on the local geometric relations between the three feature points and the multi-peak candidates. The disparity test and the global consistency checkout are applied to eliminate the remaining ambiguous matches that are not removed by the local geometric relational test. Experimental results show that the proposed algorithm is feasible and accurate.