Effect of light/dark cycle on bacterial hydrogen production by Rhodobacter sphaeroides RV

Hydrogen production by photosynthetic bacteria provides an efficient energy conversion method under low light intensity. However, under strong illumination, such as midday sunlight, the efficiency drops. This prevents the method from being applied industrially. To overcome this problem, we examined a method to thin out the excessive illumination. Light was given intermittently to reduce the total energy flux. The on/off ratio was set at 1/1 throughout the study, so that the time average of the light energy flux became half the continuous illumination. By keeping the time-average light flux constant (0.6 kW·m⁻²), the effects of the cycle period were examined in the range of hours to seconds. The hydrogen production rate was greatly affected by the cycle period, but cell growth and substrate consumption rates remained almost constant. The 30-min light/dark cycle (30 min on and 30 min off) provided the highest rate of hydrogen production (22 L·m⁻²·24 h⁻¹). At the shorter cycles, the rate decreased except that there was a suboptimum at about 40 s. Under excessive light intensity (1.2 kW·m⁻²), the light-to-hydrogen conversion efficiency was greatly enhanced. The hydrogen production rate during the 30-min cycle was twice as high as during a 12-h cycle under the same conditions.     

Development of an optical fibre reflectance sensor for p-aminophenol detection based on immobilised bis-8-hydroxyquinoline

2,2′-(1,4-Phenylenedivinylene)bis-8-hydroxyquinoline (PBHQ), a highly sensitive reagent used for the colorimetric determination of p-aminophenol (PAP), was successfully immobilised on XAD-7 and coupled with optical fibres to investigate a sensor-based approach for determining p-aminophenol. The solid-state sensor is based on the reaction of PAP with PBHQ in presence of an oxidant to produce an indophenol dye. The reflectance measurements were carried out at a wavelength of 647 nm since it yielded the largest divergence different in reflectance spectra before and after reaction with the analyte. The linear dynamic range of PAP was found within the concentration range of 0.1-2.18 mg l⁻¹ with its LOD of 0.02 mg l⁻¹. The sensor response from different probes (n = 7) gave a R.S.D. of 4.4% at 1.09 mg l⁻¹ PAP concentration. The response time of the optical one-shot sensor was 5 min for a stable solution. As this PAP sensor is irreversible, a fresh sensor has to be used for each measurement. All the experimental parameters were optimized for the determination of PAP. Using the optical sensing probe, PAP in pharmaceutical wastewater and paracetamol was determined. The effect of potential interferences such as inorganic and organic compounds was also evaluated. Potential on-site determination of PAP with such sensors can indirectly aid detection of organo-phosphorus nerve agents and pesticides in the field by inhibition of acetylcholine esterase-catalyzed hydrolysis of p-aminophenyl acetate to p-aminophenol.     

Electrochemical sensor for cinchonine based on a competitive host-guest complexation

An electrochemical sensor for cinchonine (CCN) using the β-cyclodextrin (β-CD) modified poly(N-acetylaniline) (PAA) electrode has been developed, in which 1,4-hydroquinone (HQ) was chosen as a probe. Complexation of HQ with β-CD modified on the glassy carbon electrode (GCE) was examined by cyclic voltammetry (CV). HQ was included in the cavity of β-CD and reversible voltammograms were observed. In the presence of CCN, a competitive inclusion equilibrium with β-CD was established between HQ and CCN, lowering the peak current of HQ. The decrease in the peak current of HQ is directly proportional to the amount of CCN. Linear calibration plot was obtained over the range from 4.0 × 10⁻⁶ to 8.0 × 10⁻⁵ M with a detection limit (S/N = 3) of 2.0 × 10⁻⁶ M. From the inhibitory effect of CCN on the inclusion of HQ by β-CD, the apparent formation constant of CCN with the immobilized β-CD was estimated. This electrochemical sensor showed excellent sensitivity, repeatability, stability and recovery for the determination of CCN. The response mechanism of the sensor was discussed in detail. The optimum steric configuration of inclusion complex was presented by molecular dynamics simulation.     

