SO_2对Co_3O_4/Al_2O_3选择性催化氧化NO的影响

采用流动态原位IR ,TPD及XPS技术研究了NO及SO2 在Co3 O4 /Al2 O3 金属氧化物催化剂表面上的吸附及脱附行为 ,并与该催化剂上模拟烟道气中NO的选择性催化氧化活性相关联 ,考察了SO2 对该反应过程的影响及作用机理 .     

Low-temperature catalytic adsorption of NO on activated carbon materials

The catalytic adsorption of NO on activated carbon materials provides an appropriated alternative for the control of low-concentration emissions of this air pollutant. The surface complexes formed upon NO adsorption at 30 degrees C were studied by X-ray photoelectron spectroscopy (XPS) and temperature-programmed desorption (TPD). The effects of the addition of O2 and the presence of copper as a catalyst were studied. Copper assisted the oxygen transfer to the carbon matrix. For the Cu-impregnated carbon sample, the presence of O2 favored NO adsorption by increasing the breakthrough time, the adsorption capacity, and the formation of nitrogen and oxygen complexes of higher thermal stabilities, which mainly desorbed as NO and CO2.     

Formation of C=C and Si-Cl adstructures by insertion reactions of cis-dichloroethylene and perchloroethylene on Si(100)2 x 1

The room-temperature adsorption and thermal evolution of cis-dichloroethylene (DCE) and perchloroethylene (PCE) on Si(100)2 x 1 have been studied by X-ray photoelectron spectroscopy and temperature programmed desorption (TPD) mass spectrometry. Unlike ethylene that is found to adsorb on Si(100)2 x 1 through a [2+2] cycloaddition reaction, cis-DCE and PCE appear to dechlorinate upon adsorption on the 2 x 1 surface through an insertion reaction preserving the C=C bond. Our C 1s XPS spectra are consistent with the existence of mono-sigma-bonded and di-sigma bonded dechlorinated adstructures for both cis-DCE and PCE. The presence of the XPS C 1s feature at 283.9 eV, characteristic of the (=C<(Si)(Si)) component, supports the formation of a unique tetra-sigma-bonded C(2) dimer (i.e., by full dechlorination) for PCE, which is found to be stable to 800 K. In marked contrast to PCE for which no organic desorption fragments are observed, m/z 26 TPD features at 590 and 750 K have been observed for cis-DCE. These features could be attributed to the formation of acetylene resulting from Cl beta-elimination of 2-chlorovinyl adspecies and to direct desorption of vinylene, respectively. Further annealing the cis-DCE and PCE samples to above 800 K produces SiC and/or carbon clusters. The TPD data also show HCl evolution over 810-850 K for both cis-DCE and PCE, the latter of which also exhibits an additional SiCl(2) evolution above 850 K. The present work illustrates that the insertion mechanism could be quite common in the surface chemistry of chlorinated ethylenes on the 2 x 1 surface.     

NO2 adsorption on ultrathin theta-Al2O3 films: formation of nitrite and nitrate species

Interaction of NO2 with an ordered theta-Al2O3/NiAl(100) model catalyst surface was investigated using temperature programmed desorption (TPD) and X-ray photoelectron spectroscopy (XPS). The origin of the NO(x) uptake of the catalytic support (i.e., Al2O3) in a NO(x) storage catalyst is identified. Adsorbed NO2 is converted to strongly bound nitrites and nitrates that are stable on the model catalyst surface at temperatures as high as 300 and 650 K, respectively. The results show that alumina is not completely inert and may stabilize some form of NO(x) under certain catalytic conditions. The stability of the NO(x) formed by exposing the theta-Al2O3 model catalyst to NO2 adsorption increases in the order NO2 (physisorbed or N2O4) < NO2 (chemisorbed) < NO2- < NO3-.     

