Phase transition of RbH<Subscript>2</Subscript>PO<Subscript>4</Subscript> and its composite with SiO<Subscript>2</Subscript> studied by thermal analysis

The phase transition at T _p (~109 °C) of RbH₂PO₄ and its composite with SiO₂ has been investigated by thermal analysis here. In the case of neat RbH₂PO₄, there is a linear relationship between endothermic peak temperature (T _m) and square root of heating rate (Φ ^1/2), from which the onset temperature of phase transition can be determined. Besides, Kissinger method and another calculation method were employed to obtain the activation energy of phase transition. The detailed deduction process was presented in this paper, and the estimated activation energies are E ₁ ≈ 126.3 kJ/mol and E ₂ ≈ 129.2 kJ/mol, respectively. On the other hand, the heterogeneous doping of RbH₂PO₄ with SiO₂ as dopant facilitates its proton conduction and leads to the disappearance of jump in conductivity at T _p. The heats of transition in the composites decrease gradually with increasing the molar fraction of SiO₂ additives. In the cooling process, a new and broad exothermic peak appeared between ~95 and ~110 °C, and its intensity also changes with the SiO₂ amount. These phenomena might be related to the formation of amorphous phase of RbH₂PO₄ on the surface of SiO₂ particles due to the strong interface interaction.     

Synthesis of electrospun BaSrTiO<Subscript>3</Subscript>/PVP nanofibers

Ba_1−x Sr _x TiO₃(x = 0–0.5, BST) nanofibers with diameters of 150–210 nm were prepared by using electrospun BST/polyvinylpyrrolidone (PVP) composite fibers by calcination for 2 h at temperatures in the range of 650–800 °C in air. The morphology and crystal structure of calcined BST/PVP nanofibers were characterized as functions of calcination temperature and Sr content with an aid of XRD, FT-IR, and TEM. Although several unknown XRD peaks were detected when the fibers were calcined at temperatures less than 750 °C, they disappeared with increasing the temperature (above 750 °C) due to its thermal decomposition and complete reaction in the formation of BST. In addition, the FT-IR studies of BST/PVP fibers revealed that the intensities of the O–H stretching vibration bands (at 3430 and 1425 cm⁻¹) became weaker with increasing the calcination temperature and a broad band at 540 cm⁻¹, Ti–O vibration, appeared sharper and narrower after calcination above 750 °C due to the formation of metal oxide bonds. However, no effect of Sr content on the crystal structure of the composites was detected.     

Effect of calcination temperature on the microstructure of porous TiO<Subscript>2</Subscript> film

To obtain porous TiO₂ film, the precursor sol was prepared by hydrolysis of Ti isopropoxide and then complexed with trehalose dihydrate. The porous TiO₂ film was fabricated by the dip-coating technique on glass substrates using this solution. The TiO₂ film was calcined at 500 °C. The maximum thickness of the film from one-run dip-coating was ca. 740 nm. The film was composed of nanosized particle and pores. The porosity of the TiO₂ film was increased by addition of trehalose dihydrate to the sol. The porous TiO₂ films were calcined at different temperatures. The effects of calcination temperature on the microstructure of the porous TiO₂ film were investigated. The porous film prepared from sol containing trehalose still kept the porous structure after calcination at 950 °C. The phase transition temperature of the film from anatase to rutile was shifted from 650 to 700 °C by addition of trehalose to the sol.     

Non-isothermal decomposition kinetics of NiFe<Subscript>2</Subscript>O<Subscript>4</Subscript> nanoparticles synthesized using egg white solution route

The thermal decomposition kinetics of nickel ferrite (NiFe₂O₄) precursor prepared using egg white solution route in dynamical air atmosphere was studied by means of TG with different heating rates. The activation energy (E _α) values of one reaction process were estimated using the methods of Flynn–Wall–Ozawa (FWO) and Kissinger–Akahira–Sunose (KAS), which were found to be consistent. The dependent activation energies on extent of conversions of the decomposition reaction indicate “multi-step” processes. XRD, SEM and FTIR showed that the synthesized NiFe₂O₄ precursor after calcination at 773 K has a pure spinel phase, having particle sizes of ~54 ± 29 nm.     