Surface plasmon resonance sensor for lysozyme based on molecularly imprinted thin films

Molecularly imprinted polymers (MIPs) selective for lysozyme were prepared on SPR sensor chips by radical co-polymerization with acrylic acid and N,N′-methylenebisacrylamide. Gold-coated SPR sensor chips were modified with N,N′-bis(acryloyl)cystamine, on which MIP thin films were covalently conjugated. The presence of NaCl during the polymerization and the re-binding tests affected the selectivity and the optimization of NaCl concentration in the pre-polymerization mixture and the re-binding buffer could enhance the selectivity in the target protein sensing. When the lysozyme-imprinted polymer thin films were prepared in the presence of 40 mM NaCl, the selectivity factor (target protein bound/reference protein bound) of MIP in the re-binding buffer containing 20 mM NaCl was 9.8, meanwhile, that of MIP in the re-binding buffer without NaCl was 1.2. A combination of SPR sensing technology with protein-imprinted thin films is a promising tool for the construction of selective protein sensors.     

在色氨酸存在下利用多壁碳纳米管糊电极和萘酚介质构成的伏安传感器测定N-乙酰半胱氨酸(英文)

A multiwall carbon nanotube modified electrode prepared by incorporating multiwall carbon nanotubes in the electrode of a sensor and naphthol green as a homogeneous mediator was used as a voltammetric sensor for the determination of N‐actylcysteine(N‐AC) in the presence of trypto-phan(Trp). The voltammograms of differential pulse voltammetry of N‐AC in a mixture with Trp were separated from each other by a potential difference of 200 mV, which allowed the determina-tion of both N‐AC and Trp simultaneously. Under the optimum conditions, the electrocatalytic cur-rents increased linearly with N‐AC concentration in the range of 0.25–400 μmol/L(two linear seg-ments with different slopes). The detection limit for N‐AC was 0.08 μmol/L. The kinetic parameters of the system were determined using electrochemical methods. The method was applied for the determination of N‐AC in drug and urine samples.     

Sensitive and selective electrochemical detection of artemisinin based on its reaction with p-aminophenylboronic acid

The electrochemical detection of artemisinin generally requires high oxidation potential or the use of complex electrode modification. We find that artemisinin can react with p-aminophenylboronic acid to produce easily electrochemically detectable aminophenol for the first time. By making use of the new reaction, we report an alternative method to detect artemisinin through the determination of p-aminophenol. The calibration curve for the determination of artemisinin is linear in the range of 2 μmol L⁻¹ to 200 μmol L⁻¹ with the detection limit of 0.8 μmol L⁻¹, which is more sensitive than other reported electrochemical methods. The relative standard deviation is 4.83% for the determination of 10 μM artemisinin. Because the oxidation potential of p-aminophenol is around 0 V, the present method is high selective. When 40 μM, 90 μM and 140 μM of artemisinin were spiked to compound naphthoquine phosphate tablet samples, the recoveries are 107.6%, 105.4% and 101.7%, respectively. This detection strategy is attractive for the detection of artemisinin and its derivatives. The finding that artemisinin can react with aromatic boronic acid has the potential to be exploited for the development of other sensors, such as fluorescence artemisinin sensors.     

Thermodynamic approach for studying both the retention and complexation mechanisms with hydroxy-propyl-beta-cyclodextrin of a phenoxy-propionic acid herbicide series

The retention and complexation mechanisms of a herbicide series were studied from a chromatographic approach using a novel column called “Nautilus^®”. The effects of water fraction and the hydroxy-propyl-β-cyclodextrin (HP-β-CD) concentration in the mobile phase were analysed in relation to the column temperature. Two retention models of phenoxy-propionic acid (PPA) derivatives were investigated. It was shown that the retention mechanism was led by free PPA herbicide for low HP-β-CD concentrations and by the PPA/HP-β-CD complex for the highest ones. In addition, an enthalpy-entropy compensation study revealed that both the solute retention and complexation mechanisms were independent of the number of chlorine atoms in the structure. Also the thermodynamic results showed that (1) the retention process depended on the water fraction (X) in the mobile phase and (2) the PPA/HP-β-CD complexation mechanism was shown to be entropically controlled.     

