Hydrogen annealing effects on polycrystalline La0.67Ba0.33MnO3 compound

Upon annealing polycrystalline La_0.67Ba_0.33MnO₃ bulk samples in flowing 95%Ar:5%H₂ mixed gas at 700 °C for different time, the insulator–metal transition temperature, _TP$T_{\mathrm{P}}$ and the amplitude of AC magnetic susceptibility were decreased first, then increased, finally decreased again. While the resistivity was increased monotonically. This anomalous behavior was explained by the combinational effects of oxygen loss and Ba ion vacancies caused by the segregation of Ba ion related impurity phase.     

Anomalous paramagnetic behavior in the paramagnetic phase of La2/3−xYxCa1/3MnO3 studied through EPR and its relation to colossal magnetoresistance

Electron paramagnetic resonance on La_2/3−xY_xCa_1/3MnO₃ in the paramagnetic (PM) regime is presented for 0≤x≤0.133. The resonance linewidth (ΔH_pp) decreases with cooling, reaches the minimum at T_min, and then anomalously increases with further cooling toward T_c. Our analysis on ΔH_pp(T) below T_min shows that the anomalous PM behavior below T_min is due to the appearance of a ferromagnetic (FM) phase within the PM matrix caused by the applied magnetic fields. The correlation between the anomalous PM and the colossal magnetoresistance is discussed. We argue that both are caused by the phase segregation in which the compound is phase-separated into a mixture of FM and PM regions.     

Atomistic computer simulation studies of La1−xSrxVO3

Static computer simulation techniques have been employed for structural investigation of the La_1−xSr_xVO₃ series. Potential parameters for V³⁺-O²⁻ and V⁴⁺-O²⁻ have been derived which reproduces the crystal structures of end members with sufficient accuracy. Variations of lattice parameters and bond distances with Sr concentration have been studied. The calculated lattice parameters decrease with increase in the Sr concentration. A structural phase transition from orthorhombic to cubic is observed at 50% Sr doping level.     

Optical investigations of polycrystalline Mg1−xB2 near metal-insulator transition

We measured reflectivity spectra of polycrystalline Mg_1−xB₂ samples, which show a metal-insulator transition with x. After performing the Kramers-Kronig analysis, the obtained optical conductivity spectra σ(ω) of MgB₂ show a narrow Drude peak in the far-infrared region and a broad peak in the mid-infrared region. As x increases, the spectral weight of the Drude peak is strongly suppressed and that of the broad peak becomes enhanced a little. The existence of the broad mid-infrared peak in the insulating sample suggests that this peak might not be related to the free carriers in MgB₂. In the far-infrared region, we also observe that the low energy dielectric constant of Mg_1−xB₂ diverges near the metal-insulator phase boundary (i.e. x=0.08). This result implies the possibility of a phase separation and a percolative metal-insulator transition in Mg_1−xB₂.     

Spray-pyrolysis deposition of LaMnO3 and La1−xCaxMnO3 thin films

Ethylene glycol solutions of La-Mn(II) and La-Ca-Mn(II) citric complexes has been used as a starting material for spray-pyrolysis deposition of LaMnO₃ and La_1−xCa_xMnO₃ thin films on β-quartz, fused quartz, Si(0 0 1) and SrTiO₃(1 0 0) substrates heated during the deposition at 380 °C. At suitable post-deposition heating conditions highly uniform films, 0.1-1 μm in thickness, with good crystal structure were obtained. Highly textured LaMnO₃ films are obtained on SrTiO₃(1 0 0) substrate. Interaction between the layer and Si-containing substrates is observed during the post-deposition heating in static air.     

Thermal conductivity of La0.67(CaxSr1−x)0.33MnO3 (x=0, 0.5, 1) and La0.6Y0.07Ca0.33MnO3 pellets between 10 and 300 K

Thermal conductivity (λ) of nanocrystalline La_0.67(Ca_xSr_1−x)_0.33MnO₃ (x=0, 0.5, 1) and La_0.6Y_0.07Ca_0.33MnO₃ pellets prepared by a novel ‘pyrophoric’ method have been studied between the temperature range 10 and 300 K. Our data show that the magnitude of thermal conductivity is strongly influenced by the ion substitutions at La-site. The analysis of the thermal conductivity data indicates that the thermal transport is governed largely by phonons scattering in these systems and the electronic contribution is as small as 0.2-1% of total thermal conductivity (λ_total). At low temperatures (<90 K) 2D like lattice defects contribute to the phonon scattering dominantly and its strength increases with increasing Sr content and also with partial substitution of La by Y. Depending upon the composition of the samples, the magnon thermal conductivity contributes 2-15% of λ_total close to T_C. In the paramagnetic regime the unusual increase in λ_total keeps signature of large dynamic lattice distortion.     