Pt/MOx-SiO2 (M=Ce,Zr, Al)催化剂对CO和C3H8氧化性能的影响

采用共沉淀法制备质量比为1:1的MOx-SiO2(M=Ce,Zr,Al)复合氧化物,以此为载体采用浸渍法制备了铂基氧化型催化剂.考察了该系列催化剂在模拟柴油车尾气条件下,经SO2硫化前后对C3H8和CO的氧化性能.用X射线衍射(XRD)、低温N2吸附-脱附、氨气/氧气/二氧化碳程序升温脱附(NH3/O2/CO2-TPD)和X射线光电子能谱(XPS)等手段进行了表征.NH3-TPD证实催化剂表面存在多种酸中心,硫化后催化剂表面中强酸中心增多.O2-TPD证实催化剂表面存在α和β氧物种,硫化后催化剂表面氧脱附量减少.其中Pt/Al2O3-SiO2表面酸性最弱和表面氧脱附量最大.XPS结果表明新鲜催化剂经硫化后会使催化剂表面Pt的结合能降低.活性测试结果表明,三种催化剂对CO和C3H8的催化氧化活性均较好,其中Pt/ZrO2-SiO2抗SO2中毒性能最佳,具有良好的应用前景.     

Adsorption and decomposition of cyclohexanone (C6H10O) on Pt(111) and the (2 × 2) and (√3 × √3)r30°-Sn/Pt(111) surface alloys

Adsorption and decomposition of cyclohexanone (C(6)H(10)O) on Pt(111) and on two ordered Pt-Sn surface alloys, (2 × 2)-Sn/Pt(111) and (√3 × √3)R30°-Sn/Pt(111), formed by vapor deposition of Sn on the Pt(111) single crystal surface were studied with TPD, HREELS, AES, LEED, and DFT calculations with vibrational analyses. Saturation coverage of C(6)H(10)O was found to be 0.25 ML, independent of the Sn surface concentration. The Pt(111) surface was reactive toward cyclohexanone, with the adsorption in the monolayer being about 70% irreversible. C(6)H(10)O decomposed to yield CO, H(2)O, H(2), and CH(4). Some C-O bond breaking occurred, yielding H(2)O and leaving some carbon on the surface after TPD. HREELS data showed that cyclohexanone decomposition in the monolayer began by 200 K. Intermediates from cyclohexanone decomposition were also relatively unstable on Pt(111), since coadsorbed CO and H were formed below 250 K. Surface Sn allowed for some cyclohexanone to adsorb reversibly. C(6)H(10)O dissociated on the (2 × 2) surface to form CO and H(2)O at low coverages, and methane and H(2) in smaller amounts than on Pt(111). Adsorption of cyclohexanone on (√3 × √3)R30°-Sn/Pt(111) at 90 K was mostly reversible. DFT calculations suggest that C(6)H(10)O adsorbs on Pt(111) in two configurations: by bonding weakly through oxygen to an atop Pt site and more strongly through simultaneously oxygen and carbon of the carbonyl to a bridged Pt-Pt site. In contrast, on alloy surfaces, C(6)H(10)O bonds preferentially to Sn. The presence of Sn, furthermore, is predicted to make the formation of the strongly bound C(6)H(10)O species bonding through O and C, which is a likely decomposition precursor, thermodynamically unfavorable. Alloying with Sn, thus, is shown to moderate adsorptive and reactive activity of Pt(111).     

Adsorption and thermal reactions of alkanethiols on pt(111): Dependence on the length of the alkyl chain

The adsorption and thermal decomposition of alkanethiols (R-SH, where R = CH3, C2H5, and C4H9) on Pt(111) were studied with temperature-programmed desorption (TPD) and X-ray photoelectron spectroscopy (XPS) with synchrotron radiation. Dissociation of sulfhydryl hydrogen (RS-H) of alkanethiol results in the formation of alkanethiolate; the extent of dissociation at an adsorption temperature of 110 K depends on the length of the alkyl chain. At small exposure, all chemisorbed CH3SH, C2H5SH, and C4H9SH decompose to desorb hydrogen below 370 K and yield carbon and sulfur on the surface. Desorption of products containing carbon is observed only at large exposure. In thermal decomposition, alkanethiolate is proposed to undergo a stepwise dehydrogenation: R'-CH2S --> R'-CHS --> R'-CS, R' = H, CH3, and C3H7. Further decomposition of the R'-CS intermediate results in desorption of H2 at 400-500 K and leaves carbon and sulfur on the surface. On the basis of TPD and XPS data, we conclude that the density of adsorption of alkanethiol decreases with increasing length of the alkyl chain. C4H9SH is proposed to adsorb mainly with a configuration in which its alkyl group interacts with the surface; this interaction diminishes the density of adsorption of alkanethiols but facilitates dehydrogenation of the alkyl group.     

