Room-temperature luminescence optosensings based on immobilized active principles actives: Application to nafronyl and naproxen determination in pharmaceutical preparations and biological fluids

This paper presents two easy and selective methods for determining the active principles nafronyl (NFL) and naproxen (NAP), using a flow-through fluorescence optosensor based on the on-line immobilization on a nonionic-exchanger (Silica Gel, Davisil™ and Amberlite XAD 7, respectively) solid support. The determination was performed in 5×10⁻³ M HAc/NaAc buffer solution at pH 5 for NFL and 15×10⁻³ M glycine/HCl buffer solution at pH 2.5 for NAP at a working temperature of 20 °C. The fluorescence intensities were measured at λ_ex/em=294/336 nm and λ_ex/em=332/354 nm for NFL and NAP, respectively. The response time for these optosensors were practically instant, obtaining a linear concentration range between 0 and 700.0 ng ml⁻¹ with a detection limit of 20.8 ng ml⁻¹, an analytical sensitivity of 10.1 ng ml⁻¹ and a standard deviation of 1.27% at a 500 ng ml⁻¹ concentration level for NFL and a linear concentration range between 0 and 200.0 ng ml⁻¹ with the detection limit of 13.3 ng ml⁻¹, an analytical sensitivity of 6.0 ng ml⁻¹ and a standard deviation of 3.52% at a 100 ng ml⁻¹ concentration level for NAP. The proposed methods were satisfactorily applied to real samples (three commercial formulations and urine samples). The effects of the possible interferences were evaluated in all cases.     

Ferric nanoparticle-based resonance light scattering determination of DNA at nanogram levels

A novel assay of DNA has been proposed by using ferric nanoparticles as probes coupled with resonance light scattering (RLS) detection. At pH 7.40, the RLS intensity of ferric nanoparticles can be greatly enhanced by the aggregation of positively charged ferric nanoparticles through electrostatic interaction with negatively charged DNA. The enhanced intensity of RLS at 452 nm is proportional to the concentration of DNA in the range of 0.01-0.8 μg ml⁻¹ for calf thymus and salmon sperm DNA and in the range of 0.005-0.3 μg ml⁻¹ for E. coli K12 genomic DNA. Detection limits are 3.6 ng ml⁻¹ for calf thymus DNA, 4.4 ng ml⁻¹ for salmon sperm DNA, and 1.9 ng ml⁻¹ for E. coli K12 genomic DNA, respectively. Compared with the chromophores previously used in RLS assay, the ferric nanoparticles have offered several advantages in easy preparation, good photostability and high sensitivity without being modified or functionalized.     

Studies on the supramolecular interaction between napropamide and β-cyclodextrin by spectrofluorimetry and its analytical application

The supramolecular interaction between N,N-diethyl-2-(1-naphthalenyloxy)propanamide (napropamide) and β-cyclodextrin (β-CD) has been studied by spectrofluorimetry. The results showed that β-CD reacted with napropamide to form an inclusion complex with an association constant of 3.18×10³ l mol⁻¹. The composition of the complex was 1:1 (β-CD:napropamide). Based on the significant enhancement of fluorescence intensity of napropamide in inclusion complex, a spetrofluorimetric method with high sensitivity and selectivity was developed for the determination of napropamide in aqueous solution. Under the optimum conditions, the complex had excitation and emission maxima at 285 and 339 nm, respectively. The linear range of the method was 3.7-1500 ng ml⁻¹ with a detection limit of 1.1 ng ml⁻¹. The proposed method was successfully used to determine napropamide in river water.     