Glass transition and crystallization study of chalcogenide Se<Subscript>70</Subscript>Te<Subscript>15</Subscript>In<Subscript>15</Subscript> glass

Differential scanning calorimetry data at different heating rates (5, 10, 15 and 20 °C min⁻¹) of Se₇₀Te₁₅In₁₅ chalcogenide glass is reported and discussed. The crystallization mechanism is explained in terms of recent analyses developed for use under non-isothermal conditions. The value of Avrami exponent (n) indicates that the glassy Se₇₀Te₁₅In₁₅ alloy has three-dimensional growth. The average values of the activation energy for glass transition, E _g, and crystallization process, E _c, are (154.16 ± 4.1) kJ mol⁻¹ and (98.81 ± 18.1) kJ mol⁻¹, respectively. The ease of glass formation has also been studied. The reduced glass transition temperature (T _rg), Hruby’ parameter (K _gl) and fragility index (F _i) indicate that the prepared glass is obtained from a strong glass forming liquid.     

The effect of H2O on the sulfation of Havelock limestone under oxy-fuel conditions in a thermogravimetric analyser

A gas mixture representing oxy-fuel combustion conditions was employed in a thermogravimetric analyser to determine the effect of water vapor and SO₂ concentration on limestone sulfation kinetics over the temperature range of 800 to 920 °C. Here, experiments used small samples of particles (4 mg), with small particle sizes (d_p < 38 µm) and large gas flow rates (120 mL/min@NTP) in order to minimize mass transfer interferences. The gas mixture contained 5000 ppm_v SO₂, 2% O₂, and the H₂O content was changed from 0% to 25% with the balance CO₂. When water vapor was added to the gas mixture at lower temperatures (800–870 °C), the limestone SO₂ capture efficiency increased. However, as the temperature became higher, the enhancement in total conversion values decreased. As expected, Havelock limestone at higher temperatures (890 °C, 920 °C, and 950 °C) experienced indirect sulfation and reacted at a faster rate than for lower temperatures (800–870 °C) for direct sulfation over the first five minutes of reaction time. However, the total conversion of Havelock limestone for direct sulfation was generally greater than for indirect sulfation.     

Structural evolution and magnetic properties of SrFe<Subscript>12</Subscript>O<Subscript>19</Subscript> nanofibers by electrospinning

The SrFe₁₂O₁₉/poly (vinyl pyrrolidone) (PVP) composite fiber precursors were prepared by the sol-gel assisted electrospinning with ferric nitrate, strontium nitrate and PVP as starting reagents. Subsequently, the M-type strontium ferrite (SrFe₁₂O₁₉) nanofibers were derived from calcination of these precursors at 750–1,000 °C.The composite precursors and strontium ferrite nanofibers were characterized by Fourier transform infrared spectroscopy, X-ray diffraction, scanning electron microscopy and vibrating sample magnetometer. The structural evolution process of strontium ferrite consists of the thermal decomposition and M-type strontium ferrite formation. After calcined at 750 °C for 2 h the single M-type strontium ferrite phase is formed by reactions of iron oxide and strontium oxide produced during the precursor decomposition process. The nanofiber morphology, diameter, crystallite size and grain morphology are mainly influenced by the calcination temperature and holding time. The SrFe₁₂O₁₉ nanofibers characterized with diameters of around 100 nm and a necklace-like structure obtained at 900 °C for 2 h, which is fabricated by nanosized particles about 60 nm with the plate-like morphology elongated in the preferred direction perpendicular to the c-axis, show the optimized magnetic property with saturation magnetization 59 A m² kg⁻¹ and coercivity 521 kA m⁻¹. It is found that the single domain critical size for these M-type strontium ferrite nanofibers is around 60 nm.     

The microstructure and magnetic properties of Ni<Subscript>0.4</Subscript>Zn<Subscript>0.6</Subscript>Fe<Subscript>2</Subscript>O<Subscript>4</Subscript> films prepared by spin-coating method

Nickel zinc ferrite (Ni_0.4Zn_0.6Fe₂O₄) films on Si (100) substrate were synthesized using a spin-coating method. The crystallinity of the Ni_0.4Zn_0.6Fe₂O₄ films with the thickness of about 386 nm became better as the annealing temperature increased. The films have smooth surface, relatively good packing density and uniform thickness. The volatilization of Zn is serious at 900 °C. With the increase of annealing temperature, the saturation magnetization M _s increases in the temperature ranging from 400 to 700 °C, however, decreases above 700 °C, and the coercivity H _c increases in the temperature range 400–800 °C, decreases above 800 °C. After annealed at 700 °C for 2 h in air with the heating rate 2 °C/min, the film shows a maximum saturation magnetization M _s of 349 emu/cc and low coercivity H _c of 66 Oe. The M _s is higher than others which prepared by this method, however, the H _c is lower. The M _s of Ni_0.4Zn_0.6Fe₂O₄ films annealed at 700 °C increases with increasing annealing time and the H _c changes slightly.     