Synergistic effect between NO2 and SO2 in their adsorption and reaction on gamma-alumina

Field measurements showed that there exists a correlation between nitrate and sulfate on mineral dust. In this work, the synergistic mechanism of adsorption and reaction between SO2 and NO2 on gamma-alumina was studied using in situ diffusion reflectance infrared Fourier spectroscopy (in situ DRIFTS) and temperature programmed desorption (TPD). The results revealed that the reaction pathway of NO2 adsorbed on alumina was altered in the presence of SO2. In the absence of SO2, nitrite was found to be an intermediate in the oxidation of NO2 to surface nitrate species. However, in the presence of SO2, the formation of nitrite was inhibited and a new intermediate, dinitrogen tetraoxide (N2O4), was observed. On the other hand, surface tetravalent sulfur species S(IV), including bisulfite and sulfite, were oxidized to sulfate in air condition when NO2 was present. The atmospheric implication of this synergistic effect was also discussed.     

CO oxidation on nanostructured SnO(x)/Pt(111) surfaces: unique properties of reduced SnO(x)

We have investigated surface CO oxidation on "inverse catalysts" composed of SnO(x) nanostructures supported on Pt(111) using X-ray photoelectron spectroscopy (XPS), low-energy ion scattering spectroscopy (LEISS) and temperature-programmed desorption (TPD). Nanostructures of SnO(x) were prepared by depositing Sn on Pt(111) pre-covered by NO(2) layers at low temperatures. XPS data show that the SnO(x) nanoparticles are highly reduced with Sn(II)O being the dominant oxide species, but the relative concentration of Sn(II) in the SnO(x) nanoparticles decreases with increasing Sn coverage. We find that the most active SnO(x)/Pt(111) surface for CO oxidation has smallest SnO(x) coverage. Increasing the surface coverage of SnO(x) reduces CO oxidation activity and eventually suppresses it altogether. The study suggests that reduced Sn(II)O, rather than Sn(IV)O(2), is responsible for surface CO oxidation. The occurrence of a non-CO oxidation reaction path involving reduced Sn(II)O species at higher SnO(x) coverages accounts for the decreased CO oxidation activity. From these results, we conclude that the efficacy of CO oxidation is strongly dependent on the availability of reduced tin oxide sites at the Pt-SnO(x) interface, as well as unique chemical properties of the SnO(x) nanoparticles.     

SO2对NO催化氧化过程的影响V.NiO/γ-Al2O3上SO2的作用机理

采用程序升温脱附(TPD)及漫反射原位红外光谱(DRIFT)技术分析比较了SO2存 在前后，NO—02反应气体在NiO／γ—Al2O3催化剂上所形成吸附物种的变化情况， 发现SO2能促使硝酸盐物种在低温分解并释放出NO2，而且耐热稳定的硝酸盐物种也 比单纯NO-02吸附时多．室温时催化剂表面上的SO2以弱吸附物种为主，特征红外吸 收峰位于1324cm^-1附近，温度升高后表面硫酸盐物种数量增多．关联SO2气氛中 NO2的生成规律后得出，类似于铅室反应中间体的多分子吸附物种[NO2(SO3)x]是产 生N02的活性物种，由SO2在载体或催化剂表面弱碱位吸附后吸引气相NO所产生，解 离O^-起到稳定活性物种和补充弱碱位的作用．同时该物种也是毒性物质SO4^2-的 前驱体，当KO氧化反应发生后催化剂的失活也开始了．     

Adsorption and reaction of SO2 with a polycrystalline UO2 film: promotion of S-O bond cleavage by creation of O-defects and Na or Ca coadsorption