Development of an N-sulfinyl prolinamide for the asymmetric aldol reaction

A new class of organocatalysts is reported that incorporates an N-sulfinyl amide in place of the carboxylic acid of proline to serve as a hydrogen bond donor, chiral directing group, and solubilizing element. The successful application of this type of catalyst to the asymmetric aldol reaction of acetone and aryl aldehydes, for which proline performs poorly, is also described.     

DAB-Cy as an inexpensive and effective ligand for palladium-catalyzed homocoupling reaction of aryl halides

A novel catalytic system of PdCl₂(CH₃CN)₂ with N,N′-dicyclohexyl-1,4-diazabutadiene (DAB-Cy) ligand was successfully used in reductive coupling of aryl halides.     

Peptide thioester preparation based on an N-S acyl shift reaction mediated by a thiol ligation auxiliary

Formation of peptide thioesters, based on an N to S acyl shift mediated by an auxiliary, N-4,5-dimethoxy-2-mercaptobenzyl (Dmmb) group, under acidic conditions, is described. The protected peptide was assembled on a hydroxymethylphenylacetamidomethyl resin via an N-Dmmb-amino acid residue according to standard Fmoc solid-phase peptide synthesis following treatment with trifluoroacetic acid. The peptide α-thioester was released from the resin by reaction with 2-mercaptoethanesulfonic acid in the presence of N,N-diisopropylethylamine.     

Novel coated-graphite membrane sensor based on N,N′-dimethylcyanodiaza-18-crown-6 for the determination of ultra-trace amounts of lead

A novel selective membrane electrode for determination of ultra-trace amount of lead was prepared. The PVC membrane containing N,N′-dimethylcyanodiaza-18-cown-6 (DMCDA18C6) directly coated on a graphite electrode, exhibits a Nernstian response for Pb²⁺ ions over a very wide concentration range (from 1.0×10⁻² to 1.0×10⁻⁷ M) with a limit of detection of 7.0×10⁻⁸ M (∼14.5 ppb). It has a fast response time of ∼10 s and can be used for at least 2 months without any major deviation in potential. The electrode revealed very good selectivity with respect to all common alkali, alkaline earth, transition and heavy metal ions. The proposed sensor was used as an indicator electrode in potentiometric titration of lead ions and in determination of lead in edible oil, human hair and water samples. The proposed sensor was found to be superior to the best Pb²⁺-selective electrodes reported in terms of detection limit and selectivity coefficient.     

Highly selective and sensitive simple sensor based on electrochemically treated nano polypyrrole-sodium dodecyl sulphate film for the detection of para-nitrophenol

An ultrasensitive and highly selective electrochemical sensor for the determination of p-nitrophenol (p-NP) was developed based on electrochemically treated nano polypyrrole/sodium dodecyl sulphate film (ENPPy/SDS film) modified glassy carbon electrode. The nano polypyrrole/sodium dodecyl sulphate film (NPPy/SDS film) was prepared and treated electrochemically in phosphate buffer solution. The surface morphology and elemental analysis of treated and untreated NPPy/SDS film were characterized by FESEM and EDX analysis, respectively. Wettability of polymer films were analysed by contact angle test. The hydrophilic nature of the polymer film decreased after electrochemical treatment. Effect of the pH of electrolyte and thickness of the ENPPy/SDS film on determination of p-NP was optimised by cyclic voltammetry. Under the optimised conditions, the p-NP was determined from the oxidation peak of p-hydroxyaminophenol which was formed from the reduction of p-NP in the reduction segment of cyclic voltammetry. A very good linear detection range (from 0.1 nM to 100 μM) and the best LOD (0.1 nM) were obtained for p-NP with very good selectivity. This detection limit is below to the allowed limit in drinking water, 0.43 μM, proposed by the U.S. Environmental Protection Agency (EPA) and earlier reports. Moreover, ENPPy/SDS film based sensor exhibits high sensitivity (4.4546 μA μM⁻¹) to p-NP. Experimental results show that it is a fast and simple sensor for p-NP.     

