Electrical and magnetic properties of non-stoichiometric (La0.8Sr0.2)1−xMnO3 perovskites

The structure, transport and magnetic properties of (La_0.8Sr_0.2)_1−xMnO₃ (0≤x≤0.30) polycrystalline perovskite manganites have been investigated. For all the samples the Curie temperatures, T_c, remain nearly unchanged (329±3 K). Resistivity versus temperature curves for the samples show a double-peak behavior. A significant magnetoresistance (MR) effect and different temperature dependences of the MR ratios of the samples are observed. The shapes of the MR-T curves of the samples can be adjusted by changing x. For the x=0.30 sample, a nearly constant MR ratio of (9.5±0.5)% is obtained over the temperature range from 205 to 328 K.     

Magnetoresistance in La1−xCaxMnO3 (0≤x<0.4)

The magnetic and transport properties of La_1−xCa_xMnO₃ (0≤x<0.4) have been systematically studied. The magnetoresistance (MR) maximum appears at x=0.2-0.25 and the temperature dependence of MR for x>0.25 shows a much broader profile than that of samples for x=0.2-0.25. Based on a scenario in which there is a short-range charge ordering (CO) state coexisting in the ferromagnetic state matrix for x>0.25, and the least or even no short-range CO state exists in samples for x=0.2-0.25, the above observations can be understood.     

Magnetic and transport property studies of nanocrystalline ZnxFe3−xO4

The magnetic and transport properties of nanocrystalline Zn_xFe_3−xO₄ with x=0.0, 0.2, 0.4, 0.5, 0.6, 0.8 and 1.0, respectively, fabricated by the sol-gel method have been investigated. Large magnetoresistance (MR) was observed and found to be originated both from the tunneling of the spin-polarized electrons across the adjacent ferromagnetic grains and the scattering by the canted spins at the grain surface near the grain boundaries. It has been revealed that the MR for the Zn_xFe_3−xO₄ samples (x=0, 0.5 and 1.0) increases with the temperature decreasing from room temperature until a maximum is reached at around 55 K. Then a sharp drop occurs with the further decrease in temperature, regarded as a spin (cluster) glass transition. For the samples studied, a biggest low field (0.5 T) MR value of about 20% for x=0 at 55 K has been obtained. The mechanism of the MR behavior of the materials was discussed.     

Large magnetoresistance in low temperature metallic region of manganite compounds (La0.7−2xEux)(Ca0.3Srx)MnO3 (0.05≤x≤0.15)

Magnetoresistance (MR) and magnetization (dc and ac) measurements have been carried out on the manganites, (La_0.7−2xEu_x)(Ca_0.3Sr_x)MnO₃ (0.05≤x≤0.15), in the temperature range of 5-320 K. At 5 K, an unusually large MR of almost 98% is observed in the x=0.15 sample, nearly up to fields of 4-5 T. This large high-field MR occurs in the metallic region, far below the insulator-metal transition temperature, and does not vary linearly with applied field. The unusual magnetoresistance is explained in the light of various possibilities such as phase segregation, cluster spin-glass behavior, etc.     

Structural, transport, and magnetic properties in the Ti-doped manganites LaMn1−xTixO3 (0≤x≤0.2)

The magnetism and transport properties of the samples LaMn_1−xTi_xO₃ (0≤x≤0.2) were investigated. All samples show a rhombohedral structure () at room temperature. The sample with x=0 undergoes the paramagnetic-ferromagnetic (PM-FM) transition accompanied by an insulator-metal (I-M) transition due to the oxygen excess. The doped samples show ferromagnetism and cluster behavior at low temperatures. Though no I-M transition associated with the PM-FM transition appears, the magnetoresistance (MR) effect was observed especially at low temperatures under the applied fields of 0.5 T. Due to the fact that the oxygen content in the Ti-doped samples is nearly stochiometry (3.01) and the Hall resistivity at room temperature is negative, the ferromagnetism in LaMn_1−xTi_xO₃ (0.05≤x≤0.2) is believed to be consistent with the Mn²⁺-O-Mn³⁺ double exchange (DE) mechanism. These results suggest that DE can be obtained by direct Mn-site doping.     

Electron diffraction evidence of charge-ordering at room-temperature in La1−xCaxMnO3 (0.55≤x≤0.67)

Temperature dependent electron diffraction of La_1−xCa_xMnO₃ for 0.55≤x≤0.67 using transmission electron microscope (TEM) has been carried out in the temperature range of 106-300 K to study the melting of charge-ordering across the transition temperature. Clear signature of charge-ordering as evident by the presence of diffuse super-lattice spots persist even at room temperature. This has been consistently observed for four different samples with compositions within the range of 0.55≤x≤0.67. The results indicate emergence of some degree of itinerancy in the localized charge carriers as temperature rises.     