An electrochemical biosensor for α-fetoprotein based on carbon paste electrode constructed of room temperature ionic liquid and gold nanoparticles

A novel and effective electrochemical immunosensor for the rapid determination of α-fetoprotein (AFP) based on carbon paste electrode (CPE) consisting of room temperature ionic liquid (RTIL) N-butylpyridinium hexafluorophosphate (BPPF₆) and graphite. The surface of the CPE was modified with gold nanoparticles for the immobilization of the α-fetoprotein antibody (anti-AFP). By sandwiching the antigen between anti-AFP on the CPE modified with gold nanoparticles and the secondary antibody, polyclonal anti-human-AFP labeled with horseradish peroxidase (HRP-labeled anti-AFP), the immunoassay was established. The concentration of AFP was determined based on differential pulse voltammetry (DPV) signal, which was generated in the reaction between O-aminophenol (OAP) and H₂O₂ catalyzed by HRP labeled on the sandwich immunosensor. AFP concentration could be measured in a linear range of 0.50-80.00 ng mL⁻¹ with a detection limit of 0.25 ng mL⁻¹. The immunosensor exhibited high sensitivity and good stability, and would be valuable for clinical assay of AFP.     

Sensitive fluorimetric method for the determination of aniline by using tetra-substituted amino aluminium phthalocyanine

This is the first report of the determination of aniline with tetra-substituted amino aluminium phthalocyanine (TAAlPc) by a fluorimetric method. In KBr-HCl solution, nitrite ion diazotizes TAAlPc, thus, the fluorescence of TAAlPc is dramatically quenched. However, there is less quenching in the presence of aniline and the recovery in fluorescence intensity is linear with the concentration of aniline. Based on this, a novel method has been developed for the determination of aniline in aqueous solutions. Under the optimal conditions, the calibration graph for aniline is from 5 to 300 ng ml⁻¹ with a 3σ limit of detection of 1.8 ng ml⁻¹. The relative standard deviation for nine replicate measurements of 100 ng ml⁻¹ aniline is 1.7%. The method was applied to the analysis of water samples with satisfactory results.     

Electrochemiluminescence assay for the detection of acridinium esters

An electrochemiluminescence (ECL)-based method for rapid and sensitive detection of acridinium ester in neutral solution was described. Strong ECL emission was observed when a positive voltage over 2.0 V (versus Ag/AgCl) was applied to the working electrode (Pt) immersed in the acridinium ester solution of 2.0 mol l⁻¹ KNO₃ (pH 7.0). The possible ECL mechanism was discussed. It was proposed that the ECL emission came out of N-methylacridone, the oxidization product of acridinium ester by the nascent oxygen generated on the surface of working electrode in the course of oxidization of water. Other influenced factors including the electrochemical parameters, the ECL reaction medium and pH value, were investigated in detail. Under the optimal conditions, ECL intensity has a linear relationship with the concentration of acridinium ester in the range of 0.24-96 ng ml⁻¹ (r=0.9999). The relative standard deviation for 24 ng ml⁻¹ acridinium ester was 4.6% (n=11). The limit of detection was 0.16 ng ml⁻¹.     

Hydride generation atomic fluorescence spectrometric determination of ultratraces of selenium and tellurium in cow milk

A sensitive procedure has been developed for selenium and tellurium determination in milk by hydride generation atomic fluorescence spectrometry (HG-AFS) after microwave-assisted sample digestion. The method provides sensitivity values of 1591 and 997 fluorescence units ng⁻¹ ml⁻¹ with detection limits of 0.005 and 0.015 ng ml⁻¹ for Se and Te, respectively. The application of the developed methodology to the analysis of cow milk samples of the Spanish market evidenced the presence of concentration ranges from 11.1 to 26.0 ng ml⁻¹ for Se, and from 1.04 to 9.7 ng ml⁻¹ for Te having found a good comparability with data obtained after dry-ashing of samples.     

Group-specific enzyme-linked immunosorbent assay for fenitrooxon and 3-methyl-4-nitrophenol in water samples based on a polyclonal antibody

