Application of an optimization procedure in adsorptive stripping voltammetry for the determination of trace contaminant metals in aqueous medium

A procedure for the determination of the contaminant metal In(III) by differential pulse adsorptive stripping voltammetry (DPAdSV) using ammonium pyrrolidine dithiocarbamate (APDC) as a complexing agent, has been optimized. The selection of the experimental conditions was made using experimental design methodology by means of a robust regression method which allows the elimination of anomalous points. The detection limit obtained was 1.3×10⁻⁹ mol dm⁻³. Possible interferences from concomitant metal ions were evaluated. Among all the metals analyzed, only Cd(II) was found to create an interference. This fact made impossible to carry out the determination of In(III) in the presence of Cd(II) using a univariate calibration. This problem was solved using multivariate regression techniques such as partial least squares (PLS). The procedure was successfully applied to the determination of indium in different aqueous samples.     

Crown ethers in stripping voltammetry of palladium

The similarity in the structures (presence of hexatomic rings) of crown ethers and graphite is used for adsorptive modification of the graphite electrode surface. The effect is exploited in stripping voltammetry for the determination of palladium. Anodic currents observed at potentials of 0.6 to 0.65 V (vs. Ag/AgCI electrode) are the source of information about adsorption of the crown ethers. Maximum adsorption of the reagents takes place at potentials close to the potential of zero charge of graphite. Deposition of palladium on the electrode surface is enhanced, the closer the values of the diameters of the crown-ether rings and Pd(II) are.     

Determination of gallium by adsorptive stripping voltammetry

A procedure for the determination of gallium by differential pulse adsorptive stripping voltammetry (DPADSV), using different complexing agents (ammonium pyrrolidine dithiocarbamate (APDC), pyrocatechol violet (PCV) and diethyldithiocarbamate (DDTC)), has been optimized. The selection of the experimental conditions was made using experimental design methodology. Under these conditions, the calibration was made and the detection limit was determined for each gallium-ligand complex. A robust regression method was applied which allowed the elimination of anomalous points. The detection limit, with α=β=0.05, for gallium-APDC complex was 5.0×10⁻⁸ mol dm⁻³, for gallium-PCV complex was 9.9×10⁻⁹ mol dm⁻³, and the lowest detection limit (1.3×10⁻⁹ mol dm⁻³) was obtained with DDTC. For this reason, DDTC was selected for the determination of the gallium concentration in a certificate sample and in a spiked tap water sample. The linear dynamic range for gallium-APDC complex was from 5.0×10⁻⁸ to 2.7×10⁻⁷ mol dm⁻³, for gallium-PCV complex was from 5.0×10⁻⁹ to 4.8×10⁻⁷ mol dm⁻³, and for gallium-DDTC complex was from 1.0×10⁻⁹ to 2.1×10⁻⁷ mol dm⁻³.     

Speciation of antimony by adsorptive stripping voltammetry using pyrogallol

This paper describes a new procedure for the determination of Sb (III) and Sb (V) by differential pulse adsorptive stripping voltammetry (DPAdSV) using pyrogallol as a complexing agent. The selection of the experimental conditions was made using experimental design methodology. The detection limits obtained were 1.03 × 10⁻¹⁰ and 9.48 × 10⁻⁹ mol dm⁻³ for Sb (III) and Sb (V), respectively.In order to carry out the simultaneously determination of both antimony species a partial least squares regression (PLS) is employed to resolve the voltammetric signals from mixtures of Sb (III) and Sb (V) in the presence of pyrogallol. The relative error in absolute value is less than 0.5% when concentrations of several mixtures are calculated. Moreover, the solution is analyzed for any possible effects of foreign ions. The procedure is successfully applied to the speciation of antimony in pharmaceutical preparations and water samples.     