To characterize UO(2) for its possible use in desulfurization applications, the interactions of molecular sulfur dioxide (SO(2)) with a polycrystalline uranium dioxide film have been studied by means of X-ray photoelectron spectroscopy (XPS), temperature-programmed desorption (TPD), and low-energy ion scattering (LEIS). The stoichiometric, oxygen-deficient, calcium-precovered and sodium-precovered UO(2) surfaces have been characterized. The changes in oxide reactivity upon creation of oxygen vacancies and coadsorption of sodium and calcium have been studied. After creation of a reduced UO(2-x) surface (x approximately 0.44) via Ar(+) sputtering, the U 4f XPS spectrum shows conspicuous differences that are good indicators of the surface stoichiometry. Molecular SO(x) formation (x = 2-4) is observed after SO(2) deposition onto stoichiometric UO(2) and onto UO(2) precovered with small amounts (<1 ML) of Na or Ca; complete dissociation of SO(2) is not observed. Heating leads to desorption of the SO(x) species and to transformation of SO(2) to SO(3) and SO(3) to SO(4). On oxygen-deficient UO(2) and on UO(2) precovered with large Na or Ca coverages (> or =4 ML), both the formation of SO(x)= species and complete dissociation of SO(2) are observed. A higher thermal stability of the sulfur components is observed on these surfaces. In all cases for which dissociation occurs, the XPS peak of atomic sulfur shows similar structure: three different binding states are observed. The reactivity of oxygen-deficient UO(2) and sodium- and calcium-precovered UO(2) (coverages > or = 4 ML) is attributed to charge transfer into the antibonding LUMO of the adsorbed molecule.     

Low temperature H2O and NO2 coadsorption on theta-Al2O3/NiAl(100) ultrathin films

The coadsorption of H(2)O and NO(2) molecules on a well-ordered, ultrathin theta-Al(2)O(3)/NiAl(100) film surface was studied using temperature programmed desorption (TPD), infrared reflection absorption spectroscopy (IRAS), and X-ray photoelectron spectroscopy (XPS). For H(2)O and NO(2) monolayers adsorbed separately on the theta-Al(2)O(3)/NiAl(100) surface, adsorption energies were estimated to be 44.8 and 36.6 kJ/mol, respectively. Coadsorption systems prepared by sequential deposition of NO(2) and H(2)O revealed the existence of coverage and temperature-dependent adsorption regimes where H(2)O molecules and the surface NO(x) species (NO(2)/N(2)O(4)/NO(2)(-),NO(3)(-)) form segregated and/or mixed domains. Influence of the changes in the crystallinity of solid water (amorphous vs crystalline) on the coadsorption properties of the NO(2)/H(2)O/theta-Al(2)O(3)/NiAl(100) system is also discussed.     

Heats of adsorption using temperature programmed adsorption equilibrium: application to the adsorption of CO on Cu/A12O3 and H2 on Pt/Al2O3

A new simple analytical procedure is described that allows the determination of the heats of adsorption (denoted E(theta)) of adsorbed species at several coverages (theta's) using a single experiment. This procedure is an extension of an original method previously developed (denoted AEIR: adsorption equilibrium infrared spectroscopy). A mass spectrometer is used to determine the amounts of gas (in the present study, CO and H2) either desorbed from or adsorbed on a metal supported catalyst (4.7% Cu/Al2O3 and 2.9% Pt/Al2O3) during the perturbation of the adsorption equilibrium due to a controlled change of the adsorption temperature (Ta) at a quasi-constant adsorption pressure (Pa). These amounts allow us to follow the evolution of the adsorption equilibrium coverage (theta(e)) with Ta at the quasi-constant partial pressure (Pa). Then, the curve theta(e) = f(Ta) provides Etheta = f(theta) with the support of an adsorption model. This procedure presents several advantages as compared to the TPD methods, in particular, considering the theoretical supports linked to the exploitation of the experimental data. As compared to AEIR, the TPAE procedure allows one to study the heats of adsorption of adsorbed species that are not detectable by IR. However, it is not adapted if surface reactions occur in parallel to adsorption/desorption processes.     