Charge order melting and magnetic transition in Nd0.5(1+x)Ca0.5(1−x)Mn(1−x)CrxO3 system

The magnetic property of double doped manganite Nd_0.5(1+x)Ca_0.5(1−x)Mn_(1−x)Cr_xO₃ with a fixed ratio of Mn³⁺:Mn⁴⁺=1:1 has been investigated. For the undoped sample, it undergoes one transition from charge disordering to charge ordering (CO) associated with paramagnetic (PM)-antiferromagnetic (AFM) phase transition at T<250 K. The long range AFM ordering seems to form at 35 K, rather than previously reported 150 K. At low temperature, an asymmetrical M-H hysteresis loop occurs due to weak AFM coupling. For the doped samples, the substitution of Cr³⁺ for Mn³⁺ ions causes the increase of magnetization and the rise of T_c. As the Cr³⁺ concentration increases, the CO domain gradually becomes smaller and the CO melting process emerges. At low temperature, the FM superexchange interaction between Mn³⁺ and Cr³⁺ ions causes a magnetic upturn, namely, the second FM phase transition.     

Open atmosphere synthesis and wide range colossal magnetoresistance in La0.7Sr0.3−xHgxMnO3 (0≤x≤0.2) system

We have synthesized several polycrystalline samples with nominal compositions La_0.7Sr_0.3−xHg_xMnO_3+δ (0≤x≤0.2) by the standard solid-state reaction method. Instead of the sealed quartz tube method widely employed for the Hg-based systems, we adopted open atmosphere synthesis route. All the samples exhibited monophasic nature with rhombohedral structure as revealed by the X-ray diffraction data. A variation in the unit cell volume is observed with x, which is interpreted as a result of extra oxygen in-diffusion and subsequent cation vacancy creation. A broad metallic behavior is seen in the entire temperature range from 300 to 4 K. The samples showed varying amount of colossal magnetoresistance depending upon the temperature and applied magnetic field. The MR value as high as 30% was observed in x=0.2 sample and the MR is persistent over a wide temperature range with a little change in magnitude.     

Study of the magnetization and transport properties of the La(2+x)/3Sr(1−x)/3Mn1−xCrxO3 (0≤x≤0.2) system

The samples with the Mn³⁺/Mn⁴⁺ ratio fixed at 2:1 La_(2+x)/3Sr_(1−x)/3Mn_1−xCr_xO₃ (0≤x≤0.20) have been prepared. The magnetic, electrical transport, and magnetoresistance properties have been investigated. Remarkable transport and colossal magnetoresistance (CMR) effect, as well as cluster glass (CG) behaviors have been clearly observed in the samples studied. It was found that the Curie temperature T_c and insulator−metal transition temperature T_p1 are strongly affected by Cr substitution. The experiment observations are discussed by taking into account the variety of tolerance factors t; the effects of A-site radius 〈r_A〉 and the A-site mismatch effect (σ²).     

Effects of low frequency near metal-insulator transition temperatures on polycrystalline La0.65Ca0.35Mn1−yFeyO3 (where y=0.05-0.10) ceramic oxides

The ac electrical properties of 5-10% Fe doped polycrystalline sample have been investigated by complex impedance analysis over the frequency and temperature ranges of 1-100 kHz and 77-300 K, respectively. The average normalized change (ΔZ′/Δf)/Z₀ has been deduced for these Fe doped CMR samples which shows an increasing trend with iron doping. The most pronounced effect of frequencies is at T_c, with the increase of Fe doping it is observed that not only T_c is lowered substantially but also the height of the peaks of real part of impedance (Z′) is increased which in turn decreases considerably with the increase of the ac field. An equivalent circuit model, R_g(R_gbC_gb), i.e. a resistor-capacitor network, has been proposed to explain the impedance results at different temperatures. The plot between τ and 1/T gives a straight line from where relaxation time (τ₀) has been deduced. The correlated barrier hopping (CBH) model has been employed and the binding energy of the defect states is estimated to be between 0.39 and 0.25 eV while the minimum hoping distance varies within the range of 2.93-5.21 Å for these 5-10% Fe doped LCM samples.     