Development of ratiometric fluorescent pH sensors based on chromenoquinoline derivatives with tunable pKa values for bioimaging

In this work, we first studied the pH-dependent characteristic of chromenoquinoline. Based on this, we then designed and synthesized two novel chromenoquinoline derivatives that can act as fluorescent pH sensors. The pK_a values of two novel chromenoquinoline derivatives can be modulated from 2.32 to 4.38 and 6.27 by introducing EDG on the backbone of chromenoquinoline. Furthermore, we demonstrate that the sensor 4 can be used as a ratiometric fluorescent pH sensor for fluorescence imaging in living cells.     

Reusable sensor based on functionalized carbon dots for the detection of silver nanoparticles in cosmetics via inner filter effect

We report a low cost selective analytical method based on inner filter effect (IFE) for citrate-silver nanoparticle (cit-AgNP) detection, in which fluorescent amine-derivatized carbon dots (a-CDs) act as the donor and aggregated cit-AgNPs as the energy receptor. Carbon dots (CDs) were chemically modified with ethylenediamine (EDA) moieties via amidic linkage displaying an emission band at 440 nm. The presence of cit-AgNPs produces a remarkably quenching of a-CD fluorescence via IFE, since the free amine groups at CD surface induce the aggregation of cit-AgNPs accompany by a red-shifting of their characteristic plasmon absorption wavelength, which resulted in “turn-on” of the IFE-decreased in CD fluorescence. The proposed method, which involves the use of chelating agents for removal of metal ions interferences, exhibits a good linear correlation for detection of cit-AgNPs from 1.23 × 10⁻⁵ to 6.19 × 10⁻⁵ mol L⁻¹, with limits of detection (LOD) and quantification (LOQ) of 5.17 × 10⁻⁶ and 1.72 × 10⁻⁵ mol L^−1, respectively. This method demonstrates to be efficient and selective for the determination of cit-AgNPs in complex matrices such as cosmetic creams and reveals many advantages such as low cost, reusability, high sensitivity and non time-consuming compared with other traditional methods.     

Ultrasensitive electrochemical sensor for p-nitrophenyl organophosphates based on ordered mesoporous carbons at low potential without deoxygenization

p-Nitrophenyl organophosphates (OPs) including paraoxon, parathion and methyl parathion, etc, are highly poisonous OPs, for which sensitive and rapid detection method is most needed. In this work, an ultrasensitive electrochemical sensor for the determination of p-nitrophenyl OPs was developed based on ordered mesoporous carbons (OMCs) modified glassy carbon electrode (GCE) (OMCs/GCE). The electrochemical behavior and reaction mechanism of p-nitrophenyl OPs at OMCs/GCE was elaborated by taking paraoxon as an example. Experimental conditions such as buffer pH, preconcentration potential and time were optimized. By using differential pulse voltammetry, the current response of the sensor at −0.085 V was linear with concentration within 0.01–1.00 μM and 1.00–20 μM paraoxon. Similar linear ranges of 0.015–0.5 μM and 0.5–10 μM were found for parathion, and 0.01–0.5 μM and 0.5–10 μM for methyl parathion. The low limits of detection were evaluated to be 1.9 nM for paraoxon, 3.4 nM for parathion and 2.1 nM for methyl parathion (S/N = 3). Common interfering species had no interference to the detection of p-nitrophenyl OPs. The sensor can be applicable to real samples measurement. Therefore, a simple, sensitive, reproducible and cost-effective electrochemical sensor was proposed for the fast direct determination of trace p-nitrophenyl OPs at low potential without deoxygenization.     