Effect of gamma-irradiation on surface and catalytic properties of nanocrystalline CuO,NiO and Fe<Subscript>2</Subscript>O<Subscript>3</Subscript> supported on alumina

The effect of γ-irradiation on surface and catalytic properties of CuO/Al₂O₃, NiO/Al₂O₃ and Fe₂O₃/Al₂O₃ was investigated. The techniques employed were XRD, nitrogen adsorption at −196 °C and catalytic conversion of ethanol and isopropanol at 250–400 °C using micropulse technique. The results showed that the supported solids being calcined at 400 °C consisted of well crystallized CuO, NiO, Fe₂O₃ and AlOOH phases. The AlOOH crystallized into a poorly crystalline γ-Al₂O₃ upon heating at 600 °C. All phases present in different solids calcined at 400 and 600 °C showed that these solids are of nanocrystalline nature measuring an average crystallite size between 6 and 85 nm. The crystallite size of crystalline phases present was found to be much affected by the dose of γ-rays and the nature of the metal oxide. This treatment resulted in a progressive increase in the specific surface area reaching to a maximum limit at a dose of 0.8 MGy. The dose of 1.6 MGy exerted a measurable decrease in the S _BET. A radiation dose of 0.2 to 0.8 MGy brought about a progressive significant decrease in the catalytic activity of all the catalytic systems investigated. All the catalytic systems retained their high activity upon exposure to a dose of 1.6 MGy. The rise in precalcination temperature of the systems investigated from 400 to 600 °C brought about a measurable increase in their catalytic activity in the conversion of alcohols.     

In situ synthesis and characterization of TiO<Subscript>2</Subscript> nanoarray films

Based on anodic aluminum oxide (AAO) templates prepared in different acidic solutions, highly ordered aligned titania nanotubes array films have been successfully prepared by the liquid phase deposition method. The effect of AAO template type on the microstructure of titania film have been studied. Using the template with a certain volume fraction of Al₂O₃ (less than 0.71), ordered aligned titania nanotubes were obtained, characterized with an outer diameter of 200 nm and an inner diameter of 100 nm, respectively. However, titania existed as ordered aligned nanorods with the diameter of 100 nm when the template with large volume fraction of Al₂O₃ (larger than 0.71) was used. TiO₂ thin films calcined at 400°C for 4 h have an anatase phase and exhibit good photocatalytic activity, i.e., 75% methylene blue could be degraded under ultraviolet irradiation for 2 h.     

Crystallization process analysis for Se<Subscript>0.95</Subscript>In<Subscript>0.05</Subscript> and Se<Subscript>0.90</Subscript>In<Subscript>0.10</Subscript> chalcogenide glasses using the contemporary isoconversional models

Carrying out crystallization studies for both Se_0.95In_0.05 and Se_0.90In_0.10 chalcogenide glasses under non-isothermal conditions at different heating rates, it was realized that a rate controlling process occurs where random nucleation of one- to two-dimensional growth is accompanied with the introduction of up to 10 at% In into glassy Se matrix. The crystallization kinetics together with its dimensionality has been studied using the four currently used isoconversional models (Kissinger–Akahira–Sunose, Ozawa–Flynn–Wall, Tang, and Starink). The activation energy of crystallization (E _c) has been determined using these indicated four models where a satisfactory concurrence is achieved. The value of E _c shows a decrease while increasing both the In-content as well as the extent of crystallization.     

A facile synthesis of NaNbO<Subscript>3</Subscript> powders by decomposition of ammonium niobium oxalate with sodium salt at low temperature

A facile synthesis of NaNbO₃ powders was performed by solid-state reaction at low temperature. Stoichiometric ammonium niobium oxalate and Na₂CO₃ were mixed in water and then calcined at different temperatures for various times after drying. A combination of X-ray diffraction (XRD), scanning electron microscope (SEM), Fourier transform infrared (FTIR) spectroscopy and thermogravimetric (TG) analysis was used to characterize the product and precursor compound. The XRD patterns show that single-phase NaNbO₃ powders with high crystallinity can be synthesized at 425 °C for 15 min. The particle size from XRD data is found to be about 40 nm for NaNbO₃ powders calcined at 500 °C for 3 h, which is in good agreement with SEM data. The SEM photograph shows that NaNbO₃ powders are cuboid-like and well crystallized when calcination at 800 °C for 3 h. The product compositions prepared using other sodium reactants, such as HCOONa and NaNO₃, are also discussed.     