Structure and superconductivity of Mg1−xPbxB2

A series of polycrystalline samples of Mg_1−xPb_xB₂ (0≤x≤0.10) were prepared by a solid state reaction method and their structure, superconducting transition temperature and transport properties were investigated by means of X-ray diffraction (XRD) and resistivity measurements. Mg_1−xPb_xB₂ compounds were shown to adopt an isostructural AlB2-type hexagonal structure in a relatively small range of lead concentration, x≤0.01. The crystalline lattice constants were evaluated and were found to exhibit slight length compression as x increases. The superconducting transition temperature (T_c) steadily decreases with Pb doping. It is suggested that the mechanism of superconductivity reduction by lead doping can be attributed to the chemical pressure effect.     

Disorder induced ferromagnetism in the Cu-doped molybdate SrMo1−xCuxO3 (0≤x≤0.20)

The effect of Cu-doping at Mo-site on structural, magnetic, electrical transport and specific heat properties in molybdates SrMo_1−xCu_xO₃ (0≤x≤0.2) has been investigated. The Cu-doping at Mo-site does not change the space group of the samples, but decreases the structural parameter a monotonously. The magnetic properties change from Pauli-paramagnetism for x=0 to exchange-enhanced Pauli-paramagnetism for x=0.05 and 0.10, and then ferromagnetism for x=0.15 and 0.20. All samples exhibit metallic-like transport behavior in the whole temperature range studied. The magnitude of resistivity increases initially to x=0.10 and then decreases with increasing Cu-doping concentration. The results are discussed according to the electron localization due to the disorder effect induced by the random distribution of Cu at Mo site in the samples. In addition, the temperature dependence of specific heat for the Cu-doped sample has also been studied.     

The magnetic behavior of La1−xTbxMn2Si2 (0≤x≤0.3) in weak magnetic fields

The structure and magnetic properties of La_1−xTb_xMn₂Si₂ (0≤x≤0.3) were studied by X-ray powder diffraction and DC magnetization measurements. All the compounds crystallize in ThCr₂Si₂-type structure. Substitution of Tb for La led to a linear decrease in the lattice constants and the unit-cell volume. A ferromagnetic phase for x≤0.15, and an antiferromagnetic phase for x=0.3 have been observed at about room temperature, whereas the compounds with x=0.2 and 0.25 exhibit a magnetic phase transition from ferromagnetism to antiferromagnetism.     

Study of (Bi2O3)(BaxMo1−xO3) polycrystalline ceramic as relaxor ferroelectric

Solid solutions of bismuth layered (Bi₂O₃)(Ba_xMo_1−xO₃) (0.2≤x≤0.8, x is in step of 0.2) ceramics were prepared by conventional solid-state reaction of the constitutive oxides at optimized temperatures with a view to study its electrical properties. Powder X-ray diffraction has been employed for physical characterization and an average grain size of ∼16 to 22 nm was obtained. XRD study reveals the single phase structure of the samples. Dielectric properties such as dielectric constant (ε′), dielectric loss (tanδ) and ac electrical conductivity (σ_ac) of the prepared ceramics sintered at various temperatures in the frequency range 10¹–10⁷ Hz have been studied. A strong dispersion observed in the dielectric properties shows the relaxor type behavior of the ceramic. The presence of maxima in the dielectric permittivity spectra indicates the ferroelectric behavior of the samples. Impedance plots (Cole–Cole plots) at different frequencies and temperatures were used to analyze the electric behavior. The value of grain resistance increases with the increase in Ba ion concentration. The conductivity mechanism shows a frequency dependence, which can be ascribed to the space charge mainly due to the oxygen vacancies. The relaxation observed for the M″ (ω) or Z″ (ω) curves is correlated to both localized and long range conduction. A single ‘master curve’ for the normalized plots of all the modulus isotherms observed for a given composition indicates that the conductivity relaxation is temperature independent.     

Structural and magnetic properties of sol-gel Co2xNi0.5−x Zn0.5−xFe2O4 thin films

Nanocrystalline Co_2xNi_0.5−xZn_0.5−xFe₂O₄ (x=0−0.5) thin films have been synthesized with various grain sizes by a sol-gel method on polycrystalline silicon substrates. The morphology as well as magnetic and microwave absorption properties of the films calcined at 1073 K were studied using X-ray diffraction, scanning electron microscopy, X-ray photoelectron spectroscopy, and vibrating sample magnetometry. All films were uniform without microcracks. The Co content in the Co-Ni-Zn films resulted in a grain size ranging from 15 to 32 nm while it ranged from 33 to 49 nm in the corresponding powders. Saturation and remnant magnetization increased with increase in grain size, while coercivity demonstrated a drop due to multidomain behavior of crystallites for a given value of x. Saturation magnetization increased and remnant magnetization had a maximum as a function of grain size independent of x. In turn, coercivity increased with x independent of grain size. Complex permittivity of the Co-Ni-Zn ferrite films was measured in the frequency range 2-15 GHz. The highest hysteretic heating rate in the temperature range 315-355 K was observed in CoFe₂O₄. The maximum absorption band shifted from 13 to 11 GHz as cobalt content increased from x=0.1 to 0.2.     