Lanthanum deficiency effect in magnetic transition and transport property of La0.8−δCa0.2MnO3

The evolution of magnetic and electrical phases in La_0.8−δCa_0.2MnO₃ was investigated in terms of La deficiency. We found that the increase of the La deficiency tends to raise the Curie temperature (T_C) in La_0.8−δCa_0.2MnO₃. The FM clusters formed in compounds with large La deficiency provide percolation paths above T_C. With increasing the La defect, the transport property changes from insulating to metallic state, which is in association with the crossover from a second order to a first order magnetic phase transition in the vicinity of T_C.     

Large room temperature magnetoresistance in YSZ doped La0.67Ba0.33MnO3 composite

The temperature dependence of the resistivity for composite samples of (1−x)La_0.67Ba_0.33MnO₃+xYSZ(LBMO/YSZ) with different YSZ doping level of x has been investigated in a magnetic field range of 0-7000 Oe, where the YSZ represents yttria-stabilized zirconia (8 mol% Y₂O₃+92 mol% ZrO₂). With increasing YSZ doping level, the range of 0-10%, the metal-insulator transition temperature (T_P) decreases. However, the resistivity, specially the low temperature resistivity, increases. Results also show that the YSZ doping level has an important effect on a low field magnetoresistance (LFMR). In the magnetic field of 7000 Oe, a room temperature magnetoresistance value of 20% was observed for the composite with a YSZ doping level of 2%, which is encouraging for potential application of CMR materials at room temperature and low field.     

Structure, magnetic, and transport properties of the Co-doped manganites La0.9Te0.1Mn1−xCoxO3 (0≤x≤0.25)

The effect of Co doping at Mn-site on the structural, magnetic and electrical transport properties in electron-doped manganties La_0.9Te_0.1Mn_1−xCoxO₃ (0≤x≤0.25) has been investigated. The room temperature structural transition from rhombohedra to orthorhombic (Pbnm) symmetry is found in these samples with x≥0.20 by the Rietveld refinement of X-ray powder diffraction patterns. All samples undergo the paramagnetic-ferromagnetic (PM-FM) phase transition. The Curie temperature T_C of these samples decreases and the transition becomes broader with increasing Co-doping level. The magnetization magnitude of Co-doping samples increases at low temperatures with increasing Co-doping level for x≤0.15 and decreases with increasing Co-doping content further. The metal-insulator (M-I) transitions observed in the sample with x=0 are completely suppressed with Co doping, and the resistivity displays semiconducting behavior within the measured temperature region for these samples with x>0. All results are discussed according to the changes of the structure parameters and magnetic exchange interaction caused by Co-doping. In addition, the different effects between the Co doping and Cu doping in the Mn site for the electron-doped manganites are also discussed.     

Positron annihilation lifetime studies on La0.5Pb0.5Mn1−yCryO3

Concentration dependent positron annihilation lifetime (PAL) measurements on Cr doped La_0.5Pb_0.5Mn_1−yCr_yO₃ (y=0.075, 0.15, 0.3, 0.35, 0.45) samples showing metal-insulator transitions (MIT) between 178 and 276 K (depending on y) reveal anomalous variation of average and bulk PAL, τ_av and τ_B, respectively, around y=0.35. Such anomaly has not, however, been observed from the corresponding magnetic susceptibility and resistivity data. Interestingly, the model parameters (polaron radius, number of ion sites per unit volume) obtained from fitting the high temperature (above MIT, T_p) resistivity data with small polaron hopping model show the signature of the said anomaly around the same concentration. Nonlinear variations of τ_av and τ_B support the existence of small polarons (T>T_p) which act as defect centers in such rare-earth manganites. Analysis of X-ray diffraction pattern confirms a change of lattice parameters indicating a structural transformation from rhombohedral (for y≤0.30) to orthorhombic (for y≥0.35) in the present system.     

Electrical transport and magnetic properties of La2/3Ca1/3MnO3/SiO2 composites

The influence of SiO₂ on the electrical transport properties of LCMO/SiO₂ composites with different SiO₂ contents x is investigated, where LCMO represents La_2/3Ca_1/3MnO₃. Results show that the SiO₂ phase not only shifts the metal–insulator transition temperature (T_p) to a high temperature range, but also has an effect on the magnetoresistance (MR) of the composites. The temperature dependence of resistivity indicates that the T_p of the composites is obviously higher than that of pure LCMO, and that the peak resistivity ρ_max of the composites is lower than that of pure LCMO. In the SiO₂ content x∼0.02, the T_P is the highest and ρ_max becomes the lowest. The experimental observation is discussed on the basis of the analysis of scanning electron microscopy (SEM) images and X-ray diffraction (XRD) patterns. Compared with pure LCMO, a possible interpretation is presented by considering the influence of SiO₂ on the coupling between ferromagnetic (FM) domains of LCMO.     