Fenitrooxon [O,O-dimethyl-O-(4-nitro-m-tolyl)phosphate] is the major metabolite of the organophosphorus insecticide fenitrothion, and 3-methyl-4-nitrophenol is its major degradation product. In the present study, we describe the development of an indirect competitive enzyme-linked immunosorbent assay (ELISA) for the detection of these compounds in water samples based on a group-specific polyclonal antiserum generated with a “bifunctional hapten”, which has two functions: the conventional function of producing an antibody against an antigen and a unique function of promoting the production of the antibodies in rabbit. For application to water samples, the influence of several factors such as organic solvent, pH, and detergent was studied. Under optimized conditions, the quantitative working range of the fenitrooxon ELISA was 0.71-27 ng ml⁻¹ with a limit of detection (LOD) of 0.32 ng ml⁻¹, and the fenitrooxon concentration giving 50% reduction of the maximum signal (IC₅₀) was 4.2 ng ml⁻¹. The quantitative working range of the 3-methyl-4-nitrophenol ELISA was 0.67-27 ng ml⁻¹ with a LOD of 0.38 ng ml⁻¹ and an IC₅₀ of 3.7 ng ml⁻¹. No significant matrix effect originating from the water sample (river water, tap water, purified water, and bottled water) was shown by addition of Tween 20 to the assay buffer. Water samples spiked with each of these compounds at 1, 5, 10, and 20 ng ml⁻¹ were directly analyzed without extraction and clean-up by the proposed ELISA. The mean recovery was 100.9%, and the mean coefficient of variation (CV) was 7.7% for the fenitrooxon ELISA and for the 3-methyl-4-nitrophenol ELISA, the mean recovery was 97.6%, and the mean CV was 7.2%. The proposed ELISA allows precise and accurate determination of these compounds in water at such low levels.     

Near-infrared fluorimetric determination of nucleic acids by shifting the ion-association equilibrium between heptamethylene cyanine and Alcian blue 8GX

A new method based on near-infrared (near-IR) fluorescence recovery, employing a two-reagent system which is composed of an anionic heptamethylene cyanine (HMC) and a polycationic phthalocyanine dye, Alcian blue 8GX, is presented for the determination of nucleic acids. With a maximum excitation wavelength at 766 nm and a maximum emission wavelength at 796 nm, the fluorescence recovery is linear with the concentration of nucleic acids added. Factors including the acidity of the medium, the reaction time, the optimal ratio of the two reagents, as well as the influence of foreign substance were all investigated. Meanwhile, the mechanism of fluorescence recovery was also studied. Under the optimal conditions, the linear ranges of the calibration curves were 10-250 ng ml⁻¹ for calf thymus DNA (CT DNA) and 10-200 ng ml⁻¹ for yeast RNA. The detection limits were 6.8 ng ml⁻¹ for CT DNA and 6.3 ng ml⁻¹ for yeast RNA, respectively. The method has been applied to the analysis of practical samples and the recovery results were satisfactory.     

Determination of carbendazim, fuberidazole and thiabendazole by three-dimensional excitation-emission matrix fluorescence and parallel factor analysis

We simultaneously determined carbendazim, fuberidazole and thiabendazole by excitation-emission matrix (EEM) fluorescence in combination with parallel factor analysis (PARAFAC). Three-way deconvolution provided the pure analyte spectra from which we estimated the selectivity and sensitivity of the pesticides, and the relative concentration in the mixtures from which we established a linear calibration. Special attention was given calculating such figures of merit as precision, sensitivity and limit of detection (LOD), derived from the univariate calibration curve. The method, which had a relative precision of around 2-3% for the three pesticides, provided limits of detection of 20 ng ml⁻¹ for carbendazim, 4.7 ng ml⁻¹ for thiabendazole and 0.15 ng ml⁻¹ for fuberidazole. The accuracy of the method, evaluated through the root mean square error of prediction (RMSEP), was 27.5, 1.4, and 0.03 ng ml⁻¹, respectively, for each of the pesticides.     