Structural, optical and dielectric studies of NixZn1−xFe2O4 prepared by auto combustion route

Ni_xZn_1−xFe₂O₄ (0≤x≤1) powders were synthesised by the auto combustion method. The derived samples show well defined peaks of cubic spinal structure with space group Fd3m. The lattice parameter calculated increased from 0.8372 nm to 0.8429 nm with raise of Zn content. The average crystallite sizes were determined by using Debye-Scherer method and found to be in the range of 18-23 nm. Microstructural analyses show the regular and uniform grain morphology. Raman analyses demonstrated that the peaks have symmetric and asymmetric stretching as well as symmetric bending. Fourier transform infrared spectroscopy was used to investigate the structure and shows the changes in the tetrahedral and octahedral bond stretching. Photoluminescence measurements indicated intense emission in the wavelength range lie in blue-green region. The composition with x=0.2 showed highest intensity and explained on the basis of disordered cluster model. Dielectric analyses showed frequency sensitive behaviour in the low frequency region and frequency independent characteristics at high frequency side. The composition with x=0.2 showed highest dielectric constant and lowest dielectric loss in the studied frequency range. The ac conductivity showed a power law behaviour and conduction is explained on the basis of hoping mechanism.     

Reply to the comment on: ‘Magnetoresistance in La1−xCaxMnO3(0≤x<0.4)’

The author of the comment objects to the characterization and the interpretation of magnetoresistance (MR) effects observed by us in La_1−xCa_xMnO₃ (0≤x<0.4) samples. In this reply, arguments are used to show that the samples' characterization and explanation of the MR by considering the role of the short-charge ordering (CO) regions and magnetic domains are reasonable and acceptable.     

Study of structural, transport and magneto-resistive properties of La0.7Ca0.3−xCexMnO3 (0≤x≤0.2)

We have synthesized a series of La_0.7(Ca_0.3−xCe_x)MnO₃ (0≤x≤0.2) by standard solid-state reaction method. X-ray diffraction (XRD) measurement was carried out for structural studies and Rietveld refinement was done for structural analysis. The transport properties were studied using four probe technique. The temperature dependence of the resistivity was measured in the temperature range of 20 K to room temperature. It is found that all samples show a systematic variation in metal to insulator transition at transition temperature (T_P) and resistivity (ρ) with the relative concentration of hole and electron doping in the system. The samples showed varying amounts of colossal magnetoresistance depending upon temperature and applied magnetic field. The magnetoresistance values as high as 72% were observed in x=0 sample.     

Synthesis, structural and transport properties of nanocrystalline La1−xBaxMnO3 (0.0≤x≤0.3) powders

Nanocrystalline La_1−xBa_xMnO₃ (0.0≤x≤0.3) manganites have been prepared by a simple and instantaneous solution combustion method, which is a low temperature initiated synthetic route to obtain fine-grained powders with relatively high surface area. The phase purity and crystal structure of the combustion products are carried out by powder X-ray diffraction. The as-made nanopowders are in cubic phase. On calcination to 900 °C, barium doped manganites retain cubic phase, whereas barium free manganite transformed to rhombohedral phase. The scanning electron microscope (SEM) results revealed that the combustion-derived compounds are agglomerated with fine primary particles. The doped manganites have surface area in the range 24-44 m²/g. The surface area of the manganites increases with barium content, whereas it decreases on calcination. Both undoped and doped lanthanum manganites show two active IR vibrational modes at 400 and 600 cm⁻¹. The low temperature resistivity measurements have been carried out by four-probe method down to 77 K. All the samples exhibit metal-insulator behaviour and metal-insulator transition temperature (T_M-I) in the range 184-228 K and it is interesting to note that, as the barium content increases the T_M-I shifts to lower temperature side. The maximum T_M-I of 228 K is observed for La_0.9Ba_0.1MnO₃ sample.     