Determination of traces molybdenum by catalytic adsorptive stripping voltammetry

A reliable and very sensitive procedure for the determination of ultra trace of molybdenum is proposed. Molybdenum was determined by cathodic stripping differential pulse voltammetry based on the adsorption collection of the Mo(VI)-Tiron complex on a hanging mercury drop electrode (HMDE). The variation of peak current with pH, concentration of Tiron and chlorate, plus several instrumental parameters such as accumulation time, accumulation potential and scan rate, were optimized. Under optimized condition, the relationship between the peak current and molybdenum concentration is linear in the range of 0.010-21.0 ng ml⁻¹. The limit of detection was found to be 0.006 ng ml⁻¹. The relative standard deviation for 10 replicates determination of 0.6 and 10 ng ml⁻¹ Mo(VI) is equal to 1.3 and 0.9%, respectively. The method was applied to the determination of molybdenum in river water, tap water, well water, plant foodstuff samples such as cucumber, tomato, carrot, and certified steel reference materials.     

Effect of chromatographic parameters and detector settings on the response of HILIC-evaporative light-scattering detection system using experimental design approach and multicriteria optimization methodology

Four polar compounds, i.e. pantothenic acid, inositol, taurine and caffeine were used as probe solutes in conjunction with chemometric methods to find out meaningful implications of chromatographic conditions and detector settings on the system performance. Putting a premium on the conditions of hydrophilic interaction liquid chromatography (HILIC) and settings of evaporative light-scattering detection (ELSD), we scrutinize the importance of certain factors on signal-to-noise ratio and its variability. The application of a central composite design reveals that caffeine, which sublimes, differentiates from the relatively thermosensitive pantothenic acid as well as from inositol and taurine, which are thermostable, do not sublime and have high melting points. It seems that prior knowledge of solute characteristics is critical to estimate the chromatographic response as a function of chromatographic conditions and detection settings. Reducing the responses to just one by combining them “ad hoc”, results in an overall desirability function, which brings out the global optimal chromatographic conditions and detector settings.     

Batch-injection stripping voltammetry (tube-less flow-injection analysis) of trace metals with on-line sample pretreatment

The most essential limitation of batch-injection analysis (BIA) methodology compared to other flow methods (CFA, FIA, SIA) is the lack of possibility of on-line sample processing in the measuring system. Some procedures of on-line sample pretreatment in BIA are possible by changing the plastic tip of the automatic micropipette used for sample injection into a flow-through reactor, e.g. by packing it with a bed of a solid sorbent. This concept is employed in the voltammetric stripping determinations of trace metals using a bed of commercial chelating resin Chelex-100. It was found that, besides the electrochemical preconcentration of analytes in the form of amalgams on the surface of mercury thin film electrodes, an approximately 10-fold additional preconcentration can be achieved on the packed sorbent bed by using different volumes of aspirated sample solution and eluent. This procedure allows also efficient elimination of some matrix effects.     

An optimization procedure for determination of indomethacin and acemethacin by differential pulse adsorptive stripping voltammetry. Application on urine samples

Procedures for the determination of indomethacin and acemethacin by differential pulse adsorptive stripping voltammetry with a mercury electrode have been described and optimised. The selection and optimization of the experimental parameters was done using factorial and central composite designs. Indomethacin and acemethacin in urine were determined by this method with good results and without the need for tedious prior separation. For routine calibration and calculation of the ‘capacity to detect’, the robust regression method least median squares (LMS) has been proposed.     

Standard addition method applied to solid-state stripping voltammetry: determination of zirconium in minerals and ceramic materials

An application of the standard addition method to stripping voltammetry of solid materials immobilized in inert electrodes is described. The method allows the determination of the mass fraction of a depositable metal M in a material on addition of known amounts of a standard material containing M to a mixture of that material and a reference compound of a second depositable metal, R. After a reductive deposition step, voltammograms recorded for those modified electrodes immersed in a suitable electrolyte produce stripping peaks for the oxidation of the deposits of M and R. If no intermetallic effects appear the quotients between the peak areas and the peak currents for the stripping oxidation of M and R vary linearly with the mass ratio of the added standard and the reference compound, thus providing an electrochemical method for determining the amount of M in the sample. The method has been applied to the determination of Zr in minerals, ceramic frits, and pigments, using ZnO as reference material and ZrO₂ as the standard.     