Determination of nucleic acids based on the fluorescence quenching of Hoechst 33258 at pH 4.5

It was found the strong fluorescence emitted by the bis-benzimidazole derivative Hoechst 33258 at 490 nm could be efficiently quenched in pH 4.5 buffer when nucleic acids were added. Analysis of fluorescence intensity showed that the procedure was a static quenching dominated one, which was also demonstrated by the electron absorption spectra and lifetime of the excited state. The binding constant and numbers of binding sites were obtained from the Scatchard plot. The decreased fluorescence intensity was in proportion to the concentration of nucleic acids in the range 40-1800 ng ml⁻¹ for dsDNA and 26-1700 ng ml⁻¹ for ssDNA. The limits of detection were 12 and 8 ng ml⁻¹, respectively. The sensitivity of the method was about 3.4 times higher for dsDNA detection and 5.4 times higher for ssDNA detection compared with the widely used fluorescence enhancement method using the same dye. Application results to synthetic samples showed simplicity, rapidity and satisfactory reproducibility of the presented method. Measurement of real samples extracted from leaves of Crassula argentea and E. coli genome also gave satisfactory results, which were in good agreement with those obtained using spectrophotometric method.     

An immunoassay for bisphenol A based on direct hapten conjugation to the polystyrene surface of microtiter plates

Based on direct hapten coated format a competitive indirect enzyme-linked immunosorbent assay (ciELISA) for bisphenol A (BPA) was developed. Polystyrene surface was modified by 3-Aminopropyltriethoxysilane (APTES) to produce amino groups after H₂SO₄/HNO₃-pre-treatment. 4,4-bis (4-hydroxyphenyl) valeric acid (BVA) which is analogue of BPA, was successfully immobilized on the surface of microtiter plates by N,N′-dicyclohexylcarbodiimide (DCC) method. The essential steps of the assay were optimized, especially blocking procedure which is key step to prevent unspecific binding of antibody. The results indicated that compared with hapten-protein coated format (IC₅₀ = 176.67 ng ml⁻¹, LOD = 15.90 ng ml⁻¹), the direct hapten coated format (IC₅₀ = 23.50 ng ml⁻¹, LOD = 0.27 ng ml⁻¹) could improve assay sensitivity and the detection ranges were 2.30 ng∼157.60 ng ml⁻¹ with good signal reproducibility (P value > 0.05) after careful optimization of assay conditions. Tap water samples and seawater samples were spiked with a known amount of BPA and measured by ciELISA. The average recoveries were between 70 and 142%. As far as we are aware this is the most sensitive ELISA for BPA yet reported.     

Novel spectrofluorimetric method for the determination of sulfite with rhodamine B hydrazide in a micellar medium

A novel spectrofluorimetric method for the determination of sulfite using rhodamine B hydrazide as fluorogenic reagent in the presence of polyoxyethylene sorbitan monooleate (Tween 80) surfactant micelles is described. The method is based on the mixture of sulfite with rhodamine B hydrazide, a colorless, non-fluorescent substance in Tween 80 surfactant micelles which gives rhodamine B-like fluorescence emission. The fluorescence intensity increase is linearly related to the concentration of sulfite in the range 5-800 ng ml⁻¹ with a detection limit of 1.4 ng ml⁻¹ (3σ). The optimal conditions for the detection of sulfite are evaluated and the possible detection mechanism is also discussed. The method has been successfully applied to the determination of total sulfite in wines and compares well with the standard iodimetric method.     

Automatic on line preconcentration and determination of lead in water by ICP-AES using a TS-microcolumn

A simple, sensitive, low-cost and rapid, flow injection system for the on-line preconcentration of lead by sorption on a microcolumn packed with silica gel funtionalized with methylthiosalicylate (TS-gel) was developped. The metal is directly retained on the sorbent column and subsequently then eluted from it by EDTA. Five variables (sample flow rate, eluent flow rate, eluent concentration, pH and buffer concentration) were considered as factors in the optimization process. Interactions between analytical factors and their optimal levels were investigated using two level factorial and Box-Behnken designs. The optimum conditions established were applied to the determination of lead by flow injection inductively coupled plasma atomic emission spectrometry (FI-ICP-AES). The proposed method has a linear calibration range from 10 to at least 500 ng ml⁻¹ of lead. At a sample frequency of 24 h⁻¹ and a 120 s preconcentration time, the enrichment factor was 41, the detection limit was 15.3 ng ml⁻¹ (S/N=3) and the precision, expressed as relative standard deviation, was 0.9% (at 100 ng ml⁻¹). Validation of the developed method was carried out against electrothermal atomic absorption spectrometry analysis without statistically significant differences between the proposed method and the atomic absorption method.     