具有低SO_2氧化活性的Pt/Zr_xTi_(1-x)O_2柴油车氧化催化剂的制备及性能

采用共沉淀法制备了一系列ZrxTi1-xO2(x=0.0,0.1,0.5,0.9,1.0)复合氧化物,并以此为载体,用等孔体积浸渍H2PtCl6制得Pt/ZrxTi1-xO2柴油车氧化催化剂.运用N2吸附-脱附,X射线多晶粉末衍射,X射线光电子能谱,H2程序升温还原和NH3程序升温脱附等手段对催化剂进行了表征.结果表明,在系列催化剂样品中,Zr0.1Ti0.9O2复合氧化物主要以锐钛矿形式存在,具有较好的织构性能,样品的比表面积达94m2/g,孔体积为0.33cm3/g.相应地,Pt/Zr0.1Ti0.9O2催化剂表现出优异的催化氧化性能,HC和CO的起燃温度(T50)分别为185和174oC,完全转化温度(T90)分别为197和201oC;且具有较低的SO2氧化活性,350oC时SO2仅转化25.5%.     

不同载体负载的Cr基催化剂催化CO2氧化异丁烷脱氢制异丁烯

制备了介孔分子筛MSU-1,γ-A12O3,AC(活性炭)和MgO负载的CrOx催化剂,并考察了其催化CO2氧化异丁烷脱氢制异丁烯反应性能.结果表明,各催化剂活性的顺序为:CrOx/MSU-1 ＞CrOx/A12O3＞ CrOx/AC＞ CrOJMgO.其中在CrOx/MSU-1催化剂上,异丁烷的转化率和异丁烯的收率分...     

Surface chemistry of CN bond formation from carbon and nitrogen atoms on Pt(111)

The mechanism of CN bond formation from CH3 and NH3 fragments adsorbed on Pt(111) was investigated with reflection absorption infrared spectroscopy (RAIRS), temperature-programmed desorption (TPD), and X-ray photoelectron spectroscopy (XPS). The surface chemistry of carbon-nitrogen coupling is of fundamental importance to catalytic processes such as the industrial-scale synthesis of HCN from CH4 and NH3 over Pt. Since neither CH4 nor NH3 thermally dissociate on Pt(111) under ultrahigh vacuum (UHV) conditions, the relevant surface intermediates were generated through the thermal decomposition of CH3I and the electron-induced dissociation of NH3. The presence of surface CN is detected with TPD through HCN desorption as well as with RAIRS through the appearance of the vibrational features characteristic of the aminocarbyne (CNH2) species, which is formed upon hydrogenation of surface CN at 300 K. The RAIRS results show that HCN desorption at approximately 500 K is kinetically limited by the formation of the CN bond at this temperature. High coverages of Cads suppress CN formation, but the results are not influenced by the coadsorbed I atoms. Cyanide formation is also observed from the reaction of adsorbed N atoms and carbon produced from the dissociation of ethylene.     

Reactions of NO2 with BaO/Pt(111) model catalysts: the effects of BaO film thickness and NO2 pressure on the formation of Ba(NOx)2 species

The adsorption and reaction of NO(2) on BaO (<1, ～3, and >20 monolayer equivalent (MLE))/Pt(111) model systems were studied with temperature programmed desorption (TPD), X-ray photoelectron spectroscopy (XPS), and infrared reflection absorption spectroscopy (IRAS) under ultra-high vacuum (UHV) as well as elevated pressure conditions. NO(2) reacts with sub-monolayer BaO (<1 MLE) to form nitrites only, whereas the reaction of NO(2) with BaO (～3 MLE)/Pt(111) produces mainly nitrites and a small amount of nitrates under UHV conditions (P(NO(2))≈ 1.0 × 10(-9) Torr) at 300 K. In contrast, a thick BaO (>20 MLE) layer on Pt(111) reacts with NO(2) to form nitrite-nitrate ion pairs under the same conditions. At elevated NO(2) pressures (≥1.0 × 10(-5) Torr), however, BaO layers at all these three coverages convert to amorphous barium nitrates at 300 K. Upon annealing to 500 K, these amorphous barium nitrate layers transform into crystalline phases. The thermal decomposition of the thus-formed Ba(NO(x))(2) species is also influenced by the coverage of BaO on the Pt(111) substrate: at low BaO coverages, these species decompose at significantly lower temperatures in comparison with those formed on thick BaO films due to the presence of a Ba(NO(x))(2)/Pt interface where the decomposition can proceed at lower temperatures. However, the thermal decomposition of the thick Ba(NO(3))(2) films follows that of bulk nitrates. Results obtained from these BaO/Pt(111) model systems under UHV and elevated pressure conditions clearly demonstrate that both the BaO film thickness and the applied NO(2) pressure are critical in the Ba(NO(x))(2) formation and subsequent thermal decomposition processes.     