Application of gallium film electrode for elimination of copper interference in anodic stripping voltammetry of zinc

For elimination of copper interference in anodic stripping determinations of zinc at mercury and bismuth film electrodes gallium ions are usually added to the supporting electrolyte. In the presented studies novel ex situ formed gallium film electrode was applied for this purpose. The proposed electrode is less toxic than mercury one while the detection limit for zinc was lower than for bismuth film electrode following the same deposition time. The calibration graph for deposition time of 60 s was linear from 5 × 10⁻⁸ to 2 × 10⁻⁶ mol L⁻¹. The determinations of zinc were carried out from undeaerated solutions. The proposed procedure was applied to zinc determination in certified reference material and tap water sample.     

Some observations on the accumulation potential in adsorptive stripping voltammetry

A newly named parameter, “initial scan potential”, the potential from which the voltammetric scan starts rather than the widely accepted accumulation potential, has been found to be responsible for some of the important features of voltammograms obtained in the adsorptive stripping voltammetry (AdSV) of some organochlorine compounds (DDT, Dieldrin, 2,4- dichlorophenoxyacetic acid, 2,4,5-trichlorophenoxyacetic acid). The experimental evidence reported strongly confirms the nonfaradaic nature of the preconcentration step in adsorptive stripping voltammetry.     

Use of a modified, high-sensitivity, anodic stripping voltammetry method for determination of zinc speciation in the North Atlantic Ocean

Zinc speciation is considered to be an important determinant of the biological availability of zinc. Yet in oceanic surface waters, characterization of zinc speciation is difficult due to the low concentrations of this essential micronutrient. In this study, an anodic stripping voltammetry method previously developed for the total determination of cadmium and lead was successfully adapted to the measurement of zinc speciation. The method differs from previous zinc speciation anodic stripping voltammetry methods in that a fresh mercury film is plated with each sample aliquot. The fresh film anodic stripping voltammetry method was compared to competitive ligand exchange cathodic stripping voltammetry in a profile from the North Atlantic Ocean. Results using the fresh film anodic stripping voltammetry method were similar to those determined using the cathodic stripping voltammetry method, though ligand concentrations determined by fresh film anodic stripping voltammetry were generally slightly higher than those determined by cathodic stripping voltammetry. There did not seem to be a systematic difference between methods for the estimates of conditional stability constants. The ligand concentration in the North Atlantic profile ranged from 0.9 to 1.5 nmol L⁻¹ as determined by fresh film anodic stripping voltammetry and 0.6 to 1.3 nmol L⁻¹ as determined by cathodic stripping voltammetry. The conditional stability constants determined by fresh film anodic stripping voltammetry were 10^9.8-10^10.5 and by cathodic stripping voltammetry were 10^9.8-10^11.3.     

Catalytic adsorptive stripping voltammetry determination of ultra trace amount of molybdenum using factorial design for optimization

A highly sensitive procedure is presented for the determination of ultra-trace concentration of molybdenum by catalytic adsorptive stripping voltammetry. The method is based on adsorptive accumulation of the molybdenum (Mo)-pyrocatechol violet (PCV) complex on to a hanging mercury drop electrode, followed by reduction of the adsorbed species by voltammetric scan using differential pulse modulation. The reduction current is enhanced catalytically by chlorate. The influence of variables was completely studied by factorial design analysis. Optimum analytical conditions for the determination of molybdenum were established. Molybdenum can be determined in the range 1.0 × 10⁻³-100.0 ng ml⁻¹ with a limit of detection of 0.2 pg ml⁻¹. The influence of potential interfering ions on the determination of molybdenum was studied. The procedure was applied to the determination of molybdenum in mineral water and some analytical grade substances with satisfactory results.     