Quantification of sex pheromone from Anocentor nitens by gas chromatography-mass spectrometry-selected ion monitoring

Two highly sensitive and selective methods based on gas chromatography coupled to mass spectrometry (GC-MS) in the selected ion monitoring (SIM) mode have been developed for the quantification of 2,6-dichlorophenol (2,6-DCP), a sex pheromone of the tick females of Anocentor nitens. Standard addition method and calibration curve techniques using 5-bromine-4-hydroxy-3-methoxybenzaldehyde (5-BrV) as internal standard (IS) afforded detection limit of 0.1 ng ml⁻¹. The calibration curve was linear over the concentration range from 0.5 to 500 ng ml⁻¹ for 2,6-DCP. Results show that the concentration range of sex pheromone in the extracts samples was 1.08-10.35 ng ml⁻¹. The methods developed provided reliable procedures to determine amounts of 2,6-DCP present in ticks.     

Analysis of trace levels of domoic acid in seawater and plankton by liquid chromatography without derivatization,using UV or mass spectrometry detection

Quantitation of trace levels of domoic acid (DA) in seawater samples usually requires labour-intensive protocols involving chemical derivatization with 9-fluorenylmethylchloroformate and liquid chromatography with fluorescence detection (FMOC–LC–FLD). Procedures based on LC–MS have been published, but time-consuming and costly solid-phase extraction pre-concentration steps are required to achieve suitable detection limits. This paper describes an alternative, simple and inexpensive LC method with ultraviolet detection (LC–UVD) for the routine analysis of trace levels of DA in seawater without the use of sample pre-concentration or derivatization steps. Qualitative confirmation of DA identity in dubious samples can be achieved by mass spectrometry (LC–MS) using the same chromatographic conditions. Addition of an ion-pairing/acidifying agent (0.15% trifluoroacetic acid) to sample extracts and the use of a gradient elution permitted the direct analysis of large sample volumes (100 μl), resulting in both high selectivity and sensitivity (limit of detection = 42 pg ml⁻¹ by LC–UVD and 15 pg ml⁻¹ by LC–MS). Same-day precision varied between 0.4 and 5%, depending on the detection method and DA concentration. Mean recoveries of spiked DA in seawater by LC–UVD were 98.8% at 0.1–10 ng ml⁻¹ and 99.8% at 50–1000 ng ml⁻¹. LC–UVD exhibited strong correlation with FMOC–LC–FLD during inter-laboratory analysis of Pseudo-nitzschia multiseries cultures containing 60–2000 ng DA ml⁻¹ (r² > 0.99), but more variable results were obtained by LC–MS (r² = 0.85). This new technique was used to confirm the presence of trace DA levels in low-toxicity Pseudo-nitzschia spp. isolates (0.2–1.6 ng ml⁻¹) and in whole-water field samples (0.3–5.8 ng ml⁻¹), even in the absence of detectable Pseudo-nitzschia spp. cells in the water column.     

Direct spectrophotometric determination of calcium in clinical samples with carboxyazo-p-CH3

A highly sensitive and relatively interference-free spectrophotometric method for determination of calcium is described. The method is based on the reaction between calcium ions and carboxyazo-p-CH₃ in aqueous citrate medium of pH 7, to form a blue complex with maximum absorption at 716 nm. The calibration is linear up to 0.12 μg ml⁻¹ calcium with a repeatability (R.S.D.) of 1.0% at a concentration of 0.04 μg ml⁻¹ (n=5). The molar absorptivity of the complex and Sandell’s sensitivity are 3.5×10⁵ l mol⁻¹ cm⁻¹ and 0.11 ng cm⁻², its 10σ limit of quantification and the 3σ limit of detection were found to be 0.3 ng ml⁻¹ and 0.09 ng ml⁻¹ respectively. The influence of reaction variables and the effect of interfering ions are studied; no interference was observed in clinical samples. The proposed method has been applied directly to the determination of calcium in clinical samples without the need for pre-concentration, masking metal ions and digesting samples.     