Synthesis of homogeneous La<Subscript>1 − <Emphasis Type="Italic">x</Emphasis></Subscript>Ca<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript>MnO<Subscript>3</Subscript> solid solutions by the Pechini method and their activity in methane oxidation

Homogeneous La_{1 − x} Ca _x MnO₃ solid solutions have been synthesized by the Pechini method (using polymer-solid compositions). Their microstructure, stability at high temperatures, and catalytic activity in methane oxidation are reported. A continuous series of solid solutions stable in air up to 1100°C forms in the system, and the particle surface is enriched with calcium. A distinctive microstructural feature of the particles is their microporosity. The catalytic activity of all calcium-containing samples (except for x = 0.7) below 700°C is lower than that of lanthanum manganite and decreases under the action of the reaction medium, which can be due to the decrease in the amount of weakly bound oxygen on the surface because of the enrichment of the surface with calcium and the formation of strongly bound surface carbonates. The higher activity and stability of the La_0.3Ca_0.7MnO₃ sample (calcined at 1100°C) above 500°C can be due to the formation of nanosized areas with an Mn₃O₄ structures on the perovskite particle surface in the reaction medium.     

Synthesis,crystal structure,and thermal decomposition kinetics of complex [Nd(BA)<Subscript>3</Subscript>bipy]<Subscript>2</Subscript>

The complex of [Nd(BA)₃bipy]₂ (BA = benzoic acid; bipy = 2,2′-bipyridine) has been synthesized and characterized by elemental analysis, IR spectra, single crystal X-ray diffraction, and TG/DTG techniques. The crystal is monoclinic with space group P2(1)/n. The two–eight coordinated Nd³⁺ ions are linked together by four bridged BA ligands and each Nd³⁺ ion is further bonded to one chelated bidentate BA ligand and one 2,2′-bipyridine molecule. The thermal decomposition process of the title complex was discussed by TG/DTG and IR techniques. The non-isothermal kinetics was investigated by using double equal-double step method. The kinetic equation for the first stage can be expressed as dα/dt = A exp(−E/RT)(1 − α). The thermodynamic parameters (ΔH ^≠, ΔG ^≠, and ΔS ^≠) and kinetic parameters (activation energy E and pre-exponential factor A) were also calculated.     

Chemo-bio catalyzed synthesis of <Emphasis Type="Italic">R</Emphasis>-1-phenylethyl acetate over bimetallic PdZn catalysts,lipase, and Ru/Al<Subscript>2</Subscript>O<Subscript>3</Subscript>. part I

One-pot synthesis of R-1-phenyethylacetate at 70°C was investigated using three different catalysts simultaneously, namely a bimetallic PdZn/Al₂O₃ as a hydrogenation catalyst, an immobilized lipase as an acylation catalyst and Ru/Al₂O₃ as a racemization catalyst. The most active bimetallic catalyst was PdZn/Al₂O₃ calcined at 300°C and reduced at 400°C, whereas the most selective although less active catalyst was the one being calcined and reduced at 500°C. The highest selectivity to R-1-phenylethyl acetate over this catalyst was 32 at 48% conversion. Ru/Al₂O₃ was confirmed to have a positive effect on the formation of the desired product, although it was not very active in the racemization during one-pot synthesis.     

Preparation and electrical properties of Nd and Mn co-doped Bi<Subscript>4</Subscript>Ti<Subscript>3</Subscript>O<Subscript>12</Subscript> thin films

Ferroelectric thin films of Nd and Mn co-doped bismuth titanate, Bi_3.15Nd_0.85Ti_3−x Mn _x O₁₂ (BNTM) (x = 0–0.1), were fabricated on Pt/TiO₂/SiO₂/Si(100) substrates by a sol–gel technique. The BNTM films had a polycrystalline perovskite structure and uniform and dense surface morphologies. A lattice distortion was observed in the BNTM films due to Mn ion doping. The ferroelectric measurement of the films indicated that the values of coercive field (E _c ) decreased gradually with the increase of the Mn content (x), however, the remanent polarization (P _r ) increase firstly and then decrease with the increase of x. The sample with x = 0.05 had optimum electrical properties and a maximum 2P _r value. The 2P _r and 2E _c values of the film at a maximum applied electric field of 400 kV/cm were 38.3 μC/cm² and 180 kV/cm, respectively. Moreover, this BNTM capacitors did not show fatigue behaviors after 1.0 × 10¹⁰ switching cycles at a frequency of 1 MHz, suggesting a fatigue-free character. The main reason for the increase of the 2P _r and the decrease of the 2E _c might be attributed to the lattice distortion in BNTM films due to Mn ion doping.     