Determination of As(III) and arsenic(V) in natural waters by cathodic stripping voltammetry at a hanging mercury drop electrode

A simple, fast and quantitative method was developed for the determination of As(III) and total inorganic arsenic (As (total)) in natural spring and mineral waters using square wave cathodic stripping voltammetry (SWCSV) at a hanging mercury drop electrode (HMDE). In the determination of As(III), pre-concentration was carried out on the electrode from a solution of 1 mol/l HCl in the presence of 45 ppm of Cu(II) at a potential of −0.39 V versus Ag/AgCl, and the deposited intermetallic compound was reduced at a potential of about −0.82 V versus Ag/AgCl. In the determination of As (total) the pre-concentration was carried out in 1 mol/l HCl in the presence of 400 ppm of Cu(II) at a potential of −0.40 V versus Ag/AgCl, and the intermetallic compound deposited was reduced at a potential of about −0.76 V versus Ag/AgCl. For determination of As(III) the quantification limit was 0.2 ppb for a deposition time of 40 s, and the relative standard deviation (R.S.D.) was calculated to be 6% (n=13) for a solution with 8 ppb of As(III). For As (total), the quantification limit was 2 ppb for a deposition time of 3 min, and the R.S.D. was calculated to be 3% (n=10) for a solution with 8 ppb of As(V). The method was validated by application of recovery and duplicate tests in the measurements of As(III) and As (total) in natural spring and mineral waters. For As (total), the results of the SWCSV method were compared with the results obtained by optical emission spectrometry with ICP coupled to hydride generation (OES-ICP-HG) good correlation being observed.     

Electrochemical studies and square wave stripping voltammetry of five common pesticides on poly 3,4-ethylenedioxythiophene modified wall-jet electrode

The cyclic voltammetric behavior of five common pesticides such as dicofol (DCF), cypermethrin (CYP), monocrotophos (MCP), chlorpyrifos (CPF) and phosalone (PAS) was investigated at a poly 3,4-ethylenedioxythiophene modified glassy carbon electrode (PEDOT/GCE). A method was developed for the detection and determination of these pesticides in trace level flowing stream, based on their redox behavior. The square wave stripping voltammetric principle was used to analyze the selected pesticides on PEDOT/GCE. Varying the accumulation potential and accumulation time, the best accumulation conditions were found out. Effects of initial scan potential, square wave pulse amplitude, step potential and frequency were examined for the optimization of stripping conditions. The peak current responses of analyte under optimum conditions were correlated over flow rate by using wall-jet PEDOT/GCE assembly. The calibration plots were linear over the pesticide's concentration range 0.10-72.60 μg l⁻¹ for DCF, 0.41-198.24 μg l⁻¹ for CYP, 0.22-220.95 μg l⁻¹ for MCP, 0.35-259.69 μg l⁻¹ for CPF and 1.07-141.46 μg l⁻¹ for PAS. The limit of detection was obtained between <0.09 and <1.0 μg l⁻¹ for five pesticides. It is low enough for trace pesticide determination in real samples. This method is applied for the determination of the five pesticides in soil samples. The recovery values obtained in spiked soil samples are 95.4 ± 5.4% for DCF, 93.7 ± 4.2% for CYP, 85.3 ± 8.4% for MCP, 94.6 ± 6.6% for CPF and 93.5 ± 4.9% for PAS.     

Determination of mobile form contents of Zn, Cd, Pb and Cu in soil extracts by combined stripping voltammetry

The amount of mobile forms of Zn, Pb, Cd and Cu in extracts obtained by treating soil samples with ammonium nitrate were determined by an appropriate combination of anodic and cathodic stripping voltammetry with hanging mercury drop electrode. Every analysis required three mercury drops: on the first one, zinc was determined; on the second, cadmium and lead; on the third, copper was determined. Zinc, lead and cadmium were determined by conventional differential-pulse anodic stripping voltammetry. For copper determination, adsorptive differential-pulse cathodic stripping voltammetry with amalgamation using chloride ions as a complexing agent was applied. The standard deviation of the results was from 1 to 10% depending on the metal content in the sample. Voltammetric results were in good agreement with the AAS analysis. No microwave digestion of soil extracts was necessary.     