Structural and electrical characterization of SxSe100−x thin films

Thin films of samples of the glassy S_xSe_100−x system with 0 ≤ x ≤ 7.28 have been prepared by thermal evaporation technique at room temperature (300 K). X-ray investigations show that the structure of pure selenium (Se) does change seriously by the addition of small amount of sulphur S ≤7.28%. The lattice parameters were determined as a function of sulphur content. Results of differential thermal analysis (DTA) of the glassy compositions of the system S_xSe_100−x were discussed. The characteristic temperatures (T_g, T_c and T_m) were evaluated. Dark electrical resistivities, ρ, of S_xSe_100−x thin films with different thicknesses from 100 to 500 nm, were measured in the temperature range from 300 to 423 K. Two distinct linear parts with different activation energies were observed. The variation of electrical resistivity of examined compositions has been discussed as a function of the film thickness, temperature and the sulphur content. The application of Mott model for the phonon assisted hopping of small polarons gave the same two activation energies obtained from the resistivity temperature calculations.     

Magnetic properties of Mn-rich Rh2Mn1+xSn1−x Heusler alloys

X-ray powder diffraction and magnetization measurements have been carried out on Rh₂Mn_1+xSn_1−x (0≤x≤0.3) alloys. The alloys, which crystallize in the L2₁ structure, were found to exhibit ferromagnetic behavior. The lattice constant a at room temperature decreases with increasing x, whereas the Curie temperature T_C decreases linearly. At 5 K the magnetic moment per formula unit first increases with increasing x and then saturates for x≥0.2. The experimental results are discussed in terms of the influence of the Mn-Mn exchange interactions between the Mn atoms on the Sn and Mn sites.     

Raman characterization of Pb2Na1−xLaxNb5−xFexO15 and Pb0.5(5−x)LaxNb5−xFexO15 (0≤x≤1) solid solutions

The ferroelectric compounds Pb₂Na_1−xLa_xNb_5−xFe_xO₁₅ and Pb_0.5(5−x)La_xNb_5−xFe_xO₁₅ (0≤x≤1) with the tungsten bronze type structure have been investigated using Raman spectroscopy. The evolution of the spectra as a function of composition at room temperature is reported. In the frequency range 200-1000 cm⁻¹ three main A₁ phonons around 240 (υ₁), 630 (υ₂) and 816 (υ₃) cm⁻¹ were observed. The broadening of the Raman lines for high values of x originates from a significant structural disorder. This is in good agreement with the relaxor character of these compositions. The lowest-frequency part of the spectra, below 180 cm⁻¹, reveals a structural change in the studied solid solutions. The behaviour of the Raman shift of the υ₁ mode confirms that in Pb₂Na_1−xLa_xNb_5−xFe_xO₁₅, a clear anomaly occurs in the vicinity of x=0.4.     

Structure, magnetic, and transport properties of the Co-doped manganites La0.9Te0.1Mn1−xCoxO3 (0≤x≤0.25)

The effect of Co doping at Mn-site on the structural, magnetic and electrical transport properties in electron-doped manganties La_0.9Te_0.1Mn_1−xCoxO₃ (0≤x≤0.25) has been investigated. The room temperature structural transition from rhombohedra to orthorhombic (Pbnm) symmetry is found in these samples with x≥0.20 by the Rietveld refinement of X-ray powder diffraction patterns. All samples undergo the paramagnetic-ferromagnetic (PM-FM) phase transition. The Curie temperature T_C of these samples decreases and the transition becomes broader with increasing Co-doping level. The magnetization magnitude of Co-doping samples increases at low temperatures with increasing Co-doping level for x≤0.15 and decreases with increasing Co-doping content further. The metal-insulator (M-I) transitions observed in the sample with x=0 are completely suppressed with Co doping, and the resistivity displays semiconducting behavior within the measured temperature region for these samples with x>0. All results are discussed according to the changes of the structure parameters and magnetic exchange interaction caused by Co-doping. In addition, the different effects between the Co doping and Cu doping in the Mn site for the electron-doped manganites are also discussed.     

Magnetic and magnetocaloric properties of Gd1−xScxNi2 solid solutions

Magnetic and heat capacity measurements have been carried out on the polycrystalline Gd_1−xSc_xNi₂ solid solutions (0≤x≤1), which crystallize in the cubic C15 Laves phases superstructure (space group F4?3m). These solid solutions are ferromagnetic with a Curie temperature below 76 K. Their Curie temperature decreases from 75.4 K for GdNi₂ to 13.6 K for Gd_0.2Sc_0.8Ni₂. At high temperatures, all solid solutions, except ScNi₂, are Curie-Weiss paramagnets. The Debye temperature as well as phonon, conduction electron and magnetic contributions to the heat capacity have been determined from heat capacity measurements. The magnetocaloric effect has been estimated both in terms of isothermal magnetic entropy change and adiabatic temperature change for selected solid solutions in magnetic fields up to 3 T.