Multiplex detection of tumor markers with photonic suspension array

A novel photonic suspension array was developed for multiplex immunoassay. The carries of this array were silica colloidal crystal beads (SCCBs). The codes of these carriers are the characteristic reflection peak originated from their structural periodicity, and therefore they do not suffer from fading, bleaching, quenching, and chemical instability. In addition, because no dyes or materials related with fluorescence are included, the fluorescence background of SCCBs is very low. With a sandwich format, the proposed suspension array was used for simultaneous multiplex detection of tumor markers in one test tube. The results showed that the four tumor markers, α-fetoprotein (AFP), carcinoembryonic antigen (CEA), carcinoma antigen 125 (CA 125) and carcinoma antigen 19-9 (CA 19-9) could be assayed in the ranges of 1.0-500 ng mL⁻¹, 1.0-500 ng mL⁻¹, 1.0-500 U mL⁻¹ and 3.0-500 U mL⁻¹ with limits of detection of 0.68 ng mL⁻¹, 0.95 ng mL⁻¹, 0.99 U mL⁻¹ and 2.30 U mL⁻¹ at 3σ, respectively. The proposed array showed acceptable accuracy, detection reproducibility, storage stability and the results obtained were in acceptable agreement with those from parallel single-analyte test of practical clinical sera. This technique provides a new strategy for low cost, automated, and simultaneous multiplex immunoassay.     

Determination of phenylurea herbicides in aqueous samples using partitioned dispersive liquid-liquid microextraction

Partitioned dispersive liquid-liquid microextraction (PDLLME), using THF as the dispersive solvent and dichloromethane as the extraction solvent, was utilized to isolate and concentrate phenylurea herbicides (PUHs) from aqueous samples. In PDLLME, a dispersive solvent should be able to partition in the organic extractant droplets to effectively extract the polar organic compounds from aqueous samples. The mixture of the water-immiscible extractant and the partitioned dispersive solvent was obtained by centrifugation, dried under low pressure, reconstituted in methanol-water mixture (1:1), and injected into a HPLC system for the determination of PUHs. The enrichment factors of the PUHs ranged from 68 to 126 under the optimal conditions. The linear range was 0.5-100 ng ml⁻¹ for each analyte, the relative standard deviations of PUHs were in the range of 1.5-5.9% (n = 5), and the detection limits (signal-to-noise ratio of 3) ranged from 0.10 to 0.28 ng ml⁻¹ for the herbicides. The range of intraday precision (n = 5) for PUHs at the levels of 0.5, 5, and 50 ng ml⁻¹ were 3.0-5.9%, 1.8-3.3%, and 2.2-3.6%, respectively. The range of interday precision (n = 5) at 0.5, 5, and 50 ng ml⁻¹ were 0.4-1.8%, 1.2-2.4%, and 0.9-2.3%, respectively. The recoveries of PUHs from three spiked river water samples, at a level of 10 ng ml⁻¹, were 91.2-104.1%. Due to its rapidity, ease of operation, and high recovery, PDLLME can be utilized to isolate and concentrate organic environmental contaminants such as PUHs from aqueous samples.     

Direct quantification of γ-globulin in human blood serum by resonance light scattering techniques without separation of human serum albumin

We describe the preparation and characterization of functionalized nano-PbS. The functionalized nanoparticles are water-soluble. Reaction of mercaptoacetic acid functionalized nano-PbS with γ-globulin (γ-IgG) results in an enhanced resonance light scattering (RLS) at 385 nm. Based on this, a new direct quantitative method for γ-globulin in blood serum samples without separation of human serum albumin is established. Under optimal conditions, the enhanced RLS intensity is in proportion to the γ-IgG concentration in the range 10-500 ng ml⁻¹. The 3σ limit of detection is 2.75 ng ml⁻¹. The contents of γ-IgG in blood serum samples were determined with a recovery of 97-104% and R.S.D. of 1.5-2.1% (n=6). This method proved to be very sensitive, rapid, simple and tolerant of most interfering substances.