Assay of anti-coagulant drug warfarin sodium in pharmaceutical formulation and human biological fluids by square-wave adsorptive cathodic stripping voltammetry

The cyclic voltammogram of the anti-coagulant drug warfarin sodium at the hanging mercury drop electrode exhibited a well-defined single two-electron irreversible peak over the pH range 4-7, which may be attributed to the reduction of the CO double bond of the drug molecule. Based on the interfacial adsorptive character of the drug onto the mercury electrode surface, a square-wave cathodic stripping procedure was optimized for its trace determination. The calibration plot was linear over the concentration range of 5×10⁻⁹ to 4×10⁻⁷ M warfarin sodium in Britton-Robinson (B-R) buffer of pH 5, with limits of detection and quantitation of 6.5×10⁻¹⁰ and 2.1×10⁻⁹ M warfarin sodium, respectively. The proposed procedure was successfully applied for assay of warfarin sodium in its pharmaceutical formulation “hemofarin tablets”, human serum and urine without the necessity for sample pretreatment or time-consuming extraction or evaporation steps, prior to assay of the drug. Limits of detection of 1.1×10⁻⁹ and 1.3×10⁻⁸ M warfarin sodium were achieved, while limits of quanitation of 3.7×10⁻⁹ and 4.3×10⁻⁸ M warfarin sodium were estimated in human serum and urine, respectively. The pharmacokinetic profiles of the drug were studied and the estimated pharmacokinetic parameters were favorably compared with those reported in literature.     

H-point standard addition method applied to solid-state stripping voltammetry: quantitation of lead and tin in archaeological glazes

A solid-state electrochemical application of the H-point standard addition method to the quantification of two depositable metals A and B, which produce strongly overlapped stripping peaks, is described. The method is based on the mechanical transference of mixtures of the solid sample plus a selected compound, of a reference depositable metal R, and of known amounts of a reference material containing A or B, to paraffin-impregnated graphite electrodes. After a reductive deposition step, voltammograms recorded for those modified electrodes immersed into a suitable electrolyte produce stripping peaks for the oxidation of all of the metals deposited. Measurement of the currents at selected potentials in overlapping peaks corresponding to the stripping of A and B permits the quantitation of these metals in the solid sample, while avoiding matrix effects. The method was applied to the simultaneous determination of Pb and Sn in archaeological glazes using PbCO₃ and SnO₂ as standards and ZnO as a reference material.      

Modified carbon-containing electrodes in stripping voltammetry of metals. Part II. Composite and microelectrodes

The second part of the review, which covers modified carbon-containing electrodes, describes composite and microelectrodes. Electrodes made of commercial and laboratory carbon-containing composite materials are discussed. Impregnated and thick-film electrodes and microelectrodes made of carbon fibers form a separate group. Various modifiers and methods of electrode modification are presented. Prospects for the future development of solid-state modified electrodes are considered.     

The renovated silver ring electrode in determination of lead traces by differential pulse anodic stripping voltammetry

The study of a new type of working electrode - the renovated silver ring electrode (RSRE) - for lead ions detection via differential pulse anodic stripping voltammetry (DP ASV) without removal of oxygen is reported. The only four constituents of the RSRE: a specially constructed silver ring electrode, a silver sheet used as silver counter/quasi-reference electrode and a silicon O-ring, are fastened together in a polypropylene body. The renovation of this electrode is carried out through mechanical removal of solid contaminants and electrochemical activation in the electrolyte which fills the RSRE body. Excellent repeatability and reproducibility - also in organic samples solutions - were reached in a period of a few weeks through the renovation of the electrode surface before each measurement. The reduction and stripping of lead on silver electrode under the DP ASV conditions are underpotential deposition/dissolution phenomena. The RSRE is used for the determination of Pb ions in concentrations ranging from 1 × 10⁻⁹ to 1 × 10⁻⁷ M. The repeatability of DP ASV runs in synthetic solutions covering the entire concentration range is better than 2%. Obtained calibration curves are represented by a correlation coefficient of at least 0.999. The detection limit (LOD) for the time of electrodeposition equal to 60 s is 0.2 × 10⁻⁹ M. LOD for Pb²⁺ detection at the RSRE is similar to this reported for a rotating silver electrode in subtractive anodic stripping voltammetry (E. Kirowa-Eisner, et al., Anal. Chim. Acta, 385 (1999) 325). The analysis of Pb²⁺ in synthetic solutions with and without surfactants, certified reference materials and natural water samples have been performed.