Dispersion and reactivity of copper catalysts supported on Al2O3-ZrO2

A series of CuO/Al(2)O(3)-ZrO(2) catalysts with Cu loadings varying from 1.0 to 20 wt % were prepared and characterized by X-ray diffraction (XRD), temperature-programmed reduction (TPR), temperature-programmed desorption (TPD) of CO(2) and NH(3), electron spin resonance (ESR), and Brunauer-Emmett-Teller surface area measurements. The dispersion and metal area of copper were determined by the N(2)O decomposition method. XRD results suggest that the copper oxide is present in a highly dispersed amorphous state at copper loadings < 10 wt % and as a crystalline CuO phase at higher Cu loadings. ESR results suggest the presence of two types of copper species on the Al(2)O(3)-ZrO(2) support. TPR results suggest well-dispersed copper oxide species at low Cu loadings and crystalline copper oxide species at high Cu loadings. Well-dispersed copper oxide species were reduced more easily than large copper oxide species by H(2). The results of CO(2) TPD suggest that the basicity of the catalysts was found to increase with an increase of copper loading up to 5.0 wt % and decreases with a further increase of copper loading. The results of NH(3) TPD suggest that the acidity of the catalysts was found to decrease with an increase of copper loading up to 5.0 wt % and increases with a further increase of copper loading. The catalytic properties were evaluated for the vapor-phase dehydrogenation of cyclohexanol to cyclohexanone and correlated with the results of CO(2) TPD measurements and the dispersion of Cu on the Al(2)O(3)-ZrO(2) support.     

Thermodesorption studies of energetic properties of Ni/MgO-Al2O3 catalysts. Determination of adsorption energy distribution functions

The thermodesorption spectra of hydrogen from coprecipitated catalysts (70-x)NiO-xMgO-30Al(2)O(3) (x = 0-50%(wt)) are reported. The catalysts were calcined at 400 degrees C and reduced with H(2) at 20-800 degrees C and for 3 h at 800 degrees C. NiO reduction degree was between 49.3 and 92.1%. The active surface areas changed from 8.4 to 32.4 m(2)/g whereas mean size of nickel crystallites was between 3.7 and 9.7 nm. The TPD spectra were next analyzed in order to determine the adsorption energy distributions functions. To obtain these functions a theoretical model of adsorption/desorption kinetics based on the statistical rate theory (SRT) was applied. This approach allows for determination of the adsorption energy at nonequilibrium conditions as well as at quasiequilibrium conditions. The resulting distribution functions reveal the presence of two main bands of adsorption energy. Some correlation is found between the determined distributions of adsorption energy and the size of nickel crystallites determined using the XRD method. The presence of MgO favors creation of high energy adsorption sites on Ni crystallites.     

Carbon-nitrogen place exchange on NO exposed beta-Mo2C

Atomic nitrogen and oxygen were deposited on beta-Mo(2)C through dissociative adsorption of NO. Reflectance absorbance infrared spectroscopy (RAIRS), thermal desorption, and synchrotron X-ray photoelectron spectroscopy (XPS) measurements were used to investigate the interplay between atomic nitrogen, carbon, and oxygen in the 400-1250 K region. The combination of the high resolution and high surface sensitivity offered by the synchrotron XPS technique was used to show that atomic nitrogen displaces interstitial carbon onto the carbide surface. Thermal desorption measurements show that the burnoff of the displaced carbon occurs at approximately 890 K. The incorporation of nitrogen into interstitial sites inhibits oxygen dissolution into the bulk. RAIRS spectroscopy was used to identify surface oxo, terminal oxygen, species formed from O(2) and NO on beta-Mo(2)C.