La1−xCaxCoO3 perovskite-type oxides: Identification of the surface oxygen species by XPS

A detailed study of the La_1−xCa_xCoO₃ perovskites surface by XPS was carried out since this is a potentially useful tool to identify the oxygen species involved in the catalytic reaction and discriminate them. Mainly, the concentration of surface oxygen vacancies (λ′) can be estimated from the XPS atomic ratio.     

The correlation between structure and magnetic properties in the manganites La0.7Ca0.3−xTexMnO3 (0≤x≤0.15)

The effect of Te-doping at La-site on structural, magnetic and transport properties in the manganites La_0.7Ca_0.3−xTe_xMnO₃ (0≤x≤0.15) has been investigated. All samples show an orthorhombic structure (O′-Pbnm) at room temperature. It shows that the Mn-O-Mn bond angle decreases and the Mn-O bond length increases with the increase in the Te content. All samples exhibit an insulator-metal (I-M) transition and the resistivity increases with the increase in the Te-doping level. Additionally, the Curie temperature T_c decreases and the transition becomes broader with increasing Te-doping level, in contrast, the magnetization of Te-doping samples at low temperatures decrease with increasing x as x≤0.10 and then increase with further increasing x to 0.15. The results are discussed in terms of Jahn-Teller (JT) vibrational anisotropy Q₃/Q₂ and the opening of the new DE channel between Mn²⁺-O-Mn³⁺ due to the introduction of Mn²⁺ ions because of the substitution of Te⁴⁺ ions for Ca²⁺ ions.     

Structural, magnetic and transport properties in the manganites La0.7Sr0.3−xTexMnO3 (0≤x≤0.15)

The effect of Te-doping at La-site on structural, magnetic and transport properties in the manganites La_0.7Sr_0.3−xTe_xMnO₃ (0≤x≤0.15) has been investigated. All samples show a rhombohedral structure with the space group . It shows that the Mn-O-Mn bond angle decreases and the Mn-O bond length increases with the increase of Te content. The Curie temperature T_C decreases with increasing Te-doping level, in contrast, the magnetization magnitude of Te-doping samples at low temperatures increase with increasing x as x≤0.05 and then decrease with further increasing x to 0.15. The results are discussed in terms of the combined effects of the opening of the new double exchange (DE) channel between Mn²⁺-O-Mn³⁺ due to the introduction of Mn²⁺ ions because of the substitution of Te⁴⁺ for Sr²⁺ and the reduction of the transfer integral b due to the decrease of the Mn-O-Mn bond angle.     

Electronic structure and ferromagnetism of polycrystalline Zn1−xCoxO (0≤x≤0.15)

The electronic structure of polycrystalline ferromagnetic Zn_1−xCo_xO (0.05≤x≤0.15) and the oxidation state of Co in it, have been investigated. The Co-doped polycrystalline samples are synthesized by a combustion method and are ferromagnetic at room temperature. XPS and optical absorption studies show evidence for Co²⁺ ions in the tetrahedral symmetry, indicating substitution of Co²⁺ in the ZnO lattice. However, powder XRD and electron diffraction data show the presence of Co metal in the samples. This give evidence to the fact that some Co²⁺ ion are incorporated in the ZnO lattice which gives changes in the electronic structure whereas ferromagnetism comes from the Co metal impurities present in the samples.     

Ferroelectric properties of Bi3.25−x/3La0.75Ti3−xNbxO12 films prepared by pulsed laser deposition

Bi₄Ti₃O₁₂ (BiT), Bi_3.25La_0.75Ti₃O₁₂ (BLT), Bi_4−x/3Ti_3−xNb_xO₁₂ (BTN) and Bi_3.25−x/3La_0.75Ti_3−xNb_xO₁₂ (BLTN) thin films have been prepared by pulsed laser deposition. BTN and BLTN films exhibit a maximum in the remanent polarization P_r at a Nb content x=0.018. At this Nb content, the BLTN film has a P_r value (25 μC/cm²) that is much higher than that of BiT and a coercive field similar to that of BiT. The polarization of this BLTN film is fatigue-free up to 10⁹ switching cycles. The high fatigue resistance is mainly due to the substitution of Bi³⁺ ions by La³⁺ ions at the A site and the enhanced P_r arises largely from the replacement of Ti⁴⁺ ions by Nb⁵⁺ ions at the B site. The mechanisms behind the effects of the substitution at the two sites are discussed.