A nonenzymatic optical immunoassay strategy for detection of Salmonella infection based on blue silica nanoparticles

A novel nonenzymatic optical immunoassay strategy was for the first time designed and utilized for sensitive detection of antibody to Salmonella pullorum and Salmonella gallinarum (S. pullorum and S. gallinarum) in serum. The optical immunoassay strategy was based on blue silica nanoparticles (Blue-SiNps) and magnetic beads (MB). To construct such an optical immunoassay system, the Blue-SiNPs were first synthesized by inverse microemulsion method, characterized by SEM, Zeta potential and FTIR. Two nanostructures including Blue-SiNPs and MB were both functionalized with antibody against S. pullorum and S. gallinarum (anti-PG) without using enzyme labeled antibody. Anti-PG functionalized blue silica nanoparticles (IgG-Blue-SiNps) were used as signal transduction labels, while anti-PG functionalized magnetic beads (IgG-MB) were selected to separate and enrich the final sandwich immune complexes. In the process of detecting negative serum, a sandwich immunocomplex is formed between the IgG-MB and IgG-Blue-SiNPs. With the separation of the immunocomplex using an external magnetic field, the final plaque displayed bright blue color. While in the detection of infected serum, IgG-MB and anti-PG formed sandwich immunocomplexes, IgG-Blue-SiNPs were unable to bind to the limited sites of the antigen, and a light brown plaque was displayed in the bottom of microplate well. Stable results were obtained with an incubation time of 60 min at room temperature, and different colors corresponding to different results can be directly detected with naked eye. The reaction of IgG-Blue-SiNPs with S. pullorum was inhibited by 1:100 dilution of positive chicken serum. Such a simple immunoassay holds great potential as sensitive, selective and point-of-care (POC) tool for diagnosis of other biological molecules.     

A rapid method for the detection of foodborne pathogens by extraction of a trace amount of DNA from raw milk based on amino-modified silica-coated magnetic nanoparticles and polymerase chain reaction

A method based on amino-modified silica-coated magnetic nanoparticles (ASMNPs) and polymerase chain reaction (PCR) was developed to rapidly and sensitively detect foodborne pathogens in raw milk. After optimizing parameters such as pH, temperature, and time, a trace amount of genomic DNA of pathogens could be extracted directly from complex matrices such as raw milk using ASMNPs. The magnetically separated complexes of genomic DNA and ASMNPs were directly subjected to single PCR (S-PCR) or multiplex PCR (M-PCR) to detect single or multiple pathogens from raw milk samples. Salmonella Enteritidis (Gram-negative) and Listeria monocytogenes (Gram-positive) were used as model organisms to artificially contaminate raw milk samples. After magnetic separation and S-PCR, the detection sensitivities were 8 CFU mL⁻¹ and 13 CFU mL⁻¹ respectively for these two types of pathogens. Furthermore, this method was successfully used to detect multiple pathogens (S. Enteritidis and L. monocytogenes) from artificially contaminated raw milk using M-PCR at sensitivities of 15 CFU mL⁻¹ and 25 CFU mL⁻¹, respectively. This method has great potential to rapidly and sensitively detect pathogens in raw milk or other complex food matrices.     

Effect of reaction solvent on the preparation of thermo-responsive stationary phase through a surface initiated atom transfer radical polymerization

Poly(N-isopropylacrylamide) (PIPAAm) brush grafted silica beads, a thermo-responsive chromatographic stationary phase, were prepared through a surface-initiated atom transfer radical polymerization (ATRP) using 2-propanol, N,N-dimethylformamide (DMF), and water as reaction solvents. The rate of grafting PIPAAm on silica bead surfaces was different and found to be dependent on the reactivity of reaction solvent. Temperature-dependent elution profiles of hydrophobic steroids from the prepared-beads-packed columns were found to be different, although the graft amounts of PIPAAm were similar on silica bead surfaces. Especially, prepared beads using 2-propanol exhibited a higher resolution than those using DMF. Calibration curves using glucose and pullulan suggested that beads prepared using DMF prohibited analytes to diffuse into the pores. On the contrary, beads prepared using 2-propanol allowed analytes to diffuse into the pores. The pore diameter of the prepared beads, measured by N(2) adsorption-desorption measurement, suggested that beads using 2-propanol has relatively larger pore diameter than those using DMF. Thus, the reaction solvent in surfaces-initiated ATRP affected the grafting configuration of PIPAAm on porous silica-bead surfaces, leading to the different separation efficiency of stationary phase for bioactive compounds.