Synthesis,characterization and olefin hydroformylation reactions of <Emphasis Type="Italic">mer</Emphasis>-[Mo(CO)<Subscript>3</Subscript>(p-C<Subscript>5</Subscript>H<Subscript>4</Subscript>N-CN)<Subscript>3</Subscript>]

Mer-[Mo(CO)₃(p-C₅H₄N-CN)₃] was prepared by UV-irradiation of a THF solution of Mo(CO)₆ and para-cyanopyridine under heating. The complex was characterized by FT-IR, MS, ¹H and ¹³C NMR and showed catalytic activity for olefin hydroformylation (1-hexene, cyclohexene and 2,3-dimethyl-2-butene as model olefins; 600 psi synthesis gas (pCO/pH₂ = 1); 100 °C; 24 h; toluene). An examination of the complex catalyzed hydroformylation of a real naphtha cut (El Palito refinery, Venezuela), under the same conditions, also showed activity in the conversion to oxygenated products.     

Evaluation of thermodynamic and kinetic stability of CuAlO<Subscript>2</Subscript> and CuGaO<Subscript>2</Subscript>

Thermodynamic and kinetic stabilities of CuAlO₂ and CuGaO₂ have been evaluated by using thermogravimetry and thermodynamic calculations. It has been revealed that CuAlO₂ and CuGaO₂ are not thermodynamically stable in air below 800 °C and 1,200 °C, respectively, and that the oxidation reaction, 4CuMO₂ + O₂ → 2CuO + 2CuM₂O₄ (M = Al, Ga), should occur if the reaction kinetics are high enough. However, rate constants and activation energies indicated slow kinetics of the oxidation reaction, showing kinetic stability of CuMO₂ even under some thermodynamically unstable temperatures and atmospheres. It was also concluded that CuAlO₂ showed higher thermodynamic and kinetic stability than CuGaO₂.     

Improving Enzymatic Production of Ginsenoside Rh<Subscript>2</Subscript> from Rg<Subscript>3</Subscript> by using Nonionic Surfactant

In this study, several nonionic surfactants were tried to improve the enzymatic hydrolysis of ginsenoside Rg₃ into Rh₂ which was catalyzed at 50 °C and pH 5.0 by a crude glucosidase extracted from Fusarium sp. ECU2042. Among the biocompatible nonionic surfactants, polyethylene glycol 350 monomethyl ether was shown to be the best. After optimizing some influencing factors on the reaction, the conversion of Rg₃ (5 g/l) with 10 g/l crude enzyme reached almost 100% in the presence of the nonionic surfactant (7.5%, w/v), which was 25% higher than that in buffer without any surfactant. Furthermore, the enzyme stability was affected faintly by the surfactant.     

Some studies on the phase formation and kinetics in TiO<Subscript>2</Subscript> containing lithium aluminum silicate glasses nucleated by P<Subscript>2</Subscript>O<Subscript>5</Subscript>

Lithium aluminum silicate (LAS) glasses of compositions (wt%) 10.6Li₂O–71.7SiO₂–7.1Al₂O₃–4.9K₂O–3.2B₂O₃–1.25P₂O₅–1.25TiO₂ were prepared by the melt quench technique. Crystallization kinetics was investigated by the method of Kissinger and Augis–Bennett using differential thermal analysis (DTA). Based on the DTA data, glass ceramics were prepared by single-, two-, and three-step heat treatment schedules. The interdependence of different phases formed, microstructure, thermal expansion coefficient (TEC) and microhardness (MH) was investigated using X-ray diffraction (XRD), scanning electron microscopy (SEM), thermo-mechanical analysis (TMA), and microhardness (MH) measurements. Crystallization kinetics revealed that Li₂SiO₃ is the kinetically favored phase with activation energy of 91.10 kJ/mol. An Avrami exponent of n = 3.33 indicated the dominance of bulk crystallization. Based upon the formation of phases, it was observed that the two-stage heat treatment results in highest TEC glass ceramics. The single-step heat treatment yielded glass ceramics with the